FCC ID: G9H2-6928A 900 MHz Cordless Phone With Caller Id

We bring good things to.life. EqQuipMenT APPROVAL INFORMATION Your telephana equipment is approved for connection to the Public Switched Telephone Netvrork and is in compliance with parts 15 and 68, FCC Rules and Regulations and tha Technical Requirements for Telephone Terminal Equipment published by ACTA, 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number [REN) for the equipment, You must, upon request, pravide this information to your telephone company. Tha REN is useful in determining the number of devices you may connect to your telephone fine and still have all of these devices ring when your telephone number is called. In mast (but not al areas, the sum of the RENs of all devices connected to one line shoul net exceed 5, To be certain of the number of devices you may connect to your ine as determined by the REN, you should contact your local telephone company. Notes This equipment may not be used on coin service provided by the telephone company. :

* Party fines ara subject to state tariffs, and therefore, you may not be able ta use your own telephone equipment if you are on a party Sine, Check with your bocal telephone company.

+ Notice must be given to the telephone company upon permanent disconnection of your telephone from your Ene, 2 Rights of the Telephone Company ;

Should your equipment cause trouble on your line which may harm the telephone network, the talephone company shall, where practicable, notify you that temporary discontinuance of service may be required, Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. n case of such temporary discontinuance, the telephone company must: [1] promptly notify you of such temporary discontinuance; {2} afford you the opportunity to correct the situation; and (3) inform you of Your right ta bring a complaint to the Commission pursuant to procedures set forth in Subpart E af Part 68, FCC Rules and Regulations, i The telephone company may make changes in its communications facilities, equipment, operations or progedures where such action is required in the oparation of its business and not inconsistent with FCC Rules and Regulations, H these changes are expected to affact the use or performance of your telaphane equipment, the telephone comoary must give you adequate notice, in writing, $0 allow you to maintain uninterrupted service, i INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation, This equipment has been tested and found to comply with the Kmits for a Class B digital device, pursuant to Part $5 of the FCC Rules. These limits are designed to provide reasonable Protection against harmful interference in a residential instalation, This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, H this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate tl iving antenna (that is, the antenna for radio or television that is receiving the intesference},

* Reorient or relocate and increase the separation between tha telecommunications equipment ang racelving antenna,

* Connect the telecommunications equipment into an outlet on a circuit different from that to which the Feceiving antenna is connected, Consult the dealer or an experienced radia/TV technician for help, Hf these measures do not eliminate tha interference, please consul your dealer of an experienced radiqftelevision technician for additional suggestions. Also, the Federal Communications Commission has Prepared a helpful booklet, How To Identify and ResoWs Radio/TV Interlarence Problems, This booklet is avaiable Irom tha U.S. Goverment Printing Office, Washington, D.C. 20402. Please specify stock aumber 004-000-00345-4 when ordering Copies, Hearne Ai Comrarmiuiry This telephone system meats FCC standards for Hearing AML Compatibitty US NUMBER IS LOCATED ON THE CABINET BOTTOM REN NUMBER IS LOCATED ON THE CABINET BOTTOM 1 ATLINKS USA, Inc. trast a ae Base Handset AC power supp Mopvu1ark Jack REQUIREMED To properly connect your phone to your telephon type modular phone jack, which might look like t don't have a modular jack, call your focal phone one installed, DicrraL Securrry SysTEM Your cordless phone uses a digital security sy:

ringing, unauthorized access, and charges to When you place the handset in the base, the t power outage or battery replacement, you sho about 20 seconds to reset the code. WARNING: TO PREVENT FIRE OR. ELECTRICAL SHOCK HAZARD, DO NOT EXPOSETHIS PRODUCT TO RAIN OR MOISTURE. INSTALLATION AND SE INSTALLATION NOTE: Some cordless telephor interference to nearby TVs, microwave ovens, anc interference, the base of the cordless telephone st microwave oven, or VCR. If interference continue away from the TV or VCR will often reduce or elir. Certain other communications devices may als communication, and, if properly set, these dev or your new telephone. If you are concerned owner's manual for these devices on how to pr interference. Typical devices that may use the include wireless audio/video senders, wireless cordless telephone systems, and some long-rar IMPORTANT INSTALLATION Never install telephone wiring during a light:

Never touch uninsulated telephone wires or been disconnected at the network interface. Use caution when installing or modifying tel Never install telephone jacks in wet location designed for wet locations. DEskToP INSTALLATION wrong pag:

button loca 26928 InTRODUCTIO Your Cordless Telephone is designed to give you flexibility in use and high quality performance. To get the most from your new cordless telephone, we suggest that you take a few minutes right now to read through this instruction manual. IMPORTANT: Because cordless phones operate on electricity, you should have at Jeast one Phone in your home that is not cordless, in case the power in your home goes out. 40-Channel 900 MHz Cordless Telephone User's Guide CAUTION: When using telephone equipment, there are basic safety A instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. Brrore You BEGIN Parts CHECKLIST Make sure your package includes the items shown here. missing page button EQumrMENT APPROVAL INFORMATION Your tekephcaa aquipmant is approved lor connectva to the Publi Switched Telephone Network und ica comphanca with on and 68, FCG Palen and Regulations and the Tachnical Requiressents fer Telaghona Terminal Equipment published by Al 11 Netifection tthe Local Telephone Company othe bottom ofthis equipment is v label indicating, emcang ether information, the US nunber and Ringer Equivetance Murer (REN) for tha equipment, Yau ravst, upon request, provide this afermation to your tclephone corapary. Toa REN is useful detaining the numberof devices you mey connect to your wlephene ina and sil have all ofthese shaves ring hen your tlephona ruber seabed. br roost (but cto reas, he se of the REN of a davies connected t2 efi should aot xc 8, Tobe certain ofthe nude of civics you nay cones i yous fw determined by the REN, you shad contact your cal oephona company. Nos 1 Tai aqlpreest rary not be used on co service provid by the tephioms cxampams

* Party wre subject ost trfs, and therefore, you may nt be able ma use voor own telephone speed you ara on 1 party ine, Ceck with your local telephona compar.

+ Natce mustbe piv nthe telaphone company upon permanent disconnection of yout telephone fron yout Kaa, 2 Righesof he Teleptone Core i caubie on your fine which may harm the telephone notily yau that temasrary discontiruanes of service my may temporarily discantinus the telaghone company must:{1] promptly naify You of such temporary discantinuaai ity tw correct the situation: and {31 inform yau of Your right te bring a complaint to the Corunissica purrwant to procedures set forth in Subpart of Part 6, FCC Auda and Regulations, i Tha telephone cosipany may make changes in ite communications facies, equgmners. oparatisns oF procadurea whare such ction is raged in the operation ofits besiness and not inconsistent wih FCC Rakes and Regulation. hase changes are expected to affect the une of performance of your tlepona equipment, he ilephane corp muri gia you adequate sti, n lng awe ys o mats eintspied venice. :

INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Aulat, Operation ix subjact ta th folowing two conditions: {1} Ths davice may. nL cause harentud interte 14 {2} This device muct accept eny interference rs id, including interference that may cause undesires This equipment has buan tected and found to comply with the Nimitz for a Class & digital device, pursuant io Fart 5 of the FEC Aules. These fmits are designad to provide reasonable protection against harm intertaence in a installation, This oquipment geoarates, utes, and cas radinte radio frequancy energy and, # not instaied end used in accordance with the instrmctions, may cause harmtd interlersnce to radia communications. However, thara is 0 guarantee that intertarance will not occur i wicubar ir tian, ion, yerense the xeparation between the telecommvaications squiament and saceiviog

* Gannett teoorurcnos equipment io an oet on wero arnt hom ato which he ecekog aeons sonnecta Consult the dales or un experienced radio/TV technician tr hata, Htchesa masses donot eninata tha narfarence,plense consult your daaer ov an aperiancedraGiteevison trchniian for bekdincal suggestions, Alco, the Fader Communications Commission has prepared a help boollet. How To denidy and Rasobve ati/TV ltsterance Prablams, This booklet is availnbl tom the US, Government Prining Mie, Wostingtn, D.C, 20402. Please specify stock umber OH-00-00966-4 whan oedering copies, Hearinc Arp ComPatiBnity This tabephone nystum mats FCC standards tor Hearing Aig Compaubay. US NUMBEA IS LOCATED ON THE CABINET BOTTOM REN NUMBER IS LOCATED ON THE CASINET BOTTOM ATLINKS USA, Inc. 10336 North Meridian Street Indianapotis, IN 48290 2002 ATUNKS USA, Inc, Tratiemark|s) Registered Marcafs) Registrada(s}

Madel 26928 15880140 (Rev. 0 /S) 04-51 Printed in China Base Handset AC power supply Telephone line cord Moputar Jack REQUIREMENTS To property connect your phone to your telephone lines, you will need an RUT type modular phone jack, which might look like the one pictured here. if you dont have a modular jack, call your local phone company to find out how to get one installed, Dicrran Security SystEM Your cordless phone uses a digital security system to provide prataction against false Finging, unauthorized access, and charges to your phone line. When you place the handset in the base, the unit verifies its security code, After a power outage or battery replacement, you should place the handset in the base for about 20 seconds to reset the code. WARN#NG:7O PREVENT FRE'OR, ELECTRICAL SHOCK HAZARD, DO. NOY EXPOSE THIS PRODUCT TO RAIN OF MOISTURE. INSTALLATION AND SET Up INSTALLATION NOTE: Some cordless telephones operate al frequencies that may canse interference to nearby TVs, microwave ovens, and VCRs, To minimize or prevent such mterference, the base of the cordless telephone should not be placed near or on top of 2 TV, microwave oven, or VCR. ff interference continues, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. Certain other communications devices may also use the 900 MHz frequency for communication, and, if property set, these devices may interfere with each other and/

or your new telephone. Ifyou are concerned with interference, please refer to the owner's manual for these devices on how to properly set channels to avoid interference. Typical devices that may use the 0) MHz frequency for communication inchide wireless audio/video senders, wireless computer networks, muli-handset cordless telephone systems, and some long-range cordless telephone systems. Important INSTALLATION INFORMATION Never install telephone wiring during a lightning storm. Never touch uninsulated telephona wires or terminals, unless the telephone fine has deen disconnected at the network interface,

* Use caution when installing or modifying telephone fines.

* Never instail telephone jacks in wat locations unless the jack is specifically designed for wet locations. Desktop INSTALLATION wrong page button location 1, Remove the battery compartment door on the handset, insert the battery pack, plug the cord into the jack {inside the compartment}, and replace the compartment door, 2 Set the RINGER switch (on the handset front) to ON, and place handset in the cradle on the base. 3. Plug the power supply into the power jack on the back of base and the other end into an electrical outlet. The charge indicator comes on verifying the battery is charging, Allow the phone to charge for 12 hours prior to first use. If you don't Properly charge the phone, battery performance will be compromised, 4, Plug the telephon tine cord into the TEL LINE jack on the back of the base and into a modular phone jack, NOTE: The phone automatically defaults to touch-one dialing. To change to pulse

(rotary) dialing, see Tone/Pulse Dialing." Ifyou don't know which type of service you have, check with the phone company. CAUTION: Use only the ATLINKS USA, Inc. &XXXX (black) or SXXXX

(white) power supply that came with this unit. Using other adapters may damage the unit. Wai Mount INSTALLATION Because itis necessary to charge the handset for 12 hours prior to connecting the phone for use the first tims, itis better to leave the unit ona flat surface during initial charge before attempting to hang it on the wal. 1, Set the RINGER switch {on the handset front) to ON, and place handset in the cradle on the base, 2 Plug one end of the power supply into the power jack on the back of the basa and the other end into an electrical outlet. The riser indicator comes on, verifying the battery is charging, In use charge Altow the phone to charge for 1Z hours prior to first use. H yo don't property charge the phone, battery performance will be compromised, 4, Piug the telephone line cord inte the TEL LINE fack on the back of the base and into a modular phone jack. 4. Slip the mounting holes over the wall plate posts and slide the unit down firmly into place. (Wall plate not included.) 5, Place the handset in the cradle, NOTE: The phone automatically defaults to touch-tone dialing. To change to pulse

(rovary) dialing, see Tone /Pulse Dialing, I you dont know which type of service you have, check with the phone company. CAUTION: Use only the ATLINKS USA, fic, 5-XXXX (black) or 5XXKK

( white) power supply that came with this unit. Using other adapters may damage the unit. CorpiEss PHONE Basics VOLUME buitons TALK button program fhatydetere button redial/eathbwek button m Sema Bhtton TONE button channel/pregeem button FaSb ee button Finger switch Makinc A Cat After initial set up, put handset in the base for 12 hours to charge the battery. The only two things you need to know to make a call are:

* Press the TALK button before you dial.

* Press TALK or place the handset in the base to hang up. Use . In Tae uses cha rae se fy The phone is wt '@ lamp under the TALK button on the handset is fit REDIAL Prass the JALK button, than press the redial button to redial the last number you called

{up to 32 digits). If you get a busy signal, and want to keep dialing the number, just Press REDIAL again (you dont have to turn the phone off and back on}. RECEIVING A CALL To answer a call, you must press the TALK button before you can talk. FLasu Use the FLASH button to activate custom calling services such as Call Waiting or call transfer, which are available through your local phone company, TR: [f you press the TALK button to activate custom calling services such as call waiting, you'll hang up the phone. Press FLASH button instead. VOLUME The VOLUME (left and right arrow} buttons control the volume of the handset's earpiece. RINGER SwircH The handset ringer switch can be set to ON or OFF. Ifthe switch is off, the unit will not: ring. ToneE/PuLse DiaLinG This adjustment allows you to selact tone {touch-tane} or pulse {rotary} mode dialing. The phone is pre-set for touch-tone use. To set to tone or pulse dialing:

1, Press and hold the PROGRAM button for 2 seconds. You will hear a beep. 2 Press the TONE* button to select Tone Dialing or press PAUSE# to select Pulse Dialing, 3. Prass. the PROGRAM button again. You will hear a confirmation tone. 1, TEMPORARY TONE It you have pulse {ratary) service, and want to access customer calling services that Fequira tone dialing {such as telebanking and fong distance services}, you can use this feature to make your phone temporarily touch-tone compatible, 1, Press the TALK button. 2. Call the banks infarmation line. 3. Press the TONE button after your cail is answered. 4. Follow the voice instructions to complete your transaction. 5, Hang up when finished. The phone retums to pulse

{rotary} service. wrong location for page button Pacinc THe HaNnpsET Press the PAGE button on the base to locate a misplaced handset. When you press the PAGE button, the handset beeps and the indicator on the handset and the page/in use indicator on the base blinks, Press the TALK button when you jocate the handset, The page signal is three beeps every two seconds for two minutes, NOTE: You can still page the handsct with the ringer off CHANNEL Butron if you ever experience any interference or don't have clear voice quality, press the CHANNEL button on the handset to advance to another channel. Memory 0 Store up to ten 20-digit telephone numbers in memory for quick dialing. Storinc A NUMBER IN MEMORY 1. Make sure the phone is OFF. 2. Press the MEMORY button. 3. Press a number key (0-9} to store the phone number in that memory location. 4, Press MEMORY button. 5, Use the keypad to enter the number {up to 20 digits} you want to store in that memory location. 6. Press the MEMORY button again to confirm. CHANGING A STORED NUMBER Use the same procedure to change 2 stared number as you do to store a number you're just replacing the phone number with a different number. Sterne + Repms Never 1, dteleerserethespeents GF 2 Breet MEMOR bettors 9, Bresearrembertey-edhtestere-tiesprevenemberintnrbremeny frretien 4, Sree REBhite 5, Presentire MENT PM Strettenrererinteeerertrrrt:

STORING A PAUSE IN MEMORY Use the PAUSE # button to insert a pause when a delay is needed in the dialing sequence {for example, when you must dial a 9 to get an outside fine or when you must enter codes to access your banks information line). Each pause counts toward the 20-

digit limit, If you need to dial 9 to get an outside line and wantto store a number in memory without having to dial $ each time, you would:

1. Make sure the phone is OFF. 2. Press the MEMORY button. 3. Press a number (0-9) to store the phone number in that memary location. 4, Press MEMORY again. 5, Enter the number 9 {or any other appropriate number] to access an outside line. 6. Press PAUSE # button. 7. Enter the phone number you want to store in memary. 4. Press the MEMORY button again te confirm. TIP: If you need a longer pause, press the PAUSE # button wi Dratinc A STORED NUMBER 1. Make sure the phone is ON by pressing the TALK button. 2. Press the MEMORY button, 2. Press the number (0-9) for the desired memory location, The number dials autamaticalty. IMPORTANT: Ifyou make test cals to emergency numobers stored in memory, remain on the line and briefly explain the reason for the call to the dispatcher, Also it's good idea to make these calls in off-peak hours, such as early morning or late evening. CHANGING THE BATTERY Make sure the telephone is OFF before you replace battery. 1, Remove the battery compartment door. 2. Disconnect the cord attached to the battery pack and remove the battery pack from the handset. 3. Insert the new battery pack and cannect the cord into the jack inside the handset 4, Put the battery compartment door back on.

, Place handset in the base to charge. Hf yor don't charge the handset battery properly (for t2 hours) when you first set op tha phone and/or when you install a new battery pack, the battery's long-term performance will be compromised, only the battery listed in the instruction book. Barrery SAFETY PRECAUTIONS

* Do not burn, disassemble, mutilate, or puncture. Like ather batteries of this type, toxic materials could be released which can cause injury. To reduce the risk of fire or personal injury, use only the battery listed in the User's Guide.

* Keep batteries out of the reach of children. Remove batteries if storing over 30 days. HanpseT SouND SIGNALS Signal Meaning You have an incoming call (with ringer ON) The handset is being paged Along warbling tone Three long beeps Four short beep Low battery waming every 7 seconds Lamp UNDER TaLk BUTTON Signal Meaning Lights steadily Phone is in use Quickly flashing You have an incoming call or page Flashes every 7 seconds Low battery warning TROUBLESHOOTING GUIDE In case of difficulty, please check the following Troubleshooting Guide before seeking service. Problem No dial tone Solution

* Check installation:

ls the base power cord connected to a working outlet?

- Ara the inuse amps on the handset and base lit? in use/charge Isthe handset rBenp Tie?

Is the telephona line cord connected to the base unit and the wall jack?

Disconnect tha base from the wall jack and connect another phone to the same jack. If there is no dial tone in the second phone, the problem might be your wiring or local service. fs the handset out of the base unit's range? Move closer to the base unit, Make sure the battery is property charged

{12 hours}. Is the battery pack instalfed correctly?

* Ifthe phone still does not work, discon nect the power cord and remove the battery pack. Then reconnect the it cord and reinstall the battery pack. Place handset in the base for 10 seconds to allow it to reinitialize, Dial tons is OK, but can't dial out Make sure the tone/pulse setting is programmed correctly. Make sure the RINGER switch on the handset is turned to ON, You may have too many extension phones on your line, Try unplugging some phones,

* See solutions for No dial tone?

Handset does not ring Press the VOLUME (left and right arrow}

buttons to adjust the volume to the desired listening level. Cannot hear phone conversation You experience static, * Change channels. noise, or fading in and out Is handset out of range? Move closer to the base,

* Does the base need to be relocated?

* Charge handset battery.

* Make sure base is not plugged into an outtet with another household appliance.

* Press the CHANNEL button during the Range is shorter conversation to select a new channel, than normal Battery will not hold a Be sure you are sufficiently charging the charge battery for 12 hours, you can expect approximately 4 hours of talk time.

* Check to be sure battery contacts on both the handset and the base are makin:

contact and are clean; free of dirt or lint. When the handset is placed in the base, check that the base lamp is on. in use/ charge

* Did you program the memary location keys correctly?

* Did you follow proper dialing sequence?

* Make sure the tone/pulse setting is programmed correctly. Memory Dialing doesn't work tf the phone still does not work, disconnect the power cord and remove the battery pack. Then reconnect ths power cord and reinstall the battery pack. Place handset in the base for 10 seconds to allow it to reinitialize. Ifa power outage occurs while the handset is away from the base, the handset must be returned to the base when the power returns, Unit locks up and no communication between the base and the handset Limrrep WARRANTY ST What your warranty covers:

Defacts in materials or workmanship. For how long after your purchase:

* One yoar, from date of purchase.

(The warranty periad for rental units bogins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first}

What we will da:

+ Provide you with a naw of, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product's warranty period. How you get service:

+ Property pack your unt. Include any cables, etc., which were originally provided with the product We recommend using the original carton and packing materials.

+ Proof of purchase in the form af a bil of sale or receipted invoice which is evidence that the productis within the warranty period, must be presented ta obtain werranty service. Far rental firms, proof of first rental is also required. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, ine. c/oThomson muttimedia Inc. 11721 B Alameda Ava. Socorro, Texas 79927

+ Pay any charges biled to you by the Exchange Center for service not covered by the warrenty. Jnsure your shipment for loss or damage. Atinks accepts no liability in case of damage or loss.

= Anewor refurbished unit will be shipped ta you freight prapaid. What your warranty does not cover:

Customer instruction. fYour Gwmers Manual provides information regarding operating instructions snd user controls, Any additional information, should be obtained fram your dealer.) Installation and setup service adjustments. Batteries, Damage from misuse or neglect. Products which have been modified or incorporates into other products. Products purchased or sarviced outside the USA. Acts of nature, such as but not fimited ta lightning damage. Product Reglstration:

4 complete and mail the Product Registration Card packed with your wnt. twill make it sler to contact you should it ever be necussary. The return of tha card is not requirad for warranty coverage. Limitation of Warranty:

+ THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED {INCLUDING ALL IMPLIED WARRANTIES GF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE} ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC, 11S AGENTS, OR EMprovees SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS ry.

+ REPAIR DR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ATUINKS USA, INC. SHALL NOT BE LIABLE FOR INCIOENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODLICT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR iMPLIED WARRANTY ON THIS PRODUCT. THIS CISCLAIMER GE WARRANTIES AND LIMITED WAARANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED SY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. How state law relates to this warranty:

Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts so the above limitations or exclusions may nat apply to you.

+ This warranty gives you specific legal rights, and you also may have other rights that vary from state te state. If you purchased your product outside tha USA:

This warranty does not apply. Cantact your dealer for warranty information. SERVICE Se This product may be serviced only by the manufacturer or its authorized service agents, Changes of modifications not expressly approved by ATLINKS USA, Inc. could void the user's authority to operate this product For instructions on how to obtain service, refer ta the warranty included in this guide or call customer service at 1-800-

448-0329, ~

Or refer inquiries to:

ATLINKS USA, Inc. Manager, Consumer Relations PO Box 1976 Indianapolis, IN 46206 Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift. This information will be valuable if service should be required during the warranty period. Purchasedate Name of store pron nn Accessory ORDER FORM Ce

[_pesceiprion

CUSTOMER: CUT ALONG DOTTED LINE, Ss ee ei ee ee eT

[Rererame _| * |

[encore tate |__|

To order, call 1-800-338-0376 (for accessorias only) or complete this order form. For credit card purchases Your complete charge card number, its expiration data and your signature ara necassary to process afi charge card orders. Copy your complete account number from your VISA card. LIT OOOO OLLI My card expires:

(TTT) Copy your complete account number fram your Master Card of Diseover. LOU TOTO Copy the number above your name on the Master Card, LO My card expires:

CTT) Authorized Signature Prices are subject to change withaet notice. Total Merchandise. Sales Tax.. Yiu are required ry law te coiect the eppronriate sales (ax fer cack individwol stste, County, smd ical te which te merchandice i blag S08, Use VISA or Master Card or Discover preferably. Meney ander of check mest be Ta U.S. coreecy only. Na COD of Cash. All accessaries Bre: sallect -avuilability. Where plicable, we will ship a superceding evodel, Shipping/Handiing.... $95.00 Total Amount Enciesed..... S__. Mail ordar form and money order or check {in U.S. currency) mada payable to Thomsan muttimedia Inc. 10:

Thomson multinredia ine. Mail Order Department PO. Box 9419 Ronks, PA 175738413 Name, Address, City Daytime Phase Numbert ) Please make sure that this form has been filled out completely. Apt, State, ZIP.