User MANUAL Wireless LAN with Bluetooth module Model Name: GN-4030 Brand: TOSHIBA GC-4030 Page 1/10 2019/6/19 CONTENT 1 PRODUCT OVERVIEW ...................................................................................................................... 6 1.1 1.2 1.3 1.4 1.5 FEATURES .................................................................................................................................. 6 GENERAL SPECIFICATIONS......................................................................................................... 6 BOARD OUTLINE ........................................................................................................................ 7 CONNECTOR PIN CONFIGURATION ........................................................................................... 8 CONNECTOR SPEC ..................................................................................................................... 8 1.6 MAC LABEL ................................................................................................................................ 9 1.7 EEPROM INFORMATION.......................................................................................................... 10 GC-4030 Page 2/10 2019/6/19 FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi transmitter product procedures. Referring to the multi transmitter policy, multiple transmitter(s) and module(s) can be operated simultaneously without C2PC. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. GC-4030 Page 3/10 2019/6/19 20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains FCC ID: BJI-GN4030". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. OEM Integrator Checklist The party below will implement the LITE-ON Module in host systems in accordance with the instructions specified in this document and the documents referenced herein. 1.The OEM integrator will ensure the Module is integrated in a host systems using only the approved antenna model(s) described in this document. 2.The OEM integrator will ensure the antenna placement inside the host system willmaintain the required spacing to end user for RF Exposure compliance, as specified in this document. 3.If other radios are integrated inside the host with the LITE-ON Module, the OEM integrator will contact its test lab, TCB or LITE-ON to determine if additional FCC compliance evaluation is required to meet FCC collocation rules. 4.The OEM integrator will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself are labeled as specified in this document. 5. The OEM integrator will ensure the Module is programmed in the factory with compliant transmit power not exceeding the levels specified in this document. LITE-ON requests that the OEM integrator acknowledge its receipt of this document and the above instructions. You may contact LITE-ON with any GC-4030 Page 4/10 2019/6/19 questions concerning this document or the responsibilities of the OEM integrator IC statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1)This device may not cause interference.
(2)This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Dclaration dexposition la radiation : Cet quipement respecte les limites dexposition aux rayonnements IC dfinies pour un environnement non contrl. Cet quipement doit tre install et mis en marche une distance minimale de 20 cm qui spare llment rayonnant de votre corps. Lmetteur ne doit ni tre utilis avec une autre antenne ou un autre metteur ni se trouver leur proximit. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 25 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 1004C-GN4030. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 25cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 1004C-GN4030". GC-4030 Page 5/10 2019/6/19 1 PRODUCT OVERVIEW 1.1 FEATURES Operate at 2.4GHz / 5GHz band 867Mbps PHY Rate Support 2T2R Mode USB 2.0 support for date rates up to 12Mbps full speed and 480Mbps high speed IEEE standards support: IEEE 802.11a/b/g and 802.11n/ac Bluetooth supports up to V4.2 802.11i- WEP 64/128, AES, TKIP RoHS compliance Halogen Free compliance 1.2 GENERAL SPECIFICATIONS Main Chipset Standard Bus Interface Data Rate Frequency Range Transmit Output Power Receive Sensitivity RTL8822BU IEEE 802.11ac/a/b/g/n , Bluetooth 4.2 LE USB 2.0 for WLAN and BT controller WiFi:
802.11b:
CCK, DQPSK, DBPSK 802.11a, 802.11g:
64QAM, 16QAM, QPSK, BPSK 64QAM, 16QAM, QPSK, BPSK 802.11n:
802.11ac:
256QAM, 64QAM, 16QAM, QPSK, BPSK Bluetooth:
GFSK, /4-DQPSK and 8-DPSK 2.400 ~ 2.4835 GHz 5.150 ~ 5.85GHz WiFi:
11b: 15+/-1.5dBm(11Mbps) 11a/g: 13+/-1.5dBm(54Mbps) 2.4G:
11n: 13+/-1.5dBm(MCS7HT20) 11n: 12+/-1.5dBm(MCS7HT40) 5G:
11n: 12+/-1.5dBm(MCS7HT20) 11n: 11+/-2dBm(MCS7HT40) 11ac: 9+/-2dBm (HT80) Bluetooth:
6dBm WiFi:
11b @ 11Mbps: (Max.) : -85dBm , (Typical) : -89.5dBm (PER<8%) 11g @ 54Mbps: (Max.) : -69dBm , (Typical) : -76dBm (PER<10%) GC-4030 Page 6/10 2019/6/19 11n @ MCS7 (2.4g HT20): (Max.) : -67dBm , (Typical) : -74.5dBm (PER<10%) 11n @ MCS7 (5g HT20): (Max.) : -67dBm , (Typical) : -73.5dBm (PER<10%) 11n @ MCS7 (5g HT40): (Max.) : -64dBm , (Typical) : -70dBm (PER<10%) Bluetooth:
1DH5 BDR: (Max.): -86 dBm , (Typical): -95.5 dBm (BER < 0.1%) 2DH5 EDR: (Max.): -86 dBm , (Typical): -92.5 dBm (BER < 0.01%) 3DH5 EDR: (Max.): -80 dBm , (Typical): -86 dBm (BER < 0.10%) BLE : (Max.): -90dBm , (Typical): -97dbBm (PER<30.8%) Normal Test Condition: 25 +/- 2deg.C , 65 +/- 2% RH Operating: 0 to 70 deg.C Storage: -40 to 85 deg.C Temperature &
Humidity Operating Voltage 3.3V 10% I/O supply voltage Antenna Type Printed Antenna *3( 2 for WIFI + 1 for Bluetooth) 1.3 BOARD OUTLINE PCB thickness = 1.0 mm Module total height = 1.0 + 5.7(WTB connector height) + 0.1(solder paste)
= 6.8 mm (Maximum) GC-4030 Page 7/10 2019/6/19 1.4 CONNECTOR PIN CONFIGURATION WTB Connector (SM07B-PASS) Pin 1 2 3 4 5 6 7 Pin 1 2 3 4 5 Description 3.3VS RESET(Chip-EN) WL_WAKE_HST HST_WAKE_WL GND BT_WAKE_HST HST_WAKE_BT NC D-
D+
NC GND USB miniB Connector (KS-BS-5B-L) Description 1.5 CONNECTOR SPEC WTB Connector (SM07B-PASS) Model No. SM07B-PASS Dimensions A 12.0 mm Dimensions B 18 mm GC-4030 Page 8/10 2019/6/19 USB miniB Connector (KS-BS-5B-L) 1.6 MAC LABEL GC-4030 Page 9/10 2019/6/19 1.7 EEPROM INFORMATION Channel Plan Vendor ID Product ID
(Japan): 0x27 0x0BDA 0xB82C GC-4030 Page 10/10 2019/6/19