FCC ID: 2BC92-TIMEB-MINI Mini

PMN:Mini OS5 Last updated March 2024 Thank You for purchasing the Timebirds mini workout timer. Upon receipt of the pro-

duct, check for any defects prior to first use. If defects are found, do not use and contact Timebirds immediately.

It is Safety important to read and understand all instructions before using Ti-

mebirds. Only use Timebirds mini as des-

cribed in the manual. Warning | Overheating, damage or exposu-

re to excessive heat may cause the battery to explode and cause flames resulting in physical harm. Always use a compatible charging de-

vice when charging. Do not overload wall out-

lets, extension cords, or adaptors beyond their capacity. Do not place the device in a fire or near extreme heat. Stop using the device if the battery is damaged or malfunctioning. Do not attempt to repair the battery. Always recycle, or dispose, of the battery according to your local environment laws and guidelines. Poorly struc-

tured, or executed, workouts may cause perso-

nal injury. Proper setup and use of this device is the responsibility of the user. Timebirds bears no liability beyond the replacement value of the device. Notice | Timebirds mini is not waterproof and may become damaged if exposed to water. Always place Timebirds mini in a dry area. Dropping, throwing or bumping the device may cause damage to the device. Do not use Time-

birds mini as a toy or let children use the de-

vice without proper supervision or instruction. Product Care | Always store Timebirds mini in a clean and dry environment. To clean, wipe with a damp cloth, do not use harsh che-

micals or cleaning agents. Do not dissembled, try to repair or modify. The lens is designed to pop in and out. In the event of the lens popping out, simply pop it back in so the Timebirds mini logo car be read while facing you. Specifications Weight: approximatively 150gr. Maximum volume: of the Piezo is 75db. Battery type: Lithium-Ion Polymer Capacity: 1200 mAh - 3.7V Operating Temp: 10 40 degrees Celsius / 50 104 degrees Fahrenheit Dimensions: 155mm (length) x 22mm (width) x 47mm (height) Warranty | Timebirds mini is covered by a 12-month limited warranty for manufacturers defects and faults. The warranty does not cover normal wear and tear or cosmetic damage. The warranty does not cover negligent or improper use, alteration, mishandling, self-repair, poor maintenance, water damage or incorrect sto-

rage. For more information about Timebirds warranty, visit www.timebirds.com Customer Service | For more information, troubleshooting, warranty, and replacement information please visit www.timebirds.com. Please contact us for return addresses and replacements before returning your product. 2 3 1. Whats in the box?

1x Timer 1x USB to USB-C charging cable Power 1 2 3 4 5 1. On/Off 2. Cycle modes 3. Decrease value 4. Increase value 5. Accept/advance 6. USB-C port Hold 2s to turn Timebirds on or off Press once to display battery level feedback (%). Mode Press to cycle through the mode Hold 2s to go back to the home screen 6 Decrement Press decrement value Increment Press to increment value Set HOME SCREEN Press to validate your entry Hold 3s to enable Bluetooth discovery mode. IN A MODE Press to stop the timer Press again to restart Hold for 2s to reset the timer 4 5 2. Screens General Screens Off Home screen Low battery warning Battery charge 100%

Battery % charged Count up mode Count down mode Interval training mode Tabata mode Fight gone bad mode Beep Test. Heat mode Clock mode Rep counter mode Settings Clock setting Sound setting Timebirds workout memory setting Timebirds OS version intro sound enabled Intro sound disabled Count down to start disabled Count down to start enabled Stopwatch Timebirds pairing activated Sound Level Screens Sound off Sound level 1 Sound level 2 Sound level 3 Clock Screens AM time PM time 12 hours clock format 24 hours clock format Workout Memory Reset last workout setting Save last workout setting Mode Setting Screens Counting up Counting down Set a working time Set a test time Set number of rounds Counting up

(Interval training mode only) Count down

(Interval training mode only) 6 7 3. Audio Indications Long beep Normal beep Short beep Mode is set and ready to go Count down to start

(3, 2, 1) Transition from one Round to the next Transition from a rest To a work period Transtion from a work to rest period Start of a workout Transition from a rest to work period. End of a workout 4. Operating Timebirds mini Charging Timebirds mini Using the provided USB to USB-C Cable, plug USB-C connector into Timebirds mini Plug in USB port to any DC power adapter Timebirds mini will display the current level of charge and beep twice to indicate power is being sent to the device indicates full charge NOTE:

Timebirds mini can also operate when plugged in Battery Level Feedback Press to display the level of battery left indicates battery level <10%

NOTE:

The function works even when Timebirds is turned off. General Overview Hold Press Press Press Press for 2s to power on/off to cycle modes to accept and advance to decrease time to add time NOTE:

In home screen will turn itself off after 30s of inactivity Timebirds mini 8 9 When a timer is running How to display the Clock Press Press Hold once to pause once to start for 2s to restart your workout Press Press Hold to cycle modes until to accept and display clock for 2s to return to home screen When setting up a mode How to set the Clock to add or decrease time Flashing digit represent number being adjusted Press Press Press Hold or to accept and advance and 2s any time to return to home screen to go back Adjust Volume Press Press Press Or, simply press timer is running to cycle modes until to accept and display settings to cycle settings until or at any time when NOTE: Timebirds mini has 3 volume levels

(3 being the loudest) and an off position. Adjust Brightness Press or at home screen NOTE: Timebirds mini has 4 levels of dimming, 4 being the brightest. By default, Timebirds mini is set at Level 4. Battery life may vary based on brightness setting. to adjust the GREEN flashing to cycle modes until to accept and display settings cycle settings until to accept and advance or Press Press Press Press Press digits for a 12 or 24 hour format to accept and advance Press Press or digits corresponding to hours Press Press digits corresponding to Minutes Press to accept and advance or to accept and advance to adjust the pair RED flashing to adjust the pair RED flashing NOTE: Timebirds mini will autmatically synchronize to your local time zone once paired with your device. How to disable/enable the count down to start Under the home Screen Hold start. Hold start. for 2s to disable the count downto for 2s to enable the count down to 10 11 How to save your workout How to start a Count Up By Rounds (ie EMOM or For Time) to cycle modes until to accept and display settings to cycle settings until to accept and advance or Press Press Press Press Press disable settings after your Timebirds is turned off Press to accept and advance to the home screen to enable the memory of your last or NOTE: Individual mode memory setting will retain settings even if the battery dies. Settings (memory) are only saved after the device is turned off using the button or idle timeout. to adjust the flashing digit to cycle modes until to accept and advance or Press Press Press

(time) Press Repeat the above 2 steps until Press

(number of rounds) Press Press to accept and advance to start or to accept and advance to the next to adjust the flashing digits NOTE: If you leave all digits to 0, Timebirds mini will count up until 99:59 Minutes:Seconds How to Pair my Timebirds ?

How to start a Count Down On your mobile device, go to Settings >

Bluetooth and turn on Bluetooth. Stay on this screen until you complete the steps to pair your accessory. To place your Timebirds mini in discovery mode, hold the button for 3s and wait for to appear on your device. To pair, tap your accessory name when it appears onscreen NOTE: The Timebirds control app can be found on Android and Apple AppStore to adjust flashing digit (time) to cycle modes until to accept and advance or to accept and advance Press Press Press Press Repeat above 2 steps until Press

(number of rounds) Press Press to accept and advance to start or to adjust flashing digits How to turn off/on the intro Beep Under the home Screen Press Press to turn off the beep to turn on the beep NOTE: The volume is synchronizied with the sound level setting. 12 13 How to start a Custom Interval Training (ie Tabata) How to start a Custom Interval Training (ie Tabata) to adjust flashing digit to cycle modes until to accept and advance or Press Press Press

(time on) to accept and advance Press Repeat the above 2 steps until Press or

(period of rest) Press Repeat above 2 steps until Press

(number of rounds) Press Press to accept and advance to start workout to accept and advance or to adjust the flashing digits to adjust the flashing digits How to use the Rep Counter mode. to cycle modes until to accept and advance. Press Press in the mode, press Press Hold Hold to decrease count. for 2s to reset. for 2s to return to home screen.

, to increase count. NOTE : 1 heat consists of 1 cycle, which includes a period of work followed by a period of rest. If you set 3 heats, you will need to choose both the duration of work and rest for each of the 3 heats individually. The maximum number of custom cycles, or heats, is 30. Press the decrement button to cycle modes until Press or forward to accept and advance Use the key pad or press the increment or decrement button to adjust the flashing digit

(number of heats). Press Using the key pad :

or forward to accept and advance select the period of work for HEAT select the period of rest for HEAT 1 select the period of work for HEAT select the period of rest for HEAT 2 etc. Repeat for each heat. Once all heats are set up, Press to start. or forward Firmware updates visit www.timebirds.com How to Reboot my Timebirds?

Hold factory settings for 2s to reboot/reset to 14 15 FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ISED Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1)

(2) the device. This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1)

(2) en compromettre le fonctionnement. L' appareil ne doit pas produire de brouillage;

L' appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'

ISED Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used installed and operated with minimum distance 0mm between the radiator and your body. L'appareil a t valu pour rpondre aux exigences gnrales d'exposition aux RF.Cet quipement doit tre install et utilis avec une distance minimale de 0 mm entre le radiateur et votre corps.

@timebirdstimers

@timebirds

@timebirds 2024 Timebirds Australia Pty Ltd, All rights reserved. Timebirds OS-5. Timebirds and Timebirds logo are Trademarks of Timebirds Pty Ltd registered in Australia and other countries. 16

Page 1 of 1 FCC ID: 2BC92-TIMEB-MINI LABEL AND LOCATION Mini Model: TIMEB-MINI FCC ID: 2BC92-TIMEB-MINI

(Size: L4.0cm x 3.0cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Timebirds Australia Pty Ltd 36-38 Gipps Street Collingwood, Victoria 3066 Australia Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

2024-4-12 We, Timebirds Australia Pty Ltd, hereby certify that the equipment for which authorization is sought

(FCC ID: 2BC92-TIMEB-MINI) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, 3 0 V

, U

) i i

d n a

) i

) 5

) d

1 1 9 2 _ u q E d e r e v o C

l e d o m

_ 2 6 Signature Julien Claudin Director Timebirds Australia Pty Ltd

Timebirds Australia Pty Ltd Add: 36-38 Gipps Street Collingwood, Victoria 3066 Australia Date: 2024-4-12 FCC ID: 2BC92-TIMEB-MINI Dear Sir/Madam, We, Timebirds Australia Pty Ltd Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: Mini Model no.: TIMEB-MINI, TIMEB-MINI V1.0 Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Julien Claudin/Director Timebirds Australia Pty Ltd 36-38 Gipps Street Collingwood, Victoria 3066 Australia

+61408636627

+61408636627 julien@timebirds.com

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-4-12>

Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 2BC92-TIMEB-MINI Model name TIMEB-MINI For the product stated above, we request that the following information be held confidential;

Exhibits Long-Term Short-Term Short-Term Confidentiality Confidentiality Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Julien Claudin/Director Timebirds Australia Pty Ltd 36-38 Gipps Street Collingwood, Victoria 3066 Australia

+61408636627

+61408636627 julien@timebirds.com

Timebirds Australia Pty Ltd 36-38 Gipps Street Collingwood, Victoria 3066 Australia Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

2024-4-12 We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BC92-TIMEB-MINI including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Julien Claudin/Director Timebirds Australia Pty Ltd 36-38 Gipps Street Collingwood, Victoria 3066 Australia

+61408636627

+61408636627 julien@timebirds.com

Timebirds Australia Pty Ltd 36-38 Gipps Street Collingwood, Victoria 3066 Australia Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-4-12 U.S. Agent Designation Timebirds Australia Pty Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought

(FCC ID: 2892-TIMEB-MIN}):

Name and company of U.S. agent: REP America LLC Physical U.S. address of agent 1942 Broadway St. STE 314C, Boulder, CO 80302 United States FRN of US. agent: 0034192500 Email address of U.S. agent: dzeng@rep-europe.de REP America LLC acknowledges their obligation to accept service of process on behalf of Time Pty Ltd. Timebirds Australia Pty Ltd with the FRN [0034380790] accepts its obligation to maintain an agent for service of process in the United States for no less than one year afer either the grantee has permanently terminated all marketing and importation ofthe applicable equipment within the U.S.. or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(4\7) The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 Dot An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Signature Julien Claudin Ben Xu Director Manager Timebirds Australia Pty Ltd REP America LLC