all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
Setup and Installation | Users Manual | 863.66 KiB | ||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | Internal Photos | |||||||
1 2 3 | ID Label/Location Info | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Test Setup Photos | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Internal Photos | native | ||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Setup Photos | |||||||
1 2 3 | Test Report |
1 2 3 | Setup and Installation | Users Manual | 863.66 KiB |
SkyPilot by Trilliant Gateway Pro Installation and Setup SP-5XXX Preliminary
| i 671-00XXX-01 Rev A Draft 1 2012 Trilliant, Inc. All rights reserved This publication, or parts thereof, may not be reproduced in any form, by any method, for any purpose. Product specifications are subject to change without notice. This material is provided for informational purposes only; Trilliant assumes no liability related to its use and expressly disclaims any implied warranties of merchantability or fitness for any particular purpose. Trilliant Trademarks Trilliant, CellReader, CellGateway, SecureMesh, SerViewCom, UnitySuite, SkyPilot, SyncMesh, the Trilliant logo, and the SkyPilot logo are trademarks of Trilliant Incorporated and/or its subsidiaries. All other trademarks are the property of their respective owners. This material is provided for informational purposes only; Trilliant assumes no liability related to its use and expressly disclaims any implied warranties of merchantability or fitness for any particular purpose. All specifications, descriptions, and information contained herein are subject to change without prior notice. Third-Party Trademarks Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. MySQL is a registered trademark of MySQL AB in the United States, the European Union, and other countries. All other designated trademarks, trade names, logos, and brands are the property of their respective owners. Third-Party Software Program Credits This product includes software developed by the Apache Software Foundation (http://www.apache.org/), licensed under the Apache License. This product includes the DHCP Server software from Internet Systems Consortium, licensed under the DHCP License. The DHCP Server software is copyright 2004 Internet Systems Consortium, Inc. (ISC). Copyright 19952003 Internet Software Consortium. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of ISC, ISC DHCP, nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY INTERNET SYSTEMS CONSORTIUM AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ISC OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes the FTP Server software from vsftpd (http://vsftpd.beasts.org/), licensed under the GNU General Public License. This product includes Java software from Sun Microsystems, licensed under Sun Microsystems' Binary Code License Agreement. Copyright 2003, Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Sun, Sun Microsystems, the Sun logo, Solaris, Java, the Java Coffee Cup logo, J2SE, and all trademarks and logos based on Java are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. This product includes JBOSS Version 3.2.3 software from JBoss, licensed under the GNU Lesser General Public License. Some bundled products in JBOSS are licensed under the Apache License. This product contains Java Telnet Application (JTA 2.0). This product contains the MibBrowser software from Mibble. This product includes software the copyright of which is owned by and licensed from MySQLAB. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/). Copyright (c) 19982005 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/) 4. The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org. 5. Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/). THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes libraries developed by Eric Young and is licensed under the Original SSLeay License. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Copyright (C) 19951998 Eric Young (eay@cryptsoft.com). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) The word
'cryptographic' can be left out if the routines from the library being used are not cryptographic related :-). 4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: This product includes software written by Tim Hudson (tjh@cryptsoft.com). THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes SNMP software from WestHawk, licensed under the WestHawk License. This product includes JFreeCharts from http://www.jfree.org/, licensed under GNU Lesser General Public License. This product includes JasperReports from http://jasperreports.sourceforge.net/index.html, licensed under GNU Lesser Public License. ii |
Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Audience and Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi How This Guide Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . vi Conventions Used in This Guide . . . . . . . . . . . . . . . . . . . . . . .vii Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Solution Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Mesh Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SkyPilot Gateway & SkyPilot Gateway Pro . . . . . . . . . . . . . . . . . 4 SkyPilot Extender, Extender DualBand . . . . . . . . . . . . . . . . . . . 4 SkyPilot Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Your SkyPilot Gateway Pro Kit . . . . . . . . . . . . . . . . . . 7 Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Required Tools and Supplies. . . . . . . . . . . . . . . . . . . . . . . . . . 9 Planning Your SkyPilot Network . . . . . . . . . . . . . . . 11 Deployment Process Overview . . . . . . . . . . . . . . . . . . . . . . . 12 Network Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Co-Located SkyPilot Gateway Pro Devices . . . . . . . . . . . . . . . . 16 Configuring the SkyPilot Gateway Pro. . . . . . . . . . . . 17 Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Powering Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Configuring the SkyPilot Gateway Pro. . . . . . . . . . . . . . . . . . . 22 Configuring Adjacent SkyPilot Gateway Pros . . . . . . . . . . . . . . 26 Installing the SkyPilot Gateway Pro . . . . . . . . . . . . . 27 Install Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Verifying Connectivity . . . . . . . . . . . . . . . . . . . . . . 33 Confirming SkyPilot Gateway Pro Connectivity . . . . . . . . . . . . . 33 Confirming SkyPilot Extender and SkyPilot Connector Connectivity 35 Confirming SkyPilot Extender DualBand Access Point Connectivity 37 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Appendix A Grounding Guidelines . . . . . . . . . . . . . . . . . . . . . . 41 General Grounding Strategy . . . . . . . . . . . . . . . . . . . . . . . . . 41 Adding Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Grounding Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Appendix B FCC Statements . . . . . . . . . . . . . . . . . . . . . . . . . . 45 FCC Class A Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 FCC Class B Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maximum Permissible Exposure . . . . . . . . . . . . . . . . . . . . . . 46 FCC 15.203 statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Contents | iii Regulatory Statements for Canada . . . . . . . . . . . . . . . . . . . . . 46 Appendix C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Appendix D Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 RJ-45 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 DB-9 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 iv |
Contents About This Guide This guide explains how to install and set up a SkyPilot Gateway Pro device. It assumes administrator-level knowledge of IP networks and a familiarity with configuring wireless devices. Chapter Highlights Audience and purpose How this guide is organized Conventions used in this guide
| v Audience and Purpose This guide provides directions for installing and setting up a SkyPilot Gateway Pro. This guide assumes administrator-level knowledge of IP networks and a familiarity with configuring wireless devices. How This Guide Is Organized This guide is organized as follows:
Chapter 1, Introduction, provides an overview of the SkyPilot solution, describes the SkyPilot devices, and then illustrates how they combine to form a mesh network. Chapter 2, Your SkyPilot Gateway Pro Kit, provides the information you need before you begin your installation. Chapter 3,Planning Your SkyPilot Network, provides an overview of network planning guidelines and procedures Chapter 4, Configuring the SkyPilot Gateway Pro, describes the process for bringing up a SkyPilot Gateway Pro unit for the first time. Chapter 5, Installing the SkyPilot Gateway Pro, explains how to mount the unit in the field. Chapter 6, Verifying Connectivity,describes the steps needed to verify proper operation of each device. Appendix A, Grounding Guidelines, provides direction on protecting your SkyPilot device with proper grounding and surge protection. Appendix B, FCC Statements, provides the FCC radio frequency interference statements for the SkyPilot Gateway Pro devices. Appendix C, Specifications, give the mechanical and electrical specifications of the SkyPilot Gateway Pro. Appendix D, Pinouts, provides pinouts for connectors and adapters to connect to the Ethernet interface port labeled CPE on the SkyPilot Gateway Pro power supply and the devices serial interface. vi |
About This Guide Conventions Used in This Guide This section describes the text and syntax conventions used throughout this guide. Text Conventions This guide uses the following text conventions:
Italic is used to introduce new terms. Bold is used to indicate what you click or type in a graphical user interface (for example, commands names or text being entered). In examples showing user interaction with the command-line interface, bold is used to indicate user input as opposed to command output. A monospace font is used for code elements (variable names, data values, function names, and so forth), command lines, scripts, and source code listings. Italic-monospace is used for replaceable elements and placeholders within code listings. Syntax Conventions This guide uses the following conventions when showing syntax:
Angle brackets, < and >, enclose mandatory elements. You must enter these elements. For example:
ping <IP-address>
Square brackets, [ and ], enclose optional elements. You can omit these elements. For example:
show filter [filter-table-number]
Square brackets are also used to show the current value of parameters in the output of some commands. A vertical bar, |, separates choices. For example:
show bridge [cache | port]
Conventions Used in This Guide | vii viii |
About This Guide Introduction This chapter provides an overview of the SkyPilot Networks solution, describes the SkyPilot devices, and then illustrates how they combine to form a mesh network. 1 Chapter Highlights Solution Overview Mesh Network SkyPilot Gateway and SkyPilot Gateway Pro
| 1 Solution Overview A SkyPilot Network delivers a wireless, end-to-end broadband solution that seamlessly supports high-capacity, high-coverage mesh networks. Designed for managed-access networks and service providers, the SkyPilot network takes broadband wireless the last mile with a cost-effective, robust infrastructure solution. Based on a high-performance architecture that includes intelligent antenna arrays, the SkyPilot network delivers a dynamic broadband solution. SkyPilot wireless devices are simple to install and easily fit into any type of wireless environmentmetropolitan, business, or home. The auto-discovery and rapid provisioning features of a SkyPilot wireless mesh network can greatly reduce deployment and maintenance costs. Multiple topology options and network scalability create intriguing options for rapidly expanding a metro Wi-Fi customer base. Mesh Network The typical configuration for a SkyPilot network is a mesh topology, which uses SkyPilot Extenders to extend range and add network flexibility. In a mesh configuration, subscribers can either connect directly to the SkyPilot Gateway Pro or connect indirectly via SkyPilot Extenders (see Figure 1-1). In addition to adding range, a mesh network allows connections from locations where obstructions prevent line-of-sight access to a SkyPilot Gateway Pro. Mesh networks are ideal for dense subscriber environments, for filling in coverage holes, and for reaching subscribers in areas where RF communication is obstructed by hills, trees, buildings, or other obstacles. 2 | Chapter 1 Introduction Figure 1-1. SkyPilot wireless mesh network SkyPilot Extender Adds a Wi-Fi access point providing 802.11 wireless access to the mesh network in metropolitan hot zones. Wi-Fi zone SkyPilot Connector SkyPilot Extender SkyPilot Extender SkyPilot Extender SkyPilot Extenders increase the coverage footprint by extending the wireless mesh network beyond the range of the SkyPilot Gateway Pro. SkyPilot Extender Provides broadband Internet access via Wi-Fi and supports public safey applications such as video surveillance. SkyPilot Connector SkyPilot Connectors link subscribers to the wireless mesh network via an Ethernet port that allows connection from a PC or a local area network. SkyPilot Gateway Pro Internet Mesh Network | 3 SkyPilot Gateway & SkyPilot Gateway Pro The SkyPilot Gateway and Gateway Pro operate as a base stations for a wireless mesh network. They provide an interface between the wired infrastructure and a wireless network of subscribers who enjoy secure, high-speed access to the Internet. A SkyPilot wireless network requires at least one SkyPilot Gateway or SkyPilot GatewayPro, for operation. If necessary, you can add additional SkyPilot Gateway Pros to increase network capacity or provide redundancy. A SkyPilot Gateway or Gateway Pro resides at a location with easy access to wired infrastructureusually a POP (point of presence) or data center. The SkyPilot Gateway Pro uses an advanced, second-generation electronically steerable antenna to deliver higher overall throughput. In addition, it XXX... SkyPilot Extender, Extender DualBand SkyPilot Extenders and SkyPilot Extender DualBands provide a cost-effective way to extend range and balance network loads by operating as repeaters to extend the wireless range of a SkyPilot Gateway Pro (see Figure 1-1). You can add a SkyPilot Extender device to your network to expand your coverage footprint and provide redundancy through SkyPilots mesh networking features. SkyPilot Extender devices, including DualBands, can provide subscribers with a direct connection to the wireless network via the devices Ethernet port. SkyPilot Extender DualBand is a dual-radio solution that combines SkyPilots long-
range, high-capacity 5 GHz mesh backhaul with a high-powered 2.4 GHz 802.11b/g access point that allows service providers and municipalities to offer standard Wi-Fi services, for targeted hot zones or ubiquitous coverage patterns. For optimum performance, install the SkyPilot Extender in an elevated location such as a roof, tower, or utility pole. 4 | Chapter 1 Introduction SkyPilot Connector SkyPilot Connectors link your subscribers to the SkyPilot wireless network. An Ethernet port on the device allows a connection to a subscribers computer, or to a local area network (LAN) via a data switch or router. Designed for installation by the service provider, the SkyPilot Connector attaches to an external structure such as an eave, roof, or pole. The SkyPilot Connector DualBand offers the same features as a SkyPilot Connector, plus a Wi-Fi access point that enables service providers and municipalities to provide standard 802.11 wireless access, for targeted hot zones, or for dense coverage patterns. SkyPilot Connector | 5 6 | Chapter 1 Introduction Your SkyPilot Gateway Pro Kit Your SkyPilot Gateway Pro kit provides the basic equipment you need to install the device and configure it for operation on a SkyPilot wireless mesh network. This chapter describes that equipment and lists additional items you should have on hand before starting installation. 2 Chapter Highlights Kit Contents Required Tools and Supplies
| 7 Kit Contents The contents of the SkyPilot Gateway Pro kit are listed below:
SkyPilot Gateway Pro unit Power supply. This unit is both a power supply and a power injector. Your SkyPilot Gateway Pro is powered over Ethernet, and you may use either the included power supply or your own PoE PSE equipment. Note that the power supply is not outdoor-ratedl it should be mounted indoors or in a suitable enclosure. DB-9 to RJ-45 adapter. This can be used to adapt the cat-5 serial port cable to a DB-9 serial port. GPS antenna GPS antenna mounting bracket Weatherproof cable connector housing Mounting hardware, consisting of:
two sets of two-piece pole clamps double-hinged mounting bracket single-hinged mounting bracket Nuts, bolts, and washers 8 | Chapter 2 Your SkyPilot Gateway Pro Kit Figure 2-1. SkyPilot Gateway Pro (rear view) Required Tools and Supplies Before starting installation, you also need the following:
For basic mounting:
7/16" wrench 9/16 wrench Phillips screwdriver Loc-tite or other thread-locking compound For pole mounting:
Magnetic level Steel pole between 1 1/4" and 2 1/8" in diameter For network cabling:
Spool of CAT-5 shielded network cable, outdoor-rated. RJ-45 straight through cable for a serial connection to a console (standard CAT-5 patch cable will work) Required Tools and Supplies | 9 NOTE In theory, you should never need to service a unit once it is deployed. However, should you need to do so, access to the serial port may be required. Many installers find it prudent to run a serial cable from the SkyPilot to a location that gives easier access. Crossover cable (for connecting to a an access point, switch, or router) RJ-45 unshielded connectors (connectors without a protective plastic boot are preferred; they fit through the cable clamp more easily.) RJ-45 crimping tool Open-end wrench, adjustable or 1-3/6 (30 mm) Surge protection device (strongly recommended) For configuration:
Computer with a serial port, a terminal emulation program, a network interface card, and a Web browser. A laptop recommended for convenience. 10 | Chapter 2 Your SkyPilot Gateway Pro Kit Planning Your SkyPilot Network This chapter provides instructions for configuring the SkyPilot Gateway Pro and then performing the physical installation. 3 Chapter Highlights Planning your installation GPS and the SkyPilot Gateway Pro
| 11 Deployment Process Overview Table 3-1 summarizes the stages of SkyPilot network planning and deployment. Table 3-1. Stages of deployment Stage Description Identify equipment locations Identify and prepare locations for installation. Choose an operating frequency Choose a clean center frequency that permits interference-free operation of devices. Provision SkyPilot devices Choose a provisioning mode for the devices: manual or automatic. Provision the devices. (For automatic provisioning, install operating system and SkyPilot EMS software.) Install SkyPilot devices Install the devices, beginning with SkyPilot Gateway Pro devices and building out. Verify connectivity Confirm that the SkyPilot Gateway Pro is online. Confirm that installed SkyPilot Connectors and SkyPilot Extenders have established a link with the SkyPilot Gateway Pro. Review link characteristics and network performance. Network Planning Identify Equipment Locations Deployment of a SkyPilot network starts with a site survey to help you identify the devices you need and choose optimum locations for installation. Identifying locations for the SkyPilot Gateway Pro and SkyPilot Connectors is straightforward. For the SkyPilot Gateway Pro, location depends on proximity to existing network infrastructure and site elevation. SkyPilot Connectors are placed at subscriber siteshomes or offices. 12 | Chapter 3 Planning Your SkyPilot Network When choosing a site for the SkyPilot Gateway Pro, consider the radio frequency
(RF) environment and the physical layout of the area. Trees, buildings, and hills can attenuate or block a wireless signal. When assessing a site, examine the overall topology of the wireless path for obstructionsboth existing and plannedas well as seasonal changes of foliage and tree growth. The RF environment is dynamic, and can deteriorate over time as structures appear or are relocated. Plan to use test signals to determine the suitability of the link topology for target applications. Interference on your desired frequency results in overlapping signals, causing outages or intermittent drops in throughput. Once youve identified a potential site, use a topographic map or path profile software to ensure that terrain or obstacles will not interfere with the links. Numerous online tools for RF path analysis are available. These can also help identify possible Fresnel zone issues. Your site survey should include an RF scan to identify available frequencies. You should also check your preferred frequency at all locations. A frequency thats clear at one location may be crowded at another. Frequency planning is a critical factor in planning and implementing a wireless network. (For device operating frequencies, see Appendix C, Specifications.) The site survey process should be ongoing. To verify that a site is relatively free of interference, make site audits every six to twelve months, scheduling regular maintenance visits to coincide with the site audits. In a typical wide area wireless mesh network, youll install a SkyPilot Gateway Pro on the side of a building. The direct coverage area of the SkyPilot Gateway Pro is usually proportional to the height of the installation. You can also set up a SkyPilot Gateway Pro for use in smaller-scale networksfor example, a high-capacity business, an academic campus interconnection, or a local access network. SkyPilot Extenders are far more flexible in terms of location. If you determine that you need SkyPilot Extenders in order to reach all your customers or add redundancy, you must also identify optimum locations for their installation. Network Planning | 13 GPS and the SkyPilot Gateway Pro The SkyPilot Gateway Pro uses a GPS (Global Positioning System) signal for synchronization with other SkyPilot devices on the network. The strongest GPS signal is available outdoors, where the device has an unobstructed view of the sky.
(For indoor installations, such as for configuration and testing, the optimum location is on a windowsill or other opening with access to the sky.) A separate GPS antenna is included with your SkyPilot Gateway Pro. It should be mounted above the SkyPilot Gateway Pro, where is has a clear view of the sky. Upon startup, a SkyPilot Gateway Pro searches for a GPS signal, and if the device cant detect a signal, it will be unable to complete startup and wont establish wireless connections with other devices. You can configure a SkyPilot Gateway Pro even if the device cant detect a GPS signal. While the device is searching for the GPS signal, press the TILDE key (~) to bypass the search; the device will then proceed through the startup sequence. NOTE The GPS search should be bypassed only for device configuration, not for standard operation. Without a GPS signal, data will not be reliably transmitted between devices. The LEDs on the base of the device will confirm availability of a GPS signal. Guidelines for Adding SkyPilot Extenders Multiple factors can affect wireless network performanceand dictate the need for SkyPilot Extenders. Physical distanceAre all your subscriber sites close enough to the SkyPilot Gateway Pro for radio communications? If a SkyPilot Gateway Pro is installed in a high location with a clear sight line to subscriber sites, it can maintain radio communications with SkyPilot Connectors or SkyPilot Extenders at greater distances. ElevationThere is a correlation between range and device elevation. By installing SkyPilot devices on raised locations, such as towers or tops of buildings, you can avoid RF obstructions that can occur at ground level, thereby extending the range at which the devices can operate normally. 14 | Chapter 3 Planning Your SkyPilot Network You should install SkyPilot devices at similar elevation because large elevation differences may have an adverse impact on signal strength. ObstructionsAn optimum link between a SkyPilot Gateway Pro and a SkyPilot Connector requires a clear line of sight. Obstructions, both artificial and natural, can reduce effective network range or block radio communications entirely. Type of SkyPilot ConnectorBecause its typically placed outside and at higher elevation than the indoor connector, the outdoor version of the SkyPilot Connector provides greater wireless range than the indoor version. If there are obstructions blocking subscriber access (as in Figure 3-1) or if there are subscriber sites beyond the distance that a wireless link can maintain, you need to add one or more SkyPilot Extenders to the network. Figure 3-1. Using a SkyPilot Extender for network extension behind an obstruction Network Planning | 15 Preparing SkyPilot Extender Sites If SkyPilot Extenders are required, perform a survey of possible sites before beginning installation. For a detailed discussion of site requirements, refer to SkyGateway/SkyExtender Installation and Setup. For optimum service, attach SkyPilot Extenders to elevated, fixed locations with easy and continuous access to power. Choose an Operating Frequency All the devices on a SkyPilot network operate on a single frequency. Before beginning the installation, visit the deployment area and identify an optimum operating frequency. Use a spectrum analyzer or other frequency-planning tool to identify the best available frequency for the SkyPilot wireless networka clean center frequency that permits interference-free operation of devices. Co-Located SkyPilot Gateway Pro Devices If you put two of em together, you..... 16 | Chapter 3 Planning Your SkyPilot Network Configuring the SkyPilot Gateway Pro This chapter provides instructions for configuring the SkyPilot Gateway Pro and then performing the physical installation. You should test and configure you SkyPilot Gateway Pro on the bench before deploying it to the field. To do so, you will need to connect cables and the GPS antenna. 4 Chapter Highlights Cabling Powering up Configuring the SkyPilot Gateway Pro Accessing the command-line interface Provisioning To provision your SkyPilot Gateway Pro, you must:
Choose a provisioning mode: automatic or manual. Prepare the network infrastructure. For automatic provisioning, you must install SkyPilot software on a supported operating system to create your Network Management System (NMS) Provisioning | 17 Cabling Ethernet cabling provides power and data connectivity for the SkyPilot Gateway Pro. Serial cabling provides connectivity for troubleshooting and local configuration. Figure 4-1. Cable Connections and Mounting Holes GPS Mount Holes Upper Mount Holes Lower Mount Holes Ground Lug Ethernet Jack Serial Port Serial Port Access Hole Cable Clamp GPS SMA Connector To install cabling for Ethernet, and optionally serial connections:
1 Remove the access plate from the back of the unit. 2 Connect the Ethernet cable. a Unscrew the black cable clamp and remove the grey rubber gasket. b Thread your Ethernet cable through the black plastic cap and then the grey gasket. In most cases, you can fit the RJ-45 plug through the gasket, or you can thread the cable through first and them crimp on a connector. 18 | Chapter 4 Configuring the SkyPilot Gateway Pro c Thread the Ethernet cable through the connector body and plug it into the RJ-45 receptacle on the circuit board. d Makes sure there is a little slack in the cable inside the unit, to act as a strain relief. e Insert the grey gasket back into the connector, and then tighten the cap until the cable is securely held. 3 Connect the serial cable. This is done in the same manner as the Ethernet cable. You must first remove the plug and installed the supplied cable clamp. The plug unthreads; use a large flat-blade screwdriver or a coin. 4 Re-attach the cover. 5 Use cable ties or Velcro wraps to secure all the cabling against strain. Figure 4-2. Exploded View of Cable Clamp Assembly Rubber Plug Nut Cat 5 Cable Cabling | 19 GPS Antenna 1 Attach the GPS antenna bracket to the top of the unit, on the back, using two small Phillips screws. This is shown in Figure 4-3. 2 Connect the GPS antenna cable to the SMA connector on the unit bottom. 3 4 The GPS antenna is magnetic, and will stick to the mounting bracket. Temporarily place the GPS antenna where it can pick up a GPS signal. You can use a hand-held GPS device, such as an iPhone, to determine if there is adequate signal strength in your location. Figure 4-3. GPS bracket 20 | Chapter 4 Configuring the SkyPilot Gateway Pro Powering Up 1 Connect a power cord to the power supply, and plug it in. 2 Connect the Ethernet cable from the SkyPilot Gateway Pro to the port labeled Output on the power supply. 3 Connect an Ethernet cable from the port labeled Input to your network. Monitoring the Power-On Sequence When the SkyPilot Gateway Pro is powered up, it starts a power-on sequence. You can monitor itby observing the pair of LED lights on the back of the device. The power-on sequence may take up to 15 minutes, depending on how quickly the device can acquire a GPS signal. NOTE The SkyPilot Gateway Pro must have access to a GPS signal to complete its power-on sequence and start making wireless network connections. Depending on your SkyPilot network configuration, the device may be unable to connect to the network until the device has been configured. Table 4-1 provides detailed descriptions of device states indicated by the LEDs.. Table 4-1. SkyPilot Gateway Pro LED Status Lights Device state LED 1 (left) LED 2 (right) Startup in progress Slow staggered blinking of both LEDs Startup failure Off On Initializing image, acquiring GPS signal Blinks 4 times;
repeats Blinks 4 times;
repeats Initialization failure Fast, synchronized blinking of both LEDs Successful initialization, but authorization failure Successful initialization, but no links found Connected Green Green Green Off
Blue Powering Up | 21 Configuring the SkyPilot Gateway Pro To operate on the wireless mesh network, the SkyPilot Gateway Pro requires a network configuration. A SkyPilot Gateway Pro will not transmit a wireless signal until it is configured, and it will not be able to connect to other network devices without a configuration. SkyPilot offers two modes for provisioning devices with a configuration:
AutomaticRequires the use of SkyPilot EMS software to create configurations that an unattended central server can distribute to devices on the wireless mesh network. Although automatic provisioning requires more initial setup time than manual provisioning, it greatly simplifies the administration of a growing network. Detailed procedures for using EMS software are provided in SkyPilot Network Administration, available from the SkyPilot website at www.skypilot.com/support/. ManualManual provisioning permits the configuration of only a single device at a time, creating the minimum settings required for a wireless link and storing them in the devices flash (nonvolatile) memory. Manual provisioning is a logical choice if youre installing a test network or rolling out a small-scale installation that isnt expected to expand. For more information about provisioning modes, refer to Getting Started with the SkyPilot Network, available from the SkyPilot website at www.skypilot.com/support/. Accessing the Command-Line Interface SkyPilot devices include a command-line interface which you can use for manual provisioning and troubleshooting. You can connect to a device and access its command-line interface through Telnet over an Ethernet connection or via a terminal session from a console connected to the devices RJ-45 serial port. The default IP address is 192.168.0.2 After logging in (user: admin; password: public), you can enter commands at the command prompt. 22 | Chapter 4 Configuring the SkyPilot Gateway Pro For detailed access instructions for the command-line interface, refer to the SkyPilot Command-Line Interface Reference. Manually Provisioning Devices Manual provisioning stores settings in the devices flash memory, where they remain available for recall when the device starts up. NOTE If youre installing a device in a location that poses difficulties, consider delaying the final mounting until you can confirm that provisioning was successful. Table 4-2 summarizes the steps required to manually provision a device. Table 4-2. Manually Provisioning a Device (Page 1 of 2) Step Refer to 1 2 3 Decide whether to provision the device using the command-line interface or the Web interface.
(For DualBand/ access points, you must use the Web interface.) Prepare the device for installation by installing the necessary cabling, attaching antennas (for DualBands), and readying the device for service. Do not install the device yet. Choosing a Manual Provisioning Method in SkyPilot Network Administration The appropriate installation manual:
SkyGateway/SkyExtender Installation and Setup SkyConnector Indoor Installation SkyConnector Outdoor Installation Power on the device. Configuring the SkyPilot Gateway Pro | 23 Table 4-2. Manually Provisioning a Device (Page 2 of 2) Step Refer to 4 5 6 7 8 9 The appropriate interface reference manual:
SkyPilot Command-Line Interface Reference SkyPilot Web Interface Reference Either of the following provisioning tool references, making sure to set at least the minimum provisioning parameters (refer to Required Provisioning Parameters and in SkyPilot Network Administration):
SkyPilot Command-Line Interface Reference SkyPilot Web Interface Reference SkyPilot Web Interface Reference Connect a computer to the device and access the command-line interface or the Web interface.
(For DualBands, this step refers to the SkyPilot Extender portion of the device.) Provision the device.
(For DualBands, this step refers to the SkyPilot Extender portion of the device.) For DualBands, reboot the device, connect a computer to the devices 2.4 GHz access point, and provision the access point. Power off the device. Complete the installation. The appropriate installation manual:
SkyGateway/SkyExtender Installation and Setup SkyConnector Indoor Installation SkyConnector Outdoor Installation Power on the device. 24 | Chapter 4 Configuring the SkyPilot Gateway Pro Automatically Provisioning All Network Devices Table 4-3 summarizes the steps required to automatically provision all devices on a network. Although its possible to provision SkyPilot devices in any order, by following this sequence you can ensure that devices are able to form links as soon as they come online. Table 4-3. Automatically Provisioning All Network Devices (Page 1 of 2) Step Refer to 1 2 3 4 The appropriate installation manual:
SkyPilot OS Installation: Red Hat Linux 9.0 SkyPilot OS Installation: Fedora Core 2 and 4 SkyPilot OS Installation: Red Hat Enterprise Linux ES 3 and 4 SkyPilot EMS Installation Adding Devices to the DHCP Configuration File in SkyPilot Network Administration For new SkyPilot network deployments, custom-
install the operating system software on the SkyPilot EMS server. For new SkyPilot network deployments, install the server component of SkyPilot EMS, and then install the client component of SkyPilot EMS on any appropriate computer. For new SkyPilot Gateway Pros, set up the DHCP server and, if the provisioning server is behind a firewall, specify ports for data traffic between the server and SkyPilot devices. Provision the SkyPilot Gateway Pro(s). The following automatic provisioning topics in SkyPilot Network Administration:
Provisioning a Device Starting SkyProvision SkyProvision Display Pane Searching for Configured Devices Configuring the SkyPilot Gateway Pro | 25 Table 4-3. Automatically Provisioning All Network Devices (Page 2 of 2) Step Refer to 5 6 7 8 9 10 11 For new SkyPilot Gateway Pros, complete the installation and power it on.
(Optional) Log in to the SkyPilot Gateway Pro and configure the management VLAN. SkyGateway/SkyExtender Installation and Setup The SkyPilot EMS Interface in SkyPilot Network Administration Provision the SkyPilot Extender(s). The following automatic provisioning topics in SkyPilot Network Administration:
Provisioning a Device Starting SkyProvision SkyProvision Display Pane Searching for Configured Devices For information about access point settings, refer to SkyPilot Network Administration. For configuration procedures, refer to the SkyPilot Web Interface Reference SkyGateway/SkyExtender Installation and Setup Same as for step 7. The appropriate installation manual:
SkyConnector Indoor Installation SkyConnector Outdoor Installation For DualBands, provision the access point(s). For new SkyPilot Extenders, install the device and power it on. Provision the SkyPilot Connector(s). For new SkyPilot Connectors, install the device and power it on. Configuring Adjacent SkyPilot Gateway Pros is quite tricky.... 26 | Chapter 4 Configuring the SkyPilot Gateway Pro Installing the SkyPilot Gateway Pro This chapter provides instructions for configuring the SkyPilot Gateway Pro and then performing the physical installation. 5 Install Devices You can ensure optimum operationand reduce administrative overheadby installing your network devices in this order:
SkyPilot Network Management System SkyPilot Gateway Pro SkyPilot Extenders (optional) SkyPilot Connectors. You install the SkyPilot Gateway Pro first because, as the base station of the SkyPilot wireless network, it must be present in order for other devices to establish network links. When provisioned and powered on, the SkyPilot Gateway Pro immediately starts transmitting hello beacons that SkyPilot Extenders and Sky Connectors use to form links. After installing the SkyPilot Gateway Pro, you add SkyPilot Extenders (if required) and then SkyPilot Connectors. Upon powering on, each device responds to the base stations hello beacon and starts forming links with the SkyPilot Gateway Pro. Each device attempts to establish as many links as possible before choosing an optimum path. After establishing network links, SkyPilot Extenders on your network also begin transmitting hello beacons, extending the range of beacons available to other devices. (SkyPilot Connectors do not transmit hello beacons.) Install Devices | 27 Mounting The SkyPilot Gateway Pro uses two hinged mounting brackets to allow it to be tilted up or down slightly, as needed. Figure 5-1. Mounted SkyPilot Gateway Pro
. To mount the SkyPilot Gateway Pro:
IMPORTANTIt is the installers responsibility to verify that the support pole and its installation method are of sufficient strength to withstand onsite weather conditions. (The supplied mounting bracket and screws are certified to withstand a 150 mph wind force.) 1 Attach one of the pole-clamp assemblies to the pole at the height you want for the top of the unit. Make sure the threaded holes are facing up. Use the long bolts in the kit. 28 |
5 Installing the SkyPilot Gateway Pro Figure 5-2. Pole Clamps: Top View at Left; Bottom View at Right 2 Attach the second pole-clamp assembly to the pole, about nine inches lower than the first. Again, make sure the threaded holes are facing up. Figure 5-3. Pole Clamps Attached to Pole 3 Attach the hinged brackets to the SkyPilot Gateway Pro using the supplied 1/4-28 UNC bolts. These have hex heads. Do not use the Phillips-head screws. Use thread-locking compound. Mounting | 29 The brackets should be attached so that the body of the bracket is below the mounting holes. This, in turn, will orient the hook-tab, which is at the other end of the bracket, down. IMPORTANTThe double-hinged mounting bracket and the single-hinged bracket , together, allow you to tilt the unit. If you need to tilt it down, use the double-hinged bracket on top. If you need to tilt it up, use the double-hinged bracket on the bottom. IMPORTANTThe holes in the unit are fine-thread. DO NOT use 1/4-20 UNC
(coarse thread) hardware in these holes. IMPORTANTThe SkyPilot Gateway Pro case is aluminum. Do no over-torque the mounting bolts. NOTE Your SkyPilot Gateway Pro can be wall-mounted. You will need lag bolts or other fasteners suitable for attaching to the wall. Use them to attach one-
half of the pole clamp to the wall, then hang the SkyPilot Gateway Pro as described below. Figure 5-4. SkyPilot Gateway Pro with Mounting Brackets Attached GPS antenna on bracket 1/4-28 hex-head bolts Double-hinge bracket Tab Single-hinge bracket 30 |
5 Installing the SkyPilot Gateway Pro 4 The SkyPilot Gateway Pro can now be hung from the pole clamps. The tabs fit into recesses in the pole clamps. Use the 1/4-20 Phillips screws to secure the brackets to the clamps. Figure 5-5. SkyPilot Pro-Top View - Showing Tabs & Screws Hinge bolts Tab 1/4-20 Phillips-head screws 5 Adjust the angle of the unit, and then tighten the hinge bolts. Mounting | 31 32 |
5 Installing the SkyPilot Gateway Pro Verifying Connectivity After provisioning and installing your SkyPilot devices, you should perform the procedures in the following sections to confirm that the devices are properly connected to the network. 6 Confirming SkyPilot Gateway Pro Connectivity There are two ways to confirm SkyPilot Gateway Pro connectivity:
Check the LED status lights on the SkyPilot Gateway Pro to verify that the device is fully online. See Table 6-1for a summary of what the LED status lights mean. For a detailed description of the status lights, refer to SkyGateway/SkyExtender Installation and Setup. Table 6-1. SkyPilot Gateway Pro LED status lights Device state Link LED Activity LED Startup in progress Slow staggered blinking of both LEDs Startup failure Off On Initializing image (and acquiring GPS signal) Blinks 4 times;
repeats cycle Blinks 4 times;
repeats cycle Initialization failure Fast, synchronized blinking of both LEDs Successful initialization, but authorization failure Connected On On Off On Confirming SkyPilot Gateway Pro Connectivity | 33 From the command line, use the ping command to verify that you can reach the devices default gateway For example:
> ping 192.168.5.1 PING 192.168.5.1: 56 data bytes 64 bytes from 192.168.5.1: icmp_seq=0. time=11. ms 64 bytes from 192.168.5.1: icmp_seq=1. time=12. ms 64 bytes from 192.168.5.1: icmp_seq=2. time=12. ms
----192.168.5.1 PING Statistics----
3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/16/32 34 |
6 Verifying Connectivity Confirming SkyPilot Extender and SkyPilot Connector Connectivity There are four ways to confirm SkyPilot Extender and SkyPilot Connector connectivity. You can use any method at any time. Check the LED status lights on the device to verify that the device is fully online. For a summary of what the LED status lights mean, see Table 6-2 (for SkyPilot Extenders) or Table 6-3 (for SkyPilot Connectors). For a detailed description of the status lights, refer to the installation guide for the device. Table 6-2. SkyPilot Extender/DualBand LED status lights Device state Link LED Activity LED Startup in progress Slow staggered blinking of both LEDs Startup failure Off On Initializing image (and acquiring GPS signal) Blinks 4 times;
repeats cycle Blinks 4 times;
repeats cycle Initialization failure Fast, synchronized blinking of both LEDs Successful initialization, but cant locate hello Successful initialization;
heard hello on antennas with power levels in the proper RSSI range On Off Successful initialization; link is not optimized, or is in pre-authorization Slow blink Off Blink (modulation rate-based) Blink (modulation rate-based) Successful initialization; link is in standby state on antenna and modulation rate Fast blink Blink (modulation rate-based) Connected On On Confirming SkyPilot Extender and SkyPilot Connector Connectivity | 35 Table 6-3. SkyPilot Connector LED status lights LED LED state Device state Lan Link Steady illumination SkyPilot Connector is connected to another device via its Ethernet port LAN Act Blinking Device is transmitting or receiving data via its Ethernet port WAN Link Blinking (fast blink when device is in standby mode) Device is attempting to establish an authorized connection on the wireless network Steady illumination Device is connected to the wireless network WAN Act None Blinking Device cannot detect a wireless network Device is within the coverage area of a wireless network. Blink indicates signal strength:
Fast (8x per second): excellent Medium (4x per second): good Slow (<1x per second): poor From the command line, use the show link command to confirm that an active link exists. The device is online if the output displays an act path (active path) link state. For example:
Node Id LType NType State RSSI LTxMod RTxMod LAnt RAnt
00:0a:db:00:00:43 data ext act path 39 48 36 2 4 Use the traceroute command to confirm that you can send and receive data across the wireless network. The traceroute command performs a SkyPilot protocol trace that shows the path to the SkyPilot Gateway Pro. Entering the traceroute command 36 |
6 Verifying Connectivity without arguments returns a path that the device identifies as its exit from the network. For example:
> traceroute traceroute to 00:0a:db:00:00:a6
>> 1 (48) --> 00:00:43 --> (36) 2 (36) --> 00:00:a6 --> (36) Use the ping command to verify that you can reach the devices default gateway. For example:
> ping 192.168.5.1 PING 192.168.5.1: 56 data bytes 64 bytes from 192.168.5.1: icmp_seq=0. time=11. ms 64 bytes from 192.168.5.1: icmp_seq=1. time=12. ms 64 bytes from 192.168.5.1: icmp_seq=2. time=12. ms ----
192.168.5.1 PING Statistics---- 3 packets transmitted, 3 packets received, 0%
packet loss round-trip (ms) min/avg/max = 0/16/32 Confirming SkyPilot Extender DualBand Access Point Connectivity There are four ways to confirm SkyPilot Extender DualBand access point connectivity:
Use the ping command to verify that the access point is up and runningfor example, ping 192.168.0.3. For SkyPilot firmware versions 1.2p3 and later, use the show version ap command to verify the firmware version and, indirectly, that proper heartbeats are being sent from the PePLink Linux access point. From the command line, enable debugging (using the debug on command) and use the set log apwatchdog 3 command to display successful or failed heartbeat updates, reboot notices, factory resets, and so on. Using an 802.11b/g wireless card, connect to the default SSID, a string representation of the SkyPilot Extenders MAC address with the WPA passphrase publicpublic. Confirming SkyPilot Extender DualBand Access Point Connectivity | 37 Once connected, use the ping command to verify that you can reach both the SkyPilot Extender and the access point. For example:
> ping 192.168.0.3 PING 192.168.5.1: 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0. time=11. ms 64 bytes from 192.168.0.3: icmp_seq=1. time=12. ms 64 bytes from 192.168.0.3: icmp_seq=2. time=12. ms ----
192.168.5.1 PING Statistics---- 3 packets transmitted, 3 packets received, 0%
packet loss round-trip (ms) min/avg/max = 0/16/32
> ping 192.168.0.2 PING 192.168.5.1: 56 data bytes 64 bytes from 192.168.0.2: icmp_seq=0. time=11. ms 64 bytes from 192.168.0.2: icmp_seq=1. time=12. ms 64 bytes from 192.168.0.2: icmp_seq=2. time=12. ms ----
192.168.5.1 PING Statistics---- 3 packets transmitted, 3 packets received, 0%
packet loss round-trip (ms) min/avg/max = 0/16/32 38 |
6 Verifying Connectivity Troubleshooting After making an Ethernet or serial connection to the SkyPilot Gateway Pro, you can manage and troubleshoot the device using a wide range of commands available through the command-line interface. For detailed troubleshooting procedures, refer to the Troubleshooting section in SkyPilot Network Administration. There youll find troubleshooting procedures for:
Power-on problems Ethernet connectivity problems IP connectivity problems SkyPilot Gateway Pro Transmission problems Link failure problems Troubleshooting | 39 40 |
6 Verifying Connectivity A Grounding Guidelines This appendix provides some guidelines for properly grounding the SkyPilot Gateway Pro. Proper grounding protects both your SkyPilot device and equipment connected to it. For the surge protection circuitry built into the SkyPilot equipment to be effective, proper grounding of the unit is necessary. This is especially true if youre installing devices on tall structures, or in areas subject to lightning. NOTE The techniques described in this appendix are intended as general guidelines only and do not constitute a comprehensive guide covering all installation scenarios. For maximum protection, contact a qualified installation specialist who is familiar with your operating environments. If lightning is a threat in your area, consider a consultation with a lightning and transient protection specialist. General Grounding Strategy To ensure optimum reliability, properly ground the metal base of the SkyPilot device. The most efficient way to ground the device is to use an 8 GA or larger wire to connect it to a ground point on the mounting structure or tower. The three most common ground points are:
A cold-water pipe. Make sure it is well-connected to earth. The primary grounding point of the AC electrical system of the building. A 10-foot or longer copper-clad ground rod driven into the earth. For a tower with multiple legs, you need one ground rod per leg and a ground wire loop connecting each of the rods; see Figure 12. Grounding Guidelines | 41 Figure 12. Ground wire loop A Making Connections Gas-Tight Regardless of the grounding point you use, make sure the connections are gas-
tightcapable of retaining low resistance and integrity over time and with exposure to the elements. Use of an antioxide compound and proper sealing is essential. For protection against corrosion, wrap all connections with Scotch 130C tape. Checking Cold-Water Pipe Integrity If youre using a cold-water pipe for grounding, verify the integrity of the ground. In some cases, sections of metal cold-water pipes may have been repaired or extended with PVC material. PVC material or a dielectric union will render a cold-
water pipe ground unacceptable for grounding. 42 | Appendix A Grounding Guidelines Measuring Resistance Verify that there is no more than 5 ohms of resistance between any two ground points in the entire system. Also make sure that all ground points on a structure are tied together. For example, if you use a ground rod and a cold-water pipe as grounding points at different locations on the same structure, you must tie them together. A Adding Surge Protection If youre installing a SkyPilot device in an area thats subject to lightning storms, SkyPilot recommends installing a surge protection device (SPD) at both ends of the Ethernet cableone at the SkyPilot device and one at the point of entry to a building or enclosure. SkyPilot offers SPDs with bracket and cabling designed for use with SkyPilot equipment. For more information, visit SkyPilot customer support at www.skypilot.com/support/ to view accessory guides for SkyPilot-branded surge protection solution. (You may also purchase SPDs from third-party vendors.) Grounding Checklist When grounding a SkyPilot device, use the following checklist to confirm that your installation is adequately protected from power surges and lightning. Connect a ground wire from the SkyPilot device to a ground system on the building or tower. Use shielded CAT5 cabling and connect the drain wire of the shield to ground at the SkyPilot device. (Leave the other end of the drain wire unconnected.) Use the proper size down lead to connect a SkyPilot device on a roof or tower to the ground system of indoor equipment. Verify that all points of the ground system are tied together with less than 5 ohms resistance between any two points. Adding Surge Protection | 43 Run the CAT5 cable inside the tower structure, tying the cable to the tower leg at every 4 feet of length. For increased protection, run the CAT5 cable through metallic conduit installed on the tower. Bleed off any static charge by installing a streamer-delaying, static-dissipation array above the SkyPilot device. Install all lightning and surge protection devices in accordance with UL 96A installation requirements for lightning protection systems and the NFPA 780 standard for lightning protection. A 44 | Appendix A Grounding Guidelines Specifications This appendix provides technical specifications for the SkyPilot Gateway Pro
(Table C-1), Table C-1. SkyPilot Gateway Pro Specifications (Page 1 of 3) C Wireless Specifications Frequency bands EIRP 5.1505.450 GHz 5.4505.725 GHz 5.7255.850 GHz 44.5 dBm/28.2W peak, 36 dBm/4W average, 33 dBm/2W average, 30 dBm/1W average, or 36 dBm/4W peak
(EIRP selected for country-specific regulations) Media access Time Division Duplex (TDD) Modulation technique OFDM with adaptive modulation Modulation rates 654 Mbps Throughput Latency Antennas UDP: Up to 20 Mbps TCP: Up to 10.5 Mbps 1012 ms round trip per hop Electronically-steered antenna, 180-degree coverage Channel width 20 MHz Channel resolution 5 MHz frequency control Receive sensitivity
-90 dBm at 6 Mbps modulation Connectivity SkyPilot Gateway Pro connects with:
SkyPilot Extenders, SkyPilot Extender DualBands SkyPilot Connectors. Authentication MD5-based certificates Encryption 128-bit AES on all wireless links Specifications | 49 Table C-1. SkyPilot Gateway Pro Specifications (Page 2 of 3) Product Specifications Connectors Mounting Range LEDs Dimensions Weight RJ-45: Ethernet connection (10/100Base-T) and power
(Power over Ethernet) RJ-45: RS-232 serial for local management Tower, utility pole, building, or other infrastructure, outside pole diameter up to 2.5". Wall mount possible. Up to 10 miles (16 km) Wireless activity, wireless link 17" (43 cm) H x 11.6" (29.5 cm) wide x 5.5 (14 cm) thick 11 pounds (5 kg), basic unit 17 pounds (7.7 kg) with standard mounting hardware Operating temperature
-40 to 131 F (-40 to 55 C) Wind loading Up to 150 mph (240 km/h) Enclosure/humidity NEMA-4X External PoE PSE Power 110230 VAC, 5060 Hz input, 16 watts maximum Certifications FCC Part 15, FCC 47 CFR Part 15, Class B USA; compliance with UL safety standards, CE, C-Tick, IC RSS210 Issue 5 EMI and susceptibility FCC Part 15.107 and 15.109 Warranty Security One-year limited warranty on hardware and software Authentication MD5-based certificates Encryption Filtering AES Based on protocol type, IP port ID, and configurable IP address list Network management Command-line interface Console via RS-232 serial port or SSH NMS Integration SNMP v2c 50 | Appendix C Specifications Table C-1. SkyPilot Gateway Pro Specifications (Page 3 of 3) GUI configuration SkyProvision software and Web interface GUI EMS IP address Firmware SkyPilot EMS software DHCP or static. 192.168.02. default Multiple versions of firmware stored in nonvolatile memory;
updated via FTP Configuration file XML over HTTP QoS (Quality of Service) Prioritization 802.1p-based; based on protocol type, IP address, port ID, and configurable IP address list Traffic shaping Per-device rate limits upstream and downstream Monitoring and MIB support Supported MIBs MIB-II (RFC 1213); EtherLike (RFC 2665); Bridge (RFC 1493);
SkyPilot private MIB Local management RS-232 Serial Console Port Remote management Command-line interface via Telnet, SNMP 2c, Web interface Topology Configurations Mesh, point-to-multipoint, point-to-point Specifications | 51 52 | Appendix C Specifications Pinouts This appendix provides pinouts for connectors and adapters to connect to the Ethernet interface port labeled CPE on the SkyPilot Gateway Pro power supply and the devices serial interface. D RJ-45 Pins Table D-1 lists the RJ-45 pin assignments. Table D-1. RJ-45 Pin Assignments Pin Assignment 1 2 3 4 5 6 7 8 Ethernet Ethernet Ethernet Power Power Ethernet Power Power Pinouts | 53 DB-9 Adapter Table D-2 lists connecting pins between the SkyPilot Gateway Pro CPE port
(RJ-45 connector) and a standard computer DB-9 serial port. Table D-2. RJ-45 Pin Assignments SkyPilot Gateway/Extender Computer serial port CPE port Signal Pin Pin Signal TxD GND RxD 3 4 6 2 5 3 RxD GND TxD The following figures show the connection between the SkyPilot Gateway Pro CPE port and a standard computer DB-9 serial port, the DB-9 pinouts, and the cable-pin correspondence. Figure D-1. RJ-45 to DB-9 physical connectors Figure D-2. DB-9 pins 54 | Appendix D Pinouts If youre using a straight through cable, the connection can be visualized as shown in Figure D-3. Figure D-3. Straight through cabling Although there is no official standard, the connector wire colors typically are as described in Table D-3. Table D-3. Typical RJ-45 DB-9 Wire Colors Color Black Yellow Red RJ-45 pin DB-9 pin 3 6 4 2 3 5 DB-9 Adapter | 55 Regulatory information Federal Communications Commission (FCC) compliance notices This section includes the following FCC statements for the SP-5200-A and related SkyPilot by Trilliant products:
FCC ID: RV7-GWPRO Class A Interference Statement RF Radiation Exposure and Hazard Warning Non-Modification Statement Deployment Statement Class A Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure & Hazard Statement To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Non-Modification Statement Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the SP-5200-A and related SkyPilot by Trilliant products and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Deployment Statement This product is certified for indoor deployment only in the 5150 5250 MHz band. Do not install or use this product outdoors in that frequency band in the United States. Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands The SP-5200-A has been prohibited from operating in the 5600 to 5650 MHz frequency band for the US and Canada in order to comply with the DFS requirements as outlined in the FCC Part 15, Subpart E rules. 27 | Regulatory Information Canadian IC Statements IC: 6028A-GWPRO This device complies with ICES-003 and RSS-210 of Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme aux normes NMB003 et CNR-210 dIndustrie Canada. 1. Lutilisation de ce dispositif est autorise seulement aux conditions suivantes :
2. il ne doit pas produire de brouillage et lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. RF Radiation Exposure & Hazard Statement To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Exposition aux radiations RF & Mention de danger Pour assurer la conformit avec les exigences RSS-102 d'exposition aux RF (Radio Frquences), cet appareil doit tre install dans un endroit ou l'antenne de l'appareil sera situe une distance de plus de 20 cm (8 po) de toutes personnes. Lutilisation d'antennes gain plus lev et les types d'antennes qui ne sont pas couverts en vertu de la certification IC de ce produit n'est pas autorise. Les installateurs de la radio et les utilisateurs du produit final doivent se conformer aux instructions d'installation fournies dans ce manuel. Cet metteur ne doit pas tre co-implant ou exploit en conjonction avec toute autre antenne ou transmetteur. Deployment Statement This product is certified for indoor deployment only in the 5150 5250 MHz band. Do not install or use this product outdoors in that frequency band in Canada. Dclaration de dploiement Ce produit est certifi pour le dploiement l'intrieur tout en rencontrant les limites de cette bande de frquences: 5150 - 5250 MHz. Ne pas installer ou utiliser ce produit l'extrieur au Canada, si cette bande de frquences ne peut ne peut tre rencontre. 29 | Regulatory Information SAFETY INFORMATION Hazard Warning!
High Voltage. This situation or condition can cause injury due to electric shock. Warnung!
Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt angebracht oder in der Dokumentation enthalten sind. Warning!
Read and follow all warning notices and instructions marked on the product or included in the documentation. Warnung!
Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt angebracht oder in der Dokumentation enthalten sind. Warning!
Only use attachments and accessories specified and/or sold by the manufacturer. Warnung!
Verwenden Sie nur Zusatzgerte und Zubehr angegeben und / oder verkauft wurde durch den Hersteller. Warning!
Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped. Warnung!
Das Gert sollte nur von qualifizierten Fachkrften gewartet werden. Eine Wartung ist fllig, wenn das Gert in irgendeiner Weise beschdigt wurde, wie bei beschdigtem Netzkabel oder Netzstecker, falls Flssigkeiten oder Objekte in das Gert gelangen, das Gert Regen oder Feuchtigkeit ausgesetzt wurde, nicht ordnungsgem funktioniert oder fallen gelassen wurde. Warning!
Do not open the chassis. There are no user-serviceable parts inside. Opening the chassis will void the warranty unless performed by an Trilliant service center or licensed facility. Warnung!
ffnen Sie das Gehuse nicht. Keine der Gerteteile knnen vom Benutzer gewartet werden. Durch das ffnen des Gehuses wird die Garantie hinfllig, es sei denn, solche Wartungsarbeiten werden in einem Trilliant-Service-Center oder einem lizenzierten Betrieb vorgenommen. 29 | Regulatory Information
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-06-13 | 5660 ~ 5700 | NII - Unlicensed National Information Infrastructure TX | Class II permissive change or modification of presently authorized equipment |
2 | 2012-08-23 | 5180 ~ 5240 | NII - Unlicensed National Information Infrastructure TX | Original Equipment |
3 | 5735 ~ 5835 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2013-06-13
|
||||
1 2 3 |
2012-08-23
|
|||||
1 2 3 | Applicant's complete, legal business name |
Trilliant Networks, Inc.
|
||||
1 2 3 | FCC Registration Number (FRN) |
0013833140
|
||||
1 2 3 | Physical Address |
401 Harrison Oaks Boulevard
|
||||
1 2 3 |
Cary, North Carolina 27513
|
|||||
1 2 3 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
c******@micomlabs.com
|
||||
1 2 3 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
RV7
|
||||
1 2 3 | Equipment Product Code |
GWPRO
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
D**** T****
|
||||
1 2 3 | Title |
Certification & Compliance Eng.
|
||||
1 2 3 | Telephone Number |
1-450********
|
||||
1 2 3 | Fax Number |
1-450********
|
||||
1 2 3 |
d******@trilliant.com
|
|||||
app s | Technical Contact | |||||
1 2 3 | Firm Name |
Trilliant Networks
|
||||
1 2 3 |
Trilliant Networks, Inc
|
|||||
1 2 3 | Name |
T****** B********
|
||||
1 2 3 | Physical Address |
1100 Island Drive
|
||||
1 2 3 |
Redwood City, California 94065
|
|||||
1 2 3 |
Redwood City, 94065
|
|||||
1 2 3 |
United States
|
|||||
1 2 3 | Telephone Number |
(530)********
|
||||
1 2 3 | Fax Number |
(530)********
|
||||
1 2 3 |
t******@trilliantinc.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | NII - Unlicensed National Information Infrastructure TX | ||||
1 2 3 | DTS - Digital Transmission System | |||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Mesh WAN Backhaul Node | ||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 | Modular Equipment Type | Does not apply | ||||
1 2 3 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 3 | Original Equipment | |||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 | Grant Comments | Output power is conducted. This device operates at 20 MHz BW mode. Outdoor operation is subject to the professional installation instruction requirements as described in the Users Manual. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 3 | Power Output listed is Conducted. The antennas used for this transmitter must be installed to provide a separation distance of at least 165 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. End users and installers must understand and be provided with the outdoor usage prohibition instructions when using the 5150-5250 MHz Band. This Authorization valid only for the mini-PCI cards identified within this Application. | |||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
Micom Labs
|
||||
1 2 3 | Name |
G****** H******
|
||||
1 2 3 | Telephone Number |
925-4********
|
||||
1 2 3 | Fax Number |
925-4********
|
||||
1 2 3 |
g******@micomlabs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15E | CC | 5180 | 5240 | 0.0017 | |||||||||||||||||||||||||||||||||||
1 | 2 | 15E | CC | 5260 | 5320 | 0.0037 | |||||||||||||||||||||||||||||||||||
1 | 3 | 15E | CC | 5500 | 5580 | 0.0006 | |||||||||||||||||||||||||||||||||||
1 | 4 | 15E | 5660 | 5700 | 0.0006 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | CC | 5180.00000000 | 5240.00000000 | 0.0017000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15C | CC | 5735.00000000 | 5835.00000000 | 0.2148000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC