INSTALLATION Wiring diagram 220240 V 50 Hz L N L N
mm (AWG )
mm solid or stranded ein- oder mehrdrhtig monobrin a filo unico monofilar entrdig Dimensions US versions (28002800) Dimensions EU versions (28002801) 73,3 68.2 56 5 8 8 6
. 5 8 7 0 0 1 8 6 19.2 56 68,2 73,3 EU US RC 10/18-xxx-0 We reserve the right to make technical changes without prior notice. Tridonic GmbH & Co KG, www.tridonic.com, info@tridonic.com, Tel. +43 5572 395-0 Safety instructions Installation of this device may only be carried out by specialist staff who have provided proof of their skills. The power supply must be switched off before handling the device. The relevant safety and accident prevention regulations must be observed. Areas of application The device may only be used for the applications specified. for safe installation in dry, clean environment. be installed in such a way that access is only possible using a tool. UK basicDIM Wireless Sensor provides movement detection and lux control wire-
less to other basicDIM Wireless devices to achieve smart control as presence detection, daylight harvesting. Technical Data Rated supply voltage Rated supply voltage (US version) Mains frequency Detection range, mounted at height of 3 m Detection angle Light measurement at sensor head Radio transceiver operating frequencies Max. output power radio transceiver Operating temperature tc point Storage temperature Dimensions for integrated mounting Type of protection 220 240 V 120 277 V 50 / 60 Hz 6 m tbd 1 2,000 lx ( 20 %) 2.4 2.483 GHz
+ 4 dBM 0 ... +50 C 70 C
-40 ... +85 C 65 mm IP20 Installation Instructions Make sure that the mains voltage is switched off when making any connections. Use 0.75 2.5 mm (AWG 20 14) solid or stranded conductor electrical wires. Strip the wire 8 mm from the end. A This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, R Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. ist. D basicDIM Wireless Sensor 5DP 38RC (US) article number/Artikelnummer: 28002800 / 28002801 Insert the wires to the corresponding holes and tighten the connector screw. Mains input connector is marked with letters L and N. When installed at a height other than the recommended installation height
(3 m), the presence sensor might show different characteristics. When mounted at a higher level, its sensitivity is reduced. If mounted at a lower level, its range is diminished. Heaters, fans, printers and copiers located in the detection zone may cause incorrect presence detection. Optimal positioning of the sensor The sensor must be positioned on the ceiling so that the hands of the person using the room are in the centre of the detection zone without being covered by a screen, bodies and so on. Compatible devices Compatible with all Android 4.4 (KitKat) or later, iPhone 4S (iOS 5.0) or later and iPAD 3 (iOS 5.1) or later. Hereby, Tridonic declares that the radio equipment type basicDIM Wireless
(28002212) is in compliance with Directive 2014/53/EU. The full text is available at the following internet address:
http://www.tridonic.com/PDB/resources/TRCertPDF/42395_TA%20602_00.pdf T F Installationshinweise Achten Sie darauf, dass die Netzspannung abgeschaltet ist, wenn Sie Verbindungen herstellen. Verwenden Sie eindrhtige- oder mehrdrhtige Kabel mit einem Querschnitt von 0,751,5 mm. Isolieren Sie am Kabelende 67 mm ab. Drcken sie den Klemmendrcker nach unten und stecken Sie die Kabel in die dafr vorgesehenen ffnungen. Das basicDIM Wireless Passive Module wird ber den DALI Bus versorgt. Um die Funktion sicher zu stellen, ist es notwendig den DALI Bus extern zu ver-
sorgen. Es verfgt ber zwei Paar Klemmen. Die Paare sind intern, parallel verbunden. Dadurch kann eine Durchgangsverdrahtung einfach realisiert werden. Die Anschlsse sind mit DA1 und DA2 gekennzeichnet. Kompatible Gerte Kompatibel mit Android 4.4 (KitKat) oder hher, iPhone 4S (iOS 5.0) oder hher und iPAD 3 (iOS 5.1) oder hher. Hiermit erklrt Tridonic, dass der Funkanlagentyp basicDIM Wireless Passive Module (28002574) der Richtlinie 2014/53/EU entspricht. Der vollstndige Text ist unter der folgenden Internetadresse verfgbar:
http://www.tridonic.com/PDB/resources/TRCertPDF/42395_TA%20602_00.pdf Einsatzbereich Das Gert darf nur fr den bestimmungsgemen Einsatz verwendet werden. muss fr eine sichere Installation in einer trockenen, sauberen Umgebung muss so installiert werden, dass der Zugang nur mit einem Werkzeug mglich installiert werden.