Base-station user guide TriangleCNC Inc Base-station board user guide Page 1 / 8 Revision: 1.05 August 19, 2017 FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Table of contents 1. Hardware specification .................................................................................................................................................................. 3 1.1 General Specification ........................................................................................................................................................ 3 1.2 Hardware block diagram and dimension ................................................................................................................ 3 1) Block diagram.................................................................................................................................................................. 3 2) Board dimension ............................................................................................................................................................ 4 3) Description of connectors ......................................................................................................................................... 5 4) Description of switches ............................................................................................................................................... 6 5) Description of LEDs ...................................................................................................................................................... 6 2. Program status LED ......................................................................................................................................................................... 7 3. Interface for user .............................................................................................................................................................................. 8 1) Login the webpage of base-staation by using Internet Explorer ......................................................... 8 2) Login with default IP .................................................................................................................................................... 8 3) Login account .................................................................................................................................................................. 8 Base-station board user guide Page 2 / 8 1. Hardware specification 1.1 General Specification Item Description Product Input voltage 100 ~ 240VAC 50Hz/60Hz (external power source) Internal Input voltage DC12V (9 ~ 15V) (input voltage of board) Current OS Ethernet 300mA @12V Linux 10/100Mbps Internal connector
- RF module connector External connector
- RJ45 JACK (Ethernet 10/100Mbps) 1.2 Hardware block diagram and dimension 1) Block diagram Base-station board user guide Page 3 / 8 DC/DC Converter ICU11(RT8293BHGSP)Voltage Regulator ICU13(TPS79601DCQ)VDD_5P5V(5.4V)Voltage Regulator ICU14(TPS79601DCQ)VDD_5V(3.5V)+3V3(3.3V)MPUU5(AT91SAM9G25)+3V3(3.3V)12MHz XTAL/Y2/SMD3225Voltage SupervisorU3(LTC2918)+3V3(3.3V)LEDsDIP Switch & Rotary SwitchNAND FlashU7(S34ML01G100TF100)+3V3(3.3V)RS232 DriverU8(SP3232EEN)Debg CON (P1)V3P3D(3.3V)Socket(J3,J5)RF ModuleV3P3D(3.3V)VDD_5V(3.5V)AC/DC Adapter100 ~ 240VAC(50/60Hz)DC12VExternal Power Source100 ~ 240VACDC/DC Converter ICU3(AP3417CKTR-G1)DC/DC Converter ICU3(AP3417CKTR-G1)+3V3(3.3V)+3V3(3.3V)+1P8V(1.8V)+1V(1.0V)32.768kHz XTAL/Y3/CM200CPower switchU12(NC)(TPS2032DR)NC CON(J12)30MHz XTAL(8Y-30.000MEEQ-T)+1V(1.0V)DDR MemoryU6(MT47H64M16HR)+1P8V(1.8V)NC CON(J2,J4)10/100Mbps Ethernet TransceiverU9(DM9161BIEP)RJ45 CON(J6)BOX Header(J9)VDD_PHY(2.5V) 2) Board dimension Base-station board user guide Page 4 / 8 110.00145.00 3) Description of connectors Number Name Description A 12V Input connector
- Molex 5569-04A1 connector
- Pin number 1 : GND 2: GND 3: DC12 4: DC12V B C D E Debug connector
- D-SUB 9 straight
- RS232 2 Port RF Module connector
- 2.54mm Pin header Ethernet connector
- RJ45 JTAG connector
- 2x10 Box header Base-station board user guide Page 5 / 8 BACDE 4) Description of switches Number Name Description F G H Power switch Toggle switch Mode selection DIP switch 4Pin dip switch Mode selection rotary switch 10digit rotary switch 5) Description of LEDs Number Name Description I J Power status LED 3pi LED Program status LED Refer the next section Base-station board user guide Page 6 / 8 FGHIJ 2. Program status LED Blink when RF data is received Blink when data is received from the main server Aux blinking led CPU RUNNING 1 4 2 1 5 1 3 3 3 1 1 1 6 1 Blink when RF data is transmitted Blink when data is transmitted to the main server Base-station board user guide Page 7 / 8 3. Interface for user 3.1. Login into webpage 1) Login the webpage of base-staation by using Internet Explorer 2) Login with default IP Turn DIP switch #1 on, then supply power Login with 192.168.1.100 IP
-
-
3) Login account ID: ******
Password: ********
Base-station board user guide Page 8 / 8 This device must be professionally installed and maintained by TRIANGLECNC corp. It is not allowed ordinary people personally installing the device.