FCC ID: POD-TYT-A5 Analog Transceiver

Getting Familiar is P S

/

I C M USER'S MANUAL USER'S MANUAL USER'S MANUAL USER'S MANUAL Basic operation 1 Scan Function When the radio is allowed to be scanned, which can be set by the software. you can press the PTT key to turn on or turn off the scan. When the scan begins.indicators lights green. the radio will can scan automatically from channel 1 to 16 which is defined as scan added. When there is signal in the scanning channel, it will stop in the channel for talk. Note:

When there is signal in the scanning channel, it will stop in the channel for a talk and after several seconds. Please note that scan is only available when there are two or more than two memory channels and two or more scan added channels 2. Battery Save Function This function can be set by the software. Turn on this function can make the standby time more longer. 3. Scrambler When the radio is allowed the scrambler function. and press the key. TX voice will be sent out with scrambler. other radio only received the signal when its scrambler also turns on. 4 Busy Channel Lock You can turn on/off this function via software. A: if the current channel does not have CTCSS/DCS, When there is signal. TX prohibited when you press PTT. B: If the current channel does not have CTCSS/DCS. when there is signal which does not have CTCSS/DCS. TX prohibited vvhen you press PTT. C: If the current channels does not have CTCSS/DCS. vvhen there is signal which have CTCSS/DCS. the radio will transmit when you press PTT. 5. Wide/Narrow Bandwidth Setting The default is wide band. You can select the wide band (25KHz) or narrow band(12.5KHz) through the menu "Channel Spacing" of the "Channel Edit" in the software. 6 .VOX Speak to the microphone in normal voice to transmit, no need to press PTT switch, turn VOX on//off though the software. A: when VOX is on in your working channel. Speak to the microphone directly, it will transmit automatically. The radio stops transmitting when there is no voice, and waits for receiving. B: when a headset with a microphone is used. When VOX is on, you should VOX again for the radio to identify voice volume. If the microphone is too sensitive. the noise around radio will start transmitting. If the microphone is not sensitive. the radio can not collect your voice. Please Adjust VOX level well to guarantee smooth communications. English/Chinese Voice Prompt Voice prompt The default setting is Chinese voice prompt. and you will know the working condition of the radio with voice prompt. The purpose of TOT is to prevent any radio from talking in one channel for a long time. and to prevent the transceiver from being damaged because of continuous transmission If the transmitting time exceeds the TOT pre-set time. the radio will sound "Du". Power protection function When the radio is in normal use or maintenance, the transmission will be prohibited if the working voltage is beyond the normal supplying voltage. Lower than 3V or higher than 5V, the transmission will be prohibition. The radio cannot power on when it is higher than 5V. CTCSS/DCS CTCSS and DCS is the sub-audio signaling, to prevent the radio from receiving unwanted signal in the same channel. When the CTCSS/DCS is set, then within the communication range, you can only receive signals from the same channel with the same CTCSS/DCS setting. When the CTCSS/DCS is not set, you will get all the signal from the same channel within the communication range. 1 ) The voice prompt can be selected "Chinese/English/Tone/OFF" through the menu

"Voice/Beep Tone" of the "Optional Features" in the software for. When choosing

"OFF", voice prompt turns off. 2) Channel annunciation: You will get to know the working conditions of current channel which is being operated. 3) Low battery alert: The radio will alert you when the battery capacity reaches the minimum operating voltage. Low battery prompt The default setting is Chinese voice prompt. When transmitting or standby. if the battery capacity reaches the pre-determined low level. the indicator light blinks red. and a low battery alert tone will be heard. The indicating tone can be "Please change the battery". When the low battery alert occurs. it can not transmit. please change or charge the battery. Squelch function The squelch level will determine the signal strength to open the speaker of the radio. If the squelch level is lower. the background noise of opening the radios speaker will be higher. and the corresponding communication range will be further. but the anti-interference capacity will be weaker. The default setting of squelch level is 5. you can adjust it through the menu -Squelch Level"

of the -Optional Features- in the software for. Level 0 to 9 can be selected. 0 is the lowest level. Time out timer (TOT) TX: 420-450MHz RX: 400-470MHz 2.5 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBIITED UNDER FCC RULES AND FEDERRAL LAW.

Internal Photos OPEN VIEW-1 OF EUT OPEN VIEW-2 OF EUT OPEN VIEW-3 OF EUT INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT INTERNAL VIEW-6 OF EUT

External Photos TOTAL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCC ID Label Location FCC ID: POD-TYT-A5 WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Block 39-1,Optoelectronics-information industry base,Nanan,Quanzhou,Fujian,China TYT ELECTRONICS CO., LTD 2017-07-08 To:

Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation statement regarding the Land Mobile Radio frequency Applicant: TYT ELECTRONICS CO., LTD TYPE OF QEUIPMENT: Scanning Receiver FCC ID: PODTYT-A5 Dear Sir or Madam I attest that that the product meets the requirement of FCC15.121. I attest that the receiver is incapable of tuning, or readily being altered, by the user to operate bands allocated to the scanning receiver in FCC15.121. The firmware of scanner receiver can discriminate the receiver and transmission, the frequency range will be limited to 400-480MHZ for receiver, and 420-450 MHZ for transmission. I attest that the receiver is designed so that the tuning, control and filtering circuitry is inaccessible. The original circuit design only for scanner receiver purpose, it is useless even they tuning, control and filtering circuitry. I attest that the scanner receiver have the high/low pass and band-pass filer design to reject any signals from the Cellular Radiotelephone Service frequency bands that are 38dB or lower I attest that any modification of a scanning receiver to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to a scanning receiver to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. Please contact the undersigned if you have any questions or need any further information. Regards Signature:

Name, Job Title and Dept: Jiamao Lin/Manager

Block 39-1, Optoelectronics-information industry base, Nanan, Quanzhou, Fujian, China TYT ELECTRONICS CO., LTD Date: 23 October 2018 PHOENIX TESTLAB GmbH Product Certification Knigswinkel 10 D 32825 Blomberg FCC ID: POD-TYT-A5 Subject: Declaration of compliance to the requirements of 15.121 We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semiconductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver inoperable. This scanning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. If you have any questions, please feel free to contact me. Thank you. Sincerely, Signatory

[Jiamao Lin, Manager]

TY? ELECTRONICS CO... 1TD Block 39-1, Optoelectronics-information industry base, Nanan, Quanzhou, Fujian, China Sep. 13, 2018 Federal Communication Commission Authorization and Evaluation Division FCC ID: POD-TYT-A5 Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the*Commissions Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below:

1: Block Diagram 2: Schematics 3: Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and |

all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, TYT ELECTRONICS CO.,.LTD Contact person: Jiamao Lin Title: Monader [ilk mad ban