FCC ID: ZMF-TU600B Telematic unit for Fleet Management

TU600B TU600B Technical Manual Version 1.0, March 2022 TU600B Content Content .......................................................................................................... 2 Introduction .................................................................................................... 9 Related Information .......................................................................................................... 9 Safety first...................................................................................................... 9 Simple Guidelines ............................................................................................................ 9 Do Not Operate Where Prohibited ................................................................................... 9 Interference .................................................................................................................... 10 Avoid Body Contact with Device during Operation ......................................................... 10 Qualified Service ............................................................................................................ 10 Accessories and Batteries .............................................................................................. 10 Water-Resistance ........................................................................................................... 10 Detailed Safety Information .......................................................................... 10 Exposure to Radio Frequency Signals ........................................................................... 10 Electronic Devices .......................................................................................................... 11 Pacemakers ................................................................................................................... 11 Other Medical Devices ................................................................................................... 11 Vehicles .......................................................................................................................... 11 Posted Facilities ............................................................................................................. 12 Aircrafts .......................................................................................................................... 12 Potentially Explosive Atmospheres ................................................................................ 12 For Vehicles Equipped with an Airbag............................................................................ 12 Specific Human Absorption Rates (SAR) ....................................................................... 12 Battery Safety Information .............................................................................................. 13 Automatic battery safety during operation .................................................................. 13 Delivered standard content .......................................................................... 14 Ready-to-Use, No Custom Programming Required ....................................................... 14 Cost-effective, Universally Available Communications ................................. 14 Use location Children not likely to be present ............................................................. 15 Practical installation advice ............................................................................................ 15 Installation for insurance and anti-theft purpose ............................................................. 15 Connections ................................................................................................................... 16 Power supply .............................................................................................................. 16 Digital inputs ............................................................................................................... 16 Digital output ............................................................................................................... 16 Motion/acceleration sensor ......................................................................................... 16 Installing the TU600B as to surpass the main switch on the machine. ...................... 17 Functionality check ...................................................................................... 18 Verify my Trackunit ...................................................................................................... 19 Troubleshooting ........................................................................................... 20 Installation of the digital output .................................................................... 21 SMS commands for output control ................................................................................. 22 Safety precautions.......................................................................................................... 22 Warranty ...................................................................................................... 22 Technical Assistance/Support and spare parts ............................................ 22 Minimum Information Required for Technical Assistance ............................................... 24 Trackunit TU600B, Technical Manual v1.0, March 2022 Page 2 TU600B Return Merchandise Authorization RMA ..................................................................... 24 Specifications .............................................................................................. 24 Product specifications .................................................................................................... 24 Connections: ............................................................................................................... 24 Internal temperature ranges: ...................................................................................... 25 External temperature ranges: ..................................................................................... 25 GSM/GPRS-specifications: ......................................................................................... 25 LTE cat M1 / cat NB2 band - specifications: ............................................................... 25 Mechanical specifications ........................................................................................... 27 Approvals and certificates ............................................................................ 28 FCC and IC certification statements ............................................................................... 28 Automotive, off-road vehicles, machinery etc. ............................................................... 29 Statement for ISO 13849-1 safety .............................................................................. 29 EU and UK regulations and directives ............................................................................ 30 CE and UKCA marking ................................................................................................... 31 PTCRB certification for interoperability with mobile networks......................................... 31 Bluetooth SIG registration .............................................................................................. 31 Specific country approval regulations and statements ................................. 31 Australia and New Zealand ............................................................................................ 31 Japan ............................................................................................................................. 32 Chile ............................................................................................................................... 32 Mexico ............................................................................................................................ 32 Brazil .............................................................................................................................. 33 United Arab Emirates (UAE) .......................................................................................... 33 Specific model country approval certificates ................................................ 33 Europe-CEPT ................................................................................................................. 34 UK .................................................................................................................................. 34 Myanmar ........................................................................................................................ 34 Macau ............................................................................................................................ 34 Japan ............................................................................................................................. 34 Australia ......................................................................................................................... 34 New Zealand .................................................................................................................. 34 Singapore ....................................................................................................................... 34 India ............................................................................................................................... 34 Sri Lanka (In process) .................................................................................................... 34 US .................................................................................................................................. 34 Canada ........................................................................................................................... 34 Chile ............................................................................................................................... 34 Trinidad & Tobago .......................................................................................................... 34 El Salvador ..................................................................................................................... 34 British Virgin Islands (BVI) .............................................................................................. 34 Jamaica .......................................................................................................................... 34 Argentina ........................................................................................................................ 34 Uruguay .......................................................................................................................... 34 Bahamas ........................................................................................................................ 34 Guatemala ...................................................................................................................... 34 Peru ................................................................................................................................ 34 Dominican Republic ....................................................................................................... 34 Ecuador .......................................................................................................................... 34 Barbados ........................................................................................................................ 34 Trackunit TU600B, Technical Manual v1.0, March 2022 Page 3 TU600B Belize ............................................................................................................................. 34 Bermuda ......................................................................................................................... 34 Dominica ........................................................................................................................ 35 Paraguay ........................................................................................................................ 35 Columbia ........................................................................................................................ 35 Guyana ........................................................................................................................... 35 Aruba .............................................................................................................................. 35 Panama .......................................................................................................................... 35 Bolivia ............................................................................................................................. 35 Honduras ........................................................................................................................ 35 Nicaragua (In process) ................................................................................................... 35 Mexico (In process) ........................................................................................................ 35 Brazil (In process) .......................................................................................................... 35 Costa Rica ...................................................................................................................... 35 Morocco ......................................................................................................................... 35 Algeria ............................................................................................................................ 35 Madagascar ................................................................................................................... 35 Ghana ............................................................................................................................ 35 Gambia ........................................................................................................................... 35 Zimbabwe ....................................................................................................................... 35 Botswana ....................................................................................................................... 35 Tanzania ........................................................................................................................ 35 Namibia (In process) ...................................................................................................... 35 South Africa .................................................................................................................... 35 Djibouti ........................................................................................................................... 35 Qatar .............................................................................................................................. 35 Kuwait ............................................................................................................................ 36 Oman ............................................................................................................................. 36 Israel .............................................................................................................................. 36 Turkey ............................................................................................................................ 36 Saudi Arabia ................................................................................................................... 36 Jordan ............................................................................................................................ 36 Lebanon (In process) ..................................................................................................... 36 Bahrain ........................................................................................................................... 36 Pakistan ......................................................................................................................... 36 Turkmenistan ................................................................................................................. 36 Uzbekistan ..................................................................................................................... 36 United Arab Emirates (UAE) .......................................................................................... 36 Yemen (In process) ........................................................................................................ 36 Environmental compliance ........................................................................... 36 Trackunit TU600B, Technical Manual v1.0, March 2022 Page 4 TU600B Corporate Office Trackunit APS Gasvaerksvej 24, 4 sal 9000 Aalborg Denmark. www.trackunit.com Copyright and Trademarks 1998-2020, Trackunit APS. All rights reserved. Trackunit, Trackunit logo and Trackunit are trademarks of Trackunit APS, registered in the United States and in other countries. All other trademarks are the property of their respective owners. Release Notice This document is release v1.0 of the TU600B, Technical Manual. THIS MANUAL IS INTENDED FOR USE BY SYSTEM INTEGRATORS, SERVICE PROVIDERS AND APPLICATION DEVELOPERS (COLLECTIVELY, RESELLERS). IT IS NOT INTENDED FOR END-USERS OF THE TU600B. ANY END-

USER DOCUMENTATION IS TO BE PREPARED AND FURNISHED BY THE RESELLERS. The following Product Limited Warranty gives Resellers specific legal rights. You may have others, which vary from state/jurisdiction to state/jurisdiction. Product Limited Warranty Subject to the terms and conditions set forth herein, Trackunit APS (Trackunit) makes the following warranty only to its Resellers who purchase the TU600B hardware product

(Product) directly from Trackunit: for a period of one (1) year from the date of shipment from Trackunit, the Product will substantially conform to Trackunits standard published specifications for the Product and the Product hardware will be substantially free from defects in materials and workmanship. The foregoing warranty shall not apply to embedded software/firmware components. THIS PRODUCT LIMITED WARRANTY IS PROVIDED TO RESELLERS AND TO RESELLERS ONLY. RESELLER IS SOLELY RESPONSIBLE FOR ANY AND ALL WARRANTIES MADE TO ITS CUSTOMERS, AND TRACKUNIT MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SHALL HAVE NO OBLIGATIONS OR LIABILITY TO RESELLERS CUSTOMERS OR END-USERS OF THE PRODUCT. RESELLER SHALL NOT MAKE ANY REPRESENTATIONS OR WARRANTIES ON TRACKUNITS BEHALF, AND SHALL FULLY INDEMNIFY, DEFEND AND HOLD TRACKUNIT HARMLESS FROM ANY BREACH OF THE FOREGOING. IF RESELLER DISTRIBUTES PRODUCT TO END-USER CUSTOMERS, RESELLER SHALL BE SOLELY RESPONSIBLE FOR PREPARING AND PROVIDING PRODUCT WARRANTIES AND PRODUCT LITERATURE TO END-USERS. Warranty Remedies If the Product fails during the warranty period for reasons covered by this Product Limited Warranty and Reseller notifies Trackunit of such failure during the warranty period, Trackunit at is option will repair OR replace the nonconforming Product, OR refund the purchase price paid by Reseller for the Product, provided that Reseller returns the Product to Trackunit in accordance with Trackunits standard return material authorization procedures or as otherwise instructed by Trackunit. Warranty Exclusions and Disclaimers The foregoing Product Limited Warranty shall only apply in the event and to the extent that (i) the Product is properly and correctly installed, configured, interfaced, maintained, stored and operated in accordance with Trackunits specifications, and

(ii) the Product is not modified or misused. This Product Limited Warranty shall not apply to, and Trackunit shall not be responsible for, defects or performance problems resulting from:

(a) the combination or utilization of the Product with hardware or software products, information, data, systems, interfaces, services or devices not made, supplied or specified by Trackunit; (b) the operation of the Product under any specifications other than, or in addition to, Trackunits standard published specifications for the Product; (c) the unauthorized installation, modification or use of the Product; (d) damage caused by: accident, lightning or other electrical discharge, water immersion or spray, or exposure to environmental conditions for which the Product is not intended; or (e) normal wear and tear on consumable parts, including by way of example and without limitation, batteries. TRACKUNIT DOES NOT WARRANT OR GUARANTEE THE RESULTS OBTAINED THROUGH THE USE OF THE PRODUCT. THE FOREGOING TERMS OF THE PRODUCT LIMITED WARRANTY STATE TRACKUNITS ENTIRE LIABILITY, AND RESELLERS EXCLUSIVE REMEDIES, RELATING TO THE USE AND PERFORMANCE OF THE PRODUCT EXCEPT AS OTHERWISE EXPRESSLY PROVIDED FOR IN THIS PRODUCT LIMITED WARRANTY, THE PRODUCT, ACCOMPANYING DOCUMENTATION AND MATERIALS, AND/OR ANY EMBEDDED SOFTWARE/FIRMWARE AND UPDATES THERETO ARE PROVIDED AS-IS AND WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND, BY EITHER TRACKUNIT OR ANYONE WHO HAS BEEN INVOLVED IN ITS CREATION, PRODUCTION, INSTALLATION OR DISTRIBUTION, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NONINFRINGEMENT. THE STATED EXPRESS WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART OF TRACKUNIT ARISING OUT OF, OR IN CONNECTION WITH, THE PRODUCT. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING:

TRACKUNIT IS NOT RESPONSIBLE FOR THE OPERATION OR FAILURE OF OPERATION OF GPS SATELLITES OR WIRELESS SERVICE OR THE AVAILABILITY OF GPS SATELLITE SIGNALS OR WIRELESS SERVICE. THE PRODUCT MAY CONTAIN TECHNOLOGY THAT IS NOT FAULT TOLERANT AND IS NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE IN ENVIRONMENTS OR APPLICATIONS IN WHICH THE FAILURE OF THE PRODUCT WOULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE OR SEVERE FINANCIAL LOSS. ANY USE OR DISTRIBUTION BY RESELLER OR ITS CUSTOMERS IN CONNECTION WITH ANY SUCH ENVIRONMENT OR APPLICATION SHALL BE AT TU600B RESELLERS AND ITS CUSTOMERS SOLE RISK, AND TRACKUNIT SHALL HAVE NO LIABILITY WHATSOEVER IN CONNECTION THEREWITH. RESELLER SHALL INDEMNIFY AND HOLD TRACKUNIT AND ITS SUPPLIERS HARMLESS FROM ANY CLAIM BROUGHT AGAINST TRACKUNIT WHICH ARISES FROM RESELLERS USE OR DISTRIBUTION OF THE PRODUCT IN CONNECTION WITH SUCH ENVIVRONMENTS OR APPLICATIONS. SOME STATES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED WARRANTY, SO CERTAIN OF THE ABOVE LIMITATIONS MAY NOT APPLY TO EVERY RESELLER. Embedded Software/Firmware The Product and associated tools, if any, may contain embedded software/firmware, which is licensed, not sold, and is only for use within the Product as an integral part thereof. Such embedded software/firmware (which includes all updates thereto) contains valuable trade secrets and is proprietary to Trackunit and its suppliers. To the greatest extent permitted by law, such embedded software/firmware may not be modified, copied, disassembled, decompiled or reverse engineered. Trackunit reserves all other rights. Limitation of Liability TRACKUNITS ENTIRE LIABILITY REGARDING THE PRODUCT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY RESELLER FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL TRACKUNIT OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER UNDER ANY CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANY WAY TO THE PRODUCTS, ACCOMPANYING DOCUMENTATION AND MATERIALS, AND ANY EMBEDDED SOFTWARE/FIRMWARE AND UPDATES THERETO (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR ANY OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER TRACKUNIT HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING BETWEEN TRACKUNIT AND RESELLER. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO EVERY RESELLER. Notices Class B Statement Notice to Users. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Regulatory Approvals CE The TU600B product comply with the essential requirements of the RED Directive 2014/53/EU as stated by the Declaration of Conformity (CE). The TU600B product comply with the European Telecommunications Standards Institute Specifications EN 301 489-1, EN 301489-17 (Bluetooth LE), EN 301 489-19 (GPSS/GNSS) and EN 301 489-52 (EMC for GPS, GSM 900MHz/1800MHz and LTE cat M1/NB2 700MHz/900MHz/1800MHz/2100MHz Radio Equipment and Systems). EU/ International/Automotive The TU600B product comply with the essential requirements of the UN regulative ECE R10 EMC rev5 clause 6.5, 6.6, 6.8 and 6.9, The TU600B product comply with the essential requirements of the Directive 2006/42/EC, EU regulation 167/2013 and the Directive 2014/30/EU; with standards ISO-13766-1, -2 and EN ISO 14982, ISO 12895 for tractors, forest, and agricultural machinery, moving machinery, construction machinery, lifts, trucks etc. The product complies with the essential requirements of the 2011/65/EC directive and amendment 2015/863/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (ROHS 3). The product complies with the essential requirements of the EC 1907/2006 regulation concerning the Registration, Evaluation, Authorization and Restriction of Chemicals

(REACH). The product complies with the requirements of the 2012/19/EU directive on waste electrical and electronic equipment (WEEE). FCC The TU600B product comply with the FCC Part 15, Part 22, Part 24, Part 27, part 90 and the Industry Canada requirements RSS-102, RSS-132, RSS-133, RSS-139. The TU600B product comply with Part 15 of the FCC rules and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. For fixed mounted operations the TU600B must be installed to provide a separation distance of at least 20 cm from all persons. MIC (Japan)

(Shared with Quectel BG95-M3 module certificate):

The TU600B product complies with the Japanese Telecommunication Business Act for radio terminal equipment supporting LTE M1 / NB IoT at 800, 1800, 2100 MHz (Band B18/B19, B3, B1) and Bluetooth LE (2402 2480 MHz). Trackunit TU600B, Technical Manual v1.0, March 2022 Page 6 TU600B Bluetooth SIG registered:

Declaration ID: D050742 Company identifier UUID: 2159 (0x086F) Automotive:

KBA UN ECE R10 rev 5/1 certified :

Insurance and Pension (Tracking system):

Denmark-FOP Control certificate:

Europe:

EU certificate:

CE mark by EU-Tec certificate:

United Kingdom (UK):

UKCA mark by DOC Oceania:

Australia SDOC approval:

RCM mark by SDOC from E7689 New Zealand approval:

NZS mark by importer SDOC from local office. Asia:

Japan certificates:

India:

ETA-WPC Certificate number:

Myanmar:

N/A - Accept EU-TEC certificate upon request. Macau:

CTT no certification required. Singapore:

IMDA Certificate number: xxxx-xx / DB107653 USA / CANADA US and Canada certificates:

FCC ID: ZMF-TU600B IC:

9746A-TU600B US - CTIA certificates:

PTCRB ID:

LATAM America El Salvador:

CNAF Certificate number:

Trinidad and Tobago:

TATT approval number: ZMF-TU600B

(Recognized by FCC approval ID) British Virgin Islands (BVI):

TRC Certificate number:

Jamaica:

SMA approval number: ZMF-TU600B

(Recognize by FF approval ID) Uruguay:

URSEC Certificate number:

Bahamas:

URCA Certificate number:

Guatemala:

SIT Approval number:

Peru:

Homologation Certificate number:

Dominican Republic:

INDOTEL Certificate number:

Ecuador:

Certificate number:

Barbados:

MED Approval number:

Belize:

PUC Certificate number:

Bermuda:

BRA Bluetooth certificate number:

BRA Cellular certificate number:

(Accept FCC ID: ZMF-TU600B and CE mark) Columbia:

CRC Certificate number:

(Approval of BG95-M3 in product with TAC: 86773005) CRC Certificate number:

(Approval of BG95-M3 in product with TAC: 35361794) Dominica:

NTRC Certificate number:

Paraguay:

CONATEL Certificate number:

Argentina:

ENACOM Certificate number:

Guyana:

TA Reference number:

Trackunit TU600B, Technical Manual v1.0, March 2022 Page 7 TU600B South Africa:

ICASA certificate number:

Djibouti:

DDTIC certificate number:

Middle East:

Turkey:

(Listed but import license acquired.) Israel:

MOC certificate/import license :

(Individual import application required) Jordan:

TRC require import statement for showing compliance to TRC regulations by importing company. Trackunit letter available. Qatar:

CRA approval certificate:

Kuwait:

CITRA certificate number:

Oman:

OMAN TRA certificate number:

Saudi Arabia:

CITC certificate number:

Bahrain:

TRA certificate number:

United Arab Emirates (UAE):

TDRA certificate number:

with dealer number Pakistan:

TAC certificate number:

Turkmenistan:

TDS certificate number:

Uzbekistan:

OSTZ certificate number:

TA approval number: ZMF-TU600B

(Recognize by FCC approval ID) Aruba:

DTZ Reference number:

(Recognize FCC approval ID) Panama:

ASEP Certificate number:

Bolivia:

ATT Certificate number:

(Recognize FCC approval ID) Honduras:

CONATEL homologation number:

Chile:

Exempted for IMEI listing due to roaming SIM card and fixed installation. Mexico:

(Product safety, Import) ANCE NOM-019 Certificate number:

NOM-208 Certificate number:

NOM-221 Certificate number:

NOM-221 Certificate number:

IFETEL certificate number for permanent Radio approval:

Nmero IFETEL:

Brazil:

ibrace COC technical certificate number:

ANATEL certificate number:

Costa Rica:

SUTEL approval number:

North Africa / Sub Sahara Morocco:

ANRT technical certificate:

Algeria:

ARPCE certificate number:

Madagascar:

ARTEC approval certificate Ghana:

NCA approval certificate:

Gambia:

PURA approval certificate:

Botswana:

BOCRA certificate number:

Zimbabwe:

POTRAZ certificate number:

Tanzania:

TCRA certificate number:

Trackunit TU600B, Technical Manual v1.0, March 2022 Page 8 TU600B Introduction This document contains the installation guide for the (GSM / LTE cat-M1 / NB2-IOT / GNSS / BLE) product type series TU600B units. This manual is intended for use by system integrators, service providers and application developers (collectively, Resellers). It is not intended for end-users of the TU600B. Any end-user documentation is to be prepared and furnished by the resellers. This manual covers the TU600B with 60.012 and later firmware operating on:

2G bands [850 MHz, 900 MHz, 1800 MHz and 1900 MHz] Global System for Mobile LTE bands [700 MHz, 800 MHz, 850 MHz, 900 MHz, 1700 MHz, 1800 MHz, 1900 MHz, Data and Event Reporting support is by Short Message Service (SMS), General Packet communication (GSM) networks. 2100 MHz] LTE M1/NB2 IOT networks. Radio Service (GPRS), or both. This manual describes how to set up, configure, install, operate, and troubleshoot the product. Even if you have used other GSM, LTE cat-M1 / NB2- IOT or Global Positioning System (GPS) products before, Trackunit recommends that you spend some time reading this manual to learn about the special features of this product. Trackunit assumes that you are familiar with Microsoft Windows. Related Information The Trackunit web site is found at www.trackunit.com. This site links to the fleet management system from Trackunit APS called Trackunit Manager. TU600B devices are integrated to Trackunit but can also be used together with third part system providers. Safety first Simple Guidelines Please follow these guidelines when configuring, using or recycling the TU600B. Violating these guidelines may be dangerous, illegal or otherwise detrimental. Further detailed information is provided in this manual. Do Not Operate Where Prohibited Do not allow the TU600B unit to operate wherever wireless phone use is prohibited or when doing so may cause interference or danger. The TU600B cannot be turned off after installation, so any vehicle, moving machinery, construction machinery using TU600B etc. must not enter areas where it is prohibited to operate wireless phones as the device periodically turns on the transmitter in a short period of time to perform tracking reporting. Examples include but are not limited to operation in hospitals, aircrafts, near blasting sites or wherever operation can cause interference. TU600B Interference Like all wireless devices, the TU600B may encounter electrical interference that may affect its performance. Avoid Body Contact with Device during Operation Do not operate the TU600B in direct contact with your body. Maintain at least 8 inches (20 cm) separation between the device and any parts of your body. Qualified Service Except for batteries and Subscriber Identification Module (SIM) card, the TU600B contains no user serviceable or replaceable parts. Non-functioning units must be returned to an authorized service center for repair or replacement. Accessories and Batteries Use only Trackunit approved accessories or batteries. Do not connect incompatible products. The battery package is a Trackunit design, no other battery designs are compatible with the battery holder of the TU600B. There is risk of explosion or fire if an incorrect type replacement battery is forced into the battery holder as contact may generate a short circuit. Additionally, the battery holder will be destroyed. Do not exceed the temperature ranges or other environmental conditions specified by the battery manufacturer, see battery safety chapter below. Dispose of used batteries according to the instructions provided with the batteries. Water-Resistance The TU600B series is water-resistant according to the IP-67 standard. It is however recommended that it is be used where it is relatively dry and not subjected to either water streams or submersion. Mounted inside the HW shield a higher water-resistance level to IP-66k and IP 69k can be achieved. Detailed Safety Information Exposure to Radio Frequency Signals The TU600B unit is a low power radio transmitter and receiver. Periodically the TU600B wakes up either due to activity or by a timer. When it is ON, it receives and sends out radio frequency (RF) signals for a short period of time when awake. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 10 TU600B The TU600B unit cannot be turned off after installation; however, the unit is mostly asleep waiting for either the wake-up timer or activity on the acceleration sensor. The unit operation can continue for approximately 3 to 4 days depending on the charging state of the backup battery. The TU600B unit is designed for vehicular use only. Electronic Devices Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals generated by the TU600B unit. Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six (6) inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. The following precautions apply:

The TU600B unit is not intended for handheld use or to be worn on the body. It is always recommended that a minimum separation of 8 inches (20 cm) to be maintained between the TU600B unit and any persons body after end user installation. Other Medical Devices If any other personal medical devices are used in the vicinity of a TU600B unit, consult the manufacturers of the medical devices to determine if they are adequately shielded from external RF energy. Physicians may be able to assist in obtaining this information. The TU600B unit cannot be turned off after installation, so any vehicle, moving machinery, construction machinery installed with the TU600B etc. must not operate near health care facilities when any regulations posted in these areas prohibit the use of wireless phones or two-way radios. Hospitals and health care facilities may be using equipment that could be sensitive to external RF energy. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding the vehicle. Also consult the manufacturer of any equipment that has been added to the vehicle. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 11 TU600B Posted Facilities The TU600B unit cannot be turned off after installation, so any vehicle, moving machinery, construction machinery installed with the TU600B etc. must not enter any facility where posted notices prohibit the use of wireless phones or two-way radios. Aircrafts FCC and FAA regulations prohibit using wireless phones while in the air. Do not carry the TU600B unit aboard an aircraft as it cannot be turned off. Potentially Explosive Atmospheres The TU600B unit cannot be turned off after installation, so any vehicle, moving machinery, construction machinery installed with TU600B etc. must not enter any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Additionally, the TU600B must not enter or in areas posted turn off two-way radio to avoid interfering with blasting operations. Obey all signs and instructions. Areas with a potentially explosive atmosphere are often, but not always marked clearly. Potential areas may include: fueling areas (such as gasoline stations); below deck on boats; fuel or chemical transfer or storage facilities; vehicles using liquefied petroleum gas (such as propane or butane);

areas where the air contains chemicals or particles (such as grain, dust, or metal powders); and any other area where it would normally be advisable to turn off motor vehicle engines it is not allowed to enter with a vehicle, moving machinery, construction machinery installed with the TU600B. For Vehicles Equipped with an Airbag An airbag inflates with great force. DO NOT place objects, including the TU600B unit, in the area over the airbag or in the airbag deployment area. If in vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. Specific Human Absorption Rates (SAR) THE TU600B UNIT IS NOT DESIGNED TO BE WORN ON A PERSONS BODY. AS SUCH, BODY WORN TEST POSITIONS FOR THE TU600B UNIT ARE NOT REQUIRED BY EITHER THE IEC 62311 FOR GSM 900/1800 MHz BANDS, LTE M1/NB IOT 800/900/1800/2100 MHz BANDS OR FCC/IEEE/ICNIRP REQUIREMENTS FOR GSM 850/1900 MHz BANDS, LTE M1/NB IOT 700/850/1700/1900 MHz bands. The TU600B unit is not intended for handheld use or to be worn on the body. A minimum separation of ten (8) inches (20 cm) is to be maintained between the TU600B and any persons body. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site at www.ctia.org. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 12 TU600B Battery Safety Information Adhere to the following guidelines to avoid the risk of fire or explosion:

1. Dispose of the used battery according to the instructions provided with the battery. 2. Do not drop, puncture, disassemble, mutilate, or incinerate the battery. 3. Touching both terminals of a battery with a metal object will short circuit the battery. Do not carry batteries loosely if the contacts may touch coins, keys, and other metal objects (such as in pockets or bags). 4. Do not stack batteries taken out of the carry case. 5. Do not heat the batteries to try to rejuvenate their charge. 6. Do not exceed the temperature ranges or other environmental conditions specified by the battery manufacturer when handling replacement batteries. 7. Never install and use the TU600B without the battery cover installed. 8. The TU600B can operate solely on the vehicles battery without the internal backup battery installed. It is recommended to remove the battery under long term exposure to extreme environmental conditions above +60C and below -20C. Automatic battery safety during operation For operational safety the battery inside the TU600B is under constant environmental temperature control providing the following automatic battery safety. The battery can only be charged within the specified temperature range 0C to +45C. For temperatures outside the range 0C to 45C, the battery charging circuit is disabled. The TU600B operates solely from the internal backup battery supply voltage when the external supply voltages is turned off or experiencing failure. The internal backup battery is limited to operate in the temperature range from -20C to 60C. If the temperature is outside this range the battery is disabled. When TU600B is operated from an external supply voltage the battery is put into storage from temperatures above +45C and below -20C. If the battery is fully charged and the temperature is within 0C to 45C a maintenance charging is applied. For long term storage in extreme temperatures below -20C and above +50C it is recommended to remove the battery from TU600B. The battery safety ensures that there is no risk* associated with the battery in the temperature range from -40C to +70C but the battery lifetime can be seriously affected or even lead to internal permanent damage of the battery.

* The risks are: No leakage, No venting, No disassembly, No rupture or No fire. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 13 TU600B Delivered standard content The delivered standard package content includes the following items:

1 x (GSM / LTE cat-M1 / cat BN2 / GPS/GLONASS)-unit of the model type TU600B 1 x Li-ion Battery PN 4233.0002 or PN4233.0002 (May already be mounted inside the TU600B 1 x Mounting cradle. unit) Optional content for generic installation:

1 x Fuse with fuse holder for installation up to 24V DC/ (Max 1A) for TU600B units delivered with open cable ends. For installation in systems with higher voltages than 24V it is recommended to use a fuse and fuse holder rated for the specific supply voltage range, see service chapter for compliant fuse holders. NOTE: Fuse and fuse holder is not included in packages where the TU600B is fitted with a customer required connector from factory. In case the unit is delivered with SIM card from the factory (Either US, EU SIM card or E-SIM as indicated on the product label), then the GSM/LTE cat-M1/cat-NB2 number will be indicated on the delivery note as well as on the package itself. NOTE: In case the SIM card is delivered from factory it is mounted inside the TU600B unit. NOTE:

Ready-to-Use, No Custom Programming Required Simply connect the unit to supply voltage (12V/24V/48V DC). In its default configuration, reports are sent nominally at 15-minute intervals or faster whenever there is motion. Upon powering up, the device will self-initialize anywhere in the world and start transmitting if an authorized GSM network is available. While a basic understanding of the different TU600B operational states is helpful, configuring the TU600B unit does not require a highly skilled software programmer or technician. Cost-effective, Universally Available Communications The TU600B unit takes advantage of the near universal availability of GSM/LTE M1/NB IOT SMS text messaging while also leveraging cost-effective GPRS data rate plans. Typical SMS plans offer very extensive inter-network roaming capabilities, both within a host country and internationally. SMS plans also tend to be too pricey for applications requiring more than a few reports per day. GPRS data plans, on the other hand, typically allow for lower recurring communication costs although GPRS coverage and roaming can be restricted in some areas. The TU600B unit takes advantage of both technologies by automatically selecting GPRS wherever such service is available, while relying upon SMS text messages for configuration purpose only. This helps minimize recurring communication costs while allowing the greatest coverage possible. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 14 TU600B Installing the unit Use location Children not likely to be present This equipment design typically applies to commercial or industrial equipment expected to be installed in locations where only adults are normally present. Practical installation advice It is very important to be careful when installing the unit, as incorrect installation will reduce the quality of the GPS position reports (Ex. Could be a jump in position or showing speed while parking) or in the worst-case scenario will prevent the unit performing any position reporting at all. The unit must NOT be installed beneath metal plates or inside closed metal compartments. Incorrect installation will also reduce the standby time of the battery inside the unit The unit must be mounted either horizontally or vertically (sideways) using either screws or strips. The unit must not be installed with the interface/supply cable hanging down, as this will reduce the GPS sensitivity. Optimize the placement of the unit to increase the aerial view (through windows etc.) as much as possible. For hiding the unit, make sure it is only mounted beneath plastic parts or similar parts (wood), but not beneath metal parts. To reduce hum and noise in the FM radio it is recommended to place the unit at a minimum distance of 20 inches (50 cm) from the radio or the loudspeakers. Installation for insurance and anti-theft purpose For an installation of the TU600B with respect to insurance coverage of equipment/items/vehicles etc. in your country/region please contact your nearest sales office for support as the TU600B installation must be registered and documented for the local insurance company, the associated local alarm center. The installation position in multiple equipment/items/vehicles etc. of the same type must be insured to be random to increase the theft protection. It is needed to sign up a different subscription for each installed TU600B unit under insurance coverage that covers the local alarm center administration of the units. The local sales office will be able to inform you about the obligations that you have in relation to the insurance company and how to act in relation to the alarm center while the units are covered by the insurance. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 15 TU600B Connections The connections depend on the type of vehicles / machines etc. in which the (GSM/LTE M1/NB IOT)/GPS unit is to be installed. Different variants of the TU600B device will have only a subset of the connections shown in the table below. Please contact your nearest sales office, distributor or Reseller for further information about the availability of other variants in your area. Wire

(color code) Red White Brown Grey Yellow Green TU600B function Supply voltage +12V / +24V Digital input 1 Digital input 2 (Ignition) Digital input 3 Digital output 1 1-Wire input (M8 Connector) Pink Digital input 4 Orange CAN HI (Optional) Light Blue CAN LO (Optional) Blue Common ground Power supply The unit must be connected to either +12V, +24V battery voltage through a 1A/32V fuse or +36V,

+48V battery through 3A/80V fuse. The use of a fused supply wire is important for not damaging the wires related to the unit in case of a short circuit etc. Digital inputs The activation of a digital input requires a minimum high-level voltage of 9,5V. Digital output The digital output has the type indication LO-side switch, that connects the output to 0V ground, when the output is active. This output can be used to control a relay powered from an external DC supply voltage. The maximum current drawn from the output is 200mA. The output is protected against short circuits, overload and is also protected against over voltage. For further information about connection possibilities of the digital output, see chapters about installation later in this manual. Motion/acceleration sensor The unit has a built-in 3 axis acceleration sensor that can activate the unit if it, as a consequence of disconnected supply voltage, is in stand-by mode (theft protection), log accelerometer data (for analyzing shock and machine behavior) or configured as a tilt-sensor. CAN interface TU600 is equipped with a built-in CAN Controller. Protocols supported: SAE J1939 and CANopen. The CAN interface is Fully Compliant with CAN 2 Part A and 2 Part B. Eight independent message objects (mailboxes) are implemented, and Trackunit TU600B, Technical Manual v1.0, March 2022 Page 16 TU600B Controller supports Bit Rates up to 1 Mbit/s. Physical Interface specification as referred to by ISO/11898-2. 120R CAN termination optional:

Mounted, Not Mounted or controlled by Firmware (CAN configuration). The CAN Interface is only operational when supply voltage (12V / 24V / 48V) is present. Interface cannot operate on internal battery alone. M8 Connector: 1-Wire input The M8 3 pole connector contains 3 signals: 1-wire bus, 5V and Ground. The 1-wire is designed to communicate with Maxim 1-wire parts. Ex. Digital Thermometer

(Temperature logging) or Maxim ibutton Keys/tags (Access Control). The 1-wire input is only operational when supply voltage (12V / 24V / 48V) is present. Interface cannot operate on internal battery alone. Installing the TU600B as to surpass the main switch on the machine. In case the main switch on the machine will break the negative wire (Ground wire), the inputs may register a voltage level and start counting operating hours. To avoid this situation the digital input 4

(Pink wire) should be connected to the chassis/ground on the machine. Then send the following SMS to the unit (phone number) to activate the filtering:

Function Activate filter function on inputs. Send SMS MT INFILT ON Return-SMS from the unit MTC ACK (SERIAL No.) INFILT ON NOTE: Enabling the filtering function will disable the use of the digital input 4 as a normal input. NOTE:

It is recommended always to connect digital input 2 to the ignition signal of the vehicle or machine. NOTE: For the Send SMS it is of no importance if small or capital letters are used in the command string, or a mixture hereof. Wireless connectivity: Bluetooth LE The TU600B can operate in Bluetooth LE band for access control, device configuration and asset tracking. The TU600B will operate on a BT LE radio wave system when assessed by a paired unit i.e. cellphone. When connected the cellphone can be used as a mean for access control to the vehicles, machinery etc. on which the TU600B is physically installed. In addition to the use case described above the TU600B can also be requested to passive scan for BLE advertisements and thereby enable assert tracking. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 17 TU600B Functionality check Trackunit TU600B, Technical Manual v1.0, March 2022 Page 18 TU600B Verify my Trackunit In order to control if the installation of the TU600B unit has been done correctly, it is possible to use the Verify my Trackunit tool. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 19 TU600B Troubleshooting Various error situations are listed below along with some possible solutions. Error code F1 Error description The unit does not answer the SMS command send to it. Possible solutions Verify if the SMS messages are sent to the correct GSM/LTE M1/NB IOT phone number. Check LED status; See the Functionality check chapter in this F2 F3 The LED in the unit is off, thus no power on the unit. The LED is constant red;

thus the unit is not attached to the GSM /

LTE network manual. If the TU600B unit has been delivered with the SIM card mounted. Contact Trackunit support. o Or contact the mobile operator to verify if there is any problem with the SIM card. Verify if the SIM card is correctly mounted in the unit. Check if the installation is performed correctly according to the guidelines of this manual. If the TU600B unit has been delivered with the SIM card mounted. Contact Trackunit support. o Or contact the mobile operator to verify if there is any problem with the SIM card. Verify if the SIM card is correctly mounted in the unit. Verify if the PIN code has been disabled from the SIM card before it was inserted in the unit F4 The unit send reply messages but there is no GPS signal Verify if the unit is mounted according to the instructions laid out in this manual with respect to the aerial view; see Installing the unit chapter. If the machine/vehicles are located inside a building, please move the machine/vehicle outside a try again. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 20 TU600B Installation of the digital output According to the E1 certificate of the TU600B unit, it is prohibited under any circumstances to use this output to control any equipment that may influence the safety of the construction machinery and earth moving machines/vehicle operation and driving. The output must only be used to control comfort equipment. The example shows a 12V relay function with a 12V DC supply voltage. It is also possible to use a 24V relay with a 24V DC supply voltage etc. The current consumption of the relay must not exceed 200 mA (DC current) and the relay contacts must be specified to withstand the load that needs to be controlled. NOTE: The output can only handle DC and not AC voltage. It is necessary to only use a DC power supply for the relay. Important!

The power supply connected to the TU600B (GSM/LTE M1/NB IoT)/GPS unit and the supply voltage for the relay mounted on the digital output must have a common ground connection. One application example for the Usable contact function controlled by the TU600B signals shown in the figure above could be a Start Relay, blocking function, for preventing unauthorized use of the moving machinery and construction machine or vehicle outside normal working hours etc. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 21 TU600B SMS commands for output control Function Activation of the output Send SMS MT OUT1=ON Return SMS MTC ACK (SERIAL No.) OUT1 ON Deactivation of the output MT OUT1=OFF MTC ACK (SERIAL No.) OUT1 OFF Description With this command the output is activated permanently. The output can be de-

activated again using the OFF command. With this command the output is deactivated. NOTE: For the Send SMS it is of no importance if small or capital letters are used in the command string, or a mixture hereof. Safety precautions The use of the digital output is restricted to signals/systems/components related to comfort applications in the vehicles. Under no circumstances must it be used for purposes, which can influence the safety of the vehicle when driving. Trackunit holds no liability for any damages occurred to persons, vehicles, moving machines, construction machines etc. caused by wrong installation and/or faulty use of the digital output. Warranty Trackunit APS products are covered by a limited manufacturer warranty. The Trackunit APS warranty is limited to the warranty rules and legislation present in each country. The warranty only covers manufacturing faults. The warranty does not cover misuse, wrong installation or damage due to a faulty installation or wrong maintenance. The invoice act as the proof of warranty, so please keep it as reference for any warranty complaints. Technical Assistance/Support and spare parts Trackunit APS offers technical assistance to all our customers about the use, installation, insurance, and spare parts:

If you have a problem and cannot find the information you need in the product documentation, please contact Trackunit Aps. For replacement batteries Trackunit model PN 4233.0002 or PN 4233.004 must be used, please order at Trackunit Aps. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 22 TU600B For mounting the Trackunit TU600B in harsh environment, not covered by the compliance statements or areas where pressure cleaning is required the Trackunit HW shield PN 7402.9551 is required for protective mounting. Please order at Trackunit Aps. Recommended fuse holders and fuses up to 48V supply voltages (Can be ordered at Trackunit APS):

a. Supply voltage 12V/24V (Max 30A) i. ATO blade fuses (Max 32V/1A) used with Littelfuse FHAC0002SXJ fuse holder (Standard). ii. ATP blade fuse (Max 32V/1A ATO style) used with TaiTek FH-006WR-

12R-12-U fuse holder (Standard). b. Supply voltage 12V 48V (Max 30A) i. FKS blade fuse (Max 80V/3A ATO style) used with Littelfuse FH2 fuse holder. (Recommended) Left: 32V/1A fuse kit, Right: 80V/3A fuse kit Trackunit Aps Gasvaerksvej 24, 4 sal Dk-9000 Aalborg Tel: +45 9973 0020 Fax: +45 9673 7407 E-Mail: support@trackunit.com Web: www.trackunit.com Trackunit TU600B, Technical Manual v1.0, March 2022 Page 23 TU600B When contacting technical support, please be prepared to provide the information listed below:

Minimum Information Required for Technical Assistance If you or a user reports difficulty with a TU600B unit (i.e. no GPS fixes, not communicating, LED not working, etc.), it is helpful to retrieve directly from the unit all current configuration settings and the message log data etc., that is accessible by the technical support when they receive the following information about the unit. 2. Unit Serial number Return Merchandise Authorization RMA 1. If you experience defects in your product, please contact our customer support at:

support@trackunit.com or phone +45 96 73 74 00 Your inquiry will be processed by our support team and a support ticket number will be created in our system. You will receive your ticket number by email. 2. In case your hardware needs to be sent to us you will receive an RMA form by email from our support team that you must fill out. Print out the RMA and pack it together with the faulty product and send both to the following address:

Trackunit Aps Gasvaerksvej 24, 4 sal DK-9000 Aalborg Denmark Attention: Service Specifications The product specifications are described below. Product specifications The TU600B unit is a (GSM/GPRS quad-band-unit and a combined LTE M1 / NB IoT multiband unit) with GPS, integrated antennas, acceleration sensor, 2Mbyte SPI flash and a backup battery Connections:

Operational voltage (supply voltage):

Absolute maximum voltage range:

Standby consumption (GSM/LTE M1/NB IOT-

receiver active) 12 48 V DC 8 58 V DC continuous 10 mA / 7 mA (average at 12V / 24V) Consumption during charging on an empty battery 225 mA / 115 mA (max at 12V / 24V) Standby time on the backup-battery 2-4 days Trackunit TU600B, Technical Manual v1.0, March 2022 Page 24 Charging time for an empty backup-battery Expected lifetime of the backup-battery 3 hours at 25 C 3 years TU600B Digital inputs Digital outputs 1-Wire interface CAN interface Bluetooth 5 LE (wireless) Internal temperature ranges:

Charging or maintenance charging (With external DC supply voltage)

(If the temperature exceeds this range the charging is disabled, and the battery put into internal storage mode) In active running mode (Without external DC supply voltage)

(If the temperature exceeds this range the battery supply voltage is disabled, and the battery put into internal storage mode. Due to a small internal self-heating during operation this may occur at external temperatures between 55C 60C.) Internal storage without loss of battery performance

(Specified by battery cell vendor. This range apply for the TU600B operated from an external DC supply voltage outside the charging temperature range.) Internal storage with loss of battery performance

(Within battery safety limits)

(According to the MSDS, UN38.3 and IEC62133:2012 testing, it is safe to keep the battery in storage for shorter periods above +50C or below -20C. For longer exposures to extreme temperatures it is recommended to remove the battery from the TU600B). External temperature ranges:

Recommended operational temperature range (External/Internal DC supply)

(See internal temperature ranges for details) Internal Storage

(Warning: Battery life time and performance not guaranteed for temperatures from -40C to -20C or from +50C to +70C)

(See internal temperature ranges for details). 4 1 Optional Optional Optional 0C to +45C

-20C to +60C

-20C to +50C

-40C to +70C

-20C to +55C/+60C

-40C to +70C GSM/GPRS-specifications:

Supporting EGSM/GPRS/EGPRS 900/1800/850/1900 with maximum output power:

at EGSM-GPRS/EGPRS 900 MHz:

at GSM-GPRS/EGPRS 850 MHz:

at GSM-GPRS/EGPRS 1800/1900 MHz:

Additionally, supports GPRS/EGPRS Multislot class 33, CS 14 and MCS 1-9 2.0W 2.0W 1.0W LTE cat M1 / cat NB2 band - specifications:

Supporting LTE cat M1 / cat NB2 band 600/700/800/900/1800/2100/850/1700/1900 with maximum output power:

Trackunit TU600B, Technical Manual v1.0, March 2022 Page 25 TU600B Pmax = 0.3W TU600B supports band :

LTE-FDD cat M1; B1 / B2 / B3 / B4 / B5 / B8 / B12 / B13 / B18 / B19 / B20 / B25 /

B26 / B27 / B28 / B66 / B85:

LTE-FDD cat NB2; B1 / B2 / B3 / B4 / B5 / B8 / B12 / B13 / B18 / B19 / B20 / B25

/ B28 / B66 / B71 / B85:

B1: TX 1920-1980 MHz, RX 2110-2170 MHz B2 / (GSM1900): TX 1850-1910 MHz, RX 1930-1990 MHz B3 / (GSM1800): TX 1710-1785 MHz, RX 1805-1880 MHz B4: TX 1710-1755 MHz, RX 2110-2155 MHz B5 / (GSM850): TX 824-849 MHz, RX 869-894 MHz B8 / (GSM900): TX 880-915 MHz, RX 924-960 MHz B12: TX 699-716 MHz, RX 728-746 MHz B13: TX 777-787 MHz, RX 746-757 MHz B18: TX 815-829.9 MHz, RX 860-874.9 MHz B19: TX 830-844.9 MHz, RX 875-889.9 MHz B20: TX 832-862 MHz, RX 791-821 MHz. B25: TX 1850-1915, RX 1930-1995 MHz (Extended PCS band) B26: TX 814-848.9 MHz, RX 859-893.9 MHz (Extended 850 MHz band) B27: TX 807-824 MHz, RX 852-869 MHz (Sub 850 MHz band) B28: TX 703-748 MHz, RX 758-803 MHz B66: TX 1710-1780 MHz, RX 2110-2200 MHz B85: TX 698-716 MHz, RX 728-746 MHz B1: TX 1920-1980 MHz, RX 2110-2170 MHz B2 / (GSM1900): TX 1850-1910 MHz, RX 1930-1990 MHz B3 / (GSM1800): TX 1710-1785 MHz, RX 1805-1880 MHz B4: TX 1710-1755 MHz, RX 2110-2155 MHz B5 / (GSM850): TX 824-849 MHz, RX 869-894 MHz B8 / (GSM900): TX 880-915 MHz, RX 924-960 MHz B12: TX 699-716 MHz, RX 728-746 MHz B13: TX 777-787 MHz, RX 746-757 MHz B18: TX 815-829.9 MHz, RX 860-874.9 MHz B19: TX 830-844.9 MHz, RX 875-889.9 MHz B20: TX 832-862 MHz, RX 791-821 MHz. B25: TX 1850-1915, RX 1930-1995 MHz B28: TX 703-748 MHz, RX 758-803 MHz B66: TX 1710-1780 MHz, RX 2110-2200 MHz B71: TX 663-698 MHz, RX 617-652 MHz B85: TX 698-716 MHz, RX 728-746 MHz The marked bands B12/B13 are denoted LTE 700 MHz band lower and upper part. The bands B18/B19 are denoted LTE 800 band lower and upper part for Japan. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 26 TU600B Mechanical specifications Dimensions: Length:

Width:

Height:

Cable length:

Environmental class:

Enclosure material:

Weight:

122.1 mm 45.65 mm (49 mm incl. mounting cradle) 18 mm (23 mm incl. mounting cradle) 170 180 cm IP67 (Standalone) IP66K, IP69K (Mounted with HW shield) Non-flammable PP casing and ABS cable connector lid. 65 g (excluding the cable) Trackunit TU600B, Technical Manual v1.0, March 2022 Page 27 TU600B Approvals and certificates The TU600B product is certified according to KBA (E1 mark), EU (CE mark), UK (UKCA mark) USA (FCC ID), Canada( IC ID), Japan JATE/MIC ID (GITEKI mark), Australia ACMA (RCM mark), New Zealand (R mark), Argentina (RAMATEL mark), Mexico safety (NOM mark), SUTEL (Costa Rica), NCA (Ghana), ICASA (South Africa), Chile (Resolution 403:2008), Ingress Properties (IP mark), Bluetooth SIG (BLE mark), CTIA (IoT Network mark), UAE (TRA), OMAN (TRA), Singapore

(IMDA):

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Trackunit APS is under license. Other trademarks and trade names are those of their respective owners. FCC and IC certification statements The TU600B product contains radio transmitters that comply with CFR 47 Part 15, Part 15.247, Part 22, Part 24, Part 27 and Part 90 of the FCC rules and with RSS-GEN, RSS-102, RSS-130, RSS-132, RSS-133, RSS-139 and RSS-247 of Industry Canada requirements. Statements according to CFR 47 Part 15.19 / RSS-GEN:

The TU600B product complies with Part 15 of the FCC rules and with ICES-003 of Industry Canada rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Dclarations selon le CFR 47 section 15.19 / RSS-GEN:

Le prsent TU600B appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Statements according to CFR 47 Part 15.21:

Changes or modifications made to this equipment not expressly approved by Trackunit may void the FCC authorization to operate this equipment. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 28 TU600B Statements according to CFR 47 Part 2.1091 and RSS-102:

With respect to radiofrequency radiation exposure Information, it is declared that this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclarations selon le CFR 47 Sections 2.1091 et RSS-102:

Respectant les informations relatives lexposition aux radiations de frquences radio, on dclare que cet quipement respecte les limites dexposition aux radiations de la FCC aux conditions prvues pour un environnement non contrl. Cet quipement doit tre install et fonctionner une distance minimale de 20 cm entre Cet metteur ne doit pas tre install ou utilis en conjonction avec dautres antennes lappareil irradiant et votre corps. ou dautres metteurs. Statements according to CFR 47 Part 15.105 and ICES-003:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and ICES-003 of the Canadian rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Automotive, off-road vehicles, machinery etc. UN regulative ECE R10 EMC rev. 05/01 in accordance with EU regulation 661/2009. o Tested by ECE R10 rev05/01. The TU600B product complies with the essential requirements of the Directive 2006/42/EC and EU regulation 167/2013 construction machinery:

o Tested in compliance to EN ISO 14982, ISO 13766-1, -2, EN 13309, DIN EN 12895, see below. Statement for ISO 13849-1 safety 1. The TU600B products are when installed not a vital part in the machine safety system, but it can be used as access control/immobilizer if paired with a keypad (i.e. DualID II), ibutton or wireless (Bluetooth LE enabling). This function depends on correct installation (see Trackunit TU600B, Technical Manual v1.0, March 2022 Page 29 TU600B install guide) and requires that the output wire is connected to a relay to control the starter motor. 2. When the emergency stop on the machine is activated, the unit and keypad functions will be disabled. The internal battery ensures that a GPS position still can be acquired on an hourly basis. Precaution: Trackunit recommends only mounting Output1 to starter motors through a relay and under no circumstances should Output1 be used to control engine shutdown during operation or any moving parts on the machine. EU and UK regulations and directives The TU600B product complies with the essential requirements of the Automotive Directive The TU600B product complies with the essential requirements of the RED Directive 2014/53/EU directive with respect to the EMC requirements, safety, vehicles transients and radio spectrum and the council recommendation 1999/519/EC on the limitation of exposure of the general public to electromagnetic fields (0 Hz to 300 GHz), when used as intended. o The TU600B product also complies with the essential requirements of the Directive 2014/30/EU for the use of harmonized standards for machinery and vehicles EMC:

EN ISO 14982, EN 13309, EN 12895 and ISO 13766-1, -2 The TU600B product complies with the essential and environmental requirements of the Interoperability of trans-European conventional rail system 2001/16/EC and 2004/50/EC directives, when used as intended on rolling stock. The TU600B complies with the essential requirements of the 2011/65/EC directive with the amendment 2015/863/EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (ROHS 3). The TU600B complies with the essential requirements of the 1999/45/EC directive as amended by EC 1907/2006 regulation concerning the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH). The TU600B complies with the requirements of the 2012/19/EU directive on waste electrical and electronic equipment (WEEE). Including:

Standard UK Restriction of use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation 2012 UK SI 2012 No. 3032. Version Description ISO 13766-1, ISO 13766-2 2018 Earth-moving machinery and Construction machinery EN 13309 2010 Construction machinery Trackunit TU600B, Technical Manual v1.0, March 2022 Page 30 TU600B EN/ISO 14982 EN 12895, DIN EN 12895 2010 2015

(Expire 2021-06-30) Agricultural and forestry machines Industrial trucks Electromagnetic compatibility

(EN/IEC 62368-1 + AC/3 +

A11) 2014, 2015, 2017 Information and communication technology equipment safety EN/IEC 62133 {Ed2}

2012 Safety requirements for portable sealed secondary cells and for batteries made from them. CE and UKCA marking We, Trackunit Aps hereby declare that the TU600B product complies with the essential requirements of the RED Directive 2014/53/EU as stated by the EU Declaration of Conformity and the Radio Equipment Regulations 2017 UK SI 2017 No. 1206. EU Certificate and Declaration of conformity (DOC) statements can be downloaded from the Trackunit website:

https://www.trackunit.com/support/download/

PTCRB certification for interoperability with mobile networks. All variants of the TU600B products series under FCC ID: ZMF-TU600B and IC: 9746A-TU600B are certified for PTCRB interoperability with mobile networks. Specific Trackunit model design certificates have been obtained for:

Approval ID: for TU600-25 Bluetooth SIG registration The TU600-25 product is Bluetooth SIG registered under declaration ID: D050742 supporting core specification 5.1. Trackunit Aps is listed with company identifier UUID: 2159 (0x086F) Specific country approval regulations and statements Australia and New Zealand The TU600B product complies with the requirements of the relevant ACMA Standards made under the Radiocommunications Act 1992 and the Telecommunications Act 1997, by the Suppliers Declaration of Conformity (SDOC). These Standards are referenced in notices made under section 182 of the Radiocommunications Act and 407 of the Telecommunications Act. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 31 The TU600B product complies with the requirements of the relevant standards under Section 134 (1) (g) of the New Zealand Radiocommunications Act 1989, by the Suppliers Declaration of Conformity (SDOC) The TU600-25 model of the product family TU600B is approved in Japan with the certificate ID n: [T] D200116003, [R] 003-200139, [R] 020-190254

(That contains a Bluetooth Low Energy interface) This device is granted pursuant to the Japanese Radio Law ()

This device should not be modified (otherwise the granted designation number will become invalid) Translated (For information only):

This device is granted pursuant to the Japanese Radio Law (Radio Act)

= The equipment is equipped with specified wireless equipment that has received a certificate of conformity with technical standards based on the Radio Law. This device should not be modified (otherwise the granted designation number will become invalid) Modification of this product is prohibited (Compliance certification number etc. become invalid.) Chile For Chile, a label must be applied in the user manual for compliance with the radio and EMC TU600B Japan law:

Mexico For Mexico, the label for NOM-019, NOM-008, NOM-221 compliance certification must be applied in the user manual for compliance with the safety rules SCFI-1993:

Trackunit TU600B, Technical Manual v1.0, March 2022 Page 32 TU600B La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Brazil For the ANATEL homologation of the TU600-25 in Brazil the below information applies:

Modelo: TU600-25 Para maiores informaes, consulte o site da ANATEL www.anatel.gov.br Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados United Arab Emirates (UAE) Besides the approval label in the user guide a Declaration of Conformity label is required for the retail boxes when importing TU600-25 to UAE. The label is mandatory for sales and distribution in UAE in either color or BW:

Specific model country approval certificates The specific country approvals are listed in the table below. For some countries an importing license apply as no certification or approval is applicable for the TU600-25. Trackunit TU600B, Technical Manual v1.0, March 2022 Page 33 Certificate number Label TU600B Country UK Russia, Myanmar Macau Japan Europe-CEPT TU600-25 EU-NB Model Regulatory body TU600-25 TU600-25 TU600B BSI EAC PTD TU600B TELEC/

JATE/

MIC TU600-25 CTT

(NOTE: No certification required) UKCA mark EAC mark

(NOTE: Accept EU DoC for Import if requested)

[T] D200116003

[R] 003-200139

[R] 020-190254 RCM mark

(By local signed SDOC) Australia TU600-25 ACMA New Zealand TU600-25 NZ Local importer must apply for approval Singapore TU600-25 IMDA DB 107653 India TU600-25 ETA-WPC Sri Lanka TU600-25

FCC ISED TU600B TU600B TU600B TU600-25 TATT TBD

(Local importer required) FCC ID: ZMF-TU600B IC: 4796A-TU600B

(NOTE: Label required for compliance to radio law) Reference:

Accept FCC-ID: ZMF-TU600B El Salvador TU600-25 CNAF British Virgin Islands (BVI) TU600-25 TRC Reference:

Accept FCC ID: ZMF-TU600B TU600-25 SMA Accept FCC-ID: ZMF-TU600B US Canada Chile Trinidad &

Tobago Jamaica Argentina Uruguay Bahamas Guatemala Peru Dominican Republic Ecuador Barbados Belize TU600-25 ENACOM TU600-25 URSEC TU600-25 URCA TU600-25 TU600-25 SIT TRF TU600-25 INDOTEL TU600-25 ARCOTEL TU600-25 TU600-25 MED PUC Yes Yes Yes No No Yes Yes Yes Yes No Yes Yes Yes Yes No No No No Yes No No No No No No No No No Bermuda TU600-25 BRA

(Bluetooth)

(Cellular) Trackunit TU600B, Technical Manual v1.0, March 2022 Page 34 TU600B Country Dominica Paraguay Columbia Guyana Model Regulatory body TU600-25 NTRC TU600-25 CONATEL BG95-M3 TU600-25 TU600-25 CRC CRC TA Aruba TU600-25 DTZ Panama Bolivia Honduras Nicaragua Mexico TU600-25 ASEP TU600-25 ATT TU600-25 CONATEL TU600-25 TELCOR TU600-25 ANCE:

NOM-019 ANCE:

NOM-208 ANCE:

NOM-221 IFETEL ANATEL Brazil TU600-25 ibrace Costa Rica TU600-25 SUTEL Morocco TU600-25 ANRT Algeria TU600-25 ARPCE Madagascar TU600-25 ARTEC Ghana Gambia Zimbabwe Botswana Tanzania Namibia Djibouti Qatar TU600-25 NCA TU600-25 PURA TU600-25 POTRAZ TU600-25 BOCRA TU600-25 TU600-25 TU600-25 TCRA CRAN ICASA DDTIC TU600-25 CRA South Africa TU600-25 Certificate number Label

(Approved for BG95-M3 TAC: 86773005)

(Approval of TU600-25 TAC: 35361794) Reference:

Accept FCC-ID: ZMF-TU600B Reference:

Accept FCC-ID: ZMF-TU600B 4860 Reference:

Accept FCC-ID: ZMF-TU600B Part 1:

Part 2:

Technical certificate for import:

(NOTE : Import license required) No Yes No No No No No No No No Yes Yes Yes Yes No No No Yes No No No No No Yes No No Trackunit TU600B, Technical Manual v1.0, March 2022 Page 35

(Import license number:

for 2022/2023) Turkey TU600-25 TTTE

(Sinif 2)

(NOTE: Import manufacturer declaration required) Saudi Arabia TU600-25 Jordan TU600-25 CITC TRC

(NOTE: Import application stating compliance to TRC regulations) TU600B Country Model Regulatory body Kuwait TU600-25 CITRA Oman TU600-25 Israel TU600-25 TRA Dealer MOC Turkmenistan TU600-25 TU600-25 MOC TU600-25 TU600-25 TU600-25 TU600-25 TRA TAC TDS OSTZ TDRA Lebanon Bahrain Pakistan Uzbekistan United Arab Emirates

(UAE) Yemen TU600-25 MTIT Certificate number Label No Yes No No No No No No No No No Yes No Environmental compliance The TU600B are designed for compliance to the following environmental standards related to the intended use of the product:

Standard Version Description A, B SAE J1455:2017, EN/IEC 60068-2-1 SAE J1455:2017, EN/IEC 60068-2-2 SAE J1455:2017, EN/IEC 60068-2-27, IEC 61373 SAE J1455:2017, EN/IEC 60068-2-31 SAE J1455:2017, EN/IEC 60068-2-64 SAE J1455:2017, EN/IEC 60068-2-64, IEC 61373 IEC 60721-2-3 Cold Dry Heat Shock Drop, free fall Random vibration Acceleration Attitude 2007 2006 2010 2008 2008 2010 2013 2001 2018, 2013 SAE J1455:2017, EN/IEC 60068-2-78 Damp heat steady state EN/IEC 60068-2-5, ASTM D4329 UV protection Trackunit TU600B, Technical Manual v1.0, March 2022 Page 36 TU600B NOTE A:

NOTE B:

SAE J1455:2017, IEC 60529 + A1 + A2 (CSV) {Ed3.1}

2013 IP67 - Degrees of protection without HW shield IP69K & IP66K mounted inside HW shield. The TU600B is not to be mounted in areas with presence of Motor oil, Gasoline, Diesel fuel, Hydraulic fluid, Brake fluid, Transmission fluid , Glycol and water mixture etc. The housing not designed to withstand high pressure cleaning. Only use the TU600B when mounted inside the designated Trackunit protection cap (Can be ordered at Trackunit APS) in mounting areas where high pressure cleaning is common procedure. Environmental protection without HW shield:

Trackunit TU600B, Technical Manual v1.0, March 2022 Page 37 TU600B Environmental protection with use of HW shield:

Trackunit Aps Gasvaerksvej 24, 4 sal DK-9000 Aalborg Denmark Phone +45 9673 7400 Trackunit TU600B, Technical Manual v1.0, March 2022 Page 38

. n o i t c e t o r p f o r e y a l a r t x e n a g n d d a i

, s t n e m n o r i v n e h s r a h n i w a R t c e t o r p o t e d a M l t n u o M d e h S w a R i s e i r o s s e c c a e h t d n i F r. o f g n i k o o l e r u o y 2 t o p S t i n u k c a r T i e d u G n o i t a l l a t s n I r u o y n i s n o i t i d n o c e r u t a r e p m e t i e n h c a m c fi c e p s o t i w a R t i n u k c a r T i

. t n e m p u q e r u o y o t s s e c c a l o r t n o c o t

. s r o t a r e p o r o f s s e c c a d r a c D F R D I I l a u D r o s n e S e r u t a r e p m e T l y a e R f o o r P h s a p S l e r u s a e m o t w a R o t t c e n n o C e c a f r e t n i o t

, d e r i u q e r n e h w d e s U y a w y s a e n a s i d r a c D F R D I I l a u D e h T s d r a C D I l a u D e t a v i t c a o t l o o t y s a e a s i r e d a e r d r a c D F R B S U I r e d a e R d r a C D I F R

. t n e m n o r i v n e

. s l o r t n o c r o s l a n g i s g n i r i w e c a f r e t n i o t

, d e r i u q e r n e h w d e s U l s y a e R d r a d n a t S

, s t n e m n o r i v n e h s r a h n i I I i e n h c a m c fi c e p s o t i w a R t i n u k c a r T

. n o i t c e t o r p f o r e y a l

. s l o r t n o c r o s l a n g i s g n i r i w

. s l e d o m x

0 0 6 U T r e d r O s s e c c u S r e m o t s u C r e t n e C p e H l d n a r e v e n e h W

. e r e h s i l p e H

. t i d e e n u o y r e v e w o h u o y t a h w w o n k y d a e r l A r u o o t t u o h c a e r e s a e P l d n a

, n o i t a v i t c a

, n o i t a l l a t s n I t a r e d r o r u o y e c a P

d e e n l t a m a e t t r o p p u s d e c n e i r e p x e d n u o f e b n a c o f n i i g n d r a o b n o m o c

. t i n u k c a r t m o c

. t i n u k c a r t

t r o p p u s m o c

. t i n u k c a r t r. e t n e c p e h t a l 0

. 1 V 3 0 5 2 8 0 0 7

. t e k c a r B I I D I l a u D D I l a u D t c e t o r p o t e d a M a r t x e n a g n d d a i t i n u k c a r T t c e n n o c o t s n o i t u o s e l l i t a s r e V l e b a C r e w o P r o f d e fi i t r e c d n a d e n g i s e D e t i r r e F

. i e n h c a m f o e p y t y n a o t w a R d n a 1 0 5 U T h t i

w n a p a J n i e s u Trackunit Spot Empowering Non-Powered Equipment Installation How to Install the Spot Trackunit Spot How to Use the Spot 1. Mounting Orientation To get the most optimal performance out of the Spot:

Vertical Mounting Horizontal Mounting Mount the Spot upright with the Antenna facing the sky. The LED on the front will be on the bottom of the device. Mount the Spot horizontally with the Antenna facing the sky. The LED on the front will be on the bottom of the device. 2. Mounting the Spot Install the Spot by inserting the two M4 (5/32) screws through the Mounting Holes and into the Mounting Surface. Use a TX20 (0.6 Nm) screwdriver to tighten the M4 screws;

be careful not to overtighten. Meet Trackunit SPOT, a battery-powered telematics device that tracks your equipment. Mounting Location Screw Mounting Avoid mounting the Spot under metal objects or next to electrical wiring. Mounting Hole: 4 mm (0.15) Screw Type: M4 (5/32) Screws 3. Activating the Spot Remove the activation sticker from the front of the Spot and expose it to direct light to trigger device activation. Activate the Spot after installation or after the onboarding process. Note: You need to activate the Spot before it transmits data. i i i Track your equipment 1, 2, 3, or 4 times per day or even every second, the choice is yours Turn on movement detection so you never have to worry about theft or unauthorized use. Turn on the tracking feature, allowing you to follow and locate your equipment. Help is here, whenever you need it. Remove the activation sticker covering the light sensor. The LED indicator on the front of the Spot will flash green, indicating the device is active. Use Trackunit Manager to configure how often Spot transmits an updated location (default is one time per day) Note: During the activation process, it can take up to 3 seconds for the LED Indicator on the Spot to start flashing. Help Center Customer Success Order Installation, activation, and onboarding info can be found at helpcenter.trackunit.com Please reach out to our experienced support team at support@trackunit.com Already know what you need? Place your order at trackunit.com One Platform Add attachments and unpowered equipment to the same platform. One View Track your equipment and attachments alongside the rest of your fleet. One Minute On-site installation takes only one minute. Product Information Overview W = 53.3 mm / 2.10 inches Trackunit Spot is a battery-powered telematics solution that provides performance, durability, and flexibility to manage your fleet of non-pow-

ered assets, machines, or equipment. L

1 2 1

. 6 m m

4

. 7 9 i n c h e s

1

. 2 7 i n c h e s H

3 2

. 2 m m Compatible With Dimensions Length: 121.6 mm (4.79) Width: 53.3 mm (2.10) Height: 32.2 mm (1.27) Weight: 150g (5.3 oz) Tech Specs Network: LTE-M1 / NB-IoT Approvals: CE, FCC/IC, and PTCRB GNSS: GPS, GLONASS, BeiDou, Gallieo, and QZSS Battery: 3.6V / 2 x 3.6Ah Capacity: 4000 pings Temperature: - 30C to + 60C (- 22F to + 140F) Environmental Class: IP66K, IP69K, and UL94-V0 3 Axis Accelerometer Included Spot 2x M4 (5/32) Screws User Guide Raw Kin

Trackunit Spot2 Safety, Technical, and Compliance Statements Safety Statements Compliance Statements Environmental Hazard Warning: Lithium-Ion batteries damaged during transportation are subject to local laws and reg-

ulations regarding disposal. Check with your local landfill/recycling facility for hazardous waste disposal requirements and safe disposal options. Non-Ionizing Radiation Hazard Warning: Do not remove the activation sticker (tab) unit you have completed the Devices installa-

tion process. Removing the activation sticker will cause the Device to emit non-ionizing radiation. Warning: Make sure to mount the Device in a location more than 20 cm (7.5) away from human interaction. General Hazards Caution: Trackunit strongly recommends that you have the proper certifications and training in in-

stalling GPS, Cellular, and electrical equipment, according to your local guidelines. If you do not possess the required knowledge, contact a certified Technician. Caution: Please review and adhere to your companys ergonomic policies and procedures while installing the Device. Warning: Make sure you wear all required safety equipment during installation. Warning: Do not cut, crimp, or pinch internal wiring when replacing the devices Lithium-Ion bat-

tery. Risk of Ingress of Water Caution: Mount the Spot2 on a level surface using the mounting hardware (included) to maintain the IP rating. Caution: Do not clean the Spot2 with water while the equipment is hot. Wait until the Device has cooled down and is at the same temperature as the water used to clean the Device. Technical Specifications Statements Description Network GPS Battery Battery Capacity Operating Temperature Environmental Class Accelerometer Mounting Hole Size Weight Technical Specifications LTE-M1 / NB-IoT GPS, GLONASS, BeiDou, Gallieo, and QZSS 3.6V / 2 x 3.6Ah 4000 Pings

-30oC to 60oC (-22oF to 140oF) IP66 and IP68 3-Axis 4.2 mm (0.16) 150g (5.3oz) FCC part 15.19 Notice This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-

tions: (1) this Device may not cause harmful interference, and (2) this Device must accept any interfer-

ence received, including interference that may cause undesired operation. FCC parte 15.19 Aviso Este dispositivo cumple con la Parte 15 de las Reglas de la FCC El funcionamiento est sujeto a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencias perjudiciales, y (2) este dis-

positivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar un funcionamiento no deseado. FCC part 15.21 Notice Changes or modifications made to this equipment not expressly approved by Trackunit may void the FCC authorization to operate this equipment. FCC ID: ZMF-TU600B ISED Notice This Device complies with Industry, Science, and Economical Development Canadas RSS applicable to licence-exempt radio apparatus. Operation is permitted under the following two conditions: (1) the apparatus must not cause interference, and (2) the user of the apparatus must accept any radio inter-

ference suffered, even if the interference is likely to compromise its operation. Le prsent appareil est conforme aux CNR dIndustrie Science et dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux condi- tions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisa- teur de lappareil doit ac-

cepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This Class B Digital Device complies with CAN ICES-003 (B) Cet Appareil numerique de la classe (B) est conforme a la norme NMB-003 du Canada. IC: 9746A-TU600B CE and UKCA Hereby, Trackunit Aps declares that the radio equipment type Spot2 is in compliance with EU directive 2014/53/EU and UK Radio Equipment Regulations 2017. The full text of the EU and UKCA declaration of conformity is available at the following internet address:

https://trackunit.com/guides-manuals/#Declarations-of-Comformity. EU/International/Automotive The Spot2 complies with the essential requirements of the UN regulative ECE R10 EMC rev5 clause 6.5, 6.6, 6.8 and 6.9. Spot2 Safety and Regualations v2.indd 1 Revision Date: 07/14/2022 2022-07-14 11:09:25 AM Safety, Technical, and Compliance Statements Trackunit Spot2 Safety Statements Compliance Statements Environmental Hazard Warning: Lithium-Ion batteries damaged during transportation are subject to local laws and reg-

ulations regarding disposal. Check with your local landfill/recycling facility for hazardous waste disposal requirements and safe disposal options. Non-Ionizing Radiation Hazard Warning: Do not remove the activation sticker (tab) unit you have completed the Devices installa-

tion process. Removing the activation sticker will cause the Device to emit non-ionizing radiation. Warning: Make sure to mount the Device in a location more than 20 cm (7.5) away from human interaction. General Hazards Caution: Trackunit strongly recommends that you have the proper certifications and training in in-

stalling GPS, Cellular, and electrical equipment, according to your local guidelines. If you do not possess the required knowledge, contact a certified Technician. Caution: Please review and adhere to your companys ergonomic policies and procedures while installing the Device. Warning: Make sure you wear all required safety equipment during installation. Warning: Do not cut, crimp, or pinch internal wiring when replacing the devices Lithium-Ion bat-

tery. Risk of Ingress of Water the IP rating. Caution: Mount the Spot2 on a level surface using the mounting hardware (included) to maintain FCC part 15.19 Notice This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-

tions: (1) this Device may not cause harmful interference, and (2) this Device must accept any interfer-

ence received, including interference that may cause undesired operation. FCC parte 15.19 Aviso Este dispositivo cumple con la Parte 15 de las Reglas de la FCC El funcionamiento est sujeto a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencias perjudiciales, y (2) este dis-

positivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar un funcionamiento no deseado. FCC part 15.21 Notice Changes or modifications made to this equipment not expressly approved by Trackunit may void the FCC authorization to operate this equipment. FCC ID: ZMF-TU600B ISED Notice This Device complies with Industry, Science, and Economical Development Canadas RSS applicable to licence-exempt radio apparatus. Operation is permitted under the following two conditions: (1) the apparatus must not cause interference, and (2) the user of the apparatus must accept any radio inter-

ference suffered, even if the interference is likely to compromise its operation. Le prsent appareil est conforme aux CNR dIndustrie Science et dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux condi- tions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisa- teur de lappareil doit ac-

cepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution: Do not clean the Spot2 with water while the equipment is hot. Wait until the Device has cooled down and is at the same temperature as the water used to clean the Device. This Class B Digital Device complies with CAN ICES-003 (B) Technical Specifications Statements Description Technical Specifications GPS, GLONASS, BeiDou, Gallieo, and QZSS Network GPS Battery Battery Capacity Environmental Class Accelerometer Mounting Hole Size Weight LTE-M1 / NB-IoT 3.6V / 2 x 3.6Ah 4000 Pings IP66 and IP68 3-Axis 4.2 mm (0.16) 150g (5.3oz) Operating Temperature

-30oC to 60oC (-22oF to 140oF) Cet Appareil numerique de la classe (B) est conforme a la norme NMB-003 du Canada. IC: 9746A-TU600B CE and UKCA Hereby, Trackunit Aps declares that the radio equipment type Spot2 is in compliance with EU directive 2014/53/EU and UK Radio Equipment Regulations 2017. The full text of the EU and UKCA declaration of conformity is available at the following internet address:

https://trackunit.com/guides-manuals/#Declarations-of-Comformity. EU/International/Automotive The Spot2 complies with the essential requirements of the UN regulative ECE R10 EMC rev5 clause 6.5, 6.6, 6.8 and 6.9. Spot2 Safety and Regualations v2.indd 1 Revision Date: 07/14/2022 2022-07-14 11:09:25 AM

TU600B labels for external marking, standard:

Variant 1: TU600-25 Variant 1: TU600-21 Variant 1: TU600-22 TU600B device label for Model: TU600-25:

Label print out and placement. Trackunit Aps Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00 www.trackunit.com

Declaration of Equality Class 2 Permissive Change (C2PC) 2022-09-26 Industry Canada; Certification and Engineering Bureau Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to the applicable paragraphs in ISEDs RSP-100 7 and CFR 47 FCC part 2.1043(b)(2) we hereby declare the following changes under Class II Permissive Change to the product:

Telematic unit for Fleet Management installed in machinery, vehicles etc. model ID:

TU600-21 with:

FCC ID: ZMF-TU600B IC ID: 9746A-TU600B We, Trackunit Aps hereby declare the following Class 2 Permissive Change to the Telematic unit TU600-21 related to the FCC/RSS regulations in the original certificate to create the standalone Telematic unit TU600-21:

The HVIN is unchanged i.e. Model ID: TU600-21 The product marketing name (PMN) will change from Trackunit to Trackunit SPOT2. The external and internal mechanical construction has changed significantly to change the product from an automotive electronic sub assembly (ESA) with an automotive interface and external power supply to a closed environmental protected self-powered standalone unit. The HW changes in the product does not affect any of the RF parts and the RF characteristics of the originally certified product. No changes to the device PCB area with antennas, integrated cellular and Bluetooth LE modules. The automotive I/O, bus HW interfaces has been removed. The external automotive 12-24 V DC power supply has been exchanged with an internal long lasting non-rechargeable but exchangeable Li-metal battery pack operating at 3.6V DC voltage. The Li-Ion backup battery has been removed as no external power is available for charging. The integrated radio modules operational voltage remains unchanged. Trackunit Aps ________________________________________________________________________________________________ www.trackunit.com Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00 The SW has been modified to exclude all I/O and bus interfaces related to the automotive 2022-09-26 functionalities. The GSM functionality has been disabled by SW to increase battery life. Only 4G operation is available. The Class 2 Permissive Changed product TU600-21 will be the only product on the market. The following exhibits are associated with the C2PC changes performed on TU600-21:

1) User manual (Installation and safety) 2) Label and label placement document. 3) Internal pictures 4) External pictures 5) Block diagram 6) Schematics 7) Parts lists 8) Operational description If you have any questions, please feel free to contact me at the address shown below. Sincerely, Per Klaus Nielsen Certification Manager Trackunit Aps ________________________________________________________________________________________________ www.trackunit.com Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00

LONG-TERM CONFIDENTIALITY REQUEST for Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request Long-Term Confidentiality for the following product:

Grantee Code Equipment Product Code Check your GC here. Click Grantee Search. FCC ID:

For the product stated above, we request Long-Term Confidentiality for exhibits which contain Block Diagram, Operational Description, Parts List/Tune Up Info, Schematics, SDR Software/Security Info. The above exhibits contain our benefit to our competitors. This information will not be publicly available. trade secrets and proprietary information If you have any questions, please feel free to contact us at the address shown below. Sincerely, Company Name:

Company Address:

Contact Name:

Signature:

Phone:

Fax:

E-mail:

Signature Date:

that could be of Document Version 1.1 2020-10-30

Declaration about Hardware for TU600A family

(Integrated cellular module from Quectel)

2021-05-18

Issuer’s company name:

Issuer’s address:

Brand:

Product family :

Model(s):

Grants/Certificates:

Trackunit Aps

Gasvaerksvej 24, 4 sal

DK-9000, Aalborg

Denmark

Trackunit

TU600A

TU600-15, TU600-11

FCC ID: ZMF-TU600A

IC: 9746A-TU600A

We hereby declare that Product/Model(s): TU600-15, TU600-11 uses the module Product/Model:

BG95-M3 with FCC ID: XMR201910BG95M3 / IC: 10224A-2019BG95M3. No modifications of the

module (redesign, component replacements, PCB redesign) have been made.

Based on this fact conducted signal measurements of test reports (See list below) issued for

Product/Model: BG95-M3 also applies to Product/Model(s): TU600-15 and TU600-11

If you have any questions feel free to contact us at the address shown below

Signed on behalf of Trackunit Aps,

Per Klaus Nielsen

Certification Manager

Email: pkn@trackunit.com

BG95-M3 measurement reports Id’s:

- R2004A0249-R3 BG95M3 eMTC IC RSS-130_RSS-139.pdf

- R2004A0249-R7 BG95M3 NB-IOT IC RSS-130_RSS-139.pdf

- R2004A0249-R1 BG95M3 eMTC IC RSS-132.pdf

- R2004A0249-R4 BG95M3 eMTC IC RSS-132 LTE Band 26.pdf

- R2004A0249-R5 BG95M3 NB-IOT IC RSS-132.pdf

- R2004A0249-R2 BG95M3 eMTC IC RSS-133.pdf

- R2004A0249-R6 BG95M3 NB-IOT IC RSS-133.pdf

- R2003A0152-R1 YIYUAN BG95-M3 eMTC FCC Part22.pdf

- R2003A0152-R7 YIYUAN BG95-M3 eMTC FCC Part22 B26.pdf

- R2003A0152-R4 YIYUAN BG95-M3 NB-IOT FCC Part22.pdf

- R2003A0152-R2 YIYUAN BG95-M3 eMTC FCC Part24 .pdf

- R2003A0152-R5 YIYUAN BG95-M3 NB-IOT FCC Part24.pdf

- R2003A0152-R3 YIYUAN BG95-M3 eMTC FCC Part27.pdf

- R2003A0152-R6 YIYUAN BG95-M3 NB-IOT FCC Part27.pdf

- R2003A0152-R8 YIYUAN BG95-M3 eMTC FCC Part90 B26.pdf

Trackunit Aps

________________________________________________________________________________________________

www.trackunit.com

Gasværksvej 24, DK-9000 Aalborg, +45 96 73 74 00

2021-05-18

Trackunit Aps

________________________________________________________________________________________________

www.trackunit.com

Gasværksvej 24, DK-9000 Aalborg, +45 96 73 74 00

Declaration of integrated modules

(Manufacturers Declaration) Issuers company name:

Issuers address:

Trackunit Aps Gaesvaerksvej 24, 4 sal DK-9000, Aalborg Denmark Trackunit TU600-25, TU600-21, TU600-22 Brand:

Model(s):

We, Trackunit Aps hereby declares and ensures that under our sole responsibility that the Quectel module BG95-M3 with FCC ID: XMR201910BG95M3; IC: 10224A-2019BG95M3 is integrated in the Trackunit TU600-25, TU600-21 and TU600-22 without any electrical or mechanical changes. Secondly we, Trackunit Aps hereby declares and ensures that under our sole responsibility that the Silabs module BGM210P22A with FCC ID: QOQGM210P; IC: 5123A-GM210P is integrated in the Trackunit TU600-25, TU600-21 and TU600-22 without any electrical or mechanical changes. The modules integrated without modifications are shown in the component placement document. Signed on behalf of Trackunit Aps, 2022-02-07 Per Klaus Nielsen Certification Manager Email: pkn@trackunit.com Trackunit Aps ________________________________________________________________________________________________ www.trackunit.com Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00

May 17th - 2022 Federal Communication Commission Equipment Authorization Devision, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Industry Canada, Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 ATTESTATION STATEMENT

(Declaration on equivalent Models) TO WHOM IT MAY CONCERN We, Trackunit Aps declare on our sole responsibility that the tested model in CTC Advanced project 1-3523_21-01 TU600-25 with FCC ID: ZMF-TU600B, IC: 9746A-TU600B Is equivalent to the previous tested model in CTC Advanced project 1-1894_21-01:

TU600-15 with FCC ID: ZMF-TU600A, IC 9746A-TU600A with respect hardware and software covering the cellular/GNSS PCB antennas, the Quectel BG95-M3 cellular module, the Quectel L76-LB GPS/Glonass receiver, I/O ports, CAN bus and power supply. The only differences between the tested model TU600-25 and TU600-15 are the change of Bluetooth LE module to Silabs BGM210P22A from Silabs BGM13S22A. We attest that above variant changes are not relevant for the RF behaviour subject to the regulatory rules according to FCC part 2.1093, part 22, part 24, part 27 and part 90. Therefore, the CTC Advanced GmbH test reports for model TU600-15 in project 1-1894_21-

01 are all valid for the tested model TU600-25 as only partial testing is performed for the TU600-25 in project 1-3523_21-01. If you have any questions, please feel free to contact us at the address shown below Signed on behalf of Trackunit Aps Per Klaus Nielsen Certification Manager Email: pkn@trackunit.com Trackunit Aps _________________________________________________________________________________________ Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00 www.trackunit.com

March 22nd - 2022 Federal Communication Commission Equipment Authorization Devision, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 ATTESTATION STATEMENT

(Declaration on equivalent Models) TO WHOM IT MAY CONCERN We, Trackunit Aps declare on our sole responsibility that the models TU600-21, TU600-22 are equal in hardware and software to the tested model TU600-25 with FCC ID: ZMF-

TU600B to an extend not affecting the PCB layout with antennas, the Quectel BG95-M3 cellular module, the Silabs BGM210P22A Bluetooth LE module and the Quectel L76-LB GPS/Glonass receiver. The only differences between the model TU600-25 and the TU600-21 / TU600-22 are the baseband input/output interfaces and I/O ports:

1-wire/5V DC out interfaces:

CAN bus interface:

I/O ports:

not mounted. not mounted. not mounted. All TU600B family models are externally powered in the range from 12V DC to 48 V DC from a vehicles or machinery battery source. We attest that above variant changes are not relevant for the RF behaviour subject to the regulatory rules according to FCC part 2.1093, part 15.247, part 22, part 24, part 27 and part 90. Therefore, the CTC Advanced GmbH test reports for model TU600-25 are for applicable for the models TU600-21 and TU600-22. If you have any questions, please feel free to contact us at the address shown below Signed on behalf of Trackunit Aps Per Klaus Nielsen Certification Manager Email: pkn@trackunit.com Trackunit Aps _________________________________________________________________________________________ Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00 www.trackunit.com

Declaration about Hardware for TU600B family

(Integrated Bluetooth module from Silabs) 2022-03-22 Issuers company name:

Issuers address:

Brand name:

Product family :

Model(s):

Grants/Certificates:

Trackunit Aps Gasvaerksvej 24, 4 sal DK-9000, Aalborg Denmark Trackunit TU600B TU600-25, TU600-21, TU600-22 FCC ID: ZMF-TU600B IC: 9746A-TU600B We, Trackunit Aps hereby declare that Product/Model(s): TU600-25, TU600-21 and TU600-22 in the TU600B family uses the Bluetooth module Product/Model: BGM210P22A with FCC ID:

QOQGM210P / IC: 5123A-GM210P. No modifications of the module (redesign, component replacements, PCB redesign) have been made. Based on this fact the conducted signal measurements of reports:

Report no FCC Bluetooth LE_Hopping_RF190408C21 dated 2019-06-21 Report no FCC Bluetooth LE_DTS_RF190408C21-2 dated 2019-09-17 Report no IC Bluetooth LE_Hopping_IC190408C21 dated 2019-06-21 Report no IC Bluetooth LE_DTS_IC190408A21-2 dated 2019-09-17 issued for Product/Model: BGM210P22A also apply to Product/Model(s): TU600-25, TU600-21 and TU600-22. If you have any questions feel free to contact us at the address shown below Signed on behalf of Trackunit Aps Per Klaus Nielsen Certification Manager Email: pkn@trackunit.com Trackunit Aps ________________________________________________________________________________________________ www.trackunit.com Gasvrksvej 24, DK-9000 Aalborg, +45 96 73 74 00