FCC ID: TE7WN822NV3 300Mbps High Gain Wireless USB Adapter

TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter TL-WN821N TL-WN822N TL-WN823N Rev: 4.0.0 1910010780 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand. SAR measurements are based on a 20cm spacing from the body and that compliance is achieved at that distance. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence dIndustrie Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1)cet appareil ne doit pas provoquer dinterfrences et

(2)cet appareil doit accepter toute interfrence, y compris celles susceptibles de provoquer un fonctionnement non souhait de lappareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numrique de la Classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Korea Warning Statements

NCC Notice

,

. Safety Information

When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

Dont disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

Avoid water and wet locations. This product can be used in the following countries:

AT ES LT RU BG FI LV SE BY FR MT SK CA GB NL TR CZ GR NO UA DE HU PL DK IE PT EE IT RO TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment:

Product Description: 300Mbps Wireless N USB Adapter Model No.: TL-WN821/TL-WN822N/TL-WN823N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2006/95/EC, Directives1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents:

ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011 & ETSI EN 301 489-17 V2.1.1:2009 EN 60950-1:2006+A112009+A1:2010+A12:2011 EN 62311:2008 The product carries the CE Mark:

Person responsible for marking this declaration:

Yang Hongliang Product Manager of International Business Date of issue: 2013 TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China CONTENTS Package Contents .................................................................................................... 1 Chapter 1 Product Overview ................................................................................. 2 1.1 Introduction ............................................................................................................. 2 1.2 Features.................................................................................................................. 2 1.3 Hardware Overview................................................................................................. 3 Chapter 2 Installation............................................................................................. 4 2.1 Hardware Installation .............................................................................................. 4 2.2 Software Installation................................................................................................ 4 Chapter 3 Connect to a Wireless Network ........................................................... 9 3.1 To connect using TWCU ......................................................................................... 9 3.2 To connect using WPS.......................................................................................... 13 3.2.1 PBC (Push Button Configuration) method................................................ 13 3.2.2 PIN method .............................................................................................. 15 3.3 To connect using Windows built-in wireless utility................................................. 17 In Windows 7............................................................................................ 17 In Windows Vista...................................................................................... 18 In Windows XP......................................................................................... 20 Chapter 4 Management........................................................................................ 23 4.1 Profile.................................................................................................................... 23 4.1.1 Add a profile ............................................................................................. 23 4.1.2 Modify a profile......................................................................................... 27 4.1.3 Delete a profile ......................................................................................... 28 4.2 Advanced .............................................................................................................. 28 4.3 About..................................................................................................................... 29 Chapter 5 AP Mode .............................................................................................. 30 Chapter 6 Uninstall Software............................................................................... 32 6.1 Uninstall the utility software from your PC............................................................. 32 6.2 Uninstall the driver software from your PC............................................................ 33 Appendix A: Specifications................................................................................... 34 Appendix B: Glossary............................................................................................ 35 3.3.1 3.3.2 3.3.3 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Package Contents Please verify that all the package contents below are available.

One TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter

Quick Installation Guide

One USB cable (not for TL-WN823N)

One Resource CD for TL-WN821/TL-WN822N/TL-WN823N, including:

TP-LINK Wireless Configuration Utility (TWCU) and Drivers

User Guide

Other helpful information Make sure that the above items are contained in the package. If any of the above items are damaged or missing, please contact your distributor.

Note:

The adapter mentioned in this User Guide stands for TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter without any explanation. TL-WN821N, TL-WN822N and TL-WN823N are sharing this User Guide. For simplicity, we will take TL-WN822N for example throughout this User Guide. TL-WN821N, TL-WN822N and TL-WN823N just differ in the appearance, so all figures in this User Guide are those of TL-WN822N. 1 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Chapter 1 Product Overview 1.1 Introduction The adapter is a 802.11n client device designed to deliver a high-speed and unrivaled wireless performance for your desktop. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, video streaming. With the 802.11n technology, higher throughput improvements using MIMO (multiple input, multiple output antennas), the adapters auto-sensing capability allows high packet transfer rate of up to 300Mbps for maximum throughput. It has good capability on anti-jamming, and it can also interoperate with other wireless (802.11b) products. The adapter supports WEP, WPA and WPA2 encryption to prevent outside intrusion and protect your personal information from being exposed. The adapter is easy to install and manage with the Quick Setup Wizard guiding you step-by-step through the installation process and the TP-LINK Wireless Configuration Utility instructing you to quickly set up a wireless connection. With unmatched wireless performance, reception, and security protection, the adapter is the best choice for easily adding or upgrading wireless connectivity to your desktop. 1.2 Features

Complies with IEEE 802.11n, IEEE 802.11g, IEEE 802.11b standards

Supports WPA/WPA2 data security, IEEE802.1x authentication, TKIP/AES encryption, WEP encryption

Supports high rate of up to 300Mbps for maximum throughput, supports automatically adjust to lower speeds due to distance or other operating limitations

TL-WN822N provides Mini USB interface and TL-WN821N/TL-WN823N provides USB 2.0 interface

Supports Ad Hoc and Infrastructure modes

Good capability on anti-jamming

Supports roaming between access points when configured under Infrastructure mode

Easy to configure and provides monitoring information

Supports Windows XP, Windows Vista and Windows 7

TL-WN822N provides two external antennas which are listed in a format of 2x2 for two receivers and two transmitters, and TL-WN821N/TL-WN823N provides internal antennas. 2 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 1.3 Hardware Overview LED status:

Status Off Working Status The driver has not been installed;

The adapter's radio has been disabled. Flashing Slowly The driver has been installed but no data is being transmitted or received. Flashing Quickly Data is being transmitted or received.

Note:

When the card failed to connect to a wireless network, the LED may be off. Please choose your network and try to connect again. 3 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Chapter 2 Installation 2.1 Hardware Installation 1. Locate an available USB interface on your computer. 2. Connect the adapter and your computer with the USB cable contained in the package.

Note:

The prompted Found New Hardware Wizard screen will pop up when the adapter is installed correctly. Click Cancel. 2.2 Software Installation The adapters Setup Wizard will guide you through the installation procedures for Windows 7, Windows Vista, and Windows XP. The procedures in different systems are quite similar, therefore here takes the procedures in Windows 7 for example. 1. Insert the Resource CD into your CD-ROM drive, and the window below will appear. Select model TL-WN822N. There will be a menu including: Install Driver&Utility and User Guide. Click Install Driver&Utility to begin. 4 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 2. The InstallShield Wizard window will appear. Click Next to continue. Figure 2-1 3. Choose a setup Install TP-LINK Wireless Configuration Utility and Driver. Selecting Install Driver Only will only install driver. Click Next to continue. to select type. It Figure 2-2 is recommended 5 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 4. Click Change to specify the destination location for the software or you can leave it default. Click Next in the screen below to continue. Figure 2-3 5. Click Install to continue the setup. Figure 2-4 6 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 6. The utility and drivers will install. This may take 1~2 minutes. Figure 2-5 7. After all the steps above, you will see the screen below. Click Finish to complete the setup. Figure 2-6 7 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Figure 2-7 8. After installation, the utility configuration page will automatically pop up as shown in the will appear in your system tray. To connect to a network, following figure and the icon please refer to Chapter 3 Connect to a Wireless Network. Figure 2-8 8 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Chapter 3 Connect to a Wireless Network With both the hardware and software successfully installed into your computer, you can quickly connect to a wireless network using one of the following methods.

Method One:

To connect using TWCU (TP-LINK Wireless Configuration Utility) TL-WN822N uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides you an easy interface to connect to a network and to change any settings related to the wireless adapter.

Method Two:

To connect using WPS By this method, you can connect to your network quickly on the condition that your router or access point supports QSS or WPS as is called by some other brands.

Method Three:

To connect using Windows built-in wireless utility Windows users may use the built-in wireless utility to connect to a wireless network. For specific operations, please go to To connect using Windows built-in wireless utility. 3.1 To connect using TWCU 1. After installation, the utility configuration page will automatically pop up on the screen. If the utility page does not pop up, you can also launch the utility by double-clicking on the icon on your desktop or the icon in your system tray. 2. The Network page will display all wireless networks that are available in your area. To connect to a network, simply highlight the wireless network name (SSID) and click Figure 3-1 9 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Connect. If you tick Connect automatically, the adapter will automatically connect to your target network next time. 3. You will be prompted different windows when you choose wireless network of different Figure 3-2 security types. 1) Wireless network of WPA/WPA2-Personal If you selected a wireless network of the security type WPA/WPA2-Personal, you will be prompted to enter the password in the security key field, as shown in Figure 3-3. Or you can push the WPS/QSS button on your Router (if it features the WPS/QSS function) to quickly build a connection without entering the security key (password). Figure 3-3

Note:

The security key (password) can be found on the configuration page of your Router or Access Point. 2) Wireless network of WPA/WPA2-Enterprise 10 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter If you selected a wireless network of the security type WPA/WPA2-Enterprise, you will be prompted to choose a type of authentication, either certificate or password. With Certificate as your authentication, you need to select one specific certificate from the drop-down list, as shown in Figure 3-4. With Password as your authentication, you should enter the right user name and password in the corresponding field, as shown in Figure 3-5. Figure 3-4 Figure 3-5 3) Wireless network of None If you selected a wireless network of None (that is, no security is set.), you can get directly connected to this network without any further configuration. 4. Please wait a few minutes for the connection process. 11 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 5. You have now successfully connected to your network. Click Close to enjoy the Internet. Figure 3-6 6. To view more information about the network currently connected, click Status in the tools section and the page will display information such as the network type, link quality and wireless mode. Figure 3-7 Figure 3-8 12 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 3.2 To connect using WPS WPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an existing network quickly. If the wireless router supports WPS (Wi-Fi Protected Setup) or QSS, you can establish a wireless connection between wireless card and router using either Push Button Configuration

(PBC) method or PIN method. 3.2.1 PBC (Push Button Configuration) method 1. Press the WPS/RESET button for 2~3 seconds on the back panel of the router. Here takes router TL-WR841ND for example. 2. Press the WPS button on the adapter. There are two ways:

Method One Press and hold the WPS button on the adapter directly for 2~3 seconds until 6Figure 3-11 appears.

Method Two:

Figure 3-9 Open TWCU and click WPS tab. Select Push the button on my access point or wireless router and then click Connect. 13 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 3. The adapter will be connecting to the target network. Figure 3-10 4. When the following window appears, you have successfully connected to the network. Figure 3-11 Figure 3-12 14 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 3.2.2 PIN method There are two ways to configure the WPS by PIN method:

1) Enter the PIN from your AP device. 2) Enter a PIN into your AP device. Following are detailed configuration procedures of each way. 3.2.2.1. Enter the PIN from your AP device 1. Open TWCU and click WPS tab. Select Enter the PIN of my access point or wireless router. In the empty field beside PIN, enter the PIN labeled on the bottom of the router

(here takes 13492564 for example). If you have generated a new PIN code for your router, please enter the new one instead. Click Connect to continue. 2. The adapter will be connecting to the target network. Figure 3-13 3. When Figure 3-12 appears, you have successfully connected to the network. Figure 3-14 15 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 3.2.2.2. Enter a PIN into your AP device 1. Open TWCU and click WPS tab. Select Enter the PIN of this device into my access point or wireless router. In the field beside PIN, you will see the PIN value of the adapter which is randomly generated. Click Connect to continue. 2. Open your routers Web-based Utility and click WPS link on the left of the main menu. Then click Add device and the following figure will appear. Enter the PIN value of the adapter in the empty field beside PIN and then click Connect. Figure 3-15 3. When Connect successfully appears on the screen, the WPS configuration is complete. Or you can view the adapters utility page to see whether the connection has been successful as shown in Figure 3-18. Figure 3-16 Figure 3-17 16 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 3.3 To connect using Windows built-in wireless utility Figure 3-18 3.3.1 In Windows 7 Windows 7 users may use the built-in wireless utility. Follow the steps below. 1. Left-click the wireless icon in your system tray (lower-right corner). The utility will display any available wireless networks in your area. Highlight the wireless network

(displayed using the SSID) to be connected and then click Connect. 2. If the network you would like to connect is security-enabled, enter the same security key or passphrase that is on your router. Or push the WPS/QSS buttonon the router or access Figure 3-19 17 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter point (You will be prompted to push the button on the window if WPS function is supported as shown in the figure below). If the network to be connected is not secure, the connection will be built without entering a key. 3. You have now successfully connected to the network. Figure 3-20 3.3.2 In Windows Vista Figure 3-21 Windows Vista users may use the built-in wireless utility. Follow the steps below. 1. Open the wireless utility by right-clicking on the wireless computer icon in your system tray as shown in the figure below. Select Connect to a network. 18 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect. Figure 3-22 Figure 3-23 3. If the network you would like to connect is security-enabled, enter the same security key or passphrase that is on your router. If the network to be connected is not secure, the connection will be built without entering a key. Figure 3-24 19 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 4. You have now successfully connected to the network. 3.3.3 In Windows XP Figure 3-25 Windows XP users may use the built-in wireless utility. Follow the steps below. 1. Right-click on the utility icon in your system tray (lower-right corner). Select Switch to Windows wireless configuration tool. Figure 3-26 Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-28 appears to continue. 20 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Figure 3-27 2. Right-click on the wireless computer icon in your system tray (lower-right corner). Select View Available Wireless Networks. Figure 3-28 3. The utility will display any available wireless networks in your area. Click on a network

(displayed using the SSID) and click the Connect button. Figure 3-29 21 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 4. If the network is security-enabled, you will be prompted to enter the key as shown below. If not, you will connect to the network directly without entering a key. Figure 3-30 Figure 3-31 22 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Chapter 4 Management This section will show you how to configure your TL-WN822N adapter using the TP-LINK Wireless Configuration Utility (TWCU). The TL-WN822N adapter uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides users with an easy interface to change any settings related to the adapter. Double-clicking on the icon on your desktop will start the utility. 4.1 Profile Your wireless networks may vary in different places like home, office or coffee shop. With Profile management, you can easily save and manage various networks to be connected, saving you the trouble of having to repeat the same configurations. Click Profile in the tools section, the following page will appear. 4.1.1 Add a profile Figure 4-1 To add a profile, click the Add button on the bottom of the screen. Then the configuration window will appear. If you are connecting to a wireless router or access point, select Infrastructure as the Network Type, and if you are connecting to another wireless client such as an adapter, select ad hoc as the Network Type. Then, the screen bellow will appear. Follow the instructions below to finish the setting. 23 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Figure 4-2 Figure 4-3 Figure 4-4 24 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Figure 4-5 The following items can be found on the screen. Figure 4-6

Profile Name: Enter a name for your profile (e.g. CoffeeShop, Home, Office). The same name is not allowed. Please also note that no space is allowed between words. SSID: Select the target network from the drop-down list.

Network Type: Select the network type. If you are connecting to a wireless router or access point, select Infrastructure. If you are connecting to another wireless client such as an adapter, select ad hoc. Security Type: Select the security type from the list. In Infrastructure mode, four options are available: WPA-PSK/WPA2-PSK, WPA/WPA2, WEP and None. In ad hoc mode, two options are available: WEP and None. The security type should be the same as on your router or access point, otherwise, you will not be able to build a successful connection.WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key must be the exact same key entered on your wireless router or access point. None stands for no security. In Infrastructure mode, it is recommended to enable WPA-PSK/WPA2-PSK on your wireless router or access point before configuring your 25 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter wireless adapter. While in ad hoc mode, it is recommended that you select WEP to secure your wireless network.

Note:

In Infrastructure mode, you will see Figure 4-3 if you selected the security type WEP; you will see Figure 4-4 if you selected the security type WPA-PSK/WPA2-PSK. While, if you selected the security type WPA/WPA2 (-Enterprise), Figure 4-5 or Figure 4-6 will be displayed. In ad hoc mode, you will see Figure 4-2 if you selected the security type WEP.

Encryption Type: From the drop-down menu, select the encryption type that is the same as on your router or access point.

Key Index: You can select ASCII or Hexadecimal format on the right. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.

For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters. For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters.

Security Key: Enter the passphrase exactly as it is on your wireless router or access point. Click the Show characters box to see the passphrase. Unchecking it will hide it.

Authentication: Select a type of authentication, either certificate or password.

Note:

In the security type of WPA/WPA2 (-Enterprise), you will see Figure 4-5 if you choose certificate as the authentication, you will see Figure 4-6 if you choose password as the authentication.

Certificate: If you select certificate as your Authentication, then you need to specify your certificate from the drop-down list here.

User Name: Enter the name of the enterprise network.

Password: Enter the password for the enterprise network. Click the Show characters box to see the passphrase. Unchecking it will hide it. Start this connection automatically: check this box to automatically connect to this network next time. Save: Click Save to save your settings.

Having completed the above settings, the Profile page should look like the following figure. To connect to a desired network, just highlight the network you would like to connect to and click the Connect button on the bottom of the window. Then click OK in Figure 4-8 to activate the profile. 26 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Figure 4-7 Figure 4-8 4.1.2 Modify a profile You may edit an existing profile by clicking the Modify button from the Profile page. For instance, you may like to change the profile name from Home to Home1 or you may want to specify another SSID for profile Home. After all the changes, click Save to make the changes take effect. Figure 4-9 27 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 4.1.3 Delete a profile To delete an existing profile, highlight the profile name and click Remove on the bottom of the screen or press the Delete button on your keyboard. When the following figure appears, click OK to continue. Figure 4-10 4.2 Advanced The following configurations can be made on the Advanced page:

1) To select wireless configuration tool. Here you can decide which tool to use, either the TP-LINK Configuration Utility or the Windows wireless configuration tool. (This option is available only in Windows XP.) 2) To switch to another wireless network adapter. Here you can switch to another adapter installed in your computer. The adapters successfully installed in your computer will be listed in the drop-down menu if the adapters are supported by this utility. 3) To switch to SoftAP mode. Once enabled, the adapter will be able to work as an AP. 4) To change the power save mode. Figure 4-11 28 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 4.3 About The About screen gives you information about the Driver and Utility versions of the adapter. Right-click on the icon in your system tray and select About from the list. Figure 4-12 Figure 4-13 29 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Chapter 5 AP Mode In Soft AP mode, the adapter will work as an AP. Suppose that only one computer in your house can access the Internet for various reasons like only one WLAN port is available on your wired broadband router, however, other wireless-capable devices also want to share the Internet. Then the adapter can be configured as an AP under the Soft AP mode, saving you the trouble of having to get a separate access point or a router. With this feature, a computer can use a single physical wireless adapter to connect as a client to a hardware access point while at the same time acting as a software AP allowing other wireless-capable devices to connect to it. To switch to this mode, right-click on the utility icon in your system tray and select Switch to SoftAP mode. Or from the Advanced page of the utility, tick ON under the SoftAP mode as shown in the following figure. Click OK when prompted to confirm the setting. Figure 5-1 Figure 5-2 30 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter The Soft AP icon should then appear beside Advanced icon in the utility. Figure 5-3

SoftAP mode: Select to enable or disable the function. Internet Connecting Share(ICS): Specify a connection through which devices connected to your AP can access the Internet. SSID: Enter the name for your soft AP (for example, Jone) so that others can know which AP is yours when trying to connect to it. The default name (SSID) is tp-link. Security Type: The security type here is set to be WPA2-PSK which is based on 802.11i and uses Advanced Encryption Standard instead of TKIP. It was designed to improve the security features of WEP. WPA2-PSK uses a passphrase or key to authenticate your wireless connection. You neednt make any configuration here. Encryption Type: The encryption type here is set to be AES. Security Key: Enter the Key in the field to make your AP security enabled. It is recommended that you specify another key instead of the default key 12345678. Only by entering the corresponding key can other computers establish a successful connection with your AP. IP Address: Here displays the IP address of the SoftAP. 31 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Chapter 6 Uninstall Software 6.1 Uninstall the utility software from your PC 1. On the Windows taskbar, click the Start button, click All programsTP-LINK, and then click Uninstall-TP-LINK Wireless Configuration Utility. 2. Follow the Install Shield Wizard to uninstall the utility software from your PC. Figure 6-1 Uninstall Utility 3. Click Finish when the figure below appears. Figure 6-2 32 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter 6.2 Uninstall the driver software from your PC Figure 6-3 1. On the Windows taskbar, click the Start button, click All programsTP-LINK, and then click Uninstall-300Mbps Wireless USB Adapter Driver. 2. Following the steps, then the system will uninstall the driver software of the adapter from Figure 6-4 Uninstall Driver your PC. 33 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Appendix A: Specifications Normal Interface Standards Button Operating System Throughput Radio Data Rate Modulation Mini USB Interface -TL-WN822N USB 2.0 Interface -TL-WN821N/TL-WN823N IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Wi-fi Protected Setup (WPS) Button (QSS Compatible) Windows XP, Windows Vista, Windows 7 300Mbps (Maximal) 11b: 1/2/5.5/11Mbps 11g: 6/9/12/18/24/36/48/54Mbps 11n: Up to 300Mbps 11b:CCK,QPSK,BPSK 11g:OFDM 11n: QPSK, BPSK, 16-QAM, 64-QAM Media Access Protocol CSMA/CA with ACK Data Security Frequency*

Spread Spectrum Safety & Emissions WEP; WPA/WPA2; WPA-PSK/WPA2-PSK 2.4 ~ 2.4835GHz Direct Sequence Spread Spectrum (DSSS) FCC, CE Environmental and Physical Working Temperature Storage Temperature Working Humidity Storage Humidity

~104

)

-40 ~158 0~40 (32

-40 ~70 (

10% ~ 90% RH, Non-condensing 5% ~ 90% RH, Non-condensing

)

* Only 2.412GHz~2.462GHz is allowed to be used in USA, which means only channel 1~11 is available for American users to choose. 34 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter Appendix B: Glossary

802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks.

802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security.

802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium

(EWC) was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking

(WLAN) products.

Ad hoc Network - An ad hoc network is a group of computers, each with a Wireless Adapter, connected as an independent 802.11 wireless LAN. Ad hoc wireless computers operate on a peer-to-peer basis, communicating directly with each other without the use of an access point. Ad hoc mode is also referred to as an Independent Basic Service Set (IBSS) or as peer-to-peer mode, and is useful at a departmental scale or SOHO operation.

DSSS - (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit pattern for all data transmitted. This bit pattern is called a chip (or chipping code). Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the receiver can recover the original data without the need of retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. However, to an intended receiver (i.e. another wireless LAN endpoint), the DSSS signal is recognized as the only valid signal, and interference is inherently rejected (ignored).

FHSS - (Frequency Hopping Spread Spectrum) - FHSS continuously changes (hops) the carrier frequency of a conventional carrier several times per second according to a pseudo-random set of channels. Because a fixed frequency is not used, and only the transmitter and receiver know the hop patterns, interception of FHSS is extremely difficult.

Infrastructure Network - An infrastructure network is a group of computers or other devices, each with a Wireless Adapter, connected as an 802.11 wireless LAN. In infrastructure mode, the wireless devices communicate with each other and to a wired network by first going through an access point. An infrastructure wireless network connected to a wired network is referred to as a Basic Service Set (BSS). A set of two or more BSS in a single network is referred to as an Extended Service Set (ESS). Infrastructure mode is useful at a corporation scale, or when it is necessary to connect the wired and wireless networks. 35 TL-WN821/TL-WN822N/TL-WN823N 300Mbps Wireless N USB Adapter

Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).

SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. See also Wireless Network Name and ESSID.

WEP - (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily.

Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices.

WLAN - (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area.

WPA - (Wi-Fi Protected Access) - A wireless security protocol uses TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server. 36