FCC ID: 2BH7FEAP100BRG 2.4GHz 300Mbps Indoor/Outdoor Wireless Bridge

Regulatory Compliance Indoor/Outdoor EAP 2025 TP-Link 1910013244 REV2.3.0 For Class B EAP with adapter:

FCC Compliance Information Statement Product Name: Omada Indoor/Outdoor Access Point/Wireless Bridge Model Number: EAP100-Bridge / EAP211-Bridge V3 / EAP215-Bridge V3 / Beam Bridge 5 UR /

EAP603-Outdoor / EAP610-Outdoor / EAP725-Outdoor Component Name Model T120100-2B1 (for EAP100-Bridge) POE2412G (for EAP211-Bridge V3 / EAP215-Bridge V3 /

Beam Bridge 5 UR) POE4824G (for EAP603-Outdoor) TL-POE4824G (for EAP610-Outdoor) I.T.E. Power Supply Responsible party:

TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: [email protected] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 25cm (for EAP610-Outdoor / EAP100-Bridge) / 20cm (for other models) from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. Product Name: I.T.E. Power Supply Model Number: T120100-2B1 / POE2412G / POE4824G / TL-POE4824G Responsible party:

TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: [email protected] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2025/08/11 CE Mark Warning OPERATING FREQUENCY (the maximum transmitted power) For EAP100-Bridge:

2412MHz2472MHz (20dBm) For EAP211-Bridge V3 / EAP215-Bridge V3 / Beam Bridge 5 UR:

5150MHz5250MHz (23dBm) 5250MHz5350MHz (23dBm) 5470MHz5725MHz (30dBm) For EAP610-Outdoor:

2412MHz2472MHz (20dBm) 5150MHz5250MHz (23dBm) 5250MHz5350MHz (23dBm) 5470MHz5725MHz (30dBm) For EAP603-Outdoor / EAP725-Outdoor:

2402 MHz-2480 MHz (10dBm) 2412MHz2472MHz (20dBm) 5150MHz5250MHz (23dBm) 5250MHz5350MHz (23dBm) 5470MHz5725MHz (30dBm) EU Declaration of Conformity For EAP725-Outdoor:

TP-Link hereby declares that the Access Point is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2011/65/EU and (EU)2015/863. For other models:

TP-Link hereby declares that the Access Point is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and

(EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/

ce/. RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20cm from your body. National Restrictions For EAP211-Bridge V3 / EAP215-Bridge V3 / Beam Bridge 5 UR / EAP603-Outdoor / EAP610-

Outdoor / EAP725-Outdoor:

Frequency band: 5150 - 5250 MHz:

Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band. Frequency band: 5250 - 5350 MHz:

Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted. Frequency band: 5470 - 5725 MHz:

Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems

(UAS) are not permitted. UKCA Mark UK Declaration of Conformity TP-Link hereby declares that the Access Point is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca National Restrictions For EAP211-Bridge V3 / EAP215-Bridge V3 / Beam Bridge 5 UR / EAP603-Outdoor / EAP610-

Outdoor / EAP725-Outdoor:

Attention: In Great Britain, the operation in the frequency range 5150MHz - 5350MHz is only permitted indoors. UK Canadian Compliance Statement EAP100-Bridge / EAP211-Bridge V3 / EAP215-Bridge V3 / EAP610-Outdoor:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. EAP603-Outdoor:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This radio transmitter (IC: 32876-EAP603OD/ Model: EAP603-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list below, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 32876-EAP603OD/ Model: EAP603-Outdoor) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste ci-dessous et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Three 5GHz 5.14 dBi dipole antennas Antenna Two 2.4GHz 4.08 dBi dipole antennas (for Wi-Fi) One 2.4GHz 3.66 dBi dipole antenna (for Bluetooth) EAP725-Outdoor:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This radio transmitter (IC: 32876-EAP725OD / Model: EAP725-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list below, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 32876-EAP725OD / Model: EAP725-Outdoor) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste ci-dessous et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Two 5GHz 5.33 dBi dipole antennas (For Wi-Fi) Two 5GHz 13.18 dBi microstrip antennas (For Wi-Fi) Antenna Two 2.4GHz 4.50 dBi dipole antennas (For Wi-Fi) Two 2.4GHz 8.33 dBi microstrip antennas (For Wi-Fi) One 2.4GHz 3.61 dBi IFA antenna (For Bluetooth) Caution Professional installation instruction

(For EAP211-Bridge V3 / EAP215-Bridge V3 / EAP603-Outdoor / EAP610-Outdoor / EAP725-

Outdoor) 1. Installation personnel This product is designed for specific application and needs to be installed by a qualified trained person who has RF and related rule knowledge. This product needs to be professionally configured by SDN Controller network service before use. 2. Professional Installation Requirements This device is generally for industrial/commercial use, which only sold to authorized dealers or installers. Operation in the 5150-5250MHz is restricted to indoor use only.

(For models with DFS function:) Operation in the 5600-5650MHz band is prohibited. Instructions d'installation pour les professionnels

(Pour EAP211-Bridge V3 / EAP215-Bridge V3 / EAP603-Outdoor / EAP610-Outdoor / EAP725-

Outdoor) 1. Personnel d'installation Ce produit est conu pour une application spcifique et doit tre install par une personne qualifie et forme, possdant des connaissances en RF et en rgles associes. Ce produit doit tre configur par des professionnels via le service rseau SDN Controller avant utilisation. 2. Exigences d'installation lattention des professionnels Cet appareil est gnralement destin un usage industriel/commercial, vendu uniquement des revendeurs ou installateurs agrs. Le fonctionnement dans la bande 5150-5250 MHz est limit une utilisation en intrieur uniquement.

(Pour les modles avec fonction DFS:) Le fonctionnement dans la bande 5600-5650 MHz est interdit. For EAP211-Bridge V3 / EAP215-Bridge V3 / EAP610-Outdoor:

1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong. For EAP603-Outdoor / EAP725-Outdoor:

1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong. 2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

3) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-

5600MHz, and 5650-5725MHz. Avertissement Pour EAP211-Bridge V3 / EAP215-Bridge V3 / EAP610-Outdoor:

1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

Pour EAP603-Outdoor / EAP725-Outdoor:

1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

2) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la limitation P.I.R.E.;

3) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer la limitation P.I.R.E spcifie pour lexploitation point point et non point point, selon le cas. Les produits utilisant la technique d'attnuation DFS (slection dynamique des frquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm

(for EAP100-Bridge / EAP610-Outdoor) / 20cm (for other models) between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 25cm (pour EAP100-Bridge / EAP610-Outdoor) / 20cm (pour les autres modles) de distance entre la source de rayonnement et votre corps. Industry Canada Statement CAN ICES (B)/NMB (B) Korea Warning Statements

. NCC Notice & BSMI Notice EAP603-Outdoor / EAP725-Outdoor

( ) 40 PCB Pb Cd Hg CrVI PBB PBDE 1. "0.1 wt %" "0.01 wt %" . 2."". 3."" .

. Safety Information Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended. Do not use the device where wireless devices are not allowed.

(For models with adapters) The socket-outlet shall be installed near the equipment and shall be easily accessible.

(For models with adapters) Make sure the power socket has a good contact with the ground.

(For models with adapters) Plug the product into the wall outlets with earthing connection through the power supply cord.

(For models with adapters) Adapter shall be installed near the equipment and shall be easily accessible.

(For models with adapters) Adapter should be used indoors where the ambient temperature is lower than or equal to 40 .

(For models with adapters) Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please dont hesitate to contact us. Operating Temperature ( ):

EAP100-Bridge / EAP211-Bridge V3 / EAP215-Bridge V3 / Beam Bridge 5 UR: -40 70

(-40 158 ) EAP610-Outdoor: -30 60 (-22 140 ) Others ( ): -30 70 (-22 158 ) This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. Explanation of the symbols on the product label Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products. I.T.E. Symbol Explanation Class II equipment Class II equipment with functional earthing Alternating current Direct current DC Polarity of d.c. power connector For indoor use only Dangerous voltage Caution, risk of electric shock Energy efficiency Marking Protective earth Earth Frame or chassis Functional earthing Caution, hot surface Caution Operator's manual Stand-by

"ON"/"OFF" (push-push)

Fuse Fuse is used in neutral N N RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. 2012/19/EU WEEE Caution, avoid listening at high volume levels for long periods Disconnection, all power plugs Switch of mini-gap construction Switch of micro-gap construction (for US version) Switch of micro-gap / micro-disconnection construction (for other versions except US) US

/ US Switch without contact gap (Semiconductor switching device) m Mounting Requirements For safety, we recommend you to use the original screws in the package when mounting. The following are alternatives to mount the device on the wall:

(For EAP603-Outdoor / EAP610-Outdoor / EAP725-Outdoor) Use 2 screws which comply with ANSI B1.1 4#, (5#), 6# standard and are longer than 7 mm.

( EAP603-Outdoor / EAP610-Outdoor / EAP725-Outdoor) ANSI B1.1 4#, (5#), 6# 7 2 ANSI B1.1 d(mm) dk (mm) k (mm)

1 Hardware Overview 2 Site Consideration LED Explanation Mounting Height Signal LEDs LAN LEDs SYSTEM LED Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. Line of Sight 3 Lightning and ESD Protection Proper grounding is extremely important for outdoor devices. To reduce the damage of potential lightning and ESD attacks, connect the APs grounding terminal to grounding facilities using a proper grounding wire, which should meet local installation requirements. LED Indication Signal LEDs Work as Main AP:

All LEDs remain solid on. Work as Client AP:

More lit LEDs indicates better wireless signal strength. LAN LEDs On: The port is connected, but not active. Flash: The port is connected and active. Off: The port is not connected. SYSTEM LED On: Working normally/Initializing Off: Working abnormally/Power off/LED is turned off. Flash:

Flash twice: Initialization is completed. Flash quickly: The AP is resetting, or the Omada Controller is locating the device*. Flash once per second: The AP is upgrading. Sustained Flash: The AP is in the isolated state.

* When the Locate feature is activated in the Omada Controller, the APs SYSTEM LED will flash quickly for 10 minutes to help you locate and identify the device. You can disable this feature manually to stop the device from flashing. Panel Layout Side View Orientation With built-in directional antennas, the Bridge AP provides sector-shaped network coverage. Install the AP with the front facing the target area. For antenna and horizontal beamwidth details, refer to the product datasheet on our official website. Grounding Terminal Grounding Cable Earth Ground Power On 4 The AP can be powered only by a power adapter, a PSE device

(such as a PoE switch), or a passive PoE adapter. Option 1: Via Power Adapter Quick Installation Guide Indoor/Outdoor Wireless Bridge Note: EAP211-Bridge KIT is used for demonstration. Images may differ from your actual product. 2025 TP-Link 7100000223 REV3.1.1 Package Contents The KIT product contains a Main AP, a Client AP, two sets of accessories, and an Installation Guide. The Main AP and Client AP can be distinguished by the role switch on the product. RESET Button Grounding Terminal Main AP Client AP Power Port Role Switch

(Main AP/Client AP) For long-range AP models, you can orient the APs with the assistance of Google Maps, GPS and some landmarks. Power Adapter Power Port Pole Mounting Straps Quick Installation Guide LAN1(PoE IN) LAN2 LAN3 A Option 2: Via PoE Switch APs AP Covers Installation Guide Item Description RESET Button Press and hold for about 5 seconds to reset the AP to its factory settings. Grounding Terminal Connect to grounding facilities for lightning and ESD protection. LAN1 (PoE IN) Port Connect to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and power supply. LAN2/LAN3 Port Connect to a client device for data transmission. Power Port Connect to a wall outlet for DC power input. Role Switch

(Main AP/Client AP) Distinguishes whether the AP works as the Main AP or Client AP. If needed, you can toggle left or right to change the AP's role. Line of Sight Horizontal Beamwidth B LAN1(PoE IN) PoE Switch Option 3: Via Passive PoE Adapter LAN1(PoE IN) Passive PoE Adapter Auto Pairing 5 The Main AP and Client AP in the same KIT will automatically form a bridge network after powering on. The Signal LEDs on the APs will turn on. Note: If you have other Bridge APs, refer to the Network Management section to add them manually. 1. Check the role switch to ensure you connect the Main AP and Client AP in the network correctly. You can toggle the role switch to change the APs role if needed. 2. The default SSID on the product is only for device access and management. If you need an SSID to access the internet and service networks, refer to the Network Management section to set up the AP. 3. In a network without a DHCP Server, Bridge APs will use the following DHCP fallback IP addresses:

Main AP: 192.168.0.254 Client AP: 192.168.0.253 Typical Application 1: Remote Camera Monitoring Auto Pairing

(Optional) Network Management 7 If you want to change AP settings, manage the network, or add other APs to the network, choose a method below:

Method 1: Standalone Mode Configure and manage APs through the Main AP (Convenient for a small network with only a few devices) Method 2: Controller Mode Configure and manage APs in batches on a central platform, namely the Omada Controller. Method 1: Standalone Mode If your network has only a few devices, you can configure and manage Bridge APs through the Main AP. Note: The APs web page is inaccessible while the AP is managed by a Controller. Method 2: Controller Mode Omada Controller integrates Omada gateways/routers, switches, access points, and more for centralized management. Omada Cloud-Based Controller Gateway/Router Or 2. Add the Controller with local access or cloud access. Local Access Note: Local access applies to the Hardware Controller and Software Controller only. a. Connect your mobile device to an AP in your network. Note: If you connect to a Bridge AP, ensure you have set up it first. The default SSID on the product is isolated from service networks. b. Launch the Omada App and go to Controller Mode. Tap the + button on the upper-right corner to add the Controller. Cloud Access a. Launch the Omada App and go to Controller Mode. b. Log in with your TP-Link ID. A list of Controllers that have been Controller bound with your TP-Link ID will appear. Switch Omada Hardware/Software Controller 3. Launch the Controller, access your site, and go to the Devices page. 4. Now you can adopt and manage the APs. The Omada App is designed to help you quickly configure common settings. If you want to configure advanced settings, use the web page of your Controller. Client AP Main AP Main AP AP NVR Main AP Client AP Cameras Internet Gateway/Router Main AP Typical Application 2: Wi-Fi Extension Auto Pairing Gateway/Router Main AP Client AP AP Clients 6 Mounting At the selected site, approximately align the AP to the direction that you have oriented. Notes:

Before you start, be sure to power up and connect your devices according to the Client AP topology figure. A DHCP server (typically a gateway/router with the DHCP function enabled) is required to assign IP addresses to the APs and clients in your local network. For EAP100-Bridge, it is recommended to use PtP instead of PtMP networking. Via Web Browser 1. Connect your management device to the Main AP by using the default SSID printed on the product. Note: Under factory settings, the APs management SSID will disable after two hours upon powering on. If you need to connect to the SSID, re-power the AP. 2. Launch a web browser and enter https://omadaeap.net in the address bar. If your network doesnt have a DHCP server, ensure your management device is using IP address 192.168.0.X, then enter https://192.168.0.254 instead to access the APs web page. 3. Set up a Username and Password for secure management purpose. Then you can configure the Main AP. 4. Add the Client AP(s). For the Client AP in the same KIT as the Main AP, the system will automatically scan for it and add it to the network. For other Bridge APs, go to Bridge Network, then click Add Client AP and follow web instructions to manually add them to the network. Notes:

1. For security, we recommend changing the default login username and password of the APs. The Main APs Bridge AP list provides quick access to each APs web page. 2. If you want to change the roles of Bridge APs, use the hardware role switch on the products or refer to the User Guide at:

https://support.omadanetworks.com/product Via Omada App 1. Download and install the TP-Link Omada App from App Store or Google Play. or Scan for Omada Omada 2. Connect your mobile device to the Main AP by using the default SSID printed on the product. Note: Under factory settings, the APs management SSID will disable after two hours upon powering on. If you need to connect to the SSID, re-power the AP. 3. Open the Omada App, go to Standalone Mode > Bridge, and wait for the Bridge group to appear. Tap on the group to configure settings. Client AP Client AP Client AP Client AP Notes:

A DHCP server (typically a gateway/router with the DHCP function enabled) is required to assign IP addresses to the APs and clients in your local network. The Omada Controller must have network access to your Omada devices (the gateways/routers, switches, and APs) in order to find, adopt, and manage them. For EAP100-Bridge, it is recommended to use PtP instead of PtMP networking. Via Web Browser 1. Get an Omada Controller ready. Option 1: Omada Hardware Controller Obtain a Hardware Controller and refer to its Installation Guide to set it up. Option 2: Omada Software Controller On a PC with Windows or Linux OS, download the Software Controller from https://support.omadanetworks.com/download/software/

omada-controller/. Then run the file and follow the wizard to set up the Controller. Note: To manage your devices, the Software Controller needs to keep running on your PC. Safety Information Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Do not use the device where wireless devices are not allowed. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended. The AP can be powered only by a power adapter, a passive PoE adapter, or a PSE device (such as a PoE switch) that complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/

For AP Controller, go to the Devices page and select the desired AP to specify the channel. For web browser, go to Wireless > Wireless Settings to specify the channel. Option 3: Omada Cloud-Based Controller For 5GHz models:

Go to the Omada Portal (https://omada.tplinkcloud.com) and log in with your TP-Link ID. Then click + Add Controller to add a Cloud-Based Controller and set it up. 2. Launch the Controller, access your site, and go to the Devices page. 3. Now you can adopt and manage the APs. Note:

If you want to change the roles of Bridge APs, use the hardware role switch on the products or refer to the User Guide at:

https://support.omadanetworks.com/product Tip:

For the Omada Hardware/Software Controller, you are recommended to enable Cloud Access and bind it to your TP-Link ID. This enables you to remotely access and manage the Controller and Omada devices via the Omada Portal

(https://omada.tplinkcloud.com). Via Omada App 1. Download and install the TP-Link Omada App from App Store or Google Attention: In EU member states, EFTA countries and Northern Ireland, the operation in the frequency range 5150MHz-5350MHz is only permitted indoors. Attention: In Great Britain, the operation in the frequency range 5150MHz -

5350MHz is only permitted indoors. BE BG CH CY CZ DE EL ES FI FR HR HU LT LU LV MT IT LI AT EE IS NO PL PT RO SE SI SK UK(NI) DK IE NL UK For detailed configurations, refer to the user guides of the Controller and APs. The guides can be found at:

https://support.omadanetworks.com/product. To ask questions, find answers, and communicate with TP-Link users or engineers, please join the TP-Link Community. For technical support, the user guide and other information, please visit https://support.omadanetworks.com, or simply scan the QR code. 4. Add the Client AP(s). Play. For the Client AP in the same KIT as the Main AP, the app will automatically scan for it and add it to the network. For other Bridge APs, tap the group, then tap + and follow app instructions to manually add them to the network. Note: For security, we recommend changing the default login username and password of the APs. or Scan for Omada Omada