FCC ID: TE7WR1043NV5 450Mbps Wireless N Gigabit Router

User Guide 450Mbps Wireless N Gigabit Router TL-WR1043N REV5.0.0 1910011956 Contents About This Guide .........................................................................................................1 Chapter 1. Get to Know About Your Router . 2 1. 1. Product Overview. 3 1. 2. Appearance . 3 1. 2. 1. The Front Panel . 3 1. 2. 2. The Back Panel. 4 Chapter 2. Connect the Hardware . 6 2. 1. Position Your Router . 7 2. 2. Connect Your Router. 7 Chapter 3. Log in to Your Router. 10 Chapter 4. Set Up Internet Connection . 12 4. 1. Use Quick Setup Wizard . 13 4. 2. Manually Set up Your Internet Connection . 13 4. 3. Set Up an IPv6 Internet Connection . 17 Chapter 5. Guest Network. 21 5. 1. Create a Network for Guests . 22 5. 2. Customize Guest Network Options. 22 Chapter 6. Parental Controls . 24 Chapter 7. QoS. 28 Chapter 8. Network Security . 32 8. 1. Protect the Network from Cyber Attacks . 33 8. 2. Access Control . 34 8. 3. IP & MAC Binding . 35 Chapter 9. NAT Forwarding. 37 9. 1. Application Layer Gateway(ALG) . 38 9. 2. Share Local Resources on the Internet by Virtual Servers. 38 9. 3. Open Ports Dynamically by Port Triggering. 40 9. 4. Make Applications Free from Port Restriction by DMZ . 41 9. 5. Make Xbox Online Games Run Smoothly by UPnP . 42 Chapter 10. Customize Your Network Settings. 44 10. 1. Change the LAN Settings . 45 10. 2. Configure to Support IPTV Service. 45 10. 3. Specify DHCP Server Settings. 47 10. 4. Set Up a Dynamic DNS Service Account . 48 10. 5. Create Static Routes. 49 10. 6. Specify Wireless Settings. 51 10. 7. Use WPS for Wireless Connection . 53 10. 7. 1. Set the Routers PIN. 53 10. 7. 2. Use the WPS Wizard for Wi-Fi Connections. 53 Chapter 11. Manage the Router . 55 11. 1. Set Up System Time . 56 11. 2. Test the Network Connectivity . 57 11. 3. Upgrade the Firmware . 59 11. 3. 1. Online Upgrade . 59 11. 3. 2. Manual Upgrade . 60 11. 3. 3. Restore Interrupted Upgrade after Power Failure . 60 11. 4. Backup and Restore Configuration Settings. 61 11. 5. Change the Administrator Account. 62 11. 6. Password Recovery. 62 11. 7. Local Management . 63 11. 8. Remote Management. 64 11. 9. System Log. 65 11. 10. Monitor the Internet Traffic Statistics. 67 11. 11. Control LEDs . 68 FAQ ................................................................................................................................70 About This Guide This guide is a complement of Quick Installation Guide. The Quick Installation Guide instructs you on quick Internet setup, and this guide provides details of each function and shows you the way to configure these functions appropriate to your needs. When using this guide, please notice that features of the router may vary slightly depending on the model and software version you have, and on your location, language, and Internet service provider. All screenshots, images, parameters and descriptions documented in this guide are used for demonstration only. Conventions In this guide the following conventions are used:

Convention Underlined Teal

>

Note:

Tips:

Description Underlined words or phrases are hyperlinks. You can click to redirect to a website or a specific section. Contents to be emphasized and texts on the web page are in teal, including the menus, items, buttons, etc. The menu structures to show the path to load the corresponding page. For example, Advanced > Wireless > MAC Filtering means the MAC Filtering function page is under the Wireless menu that is located in the Advanced tab. Ignoring this type of note might result in a malfunction or damage to the device. Indicates important information that helps you make better use of your device. Symbols on the web page Click to edit the corresponding entry. Click to delete the corresponding entry. Click to enable or disable the corresponding entry. Click to view more information about items on the page. More Info The latest software, management app and utility can be found at Download Center at http://www.tp-link.com/support. The Quick Installation Guide can be found where you find this guide or inside the package of the router. Specifications can be found on the product page at http://www.tp-link.com. A Technical Support Forum is provided for you to discuss our products at http://forum.tp-link.com. Our Technical Support contact information can be found at the Contact Technical Support page at http://www.tp-link.com/support. 1 Chapter 1 Get to Know About Your Router This chapter introduces what the router can do and shows its appearance. It contains the following sections:

Product Overview Appearance 1. 1. Product Overview The TP-LINK router is designed to fully meet the need of Small Office/Home Office

(SOHO) networks and users demanding higher networking performance. The powerful antennas ensure continuous Wi-Fi signal to all your devices while boosting widespread coverage throughout your home, and the built-in Ethernet ports supply high-speed connection to your wired devices. Moreover, it is simple and convenient to set up and use the TP-LINK router due to its intuitive web interface and the powerful Tether app. 1. 2. Appearance The Front Panel 1. 2. 1. The routers LEDs (view from left to right) are located on the front panel. You can check the routers working status by following the LED Explanation table. LED Explanation Name Status On

(Power) Flashing Off Indication System initialization is complete. The system is initializing or the firmware is being upgraded. Do not disconnect or power off the router. Power is off. 3 Name

(Wi-Fi)

(Internet)

(Ethernet)

(WPS) Status On Off Blue On Orange On Off On Off On/Off Flashing Indication The wireless is working normally. The wireless is disabled. The Internet is available. The routers Internet port is connected, but the Internet is not available. The routers Internet port is not connected. The corresponding Ethernet port is connected. The corresponding Ethernet port is not connected. Turns on when WPS connection is established, and goes off about 5 minutes later. A wireless device is trying to connect to the network via WPS. This process may take up to 2 minutes. 1. 2. 2. The Back Panel Wi-Fi/WPS The routers ports (view from left to right) are located on the rear panel. Item Wi-Fi/WPS Description Press this button, and immediately press the WPS button on your device. The WPS LED of the router should change from flashing to solid on, indicating successful WPS connection. Press and hold this button for more than 2 seconds to turn on or off the wireless function of your router. 4 Item Ethernet Ports (1/2/3/4) Internet Port Power On/Off Button Power Port Reset Button Antennas Description For connecting the router to the Ethernet network devices, such as PCs, smart TVs and game consoles. For connecting to the DSL/Cable modem, or an Ethernet. Press this button to power on or off the router. For connecting the router to power socket via the provided power adapter. Press and hold this button until the Power LED blinks to reset the router to its factory default settings. Used for wireless operation and data transmit. Upright them for the best Wi-

Fi performance. 5 Chapter 2 Connect the Hardware This chapter contains the following sections:

Position Your Router Connect Your Router 2. 1. Position Your Router The product should not be located in a place where it will be exposed to moisture or excessive heat. Place the router in a location where it can be connected to multiple devices as well as to a power source. Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. The router can be placed on a shelf or desktop. Keep the router away from devices with strong electromagnetic reference, such as Bluetooth devices, cordless phones and microwaves. 2. 2. Connect Your Router Follow the steps below to connect your router. If your Internet connection is through an Ethernet cable directly from the wall instead of through a DSL / Cable / Satellite modem, connect the Ethernet cable to the routers Internet port, and then follow Step 4 and 5 to complete the hardware connection. Power adapter Router 4 Internet Power adapter Modem 1 2 3 1. Turn off the modem, and remove the backup battery if it has one. 2. Connect the modem to your routers Internet port with an Ethernet cable. 7 3. Turn on the modem, and then wait about 2 minutes for it to restart. 4. Connect the power adapter to the router and turn on the router. 5. Verify that the following LEDs are on and solid to confirm the hardware is connected correctly. Power On Wi-Fi On Internet On Note:

If the Wi-Fi LED is off, press and hold the Wi-Fi/WPS button on the rear panel for more than 2 seconds to turn it on. 6. Connect your computer to the router. Method 1: Wired Turn off the Wi-Fi on your computer and connect the devices as shown below. Ethernet cable Wi-Fi/WPS Method 2: Wirelessly 1 ) Find the SSID (Network Name) and Wireless Password printed on the label at the bottom of the router. 2 ) Click the network icon of your computer or go to Wi-Fi Settings of your smart device, and then select the SSID to join the network. Computer Smart Device TP-LINK_XXXX Connect automatically Connect

< Settings Wi-Fi Wi-Fi CHOOSE A NETWORK... OR TP-LINK_XXXX Other... Method 3: Use the WPS button Wireless devices that support WPS, including Android phones, tablets, most USB network cards, can be connected to your router through this method. Note:

WPS is not supported by iOS devices. 8 Connections are availableWireless Network Connection The WPS function cannot be configured if the wireless function of the router is disabled. Also, the WPS function will be disabled if your wireless encryption is WEP. Please make sure the wireless function is enabled and is configured with the appropriate encryption before configuring the WPS. 1 ) Tab the WPS icon on the devices screen. Here we take the Android phone for instance. 2 ) Within two minutes, press the WPS button on your router. close to Wi-Fi/WPS 9 Chapter 3 Log in to Your Router With a web-based utility, it is easy to configure and manage the router. The web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. Follow the steps below to log in to your router. 1. Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer. 2. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. The default one is admin for both username and password. Note:

If the login window does not appear, please refer to the FAQ Section. 11 Chapter 4 Set Up Internet Connection This chapter introduces how to connect your router to the Internet. The router is equipped with a web-based Quick Setup wizard. It has necessary ISP information built in, automates many of the steps and verifies that those steps have been successfully completed. Furthermore, you can also set up an IPv6 connection if your ISP provides IPv6 service. This chapter contains the following sections:

Use Quick Setup Wizard Manually Set up Your Internet Connection Set Up an IPv6 Internet Connection router. 4. 1. Use Quick Setup Wizard The Quick Setup Wizard will guide you through the process to set up your router. Tips:

If you need the IPv6 Internet connection, please refer to the section of Set Up an IPv6 Internet Connection. Follow the steps below to set up your router. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Click Quick Setup on the top of the page. Then follow the step-by-step instructions to connect your router to the Internet. Note:

During the quick setup process:

If you are not sure of the Internet Connection Type, please click Auto Detect or contact your ISP for Internet connection information. If you have changed the preset wireless network name (SSID) and wireless password, all your wireless devices must use the new SSID and password to connect to the router. 4. 2. Manually Set up Your Internet Connection In this part, you can check your current Internet connection settings. You can also modify the settings according to the service information provided by your ISP. Follow the steps below to check or modify your Internet connection settings. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Basic > Internet. 3. Select your Internet connection type from the drop-down list. Note:

If you are unsure of what your connection type is, click Auto Detect. Since different connection types need different cables and connection information, you can also refer to the demonstrations in Step 4 to determine your connection type. 4. Follow the instructions on the page to continue the configuration. Parameters on the figures are just used for demonstration. 1 ) If you choose Dynamic IP, you need to select whether to clone the MAC address. Dynamic IP users are usually equipped with a cable TV or fiber cable. 13 2 ) If you choose Static IP, enter the information provided by your ISP in the corresponding fields. 3 ) If you choose PPPoE, enter the username and password provided by your ISP. PPPoE users usually have DSL cable modems. 14 4 ) If you choose L2TP, enter the username and password and choose the Secondary Connection provided by your ISP. Different parameters are needed according to the Secondary Connection you have chosen. 5 ) If you choose PPTP, enter the username and password, and choose the Secondary Connection provided by your ISP. Different parameters are needed according to the Secondary Connection you have chosen. 15 5. Click Save. Note:

It may take 1-2 minutes to make the settings valid. 6. After the connection succeeds, the screen will display as follows. Here we take PPPoE as an example. 16 Tips:

If your Internet connection type is BigPond Cable, please go to Advanced > Network > Internet to set your router. If you use Dynamic IP and PPPoE and you are provided with any other parameters that are not required on the page, please go to Advanced > Network > Internet to complete the configuration. If you still cannot access the Internet, refer to the FAQ for further instructions. 4. 3. Set Up an IPv6 Internet Connection Your ISP provides information about one of the following IPv6 Internet connection types:

PPPoE, Dynamic IP(SLAAC/DHCPv6), Static IP, 6to4 tunnel, Pass-Through (Bridge). 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > IPv6. 3. Enable IPv6 and select the Internet connection type provided by your ISP. Tips:

If you do not know what your Internet connection type is, contact your ISP or judge according to the already known information provided by your ISP. 4. Fill in information as required by different connection types. Red blanks must be filled router. in. 1 ) Static IP: Fill in blanks and click Save. 2 ) Dynamic IP(SLAAC/DHCPv6): Click Advanced to input further information if your ISP requires. Click Save and then click Renew. 17 3 ) PPPoE: By default, the router uses the IPv4 account to connect to the IPv6 server. Click Advanced to input further information if your ISP requires. Click Save and then click Connect. Note:

If your ISP provides two separate accounts for the IPv4 and IPv6 connections, please uncheck the box for Use the same session with IPv4 connection and manually enter the username and password for the IPv6 connection. 4 ) 6to4 Tunnel: An IPv4 Internet connection type is a prerequisite for this connection type (Manually Set up Your Internet Connection). Click Advanced to input further information if your ISP requires. Click Save and then click Connect. 18 5 ) Pass-Through (Bridge): Click Save and skip to step 6. 5. Configure LAN ports. Windows users are recommended to choose from the first two types. Fill in Address Prefix provided by your ISP, and click Save. Tips:

Find Help on the management interface to know more about items. 6. Click Status to check whether you have successfully set up an IPv6 connection. The following figure is an example of a successful PPPoE configuration. 19 Tips:

Visit the FAQ if there is no Internet connection. 20 Chapter 5 Guest Network This function allows you to provide Wi-Fi access for guests without disclosing your main network. When you have guests in your house, apartment, or workplace, you can create a guest network for them. In addition, you can customize guest network options to ensure network security and privacy. This chapter contains the following sections:

Create a Network for Guests Customize Guest Network Options 5. 1. Create a Network for Guests 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Guest Network. Locate the Wireless section. 3. Create a guest network as needed. 1 ) Enable Guest network. 2 ) Customize the SSID. Do not select Hide SSID unless you want your guests to manually input the SSID for guest network access. 3 ) Select the Security type. If No security is selected, no password is needed to access your guest network. If WAP/WPA2-Personal is selected, keep the default Version and Encryption values, and customize your own password. 4. Click Save. Now your guests can access your guest network using the SSID and password you set!

Tips:

To view guest network information, go to Advanced > Status and locate the Guest Network section. 5. 2. Customize Guest Network Options 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Guest Network. Locate the Settings section. 3. Customize guest network options according to your needs. 22 Allow guests to see each other Check this box if you want to allow the wireless clients on your guest network to communicate with each other via methods such as network neighbors and Ping. Allow guests to access my local network Check this box if you want to allow the wireless clients on your guest network to communicate with the devices connected to your routers LAN ports or main network via methods such as network neighbors and Ping. 4. Click Save. Now you can ensure network security and privacy!

Tips:

To view guest network information, go to Advanced > Status and locate the Guest Network section. 23 Chapter 6 Parental Controls This function allows you to block inappropriate, explicit and malicious websites, and control access to specified websites at specified time. I want to:

I want How can I do that?

Control the times of day my children or other home network users are allowed to access the Internet and even types of websites they can visit. For example, I want to allow my childrens devices (e.g. a computer or a tablet) to access only www.tp-link.com and Wikipedia.org from 18:00 (6PM) to 22:00 (10PM) at the weekend and not other times. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Parental Controls and enable Parental Controls. 3. Click Add. And then Click View Existing Devices, and select the access device. Or, input the Device Name and MAC Address manually. 4. Click the icon to set the Internet Access Time. Drag the cursor over the appropriate cell(s) and click OK. 25 5. Enter a Description for the entry, check the box for Enable This Entry, and then click OK. 6. Select Whitelist as the restriction policy. Tips:

With Blacklist selected, the controlled devices cannot access any websites containing the specified keywords during the Internet Access Time period. With Whitelist selected, the controlled devices can only access websites containing the specified keywords during the Internet Access Time period. 7. Click

. Enter a website and click Save. You can add up to 32 keywords for either Blacklist or Whitelist. Below are some sample entries to allow access. For Whitelist: Enter a web address (e.g. wikipedia.org) to allow access only to its related websites. If you wish to block all Internet browsing access, do not add any keyword to the Whitelist. For Blacklist: Specify a web address (e.g. wikipedia.org), a web address keyword (e.g. wikipedia) or a domain suffix (eg. edu or .org) to block access only to the websites containing that keyword or suffix. 26 Done!

Now you can control your childrens Internet access as needed. 27 Chapter 7 QoS This chapter introduces how to create a QoS (Quality of Service) rule to specify prioritization of traffic and minimize the impact caused when the connection is under heavy load. How can I do that?

QoS (Quality of Service) is designed to ensure the efficient operation of the network when come across network overload or congestion. I want to:

Specify priority levels for some devices or applications. For example, I have several devices that are connected to my wireless network. I would like to set an intermediate speed on the Internet for my phone. 1. Enable QoS and set bandwidth allocation. 1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2 ) Go to Advanced > QoS. 3 ) Select Enable QoS. 4 ) Input the maximum upload and download bandwidth provided by your Internet service provider. 1Mbps equal s to 1000Kbps. 5 ) Click Advanced and drag the scroll bar to set the bandwidth priority percentage. 6 ) Click Save. 2. Add a middle priority QoS rule for the phone. 1 ) Click Add in Qos Rule List section. 29 2 ) Click View Existing Devices. 3 ) Choose the respective device from the list. 4 ) Click OK. 3. Refer to the steps above to apply other QoS rules if any. Note:

If you want to delete a QoS rule, click the list. to remove the responding rule from 30 Done!

Now QoS is implemented to prioritize Internet traffic. 31 Chapter 8 Network Security This chapter guides you on how to protect your home network from cyber attacks and unauthorized users by implementing these three network security functions. You can protect your home network against DoS (Denial of Service) attacks from flooding your network with server requests using DoS Protection, block or allow specific client devices to access your network using Access Control, or you can prevent ARP spoofing and ARP attacks using IP & MAC Binding. This chapter contains the following sections:

Protect the Network from Cyber Attacks Access Control IP & MAC Binding 8. 1. Protect the Network from Cyber Attacks The SPI (Stateful Packet Inspection) Firewall and DoS (Denial of Service) Protection protect the router from cyber attacks. The SPI Firewall can prevent cyber attacks and validate the traffic that is passing through the router based on the protocol. This function is enabled by default, and its recommended to keep the default settings. DoS Protection can protect your home network against DoS attacks from flooding your network with server requests. Follow the steps below to configure DoS Protection. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Security > Settings. 3. Enable DoS Protection. 4. Set the level (Off, Low, Middle or High) of protection for ICMP-FLOOD Attack Filtering, UDP-FlOOD Attack Filtering and TCP-SYN-FLOOD Attack Filtering. ICMP-FLOOD Attack Filtering - Enable to prevent the ICMP (Internet Control Message Protocol) flood attack. UDP-FlOOD Attack Filtering - Enable to prevent the UDP (User Datagram Protocol) flood attack. TCP-SYN-FLOOD Attack Filtering - Enable to prevent the TCP-SYN (Transmission Control Protocol-Synchronize) flood attack. Tips:

The level of protection is based on the number of traffic packets. The protection will be triggered immediately when the number of packets exceeds the preset threshold value (the value can be set on Advanced > System Tools > System Parameters > DoS Protection Level Settings), and the vicious host will be displayed in the Blocked DoS Host List. 33 5. If you want to ignore the ping packets from the WAN port, select Ignore Ping Packet From WAN Port; if you want to ignore the ping packets form the LAN port, select Ignore Ping Packet From LAN Port. 6. Click Save. 8. 2. Access Control Access Control is used to block or allow specific client devices to access your network

(via wired or wireless) based on a list of blocked devices (Blacklist) or a list of allowed devices (Whitelist). I want to:

Block or allow specific client devices to access my network (via wired or wireless). 1. Visit http://tplinkwifi.net, and log in with the username and How can I do that?

password you set for the router. 2. Go to Advanced > Security > Access Control. 3. Enable Access Control. 4. Select the access mode to either block (recommended) or allow the device(s) in the list. To block specific device(s) 1 ) Select Blacklist and click Save. 2 ) Select the device(s) to be blocked in the Online Devices table by ticking the box. 34 3 ) Click Block above the Online Devices table. The selected devices will be added to Devices in Blacklist automatically. To allow specific device(s) 1 ) Select Whitelist and click Save. 2 ) Click Add in the Devices in Whitelist section. Enter the Device Name and MAC Address (You can copy and paste the information from the Online Devices list if the device is connected to your network). Done!

3 ) Click OK. Now you can block or allow specific client devices to access your network (via wired or wireless) using the Blacklist or Whitelist. IP & MAC Binding 8. 3. IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind network devices IP address to its MAC address. This will prevent ARP Spoofing and other ARP attacks by denying network access to an device with matching IP address in the Binding list, but unrecognized MAC address. 35 I want to:

How can I do that?

Done!

Prevent ARP spoofing and ARP attacks. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Security > IP & MAC Binding. 3. Enable ARP Binding. 4. Bind your device(s) according to your need. To bind the connected device(s):

Click To bind the unconnected device 1 ) Click Add in the Binding List section. to add the corresponding device to the Binding List. 2 ) Enter the MAC address and IP address that you want to bind. Enter a Description for this binding entry. 3 ) Check the box for Enable This Entry and click OK. Now you dont need to worry about ARP spoofing and ARP attacks!

36 Chapter 9 NAT Forwarding The routers NAT (Network Address Translation) feature makes devices on the LAN use the same public IP address to communicate with devices on the Internet, which protects the local network by hiding IP addresses of the devices. However, it also brings about the problem that an external host cannot initiatively communicate with a specified device on the local network. With the forwarding feature the router can penetrate the isolation of NAT and allows devices on the Internet to initiatively communicate with devices on the local network, thus realizing some special functions. The TP-LINK router supports four forwarding rules. If two or more rules are set, the priority of implementation from high to low is Virtual Servers, Port Triggering, UPNP and DMZ. This chapter contains the following sections:

Application Layer Gateway(ALG) Share Local Resources on the Internet by Virtual Servers Open Ports Dynamically by Port Triggering Make Applications Free from Port Restriction by DMZ Make Xbox Online Games Run Smoothly by UPnP 9. 1. Application Layer Gateway(ALG) Application Layer Gateway (ALG) allows customized Network Address Translation(NAT) traversal filters to be plugged into the gate way to support address and port translation for certain application layer control/data protocols: FTP, TFTP, H323 and more. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > NAT Forwarding > ALG. All types of ALG functions are enabled by default. You can Enable or disable them as needed. 9. 2. Share Local Resources on the Internet by Virtual Servers When you build up a server on the local network and want to share it on the Internet, Virtual Servers can realize the service and provide it to Internet users. At the same time Virtual Servers can keep the local network safe as other services are still invisible from the Internet. Virtual Servers can be used for setting up public services on your local network, such as HTTP, FTP, DNS, POP3/SMTP and Telnet. Different services use different service ports. Port 80 is used in HTTP service, port 21 in FTP service, port 25 in SMTP service and port 110 in POP3 service. Please verify the service port number before the configuration. I want to:

Share my personal website Ive built in local network with my friends through the Internet. For example, the personal website has been built on my home PC (192.168.0.100). I hope that my friends on the Internet can 38 visit my website in some way. The PC is connected to the router with the WAN IP address 218.18.232.154. Personal Website Router Home LAN WAN: 218.18.232.154 INTERNET 1. Assign a static 192.168.0.100. IP address to your PC, for example 2. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3. Go to Advanced > NAT Forwarding > Virtual Servers. 4. Click Add. Click View Existing Services and select HTTP. The External Port, Internal Port and Protocol will be automatically filled in. Enter the PCs IP address 192.168.0.100 in the Internal IP field. 5. Click OK. Tips:

It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which port and protocol to use. If the service you want to use is not in the Service Type, you can enter the corresponding parameters manually. You should verify the port number that the service needs. You can add multiple virtual server rules if you want to provide several services in a router. Please note that the External Port should not be overlapped. Users on the Internet can enter http:// WAN IP (in this example:

39 How can I do that?

Done!

IP should be a public ISP, http:// 218.18.232.154) to visit your personal website. Tips:

The WAN is to apply assigned dynamically by and register a domain name for the WAN referring to Set Up a Dynamic DNS Service Account. Then users on the Internet can use http:// domain name to visit the website. If you have changed the default External Port, you should use http:// WAN IP: External Port or http:// domain name: External Port to visit the website. IP address. For the WAN it is recommended the IP 9. 3. Open Ports Dynamically by Port Triggering Port Triggering can specify a triggering port and its corresponding external ports. When a host on the local network initiates a connection to the triggering port, all the external ports will be opened for subsequent connections. The router can record the IP address of the host. When the data from the Internet return to the external ports, the router can forward them to the corresponding host. Port Triggering is mainly applied to online games, VoIPs, video players and common applications including MSN Gaming Zone, Dialpad and Quick Time 4 players, etc. Follow the steps below to configure the Port Triggering rules:

1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > NAT Forwarding > Port Triggering and click Add. 3. Click View Existing Applications, and select the desired application. The External Port, Internal Port and Protocol will be automatically filled in. The following picture takes application MSN Gaming Zone as an example. router. 4. Click OK. 40 Tips:

You can add multiple port triggering rules according to your network need. The triggering ports can not be overlapped. If the application you need is not listed in the Existing Applications list, please enter the parameters manually. You should verify the external ports the application uses first and enter them into External Port field according to the format the page displays. 9. 4. Make Applications Free from Port Restriction by DMZ When a PC is set to be a DMZ (Demilitarized Zone) host on the local network, it is totally exposed to the Internet, which can realize the unlimited bidirectional communication between internal hosts and external hosts. The DMZ host becomes a virtual server with all ports opened. When you are not clear about which ports to open in some special applications, such as IP camera and database software, you can set the PC to be a DMZ host. 41 Note:

When DMZ is enabled, the DMZ host is totally exposed to the Internet, which may bring some potential safety hazards. If DMZ is not in use, please disable it in time. I want to:

Make the home PC join the Internet online game without port restriction. For example, due to some port restriction, when playing the online games, you can login normally but cannot join a team with other players. To solve this problem, set your PC as a DMZ host with all ports open. 1. Assign a static IP address to your PC, for example 192.168.0.100. 2. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3. Go to Advanced > NAT Forwarding > DMZ and select Enable 4. Enter the IP address 192.168.0.100 in the DMZ Host IP DMZ. Address filed. How can I do that?

Done!

5. Click Save. The configuration is completed. Youve set your PC to a DMZ host and now you can make a team to game with other players. 9. 5. Make Xbox Online Games Run Smoothly by UPnP The UPnP (Universal Plug and Play) protocol allows applications or host devices to automatically find the front-end NAT device and send request to it to open the corresponding ports. With UPnP enabled, the applications or host devices on the local network and the Internet can freely communicate with each other thus realizing the seamless connection of the network. You may need to enable the UPnP if you want to use applications for multiplayer gaming, peer-to-peer connections, real-time communication (such as VoIP or telephone conference) or remote assistance and more. 42 Tips:

UPnP is enabled by default in this router. Only the application supporting UPnP protocol can use this feature. UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of operating system need to install the UPnP components). For example, when you connect your Xbox to the router which has connected to the Internet to play online games, UPnP will send request to the router to open the corresponding ports allowing the following data penetrating the NAT to transmit. Therefore, you can play Xbox online games without a hitch. LAN WAN INTERNET XBOX Router If necessary, you can follow the steps to change the status of UPnP. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > NAT Forwarding > UPnP and toggle on or off according to your router. needs. 43 Chapter 10 Customize Your Network Settings This chapter guides you on how to configure advanced network features. This chapter contains the following sections:

Change the LAN Settings Configure to Support IPTV Service Specify DHCP Server Settings Set Up a Dynamic DNS Service Account Create Static Routes Specify Wireless Settings Use WPS for Wireless Connection 10. 1. Change the LAN Settings The router is preset with a default LAN IP 192.168.0.1, which you can use to log in to its web management page. The LAN IP address together with the Subnet Mask also defines the subnet that the connected devices are on. If the IP address conflicts with another device on your local network or your network requires a specific IP subnet, you can change it. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > Network > LAN. 3. Type in a new IP Address appropriate to your needs. And leave the Subnet Mask as the default settings. router. 4. Click Save. Note:

If you have set the Virtual Server, DMZ or DHCP address reservation, and the new LAN IP address is not in the same subnet with the old one, then you should reconfigure these features. 10. 2. Configure to Support IPTV Service I want to:

Configure IPTV setup to enable Internet/IPTV/Phone service provided by my Internet Service Provider (ISP). 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Network > IPTV. 3. If your ISP provides the networking service based on IGMP technology, e.g., British Telecom(BT) and Talk Talk in UK:

1 ) Check the box for IGMP Proxy and select the IGMP Version, either V2 or V3, as required by your ISP. How can I do that?

45 2 ) Click Save. 3 ) After configuring IGMP proxy, IPTV can work behind your router now. You can connect your set-top box to any of the routers Ethernet port. If IGMP is not the technology your ISP applies to provide IPTV service:

1 ) Tick Enable IPTV. 2 ) Select the appropriate Mode according to your ISP. Select Bridge if your ISP is not listed and no other parameters are required. Select Custom if your ISP is not listed but provides necessary parameters. 3 ) After you have selected a mode, the necessary parameters, including the LAN port for IPTV connection, are predetermined. If not, select the LAN type to determine which port is used to support IPTV service. 4 ) Click Save. 5 ) Connect the set-top box to the corresponding LAN port which is predetermined or you have specified in Step 3. Your IPTV setup is done now! You may need to configure your set-top box before enjoying your TV. Tips:

Qos and IPTV cannot be enabled at the same time. Done!

46 10. 3. Specify DHCP Server Settings By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP Address Pool. You can change the settings of the DHCP Server if necessary, and you can reserve LAN IP addresses for specified client devices. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > Network > DHCP Server. To specify the IP address that the router assigns:

1. Check the box for Enable DHCP Server. 2. Enter the starting and ending IP addresses in the IP Address Pool. 3. Enter other parameters if the ISP offers. The Default Gateway is automatically filled in and is the same as the LAN IP address of the router. 4. Click Save. To reserve an IP address for a specified client device:

1. Click Add in the Address Reservation section. 47 2. Click View Exsiting Devices or enter the MAC address of the client device. 3. Enter the IP address to reserve for the client device. 4. Enter the Description for this entry. 5. Check the box for Enable This Entry and click OK. 10. 4. Set Up a Dynamic DNS Service Account Most ISPs assign a dynamic IP address to the router and you can use this IP address to access your router remotely. However, the IP address can change any time and you dont know when it changes. In this case, you might apply the DDNS (Dynamic Domain Name Server) feature on the router to allow you and your friends to access your router and local servers (FTP, HTTP, etc.) using domain name without checking and remembering the IP address. Note:

DDNS does not work if the ISP assigns a private WAN IP address (such as 192.168.1.x) to the router. To set up DDNS, please follow the instructions below:

1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > Network > Dynamic DNS. 3. Select the DDNS Service Provider (NO-IP or DynDNS). If you dont have a DDNS account, select a service provider and click Go to register. router. 48 4. Enter the username, password and domain name of the account. 5. Click Login and Save. Tips:

If you want to use a new DDNS account, please logout first, and then login with the new account. 10. 5. Create Static Routes Static routing is a form of routing that is configured manually by a network administrator or a user by adding entries into a routing table. The manually-configured routing information guides the router in forwarding data packets to the specific destination. I want to:

Visit multiple networks and servers at the same time. For example, in a small office, my PC can surf the Internet through Router A, but I also want to visit my companys network. Now I have a switch and Router B. I connect the devices as shown in the following figure so that the physical connection between my PC and my companys server is established. To surf the Internet and visit my companys network at the same time, I need to configure the static routing. 49 Router A Router B Companys server LAN: 192.168.0.1 LAN: 192.168.0.2 172.30.30.1 WAN: 172.30.30.100 Switch 192.168.0.100 PC How can I do that?

1. Change the routers LAN IP addresses to two different IP addresses on the same subnet. Disable Router Bs DHCP function. 2. Visit http://tplinkwifi.net, and log in with the username and password you set for Router A. 3. Go to Network > Advanced Routing. 4. Click Add and finish the settings according to the following explanations:

Network Destination: The destination IP address that you want to assign to a static route. This IP address cannot be on the same subnet with the WAN IP or LAN IP of Router A. In the example, the IP address of the company network is the destination IP address, so here enter 172.30.30.1. Subnet Mask: Determines the destination network with the 50 destination IP address. If the destination is a single IP address, enter 255.255.255.255; otherwise, enter the subnet mask of the corresponding network IP. In the example, the destination network is a single IP, so here enter 255.255.255.255. Default Gateway: The IP address of the gateway device to which the data packets will be sent. This IP address must be on the same subnet with the routers IP which sends out data. In the example, the data packets will be sent to the LAN port of Router B and then to the Server, so the default gateway should be 192.168.0.2. Interface: Determined by the port (WAN/LAN) that sends out data packets. In the example, the data are sent to the gateway through the LAN port of Router A, so LAN should be selected. Description: Enter a description for this static routing entry. 5. Click OK. 6. Check the System Routing Table below. If you can find the entry youve set, the static routing is set successfully. Done!

Open a web browser on your PC. Enter the company servers IP address to visit the company network. 10. 6. Specify Wireless Settings The routers wireless network name (SSID) and password, and security option are preset in the factory. The preset SSID and password can be found on the label of the router. You can customize the wireless settings according to your needs. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. To enable or disable the wireless function:

1. Go to Basic > Wireless. 2. The wireless radio is enabled by default. If you want to disable the wireless function of the router, just uncheck the box for Enable Wireless Radio. In this case, all the wireless settings will be invalid. 51 To change the wireless network name (SSID) and wireless password:

1. Go to Basic > Wireless. 2. Create a new SSID in Network Name (SSID) and customize the password for the network in Password. The value is case-sensitive. Note:

If you change the wireless settings with a wireless device, you will be disconnected when the settings are effective. Please write down the new SSID and password for future use. To hide SSID:

1. Go to Basic > Wireless. 2. Select Hide SSID, and your SSID wont display when you scan for local wireless networks on your wireless device and you need to manually join the network. To change the security option:

1. Go to Advanced > Wireless > Wireless Settings. 2. Select an option from the Security drop-down list. We recommend you dont change the default settings unless necessary. If you select other options, configure the related parameters according to the help page. In addition Mode - Select a transmission mode according to your wireless client devices. It is recommended to just leave it as default. Channel Width - Select a channel width (bandwidth) for the wireless network. 52 Channel - Select an operating channel for the wireless network. It is recommended to leave the channel to Auto, if you are not experiencing the intermittent wireless connection issue. Transmit Power - Select either High, Middle or Low to specify the data transmit power. The default and recommended setting is High. 10. 7. Use WPS for Wireless Connection Wi-Fi Protected Setup (WPS) provides an easier approach to set up a security-protected Wi-Fi connection. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > Wireless > WPS . 10. 7. 1. Set the Routers PIN Routers PIN is enabled by default to allow wireless devices to connect to the router using the PIN. You can use the default one or generate a new one. router. Note:

If you want to enable/disable the WPS feature, go to System Tools > System Parameters > WPS, check or uncheck the box for Enable WPS. PIN (Personal Identification Number) is an eight-character identification number preset to each router. WPS supported devices can connect to your router with the PIN. The default PIN is printed on the label of the router. 10. 7. 2. Use the WPS Wizard for Wi-Fi Connections 1. Select a setup method:

Push Button(Recommended): Click Connect on the screen. Within two minutes, press the WPS button on the client device. PIN: Enter the clients PIN, and click Connect. 53 2. Success will appear on the above screen and the WPS LED on the router will keep on for five minutes if the client has been successfully added to the network. 54 Chapter 11 Manage the Router This chapter shows you the configuration for managing and maintaining your router. It includes the following sections:

Set Up System Time Test the Network Connectivity Upgrade the Firmware Backup and Restore Configuration Settings Change the Administrator Account Password Recovery Local Management Remote Management System Log Monitor the Internet Traffic Statistics Control LEDs 11. 1. Set Up System Time System time is the time displayed while the router is running. The system time you configure here will be used for other time-based functions like Parental Controls. You can choose the way to obtain the system time as needed. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > System Tools > Time Settings. To get time from the Internet:

1. In the Set Time field, select Get automatically from the Internet. 2. Select your local Time Zone from the drop-down list. 3. In the NTP Server I fileld, enter the IP address or domain name of your desired NTP 4. (Optional) In the NTP Server II fileld, enter the IP address or domain name of the Server. second NTP Server. 5. Click Obtain to get the current Internet time and click Save. To manually set the date and time:

1. In the Set Time field, select Manually. 56 2. Set the current Date (In MM/DD/YYYY format). 3. Set the current Time (In HH/MM/SS format). 4. Click Save. To set up Daylight Saving Time:

1. Select Enable Daylight Saving Time. 2. Select the correct Start date and time when daylight saving time starts at your local time zone. 3. Select the correct End date and time when daylight saving time ends at your local time zone. 4. Click Save. 11. 2. Test the Network Connectivity Diagnostics is used to test the connectivity between the router and the host or other network devices. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > System Tools > Diagnostics. 57 3. Enter the information with the help of page tips:

1 ) Choose Ping or Traceroute as the diagnostic tool to test the connectivity;

Ping is used to test the connectivity between the router and the tested host, and measure the round-trip time. Traceroute is used to display the route (path) your router has passed to reach the tested host, and measure transit delays of packets across an Internet Protocol network. 2 ) Enter the IP Address or Domain Name of the tested host. 4. Click Start to begin the diagnostics. Tips:

Click Advanced, you can modify the ping count, ping packet size or the Traceroute Max TTL. Its recommended to keep the default value. The figure below indicates the proper connection between the router and the Yahoo server (www.Yahoo.com) tested through Ping. The figure below indicates the proper connection between the router and the Yahoo server (www.Yahoo.com) tested through Traceroute. 58 11. 3. Upgrade the Firmware TP-LINK aims at providing better network experience for users. We will inform you throught the web management page if theres any update firmware available for your router. Also, the latest firmware will be released at the TP-LINK official website www.tp-link.com, and you can download it from the Support page for free. Note:

Make sure you remove all attached USB devices from the router before the firmware upgrade to prevent data loss. Backup your router configuration before firmware upgrade. Do NOT turn off the router during the firmware upgrade. 11. 3. 1. Online Upgrade 1. Visit http://tplinkwifi.net, and log in with the username and password youve set for the router. 2. When the latest firmware is available for your router, the update icon will display in the top-right corner of the page. Click the icon to go to the Firmware Upgrade page. Alternatively, you can go to Advanced > System Tools > Firmware Upgrade, and click Check for upgrade to see whether the latest firmware is released. 3. Focus on the Online Upgrade section, and click Upgrade. 4. Wait a few minutes for the upgrade and reboot to complete. Tips:

If theres a new and important firmware update for your router, you will see the notification (similar as shown below) on your computer as long as a web browser is opened. Click Upgrade now, and log into the web management page with the username and password you set for the router. You will see the Firmware Upgrade page. 59 router. 11. 3. 2. Manual Upgrade 1. Download the latest firmware file for the router from www.tp-link.com. 2. Visit http://tplinkwifi.net, and log in with the username and password you set for the 3. Go to Advanced > System Tools > Firmware Upgrade. 4. Focus on the Device Information section. Make sure the downloaded firmware file is matched with the Hardware Version. firmware file, and click Upgrade. 5. Focus on the Manual Upgrade section. Click Browse to locate the downloaded new 6. Wait a few minutes for the upgrade and reboot to complete. 11. 3. 3. Restore Interrupted Upgrade after Power Failure If your router cannot start up after an upgrade interruption due to power failure, follow the steps below to restore the interrupted upgrade. Otherwise, your router cannot work again. 1. Make sure you have the latest firmware file in your computer. If not, try another way to connect your computer to the Internet and download the latest firmware file from www.tp-link.com. 2. Connect your computer to the router with an Ethernet cable. 3. Visit 192.168.0.1 and you will see the following upgrade page. 60 4. Click Browse and select the downloaded firmware file. 5. Click Upgrade and wait for a few minutes until the router completes the upgrading and restarts. 11. 4. Backup and Restore Configuration Settings The configuration settings are stored as a configuration file in the router. You can backup the configuration file to your computer for future use and restore the router to a previous settings from the backup file when needed. Moreover, if necessary you can erase the current settings and reset the router to the default factory settings. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > System Tools > Backup & Restore. To backup configuration settings:

Click Backup to save a copy of the current settings to your local computer. A .bin file of the current settings will be stored to your computer. router. To restore configuration settings:

1. Click Browse to locate the backup configuration file stored on your computer, and click Restore. 2. Wait a few minutes for the restoring and rebooting. Note: During the restoring process, do not turn off or reset the router. To reset the router to factory default settings:

1. Click Factory Restore to reset the router. 61 2. Wait a few minutes for the resetting and rebooting. Note:

During the resetting process, do not turn off or reset the router. We strongly recommend you backup the current configuration settings before resetting the router. 11. 5. Change the Administrator Account The account management feature allows you to change your login username and password of the web management page. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > System Tools > Administration and focus on the Account router. Management section. 3. Enter the old username and old password, then a new username and a new password twice (both case-sensitive). Click Save. 4. Use the new username and password for the following logins. 11. 6. Password Recovery This feature allows you to recover your default login username and password in case you forget them. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 62 2. Go to Advanced > System Tools > Administration and focus on the Password Recovery section. 3. Check the box for Enable Password Recovery. 4. Specify a mailbox (From) for sending the recovery letter and enter its SMTP Server address. Specify a mailbox (To) for receiving the recovery letter. If the mailbox (From) to send the recovery letter requires encryption, select Enable Authentication and enter its username and password. Tips:

SMTP server is available for users in most webmail systems. For example, the SMTP server address of Gmail is smtp.gmail.com. You can refer to their Help page to learn the SMTP server address. Generally, Enable Authentication should be selected if the login of the mailbox requires username and password. 5. Click Save. You can click Test Email to test whether the configuration is successful. To recover the default login username and password, please refer to FAQ. 11. 7. Local Management This feature allows you to limit the number of client devices on your LAN from accessing the router by using the MAC address-based authentication. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > System Tools > Administration and complete the settings In Local Management section according to your needs. Allow all LAN connected devices to manage the router:

Toggle on Access for All LAN Connected Devices. router. 63 Allow specific devices to manage the router:

1 ) Toggle off Access for All LAN Connected Devices. 2 ) Click Add. 3 ) Click View Existing Devices and select the device to manage the router from the Existing Devices list, or enter the MAC address of the device manually. 4 ) Specify a Description for this entry. 5 ) Check the box for Enable This Entry. 6 ) Click OK. 11. 8. Remote Management This feature allows you to control remote devices authority to manage the router. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the 2. Go to Advanced > System Tools > Administration and complete the settings in Remote Management section according to your needs. router. 64 Forbid all devices to manage the router remotely: Select Disable Remote Management and click Save. Allow all devices to manage the router remotely:

1 ) Select Enable Remote Management for All Devices. 2 ) Enter Web Management Port (1024-65535 or 80). 3 ) Click Save. Devices on the Internet can log in to http://Routers WAN IP address:port number (such as http://113.116.60.229:1024) to manage the router. Tips:

You can find the WAN IP address of the router on Basic > Network Maps > Internet. The routers WAN IP is usually a dynamic IP. Please refer to Set Up a Dynamic DNS Service Account if you want to log in to the router through a domain name. Allow specific devices to manage the router remotely:

1 ) Select Enable Remote Management for Specified Devices. 2 ) Enter Web Management Port (1024-65535 or 80). 3 ) In Remote Management IP address, enter the IP address of the remote device to manage the router. 4 ) Click Save. Devices using this WAN IP can manage the router by logging in to http://Routers WAN IP:port number (such as http://113.116.60.229:1024). Tips:

The routers WAN IP is usually a dynamic IP. Please refer to Set Up a Dynamic DNS Service Account if you want to log in to the router through a domain name. 11. 9. System Log When the router does not work properly, you can save the system log and send it to the technical support for troubleshooting. To Save the System Log in Local:

65 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > System Tools > System Log. 3. Choose the type and level of the system logs according to your need. 4. Click Save Log to save the system logs to local. To Send the System Log to a Mailbox at a Fixed Time:

For example, I want to check my routers working status at a fixed time every day, however, its too troublesome to log in to the web interface every time I want to go checking. It would be great if the system logs could be sent to my mailbox at 8 a.m. every day. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > System Tools > System Log. 3. Click Mail Settings. 4. Enter the information with the help of page tips:

66 1 ) From: Enter the email address used for sending the system log. 2 ) To: Enter the recipients email address, which can be the same as or different from the senders email address. 3 ) SMTP Server: Enter the SMTP server address. Tips: SMTP server is available for users in most webmail systems. For example, the SMTP server address of Hotmail is smtp-mail.outlook.com. You can refer to their Help page to learn the SMTP server address. 4 ) Select Enable Authentication. Tips: Generally, Enable Authentication should be selected if the login of the mailbox requires username and password. 5 ) Username: Enter the email address used for sending the system log. 6 ) Password: Enter the password to login the senders email address. 7 ) Select Enable Auto Mail. Tips: The router will send the system log to the designated email address if this option is enabled. 8 ) Set a fixed time. The recipient will receive the system log sent at this time every day. 5. Click Save. 11. 10. Monitor the Internet Traffic Statistics The Traffic Statistics page displays the network traffic of the LAN, WAN and WLAN sent and received packets, allowing you to monitor the volume of Internet traffic statistics. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced > System Tools > Traffic Statistics. 67 3. Toggle on Traffic Statistics, and then you can monitor the traffic statistics in Traffic Statistics List section. Click Refresh to update the statistic information on the page. Click Reset All to reset all statistic values in the list to zero. Click Delete All to delete all statistic information in the list. Click Click to reset the statistic information of the specific device. to delete the specific device item in the list. 11. 11. Control LEDs The routers LEDs indicate routers activities and status. You can turn on or turn off the LEDs either from the web management page or by pressing the LED button. To turn on or off the LEDs:

Press the LED button on the router (if available) about 2 seconds to turn on or off the LEDs. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. Click the LED icon in the top right corner of the page. To turn off LEDs during Night Mode Period:

1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2 ) Go to Advanced > System Tools > System Parameters. 3 ) 4 ) Specify a time period in the Night Mode Period as needed, and the LEDs will be In the LED Control section, check the box for Enable Night Mode. off during this period. 5 ) Click Save. 68 69 FAQQ1. What can I do if I forgot my wireless password?

The default wireless password is printed on the label of the router. If the password has been altered, please connect your computer to the router using an Ethernet cable and follow the steps below:

1. Visit http://tplinkwifi.net. 2. Go to Basic > Wireless to retrieve or reset your wireless password. Q2. What can I do if I forgot my login password of the web management The default username and password of the web management page are admin (in lowercase). If your router supports Password Recovery and you have enabled it, please follow the steps below to reset the password without resetting the router:

Note: Make sure the Internet access is available before using this method. 1. Visit http://tplinkwifi.net. 2. Click Forgot password > Send Code, and the verification code will be sent to the page?

mailbox you set. value : admin). 3. Log into your mailbox to copy the verification code. 4. Paste the verification code on the window which pops up in Step 2. 5. Click Confirm (after that, the login username and password will be reset to its default 6. Use admin (in lowercase) as both username and password to login. Tips: Please refer to Password Recovery to learn how to configure Password Recovery. If you have altered the username and password but Password Recovery is disabled:

1. Reset the router to factory default settings: press and hold the Reset button for about 7 seconds and then release;

2. Visit http://tplinkwifi.net, and enter admin (in lowercase) as both username and password to login. Note: Youll need to reconfigure the router to surf the Internet once the router is reset, and please mark down your new password for future use. Q3. What can I do if I cannot log in to the routers web management page?

This can happen for a variety of reasons. Please try the methods below to login again. Make sure your computer is connected to the router correctly and the corresponding LED indicator(s) light up. 70 Make sure the IP address of your computer is configured as Obtain an IP address automatically and Obtain DNS server address automatically. Make sure you enter the correct IP address to login: http://tplinkwifi.net. Check your computers settings:

1 ) Go to Start > Control Panel > Network and Internet, and click View network status and tasks. 2 ) Click Internet Options on the bottom left. 3 ) Click Connections and select Never dial a connection. 4 ) Click LAN settings and deselect the following three options and click OK. 71 5 ) Go to Advanced > Restore advanced settings, click OK to save the settings. Use another web browser or computer to login again. Reset the router to factory default settings and try again. If login still fails, please contact the technical support. Note: Youll need to reconfigure the router to surf the Internet once the router is reset. 72 Q4. What can I do if I cannot access the Internet even though the configuration is finished?

1. Visit http://tplinkwifi.net. 2. Go to Advanced > Status to check Internet status:

As the follow picture shows, if IP Address is a valid one, please try the methods below and try again:

Your computer might not recognize any DNS server addresses. Please manually configure the DNS server. 1 ) Go to Advanced > Network > DHCP Server. 2 ) Enter 8.8.8.8 as Primary DNS, click Save. Tips: 8.8.8.8 is a safe and public DNS server operated by Google. 73 Restart the modem and the router. 1 ) Power off your modem and router, and leave them off for 1 minute. 2 ) Power on your modem first, and wait about 2 minutes until it gets a solid cable or Internet light. 3 ) Power on the router. 4 ) Wait another 1 or 2 minutes and check the Internet access. Reset the router to factory default settings and reconfigure the router. Upgrade the firmware of the router. Check the TCP/IP settings on the particular device if all other devices can get Internet from the router. As the picture below shows, if the IP Address is 0.0.0.0, please try the methods below and try again:

Make sure the physical connection between the router and the modem is proper. Clone the MAC address of your computer. 1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2 ) Go to Advanced > Network > Internet and focus on the MAC Clone section. 3 ) Choose an option as needed (enter the MAC address if Use Custom MAC Address is selected), and click Save. 74 Tips:

Some ISP will register the MAC address of your computer when you access the Internet for the first time through their Cable modem, if you add a router into your network to share your Internet connection, the ISP will not accept it as the MAC address is changed, so we need to clone your computers MAC address to the router. The MAC addresses of a computer in wired connection and wireless connection are different. Modify the LAN IP address of the router. Note:

Most TP-LINK routers use 192.168.0.1/192.168.1.1 as their default LAN IP address, which may conflict with the IP range of your existing ADSL modem/router. If so, the router is not able to communicate with your modem and you cant access the Internet. To resolve this problem, we need to change the LAN IP address of the router to avoid such conflict, for example, 192.168.2.1. 1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for 2 ) Go to Advanced > Network > LAN. 3 ) Modify the LAN IP address as the follow picture shows. Here we take 192.168.2.1 the router. as an example. 4 ) Click Save. Restart the modem and the router. 1 ) Power off your modem and router, and leave them off for 1 minute. 2 ) Power on your modem first, and wait about 2 minutes until it get a solid cable or Internet light. 3 ) Power on the router. 4 ) Wait another 1 or 2 minutes and check the Internet access. Double check the Internet Connection Type. 75 1 ) Confirm your Internet Connection Type, which can be learned from the ISP. 2 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3 ) Go to Advanced > Network > Internet. 4 ) Select your Internet Connection Type and fill in other parameters. 5 ) Click Save. 6 ) Restart the modem and the router again. the wireless network?

Please upgrade the firmware of the router. If youve tried every method above but still cannot access the Internet, please contact the technical support. Q5. What can I do if I cannot find my wireless network or I cannot connect If you fail to find any wireless network, please follow the steps below:

Make sure the wireless function of your device is enabled if youre using a laptop with built-in wireless adapter. You can refer to the relevant document or contact the laptop manufacturer. Make sure the wireless adapter driver is installed successfully and the wireless adapter is enabled. On Windows 7 1 ) If you see the message No connections are available, it is usually because the wireless function is disabled or blocked somehow. 76 2 ) Click Troubleshoot and windows might be able to fix the problem by itself. On Windows XP 1 ) If you see the message Windows cannot configure this wireless connection, this is usually because windows configuration utility is disabled or you are running another wireless configuration tool to connect the wireless. 2 ) Exit the wireless configuration tool (the TP-LINK Utility, for example). 3 ) Select and right click on My Computer on desktop, select Manage to open Computer Management window. 4 ) Expand Services and Applications > Services, find and locate Wireless Zero Configuration in the Services list on the right side. 5 ) Right click Wireless Zero Configuration, and then select Properties. 6 ) Change Startup type to Automatic, click on Start button and make sure the Service status is Started. And then click OK. If you can find other wireless network except your own, please follow the steps below:

Check the WLAN LED indicator on your wireless router/modem. Make sure your computer/device is still in the range of your router/modem. Move it closer if it is currently too far away. Go to Advanced > Wireless > Wireless Settings, and check the wireless settings. Double check your Wireless Network Name and SSID is not hided. If you can find your wireless network but fail to connect, please follow the steps below:

Authenticating problem/password mismatch:

77 1 ) Sometimes you will be asked to type in a PIN number when you connect to the wireless network for the first time. This PIN number is different from the Wireless Password/Network Security Key, usually you can only find it on the label of your router. 2 ) 3 ) If you cannot find the PIN or PIN failed, you may choose Connecting using a security key instead, and then type in the Wireless Password/Network Security Key. If it continues to show note of Network Security Key Mismatch, it is suggested to confirm the wireless password of your wireless router. Note: Wireless Password/Network Security Key is case sensitive. Windows unable to connect to XXXX / Can not join this network / Taking longer than usual to connect to this network:

Check the wireless signal strength of your network. If it is weak (1~3 bars), please move the router closer and try again. Change the wireless Channel of the router to 1,6,or 11 to reduce interference from other networks. Re-install or update the driver for your wireless adapter of the computer. 78 COPYRIGHT & TRADEMARKS is a registered trademark Specifications are subject to change without notice. of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. 79 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

this equipment does cause harmful interference in a residential If Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. RF Exposure Information This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

3 This device may not cause interference, and 4 This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

5 lappareil ne doit pas produire de brouillage;

6 lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B) Korea Warning Statements

. NCC Notice BSMI Notice

.

, Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Dont disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. Adapter shall be installed near the equipment and shall be easily accessible. The plug considered as disconnect device of adapter. Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us. Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.