FCC ID: RPOA100WIRF Megapixel Wireless Day & Night Network Camera

A100WIRF Series Megapixel Wireless Cube Day/Night Network Camera User Manual A.3 NOTICE Please read this manual thoroughly and save it for future use before attempting to connect or operate this unit. 1 A100WIRF SeriesUser Manual Table of Content WARNING ......................................................................................................................................................... 3 FCC Compliance Statement ............................................................................................................................ 4 CE Statement .................................................................................................................................................... 4 Preface .............................................................................................................................................................. 5 1. Product Overview ........................................................................................................................................ 6 1.1 Physical Characteristics .................................................................................................................. 6 2. Installation and Connection ........................................................................................................................ 8 2.1 Unpack Everything............................................................................................................................ 8 2.2 Installation ......................................................................................................................................... 8 2.2.1 Checking Appearance ............................................................................................................. 8 2.2.2 Connecting the wires ............................................................................................................... 8 2.2.3 Mounting .................................................................................................................................. 9 2.2.4 Network Topology ................................................................................................................... 11 2.3 Connection ...................................................................................................................................... 12 2.3.1 System Requirements ........................................................................................................... 12 2.3.2 Connecting from a computer ................................................................................................. 13 2.3.3 Default IP address ................................................................................................................. 14 2.3.4 Internet options setting from PC ............................................................................................ 14 2.3.5 IP finder ................................................................................................................................. 16 2.3.6 Verify connection between PC and IP Camera ..................................................................... 17 2.3.7 Viewing Preparation .............................................................................................................. 17 2.3.8 Login Window ........................................................................................................................ 20 3. Administration and Configuration ........................................................................................................... 21 3.1 Live View .......................................................................................................................................... 21 3.2 Configuration................................................................................................................................... 23 3.2.1 Image Parameters ................................................................................................................. 23 3.2.2 Event Settings ....................................................................................................................... 35 3.2.3 Network Settings ................................................................................................................... 38 3.2.4 WIFI Settings ......................................................................................................................... 41 3.2.5 Account .................................................................................................................................. 45 3.2.6 System .................................................................................................................................. 47 3.2.7 Event Log .............................................................................................................................. 50 3.2.8 Client ..................................................................................................................................... 50 3.2.9 Information ............................................................................................................................ 51 Appendix: Specification of A100WIRF Series ............................................................................................. 52 2 WARNING This unit operates at DC 5V. Installation and service should be performed only by qualified and experienced technicians and comply with all local codes and rules to maintain your warranty. To reduce the risk of fire or electric shock, do not expose the product to rain or moisture. Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry soft cloth. Do not apply benzene or thinner to the camera, which may cause the surface of the unit to be melted or lens to be fogged. Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time. Avoid operating or storing the unit in the following locations:

Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -10C to

+40C) Close to sources of powerful radio or TV transmitters Close to fluorescent lamps or objects with reflections Under unstable or flickering light sources WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product

(applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures. 3 A100WIRF SeriesUser Manual FCC Compliance Statement This equipment has been tested and found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

-- Consult the dealer or an experienced radio/TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the p arty responsible for compliance could void the user's authority to operate the equipment. receiver is connected. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 4 CE Statement Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer declares that the unit supplied with this guide is compliant with the essential protection requirements of EMC directive and General Product Safety Directive GPSD conforming to requirements of standards EN55022 for emission, EN 55024 for immunity, EN 300 and EN 328 for WIFI. Preface This user manual is designed as a reference for the installation and manipulations of the unit including the cameras features, functions, and detailed explanation of the menu tree. The reader is supposed to be able to get following information in the manual. Product Overview: the main functions and system requirements of the unit. Installation and Connection: instructions on unit installation and wire connections. Administration and Configuration: the main menu navigation and controls explanations. 5 A100WIRF SeriesUser Manual 1. Product Overview 1.1 Physical Characteristics FIGURE 1-1: PHYSICAL DIMENSION A Unit: mm Unit: mm FIGURE 1-2: PHYSICAL DIMENSION B & PICTORIAL INDEX*

*Refer to table 1-1 for definitions 6 Index #

1 2 3 4 5 6 7 8 9 10 11 Name WIFI antenna MIC Infrared LED*

Lens Speaker Default Button Reset Button RJ-45 Ethernet Connector Power Terminal Unit stand LED Indicator TABLE 1-1: PICTORIAL INDEX DEFINITION Description Sending/receiving radio signals from computers or other WIFI facilities for wireless communication Audio IN Illumination for night vision Fixed lens Audio OUT (Optional) Resetting the unit to factory default (press and hold for 5 seconds) This button also has WPS function. Please press this button around 2 sec then WPS will be connecting. Rebooting the system. Wired network connection socket Inlet for the power adaptor (DC 5V10%, 1.5A) The units body support Red Light On Wired Network Ready With Networking Red Light Blinks Wired Network Ready Without Networking Wireless Network Ready With Networking and AP connection Blue Light On When ad hoc of WIFI mode is enabled and networking, the blue light will turn on. WPS ready and connection Wireless Network Ready Without Networking and AP connection WPS ready without networking Blue Light Blinks Blue Light Blinks Rapid

* D/N mode setting is auto. Cube network camera with IR ON will automatically switch to B/W mode when the illumination is under a certain threshold. Note Once wired networking is unavailable, please press and hold the default Button for 5 seconds to restore the unit to factory default settings so you may reach the unit at its default IP address for good. Please use IP finder utility to find the IP address again. If you want to use wireless network, you can press and hold Default (WPS) button a few seconds to connect the network. The LED status will turn blue after WPS successful connection. Otherwise, the blue light will always blink rapid. When WPS cant success connection, please repeat the operation. 7 A100WIRF SeriesUser Manual 2. Installation and Connection 2.1 Unpack Everything Check everything in the packing box matches to the order form and the packing slip. In addition to this manual, items below are included in the packing box. One unit of Megapixel Wireless Cube Day/Night Network camera One set of WIFI antenna & unit stand Four TP415mm tapping screws Four screw anchors One CD containing the IP Finder, user manual and quick installation guide One mounting template One power adaptor One printed quick installation guide Please contact your dealer if any item missing. 2.2 Installation Following tools might help you complete the installation:

a drill screwdrivers wire cutters 2.2.1 Checking Appearance When first unboxing, please check whether if there is any visible damage to appearance of the unit and its accessories. The protective materials used for the packaging should be able to protect the unit from most of accidents during transportation. Please remove the protective part of the unit when every item is checked in accordance with the list in 2.1 Unpacking Everything. 2.2.2 Connecting the wires Connect the DC 5V power adaptor to camera. Connect the network cable to the RJ-45 terminal of a switch. 8 2.2.3 Mounting The WIFI antenna and the unit stand are the necessity to mount a complete unit. 1. WIFI antenna 2. Cameras body 3. Unit stand FIGURE 2-1: ACCESSORY ASSEMBLY EXPLODED VIEW This unit has two ways to mount. You can attach the stand to one of holes at either end, one is at the back of the unit; the other, bottom, of the unit as the following figures. FIGURE 2-2: ACCESSORY ASSEMBLY SIDE VIEW Unit: mm 9 A100WIRF SeriesUser Manual After the unit assembled, mount the unit to the ceiling or wall by steps below. 1. Attach the mounting template to the ceiling or wall. 2. Drill four holes, and then insert the screw anchors into the holes. 3. Secure the bottom case of the unit to the ceiling or wall with the TP415mm tapping screws. Note Depending on the material of your mounting surface, you may require different screws and anchors than those supplied. 1 Screw anchors(4) 2 TP415 tapping screws(4) FIGURE 2-3: MOUNTING DIAGRAM 10 2.2.4 Network Topology The camera can deliver video images and audio in real time using the Internet and Intranet. It's equipped with Ethernet RJ-45 network interface. FIGURE 2-4: NETWORK TOPOLOGY Figure 2-4 illustrates how the A100WIRF unit routes packet through the internetworking. With proper settings, users are able to manipulate the A100WIRF unit from both inside and outside of the administrative domain. 11 A100WIRF SeriesUser Manual 2.3 Connection 2.3.1 System Requirements Below table lists the minimum requirement to implement and operate A100WIRF unit. No hardware/software component underestimated is recommended. TABLE 2-1: SYSTEM REQUIREMENTS Intel Pentium 4 2.4GHz or equivalent 1 GB NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500 (DirectX 9 compatible) System Hardware CPU RAM Display System Software Operating System Microsoft Windows XP, Windows Vista, or Windows 7 Browser Unit Power Supply Networking Wired Wireless*

Microsoft Internet Explorer 8 or above DC 5V 10/100BASE-T Ethernet (RJ-45 connector) Wi-Fi wireless networking (based on IEEE 802.11n specification); IEEE 802.11 b/g/n compatible

*Effective wireless connection speed varies from environments and distances between access points. Note All the installation and operations should comply with your local electricity safety rules. 12 2.3.2 Connecting from a computer There are two kinds of connection methods for your selection. One is wired connection and the other one is wireless connection. Way 1: Wired connection FIGURE 2-5: WIRED CONNECTING FROM A COMPUTER Note The status LED of camera will turn red when obtaining an IP address and the network connection is processing. Way 2: Wireless connection Press and hold the WPS button on your Camera for 2 seconds. The LED should blink blue light rapid. Within one minute, press the WPS button on your router. Note The status LED of camera will turn blue when obtaining an IP address and the network connection is processing. FIGURE 2-6: WIRELESS CONNECTING FROM A COMPUTER 13 A100WIRF SeriesUser Manual 2.3.3 Default IP address Since this is a network-based unit, the units default IP address was assigned by Router in DHCP server mode. Please enabled a DHCP server in your network, the unit would obtain an IP address automatically from the DHCP server so that you dont need to change the cameras IP address. 2.3.4 Internet options setting from PC Please open network connection status and then click Properties. FIGURE 2-7: INTERNET OPTIONS 1/3 Enable IPv4 in Internet options. FIGURE 2-8: INTERNET OPTIONS 2/3 14 Also, click Properties and set to obtain an IP address and DNS server address automatically. FIGURE 2-9: INTERNET OPTIONS 3/3 Before started Internet Explorer, please install IP finder.exe first and find the default IP address. For more information, please refer to IP finder description as follows. 15 A100WIRF SeriesUser Manual 2.3.5 IP finder IP Finder is a utility program that helps users to locate the unit in local area network that computer is connected to. Please note that IP Finder works only in Microsoft Windows XP, Microsoft Windows Vista, and Microsoft Windows 7. Steps to get the utility program running are listed below. 1. 2. Copy the IP Finders folder on the CD-ROM to computer. 3. Double click on IpFinder.exe in computers IP Finder folder, and the IP Finder window should pop out. 4. The window would list information of units in operation at present. Press FIND CAMERA to find more Insert the CD-ROM in the optical drive. units. 5. Locate and double-click the camera you want to configure the network settings. If you have multiple cameras connected to your local network, locate the MAC address on the camera to distinguish the target camera from others. 6. Configure the following settings as needed. Name: Enter a descriptive name for the camera. Network Setting: If you have a DHCP server on your network to assign IP addresses to network devices, enable the DHCP option. Otherwise, manually enter the IP, Subnet Mask and Gateway settings. FIGURE 2-10: IP CAMERA FINDER Click SETTING to enable the settings and click Exit to exit the utility. 16 2.3.6 Verify connection between PC and IP Camera Check whether if the networking available between the unit and the computer by executing ping the default IP address. To do this, simply start a command prompt (Windows: from the Start Menu, select Program. Then select Accessories and choose Command Prompt.) At the prompt window, type Ping x.x.x.x, where x.x.x.x is the IP address of the camera (the default address of IP camera is 192.168.x.x). If the message Reply from appears, it means the connection is available. 2.3.7 Viewing Preparation Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these steps to enable the display. 1. Enable Cookies as instructions below On the Privacy tab, move the settings slider to Low or Accept All Cookies. Click OK. 2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select In Internet Explorer, click Internet Options on the Tools menu. Connect tab, click LAN button, and set proxy server. If the camera operates inside of the intranet, click the Intranet icon. If the camera operates outside of the intranet, click the Internet icon. 3. Change Security in Internet options as instructions below. On tool menu, click Internet Option. Press the Security tab. Click Custom Level. This will open the Security Settings Internet Zone screen. FIGURE 2-11: SECURITY SETTINGS 1/4 17 A100WIRF SeriesUser Manual Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:

Download signed ActiveX controls Prompt (recommended) Download unsigned ActiveX controls Prompt Initialize and script ActiveX not marked as safe for scripting Prompt FIGURE 2-12: SECURITY SETTINGS 2/4 Automatic prompting for ActiveX controls Enable FIGURE 2-13: SECURITY SETTINGS 3/4 18 Run ActiveX controls and plug-ins Enable Script ActiveX controls marked safe for scripting* Enable FIGURE 2-14: SECURITY SETTINGS 4/4 Press OK to save the settings. Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect. 19 A100WIRF SeriesUser Manual 2.3.8 Login Window 1. Type your setting IP address into the browser. 2. Or, double click IP address in IP Finder window then a login window should pop up. FIGURE 2-15: LOGIN WINDOW 1/2 In the window, please enter the default user name: admin and set password/password (confirm) to login window. If you are the first time to login window, you can set a favorite password then Save it. The password will be memorized on the system. Please dont forget the password when you login IP website again. FIGURE 2-16: LOGIN WINDOW 2/2 3. 4. Further administration information on the unit can be found in User manual 3. Administration and If user name and password are correct, you should be able to see the camera image screen. Configuration. 20 3. Administration and Configuration 3.1 Live View Live view is the default page to open when accessing the units IP address. Live video is displayed directly in the browser window. Followings are explanations to the tab on the left of the window. Subtitle Display: to display information of the unit and the stream on the screen. SnapShot*: to take a picture from live view. *Storage folder of the pictures taken can be assigned by clicking the icon right next to the SnapShot. Audio In: MIC. Please enable this function and refer to 3.2.6.1 Audio setting for more information. Size 1:1: to set the display screen to 1:1 or fix full screen. Stream 1/Stream 2/Stream 3: The unit offers a concurrent triple streams for optimized quality and bandwidth with codecs available in H.264 or M-JPEG.

/

: This icon indicates to stop or start recording by manual.

: This icon indicates a motion event detected. When turned on and triggered, the alarm message will be displayed on the screen. After clicked this icon, the alarm message will be disappeared. Please refer to 3.2.2 Event Settings for more information. Recording message: Please click this icon to store image into a specific folder.

: This icon indicates to record image by manual. When started it, the recording message will be displayed on the screen.

: This icon indicates to record a motion event into a specific folder. When turned on and triggered, this icon will be displayed and disappeared on the screen after 20 sec if no any motion event. Please refer to 3.2.8 Client-recording setting for more information.

: This icon indicates to record a schedule event into a specific folder. When turned on and triggered, this icon will be displayed on the screen. Please refer to 3.2.8 Client-recording setting for more information.

: This icon indicates to show the folder files. Save the recording file: The storage path is same as snapshot. The default path is C:\Documents and Settings\username\Local Settings\Temp\NetworkCamera\... Or the end user can select a specific folder to save the image. Recording file format: Avi. The end user can be used VLC or Windows media player to display the file. Caution 21 A100WIRF SeriesUser Manual FIGURE 3-1: LIVE VIEW On the top right corner, you should notice User: Administrator/log out. Click log out and you will back to the logging window. 22 3.2 Configuration When clicking Configuration, a window will be popped out for configuring Image Parameters, Event Settings, Network Settings, WIFI settings, Account, System, Event Log, and Information. 3.2.1 Image Parameters FIGURE 3-2: CONFIGURATION FIGURE 3-3: IMAGE PARAMETER 23 3.2.1.1 Basic Settings-Exposure A100WIRF SeriesUser Manual Automatic Exposure FIGURE 3-4: BASIC SETTINGS EXPOSURE FIGURE 3-5: AUTOMATIC EXPOSURE SETTING Automatic Exposure controls the light intensity of picture. Users can select Manual or AES (Automatic Electronic Shutter) for the unit depending on applications. When chosen the Manual, Shutter Speed and Manual Gain can be adjusted. Day-Night To set DAY/NIGHT function, simply move the cursor to select Auto, Color, or BW mode. If Color selected, the unit is forced to stay in COLOR mode all day. If BW selected, the unit is forced to stay in black/white mode all day. FIGURE 3-6: DAY-NIGHT SETTING Shutter Speed*

*Only when Automatic Exposure set to Manual can Shutter Speed be adjusted. FIGURE 3-7: SHUTTER SPEED SETTING Set desired Shutter Speed from 1/60(1/50)s to 1/8000s. The unit will adjust the shutter speed according to the amount of outside light. Selecting 1/8000s provides the dark image. 24 Slow Shutter Slow Shutter can be enabled if the sensitivity is still not good enough under High gain condition at dark. Optimal image level can be maintained by appropriate gain and shutter combination that determined automatically inside the unit system. Slow Shutter can be selected from OFF, 1/30, 1/15, and 1/7.5. As slow shutter activates, the exposure time becomes longer and frame rate becomes lower, and moving objects may result in blurred images. FIGURE 3-8: SLOW SHUTTER SETTING Manual Gain*

*Only when Automatic Exposure set to Manual can Shutter Speed be adjusted. FIGURE 3-9: MANUAL GAIN SETTING The value of Manual Gain can be set from 0 to 30dB as an increment of 6. This function applies to manual lens only. 30dB brightens the image but noise will be larger and 0dB darkens the image but noise will be smaller. AGC Maximum As an adaptive system found in many electronic devices, the average output signal level is fed back to adjust the gain to an appropriate level for a range of input signal levels. FIGURE 3-10: AGC MAXIMUM SETTING Noise Reduction Noise reduction is the process of removing noise from signal. Users can configure the noise reduction related setting 1~6 to reduce noise on the screen. Selecting 6 provides the best image without noise in low light environment. FIGURE 3-11: NOISE REDUCTION SETTING 25 3.2.1.2 Basic Settings-Image Color A100WIRF SeriesUser Manual FIGURE 3-12: BASIC SETTING IMAGE COLOR Brightness adjustment Set picture brightness from level -255 to 255. Selecting 255 provides brightest the image. Contrast Set picture contrast from level 0 to 128. Selecting 128 provides highest contrast. Saturation Saturation describes the difference of a color from the gray of the same lightness. Increasing saturation deepens the colors of your images, making reds redder and blues bluer. Users can adjust picture saturation level from 0 to 255. Decreasing saturation brings the image closer to a grayscale (that is, monochrome or black-and-white) image. Selecting 255 provides highest image saturation. Hue Set picture hue from level -15~15. Selecting 15 provides the deep hue. FIGURE 3-13: IMAGE COLOR SETTING 26 AWB FIGURE 3-14: AWB SETTING Set the white balance values to correspond to the environment condition for best color rendition. ON: Corrects the colors of camera video automatically. The color temperature range is 2800K ~ 8500K. OFF: Manually adjusted by users. This is useful for some conditions where AWB may be insufficient to perform correctly. You can set the current R/G/B/ color temperature manually. APW: APW is supply for an existed infrared light condition which color performance is better than AWB mode. Note When environment is completed and existed infrared light, we suggest the user to select APW mode. R Gain, G Gain, & B Gain FIGURE 3-15: R/G/B GAIN SETTING Set manual gain value of R Gain, G Gain, & B Gain from level 0 to 255. The red (R) gain is used to adjust the color red in the viewing image. It allows adjusting red gain manually according to user requirement ranging from level 0 to 255. The green (G) gin is used to adjust the color of green in the viewing image. It allows adjusting green gain manually according to user requirement ranging from level to 255. The blue (B) gain is used to adjust the color of blue in the viewing image. It allows adjusting blue gain manually according to user requirement ranging from level 0 to 255. Sharpness Increasing the sharpness value will sharpen the edges and small feature of viewing images. If the edges appear too smooth or blurred, increase the sharpness; otherwise, decrease the sharpness. Sharpness value can be set from 1 to 15. Selecting 15 provides the sharpest image. 27 Backlight Compensation FIGURE 3-16: SHARPNESS SETTING A100WIRF SeriesUser Manual FIGURE 3-17: BACKLIGHT COMPENSATION SETTING Set an area for Backlight Compensation. Backlight Compensation is a function that achieves the brightness of a selected area to optimal image level. This function is necessary when an auto iris lens tends to close due to an intense light coming from back of object in the area wished to view so that the area is too dark and difficult to see. In this case, users may set the area correspond to the portion wished to see. The area size illustrations are roughly as follows. FIGURE 3-18: BACKLIGHT COMPENSATION PICTURE SETTING WDR This function is provided clear images even under back light circumstances where intensity of illumination can vary excessively namely when there are both very bright and very dark areas simultaneously in the field of view of the unit. WDR enables capturing and displaying of both bright and dark areas in the same frame in a way that there are details in both areas, i.e. bright areas are not saturated, and dark areas are not too dark. FIGURE 3-19: WDR SETTING 28 A100WIRF SeriesUser Manual Picture Flip Set image to be upside or down. Select ON or OFF to activate or deactivate the flip function. Picture Mirror Set image to be left or right. Select ON or OFF to activate or deactivate the mirror function. FIGURE 3-20: PICTURE FLIP/MIRROR SETTING Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 29 3.2.1.2 Profile There are up to six profiles to choose from. The one that users are using will be in Current Profile. A100WIRF SeriesUser Manual FIGURE 3-21: PROFILE SETTING In each profile, parameters are all configurable including Image Mode, Resolution, Frame Rate, Bit Rate, Bit Rate Control, and GOP. Be sure to click Save when done. TABLE 3-1: STREAMS/VIDEO QUALITY BASIS Single stream Double Stream Triple Stream Profile 1 720P / H.264 Profile 2 720P / M-JPEG 720P / H.264 Profile 3 720P / H.264 VGA / H.264 Profile 4 720P / M-JPEG VGA / H.264 Profile 5 VGA / H.264 Profile 6 VGA / H.264 720P / M-JPEG N/A N/A VGA / M-JPEG VGA / M-JPEG VGA / M-JPEG QVGA / H.264 VGA / M-JPEG QVGA / M-JPEG Stream 1, Stream 2, and Stream 3 are available for selection for simultaneous triple streams with optimized quality and bandwidth. However, no more than two 720P video can be streamed concurrently. That is to day, 720P video is available for double stream at most with effective either codecs of M-JPEG or H.264. The video signal sent to the Web-Client from the unit has a number of settings that can be edited. The Profiles enable users to configure settings such as Resolution, Frame Rate, and Picture Quality. Since, the unit supports triple streams (for display and storage), they should be configured respectively. 30 FIGURE 3-22: PROFILE SETTING 31 A100WIRF SeriesUser Manual TABLE 3-2: STREAM QUALITY SETTINGS Function Choice Remark Image Mode M-JPEG/H.264 Set a default compression mode. Resolution 720P/VGA/

CIF/QVGA 720P is the highest resolution and, QVGA is the lowest resolution. Frame Rate PAL:5/10/12/25 NTSC:5/10/15/30 The frame rate is displayed per second. PAL: H.264/M-JPEG: 720P, CIF, VGA, QVGA@25fps NTSC: H.264/M-JPEG: 720P, CIF, VGA, QVGA@30fps Bit Rate control mode Variable bit rate/

Constant bit rate Choose the Bit Rate control selection based on user requirements. When chosen Variable bit rate, max and min bit rate values can be set. Compression Ratio Low/Mid/High Low: this setting produces highest image quality while the file size increases. High: this setting produces lowest image quality while the file size decreases. Note: When M-JPEG selected, it will display Compression Ratio as users set according to requirements. Bit Rate 512K/1M/2M/4M/

6M/8M Its optional only when constant bit rate is chosen. Select the desired bit rate among 512K, 1M, 2M, 4M, 6M,and 8M kb/s. GOP 2-64 Select the GOP (Group of pictures) number from 2 to 64. If the number is bigger, recovery of the lost frames will be more difficult; if the number is smaller, it will increase the bite rate obviously and aggravate the network load. The default value is 30, and GOP will be differed by fps setting. 32 TABLE 3-3: STREAM/RESOLUTION BASIS Resolution Codec Double stream Triple stream Primary Secondary Primary Secondary Tertiary 1280720(720P) 640480(VGA) 352240(CIF) 320240(QVGA) 640480/35224 640480/352240/

1280720@30fp s/25fps 0/320240@

30fps/25fps 1280720/6404 H.264/M-JPEG 1280720@

1280720@

30fps/25fps 30fps/25fps 640480@30fps 80/352240/320

/25fps 240@

30fps/25fps 1280720/6404 352240@30fps 80/352240/320

/25fps 240@

30fps/25fps 1280720/6404 320240@30fps 80/352240/320

/25fps 240@

30fps/25fps 320240@

30fps/25fps 640480/352240/

320240@

30fps/25fps 640480/352240/

320240@

30fps/25fps 640480/352240/

320240@

30fps/25fps Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 33 A100WIRF SeriesUser Manual 3.2.1.3 Mask Zone To enable a mask zone, simply press Enable button ON and click Set Mask Zone to start mask setting. Use mouse to drag a mask rectangle on the screen, click OK to complete the selection. Click Save to enable the mask setting. FIGURE 3-23: MASK ZONE SETTING FIGURE 3-24: MASK ZONE EXAMPLE At most 4 masks can be set on the screen concurrently. Note 34 3.2.2 Event Settings 3.2.2.1 Alarm-Motion Detection This function is designed to trigger a video recording when the unit detects a motion. FIGURE 3-25: MOTION DETECTION SETTING Function: Set ON to turn on motion detection and set motion sensitivity and area. Sensitivity: Choose different levels of 1~100 for sensitivity. 100: Motion is activated with slight changes in brightness or motion. 1: Motion is activated with big changes in brightness or motion. Object Size: Choose different levels of 1~100 for object size. Set the percentage area size for a recognizable object. 100%: Very large objects trigger motion. 30%: Small objects trigger motion. Set Motion Area: Set the area you want to trigger motion detection. The motion setup screen will be opened for selecting the detection area by clicking/dragging the mouse. FIGURE 3-26: MOTION AREA SETTING 35 3.2.2.2 E-mail Recording Users can receive motion information by setting an E-mail account. A100WIRF SeriesUser Manual FIGURE 3-27: E-MAIL SETTING E-mail Server Settings Authentication: Select an authentication type. No Authentication: No restriction. PLAIN: PLAIN is the name of a registered SASL authentication mechanism which serves as a parameter to the AUTH command. The PLAIN authentication mechanism is described in RFC 2595. PLAIN is the least secure of all the SASL authentication mechanisms since the password is sent unencrypted across the network. LOGIN: The LOGIN mechanism is supported by Microsoft's Outlook Express as well as by some other clients. TLS_TTLS: TLS is usually implemented on top of any of the Transport Layer protocols encapsulating the application-specific protocols such as HTTP, FTP, SMTP, NNTP and XMPP. The TLS protocol allows client-server applications to communicate across a network in a way designed to prevent eavesdropping and tampering. TLS can also be used to tunnel an entire network stack to create a VPN as is the case with OpenVPN. E-mail Port: set 25 as default or change to dedicated number. E-mail server (SMTP): Input a SMTP server name. E-mail user ID: Input a user name with privilege to access the server. Password: Input the password associated with Login ID. Password(Confirm): Confirm your E-mail password. Administrator E-mail Address: enter your E-mail address. 36 Recording by motion: Setup E-mail condition when motion detection is activated. A100WIRF SeriesUser Manual FIGURE 3-28: RECORDING BY MOTION 1/2 Subject: The subject of the E-mail. Message: The contexts of E-mail. Attach Image: Select on first and choose the image to attach with. Mail to: This function is designed to notify multiple users via email when the motion detection function is set. FIGURE 3-29: RECORDING BY MOTION 2/2 Tick enable and input the email address accordingly. Select Motion for sending E-mail. Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 37 A100WIRF SeriesUser Manual 3.2.3 Network Settings 3.2.3.1 Basic Settings Camera Name: Enter a name for the unit or simply use the default name. DHCP: The IP address is automatically obtained when ON selected; otherwise, select OFF to manually setup the network setting. IP Address: Manually input IP address when DHCP off selected. Subnet Mask: Please use default address: 255.255.255.0. If subnet mask is not properly configured, the unit may not be able to communicate with other devices. Default Gateway: Leave blank as default setting. No Default Gateway address required if not used. Ask your network administrator for further information. Primary DNS: same as above. Secondary DNS: same as above. HTTP Port Number: It is recommended to use the default port number. Please contact your network administrator if you need to change it. The legitimate port number other than 80 is ranging from 1025 to 65535. UPnP: When set to ON, the unit can be detected automatically by the computer in the same network. There would no IP Finder program installation required. FIGURE 3-30: NETWORK BASIC SETTINGS Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 38 3.2.3.2 RTSP Authentication: Enter the Login ID, Password, and RTSP Port number above if ON selected. FIGURE 3-31: RTSP SETTINGS Transfer Type: IP packet transfer type can be either Unicast or Multicast. The unit supports IGMP if in Multicast mode. Multicast Address: Specify multicast address (e.g. of the switch or router) ranging from 224.0.0.23 to 239.255.255.254. FIGURE 3-32: RTSP STREAM SETTINGS Please be reminded of clicking save button to save all your settings on desired options and values. Note: RTSP URLs for Stream 1, Stream 2 and Stream3 are: rtsp://(ip address):(RTSP port)/stream1, rtsp://(ip address):(RTSP port)/stream2, rtsp://(ip address): (RTSP port)/stream3, respectively. For example: rtsp://192.168.0.30:554/stream1 Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 39 1.2.3.3 DDNS This section explains how to configure the dynamic domain name service (DDNS) for network camera. A100WIRF SeriesUser Manual FIGURE 3-33: DDNS SETTINGS DDNS: To click ON to activate the DDNS function or OFF to deactivate DDNS. DDNS server: To select DynDNS or NoIP from the drop-down list of the DDNS Servers. Host Name & Domain name: To enter host name and domain name. User ID: To enter the user ID associated with the DDNS Server. Password: To enter the password associated with the User ID. Password (Confirm): To re-enter the password associated with the User ID. Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 40 A100WIRF SeriesUser Manual 3.2.4 WIFI Settings Below settings control how this unit act in a wireless network. Users can connect to wireless networks and enable wireless encryptions. 3.2.4.1 Basic settings FIGURE 3-34: WIFI BASIC SETTINGS WIFI Function: Select ON to enable subsequent settings. DHCP: The IP address is automatically obtained when ON selected; otherwise, select OFF to manually setup the network setting. IP Address: Manually input IP address when DHCP off selected. Subnet Mask: Please use default address: 255.255.255.0. If subnet mask is not properly configured, the unit may not be able to communicate with other devices. Default Gateway: Leave blank as default setting. No Default Gateway address required if not used. Ask your network administrator for further information. Primary DNS: same as above. Secondary DNS: same as above. Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. Please do not set your IP addresses of LAN and WIFI both in the same subnet in case unavailable to connect message showing while networking with default IP address of the unit. Caution 41 A100WIRF SeriesUser Manual 3.2.4.2 WIFI When WIFI enabled, the unit automatically search wireless networks (as below figure) for users to select and join. Site search list: Survey the local area for available wireless network. The user should select local area network from the search list. FIGURE 3-35 AVAILABLE WIFI NETWORK DIAGRAM WIFI setting Mode: select ad hoc or infrastructure ad hoc(device to device): Select this when connecting to a computer directly. With this setting specify a wireless channel. A wireless access points (AP) are not used. When set ad hoc mode, the user must to select a specific SSID (cube-xxx) for networking. After WIFI networking, the WIFI IP camera default address is 192.168.1.30. Note With ad hoc mode, you cant select security of Public, WPA, WPA2, or None. Infrastructure: Select this when connecting to a computer via an access point (AP) or wireless router. To join the WLAN, the AP and all wireless clients must be configured to use the same SSID. SSID: Service Set Identifier (SSID) is a network name used to be identified the wireless signal emitted from a wireless access point. The SSID listed here should be the one users selected in the above figure. The field space is up to 30 alphanumeric characters, and the name must exactly the same as that used in the wireless access point. Otherwise, no connection will be established. 42 A100WIRF SeriesUser Manual Security: This unit supports four wireless security options, None (no data encryption), WPA-Personal, WPA2-Personal and Public. WIFI Protected Access (WPA-Personal/WPA2-personal) and Public offer different levels of security for wireless communication by encryption to protect data transmitted over a wireless network. The WPA2/WPA is more secure than Public because WPA2/WPA use dynamic key encryption. It is recommended to enable the highest level of encryption supported by the network infrastructure. Encryption:

WEP- Wired Equivalent Privacy (WEP) is a basic encryption method which transmits network broadcast messages using radio signals. WEP provides a minimum level of security that can deter minor intrusions. TKIP- Temporal Key Integrity Protocol (TKIP) is an encryption protocol included as part of the IEEE 802.11i standard for wireless LANs (WLANs). It was designed to provide more secure encryptions than the notoriously weak Wired Equivalent Privacy (WEP), the original WLAN security protocol. TKIP is the encryption method used in Wi-Fi Protected Access (WPA), which replaced WEP in WLAN products. AES- Advanced Encryption Standard (AES) offers a higher level of security and is approved for government use, but requires a hardware upgrade for implementation. As organizations replace older wireless equipment, AES is expected to become the accepted encryption standard for WLAN security. FIGURE 3-36: WIFI SECURITY SETTING When Public is selected in Security, WEP will be displayed in Encryption, and Key shows automatically. FIGURE 3-37: WIFI SECURITY SETTING 43 When WPA-Personal is selected in Security, TKIP or AES will be displayed in Encryption, and Key shows automatically. The default is TKIP. A100WIRF SeriesUser Manual FIGURE 3-38: WIFI SECURITY SETTING When WPA2-Personal is selected in Security, TKIP or AES will be displayed in Encryption, and Key shows automatically. The default is TKIP. FIGURE 3-39: WIFI SECURITY SETTING Note The Encryption key must be the same value used by the wireless access point (AP). Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. WPS Settings Wi-Fi Protected Setup (WPS) is a computing standard that attempts to allow easy establishment of a secure wireless home network. WPS supports two connection ways. One is PIN Code and the other one is PBC(Push Button correction) . PIN code:

1. Remember IP camera pin code(99956042) and simultaneously Key-in 8 digitals pin code to AP device 2. Click Start PIN code between AP and IP camera 3. Then WPS will be connecting. Button to set:

1. Push WPS button on AP device and simultaneously push default button on IP camera at 2sec 2. Or Push WPS button on AP device and push Start PBC button on IP camera by UI configuration 3. Then WPS will be connecting. FIGURE 3-40: WIFI SECURITY SETTING 44 3.2.5 Account 3.2.5.1 Administrator Information Press the item-Administrator Function on setting menu. Unit privilege control can be defined right here. The default setting for system Admin ID and password is:

User ID: admin Password: 1234 Language: English Administrators can enter their own Admin ID, password, Language preference (English or Simplified Chinese) here. FIGURE 3-41: ADMINISTRATOR INFORMATION Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 45 A100WIRF SeriesUser Manual 3.2.5.2 User Information Other than administrator, guests can access to the unit under authorization from system administrator. However, 5 users are allowed to view the live picture at most. No operation will be granted without authorization. The default guests login name and password are user1 (user+1~5) and 0000. To change the setting, simply follow steps below. Enter a guests User ID in the User ID field Enter a password associated with a guests User ID Re-enter the password again to confirm it Choose language: English and Simplified Chinese FIGURE 3-42: USER INFORMATION Caution The login ID and Password is supported less than 16 characters and input valid value only from '0' to '9', 'a' to 'z', 'A' to 'Z', '.','-','+','_'and '@'. Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 46 3.2.6 System 3.2.6.1 Audio Function: Select "ON" to enable receiving audio from a microphone connected to the unit. Audio Input Level: Select among High, Mid, and Low for sound input level. FIGURE 3-43: AUDIO INPUT 3.2.6.2 Date/Time Synchronization Mode: Users can choose 3 different type of Synchronization Mode here as needed. Date & Time manual setting: To set up the units date and time. FIGURE 3-44: SYNCHRONIZATION MODE NTP Server FIGURE 3-45: DATE & TIME MANUAL SETTING Time Zone: To select the time zone where the unit is located. NTP Server: To state the address of NTP server to synchronize date and time with the unit when If NTP is selected in the Synchronization Mode. Time Adjustment Period: To select the interval to calibrate the time of the unit. Save &Test: To save and test NTP server settings. FIGURE 3-46: NTP SERVER 47 Daylight saving: To activate the daylight-saving function if in a daylight saving time zone (effective in NTP mode only). A100WIRF SeriesUser Manual FIGURE 3-47: DAYLIGHT SAVING Note Please click Save button to save your settings. Users can click Reset to return last setting and also click Default to set all the data and options back to defaults. 3.2.6.3 Update Users can update system firmware if an update file is available. It is the customer's responsibility to update firmware. All camera motions will shut down during firmware update. Close any other screens before starting a firmware update. Never disconnect power and LAN cable during the firmware update process, or an update failure will occur and maintenance will be required. Rebooting the unit after firmware update may take approximately 3 minutes. After finished FW update, please reboot your computer as well. Caution We suggest the user to use LAN cable for the firmware update as the wireless is not very stable platform. FIGURE 3-48: FIRMWARE UPDATE 48 3.2.6.4 Configuration Import Configuration Settings: To upload configuration setting from the computer to the unit. FIGURE 3-49: IMPORT CONFIGURATION SETTINGS Export Configuration Settings: To export configuration settings of the unit to the computer. FIGURE 3-50: EXPORT CONFIGURATION SETTINGS Set to Factory Default: To reset all configuration settings into factory default. Network Camera Reboot: To reboot the unit. FIGURE 3-51: SET TO FACTORY DEFAULT FIGURE 3-52: NETWORK CAMERA REBOOT 49 A100WIRF SeriesUser Manual 3.2.7 Event Log Simply click Event Log on the setting menu, and click the buttons for administrations such as to display the desired logbooks or to delete all logs. FIGURE 3-53: EVENT LOG 3.2.8 Client 3.2.8.1 Record This function is to define the way to record video once a motion/schedule event is detected by the unit. Motion Record Select ON or OFF to use this function. When camera detected a motion event, the image will be automatically saved into a specific field. If you enabled motion record, please also turned on event setting of motion detection. For more information, please refer to 3.2.2 event setting. FIGURE 3-54: CLIENT-MOTION RECORD Select ON or OFF to use this function. Schedule Record 50 FIGURE 3-55: CLIENT-SCHEDULE RECORD Determine the recording condition: Stop, All Day, Schedule 1, or Schedule 2 from scheduled recording table during 24/7. Stop: stop recording. All day: 24hr recording. Schedule 1 or Schedule 2: the user can set the recording time from 00:00 to 23:59. Recording type: Select either way (Normal or Motion). Normal: the end user can set a period of time to record the video. Motion: when motion event is detected during your setting schedule, the image will be recorded. Caution Recording priority: Motion Normal. When detected motion event, the normal recording will be stopped operating. The video file will be different when chosen motion or normal. Please keep your HD space around 10G. Otherwise if your HD space is below 5G, the older recording file will be automatically deleted and always kept the new one. Note Please click Save button to save your settings. 3.2.9 Information Simply click Information on the setting menu, FW version, MAC address, and WIFI Mac Address will be displayed. FIGURE 3-56: INFORMATION 51 Appendix: Specification of A100WIRF Series A100WIRF SeriesUser Manual Model Type Model No. Signal System Warranty Image System Image Sensor Sensor Type Optical System Lens Mount Focal Length F No Angel Of View Electric Digital Noise Reduction Minimum Illumination S/N Ratio Gain Control White Balance Electric Shutter Audio In/Out Network Specification Video Compress Video Streaming Frame Rate Resolution Network Protocols Wireless Slow Shutter WDR Back Light Compensation Audio Format Privacy Zone Motion Detection Security Access Users Application ONVIF Web Browsing Requirements Mechanism Dimensions Weight Connectors IR IR Distance IR LED IR Wavelength Mega Wireless Cube IR Camera A100WIRF-HNH-03 NTSC A100WIRF-HPH-03 PAL 1 year 1/4 OV9715 CMOS M12 Fixed 3.6mm F2.0 66(Diagonal), 58(Horizontal), 35(Vertical) 3D F=2.0, CL: 0.8 lux@50 IRE, IR LED ON: 0 lux 50dB (AGC off) Off/On, Selectable Off/ On/ APW(2800K~8500K) 1/30~1/8000 sec 1/25~1/8000sec Audio In / Audio Out (Optional) H.264/M-JPEG Triple Streaming 720P(1280 x 720) @30fps 720P(1280 x 720) @25fps 720P(1280 x 720), VGA(640 x 480), QVGA(320 x 240), CIF(352 x 240) IPv4, HTTP, TCP, RTSP/RTCP/RTP, ICMP, UDP, IGMP, DNS, DHCP, ARP, NTP, UPnP, SMTP 802.11 b/g/n Yes Digital WDR Off/ On (6 Area Selectable) G711-Alaw Yes Yes Multiple Privilege Control (LAN) WEP, WPA, WPA2 (Wireless) 1 Administrator, 5 Viewers SDK 2.0 / IP Finder 3.3 ONVIF compliance test tool pass Microsoft Internet explorer 8.0 or above 89mm (H) x 80.7mm (W) x 250.2mm (L) 110g Power in: DC jack Network: RJ45 connector 8M 8pcs Red LED 850nm 52 DC 5V 4W Max Power Supply Power Requirement Power Consumption Environment Operating Temperature Operating Humidity Storage Temperature Storage Humidity Safety Regulation FCC CE Regulation Note: Product specifications and pictures are subject to change without notice. 0% to 90%, non-condensing

-10C ~ 40C

-20C ~ 60C Class B Class B 0% to 90%, non-condensing 53