Certification Exhibit FCC ID: 2ABLX-150017 IC: 8832A-150017 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-247 ACS Project Number: 15-0410 Manufacturer: Qmotion Incorporated Model: QM150017 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Warning: Changes or modifications to this device not expressly approved by QMotion Incorporated -Advanced Shading Systems could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equip-
ment should be installed and operated with minimum distance 20cm between the radiator and your body. This trans-
mitter must not be co-located or operating in conjunction with any other antenna or transmitter. INDUSTRY CANADA This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'uti-
lisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Cet quipement est conforme aux limites exposition aux radiations dans un environnement noncontrl. Cet quipement doit tre install et utilis distance minimum de 20cm entre le radiateur et votre corps. Cet metteur ne doit pas tre co-localises ou oprant en conjunction avec tout autre antenne ou transmetteur. QMotion ZigBee Hard Wired Control Roller Shade Application Guide REVISION 1.1 07DEC15 8 Part #
REVISION 1.1 07DEC15 Part #
ZigBee Hardwired Roller Shade System Overview ZigBee Hardwired Roller Shade Third Party Integration Power Distribution Panels 24 VDC Power Supplies RS485 Communication Third Party Integration Wire Specification:
Category 5e/Category 6 for use with RJ-45 Connector 24 AWG Maximum length of wire from Power Distribution Panel to device :
- 8 X 8 Shade with 40:1 motor - 1250
- 12 X 12 Shade with 73:1 motor - 750
- 12 X 20 Shade with 73:1 motor - 500
- Hardwired 4 and 8 Button Switches - 1000
*Length based on 115K baud rate Maximum wire length for RS485 communication - 2000 System Capacity:
200 Devices (QMotion Shades, QMotion Wireless Remotes, QMotion Hardwired Switches and other ZigBee devices) Power Distribution Panel:
8 RJ-45 ports for motorized shades and switches 2 additional RJ-45 communication ports dedicated to daisy chain with other Power Distribution Panels and Third Party Integration via RS485. Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A Note:
Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown). Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window .
*Specifications are subject to change without notice REVISION 1.1 07DEC15 7 Part #
Power Supply: 24 VDC, 7.5A RJ-45 Ports for Motorized Shades and Switches - Quantity 8 Communication Ports (RJ-45) - Quantity 2 REVISION 1.1 07DEC15 2 Part #
ZigBee Hardwired Roller Shade Third Party Integration ZigBee Hardwired Roller Shade Single Hardwired Switch Application 24 VDC Power Supplies Power Distribution Panels 24 VDC Power Supplies RS485 Communication Hardwired Switch Third Party Integration Power Distribution Panel 24 VDC Power Supply Hardwired Switch Wire Specification:
Category 5e/Category 6 for use with RJ-45 Connector 24 AWG Maximum length of wire from Power Distribution Panel to device:
- 8 X 8 Shade with 40:1 motor - 1250
- 12 X 12 Shade with 73:1 motor - 750
- 12 X 20 Shade with 73:1 motor - 500
- Hardwired 4 and 8 Button Switches - 1000
*Length based on 115K baud rate Maximum wire length for RS485 communication - 2000 System Capacity:
200 Devices (QMotion Shades, QMotion Hardwired Switches) Power Distribution Panel:
8 RJ-45 ports for motorized shades and switches ZigBee Remote Caution ZigBee Coordinator/
Router NOTE: The QMotion ZigBee Hardwired System does not operate on standard Power over Ethernet (PoE) schemes. Do not attempt to connect the QMotion ZigBee Hardwired System to any Ethernet device. Doing so may damage the system components and/or the external Ethernet or PoE device. 2 additional RJ-45 communication ports dedicated to daisy chain with other Power Distribution Panels and Third Party Integration via RS485. Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A Note:
Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown). Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window .
*Specifications are subject to change without notice REVISION 1.1 07DEC15 6 Part #
REVISION 1.1 07DEC15 3 Part #
ZigBee Hardwired Roller Shade ZigBee Hardwired Roller Shade Multiple Power Distribution Panel Application Wireless Remote / Optional Hardwired Switch Application Wire Specification:
Category 5e/Category 6 for use Power with RJ-45 Connector Distribution Panel 24 AWG Maximum length of wire from Power Distribution Panel to device:
- 8 X 8 Shade with 40:1 motor - 1250
- 12 X 12 Shade with 73:1 motor - 750
- 12 X 20 Shade with 73:1 motor - 500
- Hardwired 4 and 8 Button Switches - 1000
*Length based on 115K baud rate 24 VDC Power Supply Maximum wire length for RS485 communication - 2000 RS485 Communication System Capacity:
200 Devices (QMotion Shades, Power QMotion Hardwired Switches) Distribution Panel Power Distribution Panel:
8 RJ-45 ports for motorized shades and switches 2 additional RJ-45 commu-
nication ports dedicated to daisy chain with other Pow-
er Distribution Panels and Third Party Integration via RS485. Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A Hardwired Switch Power Distribution Panel 24 VDC Power Supply Wire Specification:
Category 5e/Category 6 for use with RJ-45 Connector 24 AWG Maximum length of wire from Power Distribution Panel to device:
- 8 X 8 Shade with 40:1 motor - 1250
- 12 X 12 Shade with 73:1 motor - 750
- 12 X 20 Shade with 73:1 motor - 500
- Hardwired 4 and 8 Button Switches - 1000
*Length based on 115K baud rate Maximum wire length for RS485 communication - 2000 System Capacity:
Hardwired Switch ZigBee Coordinator/
Router ZigBee Remote ZigBee devices) Power Distribution Panel:
8 RJ-45 ports for motorized shades and switches 2 additional RJ-45 communication ports dedicated to daisy chain with other Power Distribution Panels and Third Party Integration via RS485. Power Supply
- AC Input: 100-240 VAC, 2.5A
- DC Output: 24 VDC, 7.5A Note:
Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown). Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window . 24 VDC Power Supply 200 Devices (QMotion Shades, QMotion Wireless Remotes, QMotion Hardwired Switches and other Note:
Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown). Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window .
*Specifications are subject to change without notice
*Specifications are subject to change without notice REVISION 1.1 07DEC15 4 Part #
REVISION 1.1 07DEC15 5 Part #