FCC ID: TE7HS200V5 Kasa Smart Wi-Fi Light Switch, Single Pole

Single Pole Users Manual HS200 Smart Wi-Fi Light Switch, Single Pole 1910012304 REV 2.0.1 Copyright & Trademarks Specifications are subject to change without notice. TP-Link is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. 2017 TP-Link. All rights reserved. www.tp-link.com Contents 4 5 5 7 Introduction Product Requirements Smart Wi-Fi Light Switch Installation Using Kasa with Smart Switches 7 Kasa Account 7 Kasa Settings 8 Customizing Smart Switches 9 Scheduling 9 Creating Scenes 11 Away Mode 12 Runtime Summary 13 Maintaining the Smart Switches 13 Firmware Update 14 Resetting 15 Troubleshooting 15 Frequently Asked Questions 16 Usage Tips 16 Support Users Manual Smart Wi-Fi Light Switch Introduction TP-Link Smart Wi-Fi Light Switch, also referred to as Smart Switch, is a standard, single-pole, wall light switch that can be controlled via your iOS or Android devices. Along with the TP-Link Kasa mobile app, you can follow an intuitive wiring instructions provided to replace your standard in-wall switch, connect the Smart Switch to your home network, then control your lights and create custom lighting automations from anywhere, at anytime with an Internet connection. The Smart Switch is compatible with incandescent, LED, Halogen, and compact fluorescent light bulbs. The switch also includes a white backlight LED indicator to easily locate the switch at night. Blinking Amber and Green: App-Config mode initiated. Green: Lit up for about 30 seconds when successfully connected to the Wi-Fi network, then turns off. Blinking Amber: Resetting. Red: No Wi-Fi connection. White: Lit up when the light is switched OFF to show the Smart Switch location in the dark. RESTART Press to reboot the Smart Switch. RESET Press and hold for about 5 seconds until the Wi-Fi status LED blinks amber and green alternately to initiate App-Config mode. Press and hold for about 10 seconds until the Wi-Fi status LED blinks amber rapidly to factory reset the Smart Switch. www.tp-link.com 4 Users Manual Smart Wi-Fi Light Switch Product Requirements In-wall installation with hardwired connections. Neutral wire required. Single-pole light switch. The electrical box should be more than 2 inches deep. A smartphone or tablet running iOS 9 or higher; Android 4.1x or higher. A Wi-Fi connection (supports 802.11b/g/n standard). Smart Wi-Fi Light Switch Installation Important Safety Information Before installing, servicing, or removing the Smart Switch, read and follow all safety precautions, including the following:

WARNING: RISK OF ELECTRIC SHOCK OR FIRE. Turn OFF power supply at the circuit breaker or fuse. Use a noncontact voltage tester to ensure the power is off. CAUTION: RISK OF ELECTRIC SHOCK. More than one disconnect switch may be required to de-energize the equipment before servicing. Install only in a suitable UL Listed outlet box. The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician. The Smart Switch is an indoor single-pole switch that requires a neutral connection. Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces. Load Information 100~120V ac, 15A max, Res 100~120V ac, 5A, Tungsten 100~120V ac, 5A, Electronic Fluorescent Ballast www.tp-link.com 5 Users Manual Smart Wi-Fi Light Switch 1 Download Kasa for Mobile from the App Store or Google Play. OR scan QR code 2 Connect your mobile device to a 2.4GHz Wi-Fi network. Note: The Smart Switch only supports 2.4GHz networks. 3 Remove the faceplate from the Smart Switch. Launch Kasa and follow the wiring steps provided to instal and connect the Smart Switch to your home network. Sketch 9:41 AM 100%

Sketch 9:41 AM 100%

Sketch 9:41 AM 100%

Add Device Lets get started Kasa will guide you through the wiring process. If you are not comfortable with basic wiring work, please call an electrician. Great!

Smart Bulb Smart Plug Smart Switch Range Extender RE350k S TA RT Your Smart Switch is all set up. It is now saved in your Device List. D O N E ATTENTION: A neutral wire is required to install the Smart Switch. www.tp-link.com 6 Users Manual Smart Wi-Fi Light Switch Using Kasa with Smart Switches Kasa Account While you dont have to have a Kasa account to use TP-Link Smart Home devices, signing up for an account provides added functionality such as:

Synchronization of settings and configurations to all your mobile devices. Ability to control and configure the devices from outside your home. Use of third-party services and products such as Amazon Echo. Devices can only be associated with one Kasa account. To remove the association, turn off Remote Control in the Kasas settings, or factory reset the device. After creating your Kasa account, you will need to verify the email associated with your account by clicking a link in an email that Kasa sends you. Until you verify the email, much of the above functionality will not work. Kasa Settings Kasa Settings allows you to set your global preferences such as:

Remote Control to control your Smart Home devices outside of your home. You need to sign in to your Kasa account first to turn on this function. Location and Time to set the location and time of where the Smart Home devices are located so that the Away Mode and Schedules can run on time. You can set your homes location using your smart devices GPS function, or manually enter the latitude and longitude coordinates. Firmware Update to update your Smart Home devices when there is an update available. Refer to Firmware Update for instructions. www.tp-link.com 7 Users Manual Smart Wi-Fi Light Switch Customizing Smart Switches You can personalize your Smart Switches with a descriptive name, icon, and other information from the switchs details screen. 9:41 PM 100%

Device Settings DEVICE CONTROLS Remote Control Disabled Device Name Front Porch Switch Device Icon DEVICE TIME Time Zone Location DEVICE INFO Model San Francisco Device Time Sept 15, 2015 12:00 PM HS220 1.0.0 1.0.0 MAC Address 00:01:02:03:04:05 Hardware Version Firmware Version Delete Device controls. personalize. icon. 1. On the Devices screen, tap on the row of the Smart Switch to go to its 2. Tap the

(Settings) icon at the top-right corner. 3. On the Device Settings screen, tap the icon for each setting you want to Device Name Create a unique name for your Smart Switch. Device Icon Choose one of the available icons or use your own custom www.tp-link.com 8 Smart Wi-Fi Light Switch You can set up your lights to illuminate around your home at specific times on specific days of the week. 9:41 PM 100%

9:41 PM 100%

Schedules Create Event Users Manual Scheduling No events yet!

Add Events by tapping the button on the top right. Your saved event will be listed here. At 4 5 6 7 8

5 8 5 9 0 0 0 1 0 2 am pm Turn my Smart Plug ON Repeating every S M T W T F S CANCEL SAVE 1. On the Devices screen, tap on the row of the Smart Switch that you want to create a schedule for. 2. Tap

(Schedule) to open the Schedule screen. 4. Within the Create Event screen, set your preferred state for the light bulb (ON 3. Tap to create an event. or OFF), time, and day(s). 5. Tap Save. You can create as many events as you like and edit them at any time from the Schedule screen. Creating Scenes Take full advantage of your TP-Link Smart Home devices in your home with Scenes. A scene is a preset group of Smart Devices (such as Smart Plugs and Smart Switches) that can be customized and controlled simultaneously at the touch of a button from your smartphone or tablet to easily set your mood or fit www.tp-link.com 9 any special occasion. For example, set a customized Movie Time to turn on the home theater system plugged into a Smart Plug and dim down the lights in your Entertainment Room to 10% at the same time. Please keep in mind that SCENES can only be set and controlled once youre signed in to your Kasa account. 1. On the main Home screen, tap the

(Scenes) tab to switch to the Scenes view. 2. Choose one of the preset scenes to start, or choose Custom to set up your own scene that is personalized to suit your liking. To set a scene, you will need to select one or more devices to be controlled, and then define their actions and/or states. 10 Note that you must have at least one Smart Device in order to create a scene. Away Mode Away Mode allows you to automate your Smart Switches in combination with other Smart Home products to respond to your specific schedules. For example, turn on and off Smart Devices at certain intervals to simulate occupancy when youre away from home. 9:41 PM 100%

9:41 PM 100%

Away Mode Select Devices How about picking one light from each room?

BULBS Party Bulb Schedules Devices PLUGS

SAVE 1. Tap the

(navigation drawer) and then Away Mode. 11 2. Tap Select Devices to select your Smart Home devices, and then tap Save. 3. If you want to set a schedule to automate Away Mode so you dont have to manually activate it, tap Set Schedule. Note: Multiple schedules can be set to repeat weekly on the day(s) of your choice. 4. Within the Create Event screen, set your preferred mode (Away or Home), time, and day(s). 5. Tap Save. You can always toggle Away Mode on and off in the sidebar by tapping on the translucent button under the Kasa logo. Runtime Summary The Runtime summary provides a statistical information about how long the Smart Switch has been running. To view the Runtime summary, tap on the Runtime section in the Smart Switchs details screen. 12 Maintaining the Smart Switches Firmware Update To keep the Smart Switches happy and up-to-date with all the latest improvement and fixes, we recommend that you update the firmware when updates are available. 9:41 PM 100%

9:41 PM 100%

Firmware Update New Updates Available We found available firmware updates for your reachable devices. Updating firmware Please do not unplug your devices during the update. Smart Plugs Latest Version: 1.2.0 4 Available Updates Smart Bulb HS100 Latest Version: 1.2.0 2 Available Updates Smart Bulb HS120 Latest Version: 1.2.0 0 Available Updates UPDATE UPDATE 25%

This process may take a few minutes. 1. Launch Kasa. 2. Tap the

(navigation drawer) and then Settings. 3. Tap Firmware Update. 4. Within the Firmware Update screen, tap Update. Remember: Only the Smart Switches that are currently reachable and have an available update will be shown in the Firmware Update screen. It is important to leave the Kasa app running while it finishes updating the Smart Switches. Try not to minimize the app, close the app, or interrupt the update to prevent problems. 13 Resetting Resetting the Smart Switch can help you troubleshoot any issues you may have. Please keep in mind that factory resetting a device will erase all of your custom settings and restore them to factory default settings. RESET The RESET button located underneath the Smart Switch has two functions:

Press and hold for about 5 seconds until the Wi-Fi status LED blinks amber and green alternately to initiate App-Config mode. Press and hold for about 10 seconds until the Wi-Fi status LED blinks amber rapidly to reset the Smart Switch to factory defaults. Note that factory setting the Smart Switch will erase all of your custom settings, and youll have to set it up again. 14 Troubleshooting Frequently Asked Questions 1. What should I do when I cant turn the Smart Switch on/off manually?

If the Smart Switch doesnt respond when pressing the physical switch:

Make sure that you restore power to the Smart Switch at the circuit Make sure the Smart Switch is wired correctly. Please consult with a breaker. qualified electrician. 2. What should I do when the Smart Switch doesnt respond to commands or scheduled automations?

Check your network connectivity. Check if the Wi-Fi status LED on the Smart Switch is blinking amber and green. If so, reconnect the Smart Switch to your Wi-Fi network. Do not use a metal faceplate with the Smart Switch to prevent Wi-Fi signal interference. Power cycle your router and/or reboot the Smart Switch by pressing the RESTART button underneath the switch. Factory reset the Smart Switch by pressing and holding the RESET button. Youll need to configure the Smart Switch again. 3. How far can I be and still able to control my lights via the Smart Switch?

You can be anywhere in the world and still able to control your lights as long as you have an active Internet connection and Remote Control enabled. 4. Can I install two or more Smart Switches to control one light fixture?

No. The Smart Switch is designed for single-pole (one location) wiring only and requires a neutral wire for operation. 5. How do I pair the Smart Switches with Amazon Echo?

For pairing instructions, please visit www.tp-link.com/en/faq-944.html or within the Kasa Help section. 15 Smart Wi-Fi Light Switch Place the Smart Switch within the range of your Wi-Fi router or access point

(approximately 150 feet). Avoid physical obstructions and radio interference in the surrounding area. Users Manual Usage Tips Support Specifications can be found on the product page at www.tp-link.com. Our Technical Support and troubleshooting information can be found at www.tp-link.com/support. FCC compliance information statement FCC compliance information statement Product Name: Kasa Smart Wi-Fi Light Switch, Single Pole Model Number: HS200 Responsible party:

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com www.tp-link.com 16 Users Manual Smart Wi-Fi Light Switch FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning www.tp-link.com 17 Users Manual Smart Wi-Fi Light Switch This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY(the maximum transmitted power) 2412MHz2472MHz(20dBm) No restrictions exist in the use of radio frequencies or frequency bands in all EU member states and EFTA countries. EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce. RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

lappareil ne doit pas produire de brouillage;

1) 2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. www.tp-link.com 18 Users Manual Smart Wi-Fi Light Switch Dclaration dexposition aux radiations Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B) Korea Warning Statements

. NCC Notice BSMI Notice www.tp-link.com 19 Users Manual Smart Wi-Fi Light Switch PCB Pb Cd Hg CrVI PBB PBDE 1. " 0.1wt%" " 0.01wt%"

2. " "

3. ""

. Safety Information Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended Do not use the device where wireless devices are not allowed. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. www.tp-link.com 20 Users Manual Smart Wi-Fi Light Switch Explanation of the symbols on the product label AC voltage Indoor use only RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. www.tp-link.com 21

A B C D E 2 3 4 5 6 7 8 9 1 38.3 1R 5 6 5

. HS200 Kasa Smart Wi-Fi Light Switch, Single Pole Rating: 120 V~ 60 Hz 15 A General Use 600 W Incandescent/LED/CFL TP-Link Technologies Co., Ltd. No.5 Keyuan Road, Nanshan, Shenzhen, 518057, PRC HVIN: HS200V5 FCC ID: TE7HS200V5 IC: 8853A-HS200V5 UL5.0 HS200(US) Ver:5.0 S/N:XXXXXXXXXXXXX 4.8R 38.5 38.5*56.50.2mm, 4.8 R,1R HS200(US)_5.0_ PANTONE 877C PANTONE Cool Gray 2UPANTONE429C 50#PET+

PANTONE 877C A1

-128 HS200(US)_5.0 2020-07-27 1 2 3 4 5 6 7 8 9 A B C D E

TP-Link Technologies Co., Ltd. Authority to Act as Agent Date: August 26, 2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

UL Verification Services (Guangzhou) Co., Ltd., Song Shan Lake Branch is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____2021/1/13_____ ______ Jing Huang __________________

(Print name) _____ Regulatory Compliance Manager __

(Signature1) ________________ By:

Title:

On behalf of: ___ TP-Link Technologies Co., Ltd.__ Telephone:

______ 75521534921 __________

(Company Name) 053019 12

TP-Link Technologies Co., Ltd. Request for Confidentiality Date: August 26, 2020 Subject: Confidentiality Request for: ____ TE7HS200V5_____ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *2 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual TP-Link Technologies Co., Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180)3___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title4) _____________ ________Jing Huang________________

(Print name) 2 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 053019 12