FCC ID: 2BCGWHS200BLE Kasa Smart Wi-Fi Light Switch, Single Pole

Wire Your Switch 1 Turn off the circuit breaker. Then remove the old wallplate of the wall switch and label the wires. 3 Connect the wires to the smart switch as shown below. 4 Line up the switch with the mounting holes. Secure it with screws. 5 Attach the wallplate and turn on the circuit breaker. Then the wiring is finished. Ground: Usually green or copper. Neutral: Usually white, not connected to the dumb switch. Line/Load: Usually black, and connected to the dumb switch. If you are unsure, consult a qualified electrician. 2 Disconnect wires from the old switch. Note: No need to distinguish between Line and Load wires. Set Up Your Switch STEP 1 DOWNLOAD APP Get the Kasa Smart app from the App Store or Google Play. OR STEP 2 SET UP Tap the button in the app. If your device is white, select Smart Switches > Smart Switch (Wi-Fi). If your device is black or almond, select Smart Switches > Smart Switch (BLE). And then follow app instructions to complete setup. Appearance Button Explanations Third-Party Services Reset On/Off Button LED Restart Reset Press and hold for about 5s until the LED blinks amber and green to reset Wi-Fi while keeping other settings. Press and hold for about 10s until the LED blinks amber to restore to factory default settings. Restart Press to restart your switch. LED Status Solid amber Starting up. Blinking amber & green Ready for setup;

Resetting Wi-Fi. Blinking green Connecting to Wi-Fi. Stay green for 30s Connected to Wi-Fi. Solid red Disconnected from Wi-Fi. Blinking amber Device resetting. White Light fixture is off. Kasa works with Alexa, Google Assistant, and other third-party services to control your switch by voice. Go to Me > Third-Party Services in the Kasa Smart app to integrate Third-Party Services. For step-by-step setup instructions, please visit:

Google Home Assistant:

https://www.tp-link.com/support/faq/1534/

Amazon Alexa:

https://www.tp-link.com/support/faq/944/

Specifications Rating: 100-120V~ 50/60Hz Load: 15 A General Use, 600 W Incandescent, 1/6 HP Motor Operation temperature: 0~40 Method of mounting included: Independently mounted (Vertically position only);

Operating control, Type 1.C action Pollution Degree 2, Rated Impulse Voltage 2500V Software Class A, NEMA Type 1 CAUTION High Voltage-Disconnect power supply before servicing MISE EN GARDE Haute tension. Dbrancher l'alimentation lectrique avant d'utiliser Safety Notice Before installing, servicing or removing the switch, read and follow all safety precautions including the following:

CAUTION Risk of Electric Shock More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off. The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician. Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces. Install only in a suitable UL Listed outlet box (suitable dimensions:

H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm). Support Quick Start Guide Kasa Smart Wi-Fi Light Switch, Single Pole HS200/HS200-LA/HS200-BL For technical support, the user guide and other information, visit https://www.tp-link.com/support/. 2023 TP-Link 7106510623 REV6.0.0

*Images may differ from your actual product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

Th

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Canadian Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B

A B C D E 1 7202509537 2 3 4 5 6 7 8 9 38.3 1R 4.8R 38.5 5 6 5

. HS200-LA Kasa Smart Wi-Fi Light Switch, Single Pole Rating: 100-120 V~ 50/60 Hz 15 A General Use 600 W Incandescent 1/6 HP Motor FCC ID: 2BCGWHS200BLE UL6.0 E536793 Model: HS200-LA(US) Ver:6.6 VN1 MADE IN VIETNAM S/N:XXXXXXXXXXXXX 38.5*56.50.2mm, 4.8 R,1R 1 2 3 4 5 6 HS200-LA(US)_6.6_ A1 PANTONE 877C 50#PET+

PANTONE 877C

-128 HS200-LA(US)_6.6 2023-09-08 UL 7 8 9 A B C D E label location

Big Field Global PTE. Ltd. Wi-Fi Channel 12 and 13 Declaration Letter Date: 2023-12-01 We, the undersigned company Company Name: Big Field Global PTE. Ltd. Address: 7 Temasek Boulevard #29-03 Suntec Tower One, Singapore 038987 Declare that:

Product description: Kasa Smart Wi-Fi Light Switch, Single Pole Type designation: HS200-LA, HS200-BL Trademark: tp-link, kasa FCC ID: 2BCGWHS200BLE Only channels 1~11 will be used in USA. Country code selection is disabled. If you have any questions regarding the authorization, please do not hesitate to contact us, thank you~

Sincerely, Signature: ________________________ Name: Sarah Wang Position: Regulatory Compliance Manager

U.S. Agent Designation for Service of Process

(Applicant and U.S. Agent are Separate Parties) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification Section 2.911(d}(7) Information Designated U.S. Agent Company Name: VISHTEC LLC Contact Name: Alan Graham Street Address: 9888 W Belleview Ave Ste 2142 Denver CO 80123 City/Province/Zip: 80123 Telephone No: (571) 4007350 Email: Alan.graham@vish-tec.com FRN #: 0033407131 This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process for the limited purpose of compliance with section 47 CFR 2.911(d)(7) only and not for any other purpose, on behalf of the Applicant noted below. U.S. Agent Signature:

For and on behalf ot Date:2023/8/28 VISHTEC LLC The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-

related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Big Field Global PTE. Ltd. Grantee Code: 2BCGW FRN #: 0034122556 Contact Name: Sarah Wang Street Address: 7 Temasek Boulevard #29-03 Suntec Tower One, Singapore 038987 City/Province/Zip: Singapore Telephone No: +65-97538388 Email: certification@tp-link.com Applicant Signature: Sa Date: 2023/8/28 rah Wa Signed by (Printed Name/Title) Sarah Wang 1. Letters should be placed on appropriate letterhead.

Big Field Global PTE. Ltd. Model Declaration Letter We, the undersigning company Company Name: Big Field Global PTE. Ltd. Address: 7 Temasek Boulevard #29-03 Suntec Tower One, Singapore 038987 Hereby confirm that the following products:

Product description: Kasa Smart Wi-Fi Light Switch, Single Pole Type designation: HS200-LA, HS200-BL Trademark: tp-link, kasa That All versions of the Model HS200-LA and HS200-BL are electrically equal except the following difference:

1. Only differ in model name and colour, HS200-LA is light apricot, HS200-BL is black, and everything else is exactly the same. Contact Person: Sarah Wang Position in the Company: Regulatory Compliance Manager Date: 2023/12/01 Signature:

Big Field Global PTE. Ltd. To: Federal Communications Commission Date: 2023/12/01 7435 Oakland Mills Road Columbia, MD 21046 USA Attestation Section 2.911(d)(5)(i) and Section 2.911(d)(5)(ii)

(KDB 986446 D01 Covered Equipment) Section 2.911(d)(5)(i) Big Field Global PTE. Ltd. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Section 2.911(d)(5)(ii) Big Field Global PTE. Ltd. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. FCC ID: 2BCGWHS200BLE If you have any questions, please feel free to contact me Contact Person:

Position in the Company: Regulatory Compliance Manager Date of Signature:

Sarah Wang 2023/12/01 ___________________________ Signatory

(signature of the applicant)

Big Field Global PTE. Ltd. Authority to Act as Agent Date: December 1, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

BTL Inc./Rose Liu is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: 2024-12-01 By:

(Signature1) Sarah Wang

(Print name) Title:

Regulatory Compliance Manager On behalf of: Big Field Global PTE. Ltd.

(Company Name) Telephone:

+86 755 21534921 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 030122-15

Big Field Global PTE. Ltd. Request for Confidentiality Date: December 1, 2023 Subject: Confidentiality Request for: 2BCGWHS200BLE Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *1 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Big Field Global PTE. Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

Regulatory Compliance Manager

(Signature/Title3) Sarah Wang

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 030122-15