FCC ID: XPYEMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1

 

EMMY-W1 series Host-based multiradio modules with Wi-Fi, Bluetooth and NFC Data Sheet Abstract This technical data sheet describes the EMMY-W1 series modules with Wi-Fi 802.11ac, Bluetooth v4.2 (Bluetooth Smart Ready) and Near-Field Communication (NFC) designed for both simultaneous and independent operation. These modules include an integrated MAC/baseband processor and RF front-end components and can connect to a host processor through SDIO 3.0 or high-speed UART interfaces. A PCM interface is available for Bluetooth audio applications. These modules are offered in both professional and automotive grades. www.u-blox.com UBX-15011785 - R05 EMMY-W1 series - Data Sheet Document Information Title Subtitle EMMY-W1 series Host-based multiradio modules with Wi-Fi, Bluetooth and NFC Document type Data Sheet Document number UBX-15011785 Revision and date R05 15-Dec-2016 Disclosure restriction Product Status Corresponding content status Functional Sample Draft For functional testing. Revised and supplementary data will be published later. In Development /

Prototype Objective Specification Target values. Revised and supplementary data will be published later. Engineering Sample Advance Information Data based on early testing. Revised and supplementary data will be published later. Initial Production Early Prod. Information Data from product verification. Revised and supplementary data may be published later. Mass Production /

End of Life Production Information Final product specification. This document applies to the following products:

Product name Type number Firmware version PCN reference Product Status EMMY-W161 EMMY-W161-00B-00 EMMY-W161-00B EMMY-W161-A EMMY-W161-00A-00 EMMY-W161-00A N/A N/A Initial Production Initial Production EMMY-W163 EMMY-W163-00B-00 EMMY-W163-00B UBX-16017374 Initial Production EMMY-W163-A EMMY-W163-00A-00 EMMY-W163-00A UBX-16017374 Initial Production EMMY-W165 EMMY-W165-00B-00 EMMY-W165-00B EMMY-W165-A EMMY-W165-00A-00 EMMY-W165-00A N/A N/A Initial Production Initial Production u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or any part thereof without the express permission of u-blox is strictly prohibited. The information contained herein is provided as is and u-blox assumes no liability for the use of the information. No warranty, either express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose of the information. This document may be revised by u-blox at any time. For most recent documents, visit www.u-blox.com. Copyright 2017, u-blox AG. u-blox is a registered trademark of u-blox Holding AG in the EU and other countries. ARM is the registered trademark of ARM Limited in the EU and other countries. UBX-15011785 - R05 Page 2 of 47 EMMY-W1 series - Data Sheet Contents Contents .............................................................................................................................. 3 1 Functional description .................................................................................................. 5 1.1 Overview .............................................................................................................................................. 5 Applications .......................................................................................................................................... 5 1.2 Product features ................................................................................................................................... 6 1.3 1.4 Block diagrams ..................................................................................................................................... 6 Product description ............................................................................................................................... 7 1.5 Supported features ............................................................................................................................... 8 1.6 1.6.1 Wi-Fi features ................................................................................................................................ 8 1.6.2 Bluetooth features ......................................................................................................................... 8 NFC features ................................................................................................................................. 8 1.6.3 General product features ............................................................................................................... 8 1.6.4 1.6.5 Compliance ................................................................................................................................... 9 Additional reserved MAC addresses ...................................................................................................... 9 1.7 2 2.2.1 2.2.2 2.2.3 2.2.4 Interfaces .................................................................................................................... 10 2.1 Operation mode configuration ........................................................................................................... 10 SDIO interface .................................................................................................................................... 10 2.2 Default speed and High speed modes ......................................................................................... 10 SDR12, SDR25, SDR50 Modes (up to 100 MHz) (1.8 V) ............................................................... 11 SDR104 Mode (208 MHz) (1.8 V) ................................................................................................ 12 DDR50 Mode (50 MHz) (1.8 V) .................................................................................................... 13 High Speed UART interface ................................................................................................................. 14 PCM interface ..................................................................................................................................... 15 PCM interface specifications ........................................................................................................ 15 2.5 GPIO interface .................................................................................................................................... 16 2.3 2.4 2.4.1 3 Pin Definition .............................................................................................................. 18 Pin description .................................................................................................................................... 18 Reset configuration............................................................................................................................. 20 3.1 3.2 4 Electrical specification ................................................................................................ 21 4.1 Absolute maximum ratings ................................................................................................................. 21 4.2 Operating conditions .......................................................................................................................... 21 4.3 Digital pin ratings ............................................................................................................................... 22 4.4 Wi-Fi power consumption ................................................................................................................... 22 Bluetooth power consumption ........................................................................................................... 23 4.5 4.6 NFC power consumption .................................................................................................................... 23 Radio specifications ............................................................................................................................ 24 4.7 4.7.1 Wi-Fi ........................................................................................................................................... 24 Bluetooth .................................................................................................................................... 25 4.7.2 4.7.3 LTE co-existence .......................................................................................................................... 25 Near field communication ........................................................................................................... 26 4.7.4 UBX-15011785 - R05 Contents Page 3 of 47 EMMY-W1 series - Data Sheet 5 Host drivers and firmware ......................................................................................... 27 5.1 General principle ................................................................................................................................ 27 5.2 Supported operating systems .............................................................................................................. 27 Linux ........................................................................................................................................... 27 5.2.1 6 Mechanical specifications .......................................................................................... 28 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.1.5 7.1.6 7 Qualification and approvals ...................................................................................... 30 Approvals ........................................................................................................................................... 30 European Union regulatory compliance ....................................................................................... 30 FCC compliance .......................................................................................................................... 31 IC compliance.............................................................................................................................. 32 Australia and New Zealand regulatory compliance ....................................................................... 33 Korean KCC compliance .............................................................................................................. 33 Japan radio equipment compliance ............................................................................................. 33 Approved antennas ............................................................................................................................ 34 Bluetooth antenna ...................................................................................................................... 34 NFC antenna ............................................................................................................................... 34 FCC and IC IDs ................................................................................................................................... 35 Korea KCC IDs .................................................................................................................................... 35 Japan Giteki IDs .................................................................................................................................. 35 Bluetooth qualification ....................................................................................................................... 35 Bluetooth host stack .................................................................................................................... 35 7.3 7.4 7.5 7.6 7.2.1 7.2.2 7.6.1 7.2 8.1 8.1.1 8.1.2 8 Product handling ........................................................................................................ 36 Packaging ........................................................................................................................................... 36 Reels ........................................................................................................................................... 36 Tapes .......................................................................................................................................... 36 Shipment, storage and handling ......................................................................................................... 37 8.2.1 Moisture sensitivity levels ............................................................................................................. 37 8.2.2 Mounting process and soldering recommendations ..................................................................... 37 ESD handling precautions ............................................................................................................ 38 8.2.3 8.2 9 Labeling and ordering information ........................................................................... 40 Product labeling .................................................................................................................................. 40 9.1 9.2 Explanation of codes........................................................................................................................... 41 9.3 Ordering codes ................................................................................................................................... 42 Appendix .......................................................................................................................... 43 A Glossary ...................................................................................................................... 43 Related documents........................................................................................................... 45 Revision history ................................................................................................................ 46 Contact .............................................................................................................................. 47 UBX-15011785 - R05 Contents Page 4 of 47 EMMY-W1 series - Data Sheet 1 Functional description 1.1 Overview The EMMY-W1 series provides a complete short range transceiver solution that can easily be integrated into automotive and industrial applications. The modules are designed for both simultaneous and independent operation of the following technologies:

IEEE 802.11a/b/g/n/ac data rates for Wi-Fi Dual-mode Bluetooth v4.2 NFC The EMMY-W1 series is a surface-mount device (SMD) component and can be used as a Wi-Fi micro-access point supporting up to 10 clients. A coexistence feature at the chip level improves parallel use of Bluetooth and Wi-Fi communication. For highest throughput and performance, a module variant with separate Wi-Fi and Bluetooth antenna pins is also available. The modules include an integrated MAC/baseband processor and RF front-end components and can connect to a host processor through SDIO 3.0 and high-speed UART interfaces. The EMMY-W1 series are offered in automotive and professional grades (see Ordering codes and Block diagrams). The automotive grade variant includes an automotive-qualified (AEC-Q100) chipset. A host driver for Linux 3.x is available free of charge. The modules are radio type approved for Europe (ETSI R&TTE), US (FCC CFR 47 part 15 unlicensed modular transmitter approval), Canada (IC RSS), Korea (KCC)1, Japan (MIC)1 and Australia / New Zealand (ACMA)2. Approvals for other countries may be possible upon inquiry. 1.2 Applications Automotive applications High definition (HD) video streaming (headrest displays, rear-view camera) and in-car gaming Rapid sync-n-go applications and fast content download to the vehicle Hands-free equipment (Bluetooth) Personalized adjustment of comfort functions through NFC Industrial applications Manufacturing floor automation, wireless control terminals and point-to-point backhaul Outdoor content distribution Mobile video streaming Robust wireless connectivity in a broad range of industrial applications 1 EMMY-W163 and EMMY-W163-A only 2 EMMY-W161 and EMMY-W161-A only UBX-15011785 - R05 Functional description Page 5 of 47 EMMY-W1 series - Data Sheet 1.3 Product features Model Radio Interfaces Power Connectors Features Grade 3 1

-

1 s l e n n a h c z H G 4

. 2 i F

-

i W 5 6 1

-

6 3 s l e n n a h c z H G 5 i F

-

i W i n p a n n e t n a t a r e w o p t u p t u o x a M n o i s r e v 1 1

. 2 0 8 E E E I i F

-

i W n o i t a c i f i l a u q h t o o t e u B l s e l i f o r p h t o o t e u B l C F N T R A U d e e p s

-

h g H i 0

. 3 O D S I r e t l i f E T L e p y t a n n e t n A i

) o d u a h t o o t e u B

(

l M C P EMMY-W161 a/b/g/n/ac v4.2 H 18 dBm 1p EMMY-W163 a/b/g/n/ac v4.2 H 18 dBm 2p EMMY-W165 a/b/g/n/ac v4.2 H 18 dBm 1p V 6

. 3

-

0

. 3

:

y l p p u s r e w o P y r o m e m P T O n i s r e t e m a r a p F R y r o m e m P T O n i s e s s e r d d a C A M t r o p p u s e r a w d r a h S E A i t n o P s s e c c A o r c i M l a n o i s s e f o r P e v i t o m o t u A d r a d n a t S i s n p r e d o S l H = HCI 1p = One pin for combined external antenna for Bluetooth and Wi-Fi Table 1: EMMY-W1 series main features summary 2p = Two pins for separate external antennas for Bluetooth and Wi-Fi 1.4 Block diagrams The block diagrams of the EMMY-W1 series are provided in this section. Figure 1: EMMY-W161/EMMY-W165 block diagram - Single antenna variant UBX-15011785 - R05 Functional description Page 6 of 47 MAC/BB/RADIO2.4GHz WLAN TX2.4GHz WLAN/BT RXBT TXWLAN &BT ANT5GHz WLAN TX/RX5GHz BPF &DIPLEXER2.4GHzBPFEMMY-W161 / EMMY-W165SDIO37.4 MHzCrystalVIO1UARTVIO2PCMVIO2BT LTE COEXVIO2BT LEDWLAN LEDPDnSP3T3.3VVIO1VIO2GNDNFCCOILVIO2GPIOsDC/DC3.3V1.8V1.1V EMMY-W1 series - Data Sheet In EMMY-W161, the band pass filter (2.4 GHz BPF) is a BAW filter that enables co-existence with LTE. For the EMMY-W165 variant, the band pass filter provides no co-existence protection against a co-located LTE transmitter. Figure 2: EMMY-W163 block diagram - Dual-antenna variant In EMMY-W163, the bandpass filters (2.4 GHz BPF) are ceramic bandpass filters. An LTE co-existence variant is not available in the dual-antenna configuration. 1.5 Product description Model Description EMMY-W161 EMMY-W163 EMMY-W165 Professional grade module with 1 combined antenna pin for Wi-Fi and Bluetooth and integrated LTE filter Professional grade module with 2 separate antenna pins for Wi-Fi and Bluetooth (no LTE filter) Professional grade module with 1 combined antenna pin for Wi-Fi and Bluetooth (no LTE filter) EMMY-W161-A Automotive grade module with 1 combined antenna pin for Wi-Fi and Bluetooth and integrated LTE filter EMMY-W163-A Automotive grade module with 2 separate antenna pins for Wi-Fi and Bluetooth (no LTE filter) EMMY-W165-A Automotive grade module with 1 combined antenna pin for Wi-Fi and Bluetooth (no LTE filter) The EMMY-W161 is recommended for applications that have co-located Wi-Fi, Bluetooth and LTE antennas and require co-existence of these wireless technologies. This module provides a dedicated BAW bandpass filter instead of the ceramic bandpass filter. This filter rejects the adjacent LTE bands B40, B7, B41 and B38. The integrated BAW filter is available only for the single-antenna configuration (EMMY-W161). The module pinout, operating conditions, and electrical characteristics are identical for all product variants. Differences in the RF parameters are explained in the Radio specifications section. UBX-15011785 - R05 Functional description Page 7 of 47 MAC/BB/RADIO2.4GHz WLAN TX2.4GHz WLAN RXBT RX/TXWLANANT5GHz WLAN TX/RX5GHz BPF &DIPLEXER2.4GHzBPFEMMY-W163SDIO37.4 MHzCrystalVIO1UARTVIO2PCMVIO2BT LTE COEXVIO2BT LEDWLAN LEDPDn2.4GHzBPFSP3T3.3VVIO1VIO2GNDNFCCOILBTANTVIO2GPIOsDC/DC3.3V1.8V1.1V EMMY-W1 series - Data Sheet 1.6 Supported features 1.6.1 Wi-Fi features Simultaneous client and access point operation (up to 10 clients supported) Support of Wi-Fi direct mode IEEE 802.11ac 1x1 antenna configuration IEEE 802.11 PHY data rates up to 433 Mbps Wi-Fi standards: IEEE 802.11a/b/g/n/ac/d/e/h/i/k3/r/v3/w 64- and 128-bit AES hardware encryption engine WAPI encryption is supported by hardware SDIO 3.0 host interface for Wi-Fi 1.6.2 Bluetooth features Bluetooth v4.2 with Bluetooth Low Energy and Classic Bluetooth v2.1+EDR over SDIO or high-speed UART interface PCM interface for audio MWS/LTE coexistence serial transport interface for connecting an external and co-located LTE device4 1.6.3 NFC features NCI 1.0 support according to NFC Forum specification NFC support through SDIO or UART Full protocol support for ISO 14443A/B, ISO 156935, ISO 18092, NFCIP-2, NFC forum, EMV contactless targets with data rates up to 848 Kbps Proprietary Low-Power Target Detection mode to reduce standby current consumption Deep Sleep On-Host card emulation: supported in NFC A, B, F and V technologies Off-Host card emulation with UICCs and Embedded SEs (availability is package dependent):

o ETSI TS 102 613: SWP/CLT ISO14443 Type A (Mifare) and ISO18093 212/424 kbps passive mode (FeliCa). o ETSI TS 102 622: SWP/HCI ISO14443A/B and ISO18092 212/424 kbps passive mode o DCLB Compliant with EMVCo book D (Contactless Communication Protocol) Reader/Writer, card emulation, and Peer-to-peer (P2P) modes Programmable carrier detection level for card emulation mode Programmable field detection level for RF anti-collision when operating as reader or active target UART host interface support (shared with Bluetooth when operating) 1.6.4 General product features Low-power and sleep modes for Bluetooth and Wi-Fi core Driver support for Linux Coexistence arbitration for Wi-Fi/Bluetooth/LE/NFC/LTE operation Automotive qualification tests (climatic, mechanical, and operating life tests) according ISO 16750-4 Small footprint (19.8 mm x 13.8 mm), LGA package Product variant with integrated LTE co-location filter available planned 3 Supported by hardware but not supported by firmware currently. 4 Available on request 5 For ISO 15693 VICC mode, the maximum supported 10-90% rise/fall times for receiving 10% ASK modulation is 1.18 s. UBX-15011785 - R05 Functional description Page 8 of 47 EMMY-W1 series - Data Sheet 1.6.5 Compliance RoHS compliant Radio type approvals for Europe, USA, Canada, Korea, Japan, Australia, and New Zealand. 1.7 Additional reserved MAC addresses The EMMY-W1 module series has four unique consecutive MAC addresses reserved for each module, from which the first two addresses are already stored in the configuration during production. The first address is used for the Bluetooth communication while the second address is configured for Wi-Fi communication. The Data Matrix Code on the label includes the Bluetooth MAC address (see section 9). The remaining two MAC addresses are not used in the manufacturing configuration, but are reserved for usage with the module. MAC address Module1, address 1 Module1, address 2 Module1, address 3 Module1, address 4 Module2, address 1 Module2, address 2 Module2, address 3 Module2, address 4 Assignment Bluetooth Wi-Fi

(free for use)

(free for use) Bluetooth Wi-Fi

(free for use)

(free for use) Table 2: MAC address assignment Last two bits of MAC address Example 0b00 0b01 0b10 0b11 0b00 0b01 0b10 0b11 D4:CA:6E:44:00:04 D4:CA:6E:44:00:05 D4:CA:6E:44:00:06 D4:CA:6E:44:00:07 D4:CA:6E:44:00:08 D4:CA:6E:44:00:09 D4:CA:6E:44:00:0A D4:CA:6E:44:00:0B UBX-15011785 - R05 Functional description Page 9 of 47 EMMY-W1 series - Data Sheet 2 Interfaces 2.1 Operation mode configuration EMMY-W1 series module uses the GPIO_3 and GPIO_2 pins as host interface configuration input to set the desired operation mode following a reset. The definitions of these pins are changed to their usual functions after reset. When you need to configure the pins for a certain module operation mode, you need to provide a 100 k pull down resistor to the ground. No external circuitry is required to set a configuration pin to high logical level. External reset is not needed for proper operation due to internal power-up reset logic though it can be used by the host controller through the PDn pin (active low) in case of an abnormal module behavior. After reset, GPIO_3 and GPIO_2 pins can be used as open drain outputs (depending on firmware/driver version) for Bluetooth and Wi-Fi activity LED indicators, but simultaneous usage of an LED connected to 3.3 V power line and a pull-down resistor is not allowed (LED acts as a strong pull-up circuitry). Do not connect LED if you need the pull-down resistors. Depending on the firmware or driver used, you can use either one or both host interface operation modes:

GPIO_3 GPIO_2 0 0 1 1 0 1 0 1 Wi-Fi SDIO SDIO SDIO SDIO Bluetooth/NFC Number of SDIO functions UART SDIO UART SDIO 1 (Wi-Fi) 3 (Wi-Fi, Bluetooth and NFC) 1 (Wi-Fi) 3 (Wi-Fi, Bluetooth and NFC)6 Table 3: Module configuration 2.2 SDIO interface EMMY-W1 series modules support an SDIO device interface that conforms to the industry standard SDIO 3.0 Full-Speed specification (4-bit SDIO up to 208 MHz) and allows a host controller using the SDIO bus protocol to access the Wi-Fi and Bluetooth functions. The interface supports 4-bit SDIO transfer mode at the full clock range of 0 to 208 MHz. 2.2.1 Default speed and High speed modes Figure 3: SDIO protocol timing diagram- Default speed mode (3.3 V) 6 Default configuration. It is possible to use connected LEDs to both the pins. UBX-15011785 - R05 Interfaces Page 10 of 47 EMMY-W1 series - Data Sheet Figure 4: SDIO protocol timing diagram High speed mode (3.3 V) Symbol Parameter fPP TWL TWH TISU TIH TODLY(max) TODLY(min) TODLY Clock frequency Clock low time Clock high time Input setup time Input hold time Maximal Output delay time Minimal Output delay time Output delay time CL 40 pF

(1 card) Condition Normal High speed Normal High speed Normal High speed Normal High speed Normal High speed Normal Normal Normal 0 0 10 7 10 7 5 6 5 2 TOH Output hold time High speed 2.5 Table 4: SDIO timing data Default speed, High speed modes (3.3 V) Min. Typ Max.

-

-

-

-

-

-

-

-

-

-

-

-

-

-

25 50

-

-

-

-

-

-

-

-

14 0 14

-

2.2.2 SDR12, SDR25, SDR50 Modes (up to 100 MHz) (1.8 V) Units MHz MHz ns ns ns ns ns ns ns ns ns ns ns ns Figure 5: SDIO protocol timing diagram SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8 V) UBX-15011785 - R05 Interfaces Page 11 of 47 Symbol Parameter Min. Typ fPP TIS TIH TCLK TCR, TCF, TODLY TOH Clock frequency Input setup time Input hold time Clock time Rise time, fall time TCR, TCF < 2 ns (max) at 100 MHz CCARD = 10 pF Output delay time CL 30 pF Output hold time CL = 15 pF Condition SDR12/25/50 SDR12/25/50 SDR12/25/50 SDR12/25/50 SDR12/25/50 SDR12/25/50 25 3 0.8 10 SDR12/25/50 1.5 EMMY-W1 series - Data Sheet Max. 100

-

-

40 0.2*TCLK 7.5

-

Units MHz ns ns ns ns ns ns

-

-

-

-

-

-

-

Table 5: SDIO timing data SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8 V) 2.2.3 SDR104 Mode (208 MHz) (1.8 V) Figure 6: SDIO protocol timing diagram SDR104 mode (208 MHz) Symbol Parameter Condition Min. Typ fPP TIS TIH TCLK TCR, TCF, TOP TODW Clock frequency Input setup time Input hold time Clock time Rise time, fall time TCR, TCF < 0.96 ns (max) at 208 MHz CCARD = 10 pF Card output phase SDR104 SDR104 SDR104 SDR104 SDR104 SDR104 Output timing of variable data window SDR104 Table 6: SDIO timing data SDR104 mode (208 MHz) 0 1.4 0.8 4.8 0 2.88

-

-

-

-

-

-

-

Units MHz ns ns ns ns ns ns Max. 208

-

-

-

0.2*TCLK 10

-

UBX-15011785 - R05 Interfaces Page 12 of 47 2.2.4 DDR50 Mode (50 MHz) (1.8 V) EMMY-W1 series - Data Sheet Figure 7: SDIO CMD timing diagram DDR50 mode (50 MHz) Figure 8: SDIO DAT[3:0] timing diagram DDR50 mode (50 MHz) UBX-15011785 - R05 Interfaces Page 13 of 47 EMMY-W1 series - Data Sheet Symbol Parameter Condition Min. Typ Max. Units Clock TCLK TCR, TCF, Clock time 50 MHz (max) between rising edges Rise time, fall time TCR, TCF < 4.00 ns (max) at 50 MHz CCARD = 10 pF Clock Duty CMD Input (referenced to clock rising edge) TIS TIH Input setup time CCARD 10 pF (1 card) Input hold time CCARD 10 pF (1 card) DDR50 DDR50 DDR50 DDR50 20 45 6 DDR50 0.8 CMD Output (referenced to clock rising edge) TODLY TOHLD Output delay time during data transfer mode CL 30 pF (1 card) DDR50 Output hold time CL 15 pF (1 card) DDR50 1.5 DAT[3:0] Input (referenced to clock rising and falling edges) TIS2x TIH2x Input setup time CCARD 10 pF (1 card) Input hold time CCARD 10 pF (1 card) DDR50 3 DDR50 0.8 DAT[3:0] Output (referenced to clock rising and falling edges) TODLY2x (max) TODLY2x (min) Output delay time during data transfer mode CL 25 pF (1 card) DDR50 Output hold time CL 15 pF (1 card) DDR50 1.5 Table 7: SDIO timing data DDR50 mode (50 MHz) 2.3 High Speed UART interface 0.2*TCLK 55 13.7 7.0 ns ns

%

ns ns ns ns ns ns ns ns The EMMY-W1 series modules support a high speed Universal Asynchronous Receiver/Transmitter (UART) interface in compliance with the industry standard 16550 specification. The main features of the UART interface are:

FIFO mode permanently selected for transmit and receive operations 2 pins for transmit and receive operations 2 flow control pins High throughput (4 Mbps) Interrupt triggers for low-power, high throughput operation The UART interface operation includes:

Uploading the firmware to the module Supporting data input/output operation for peripheral devices connected through a standard UART interface Baud Rate 1200 2400 4800 9600 19200 38400 57600 76800 115200 230400 Table 8: Supported UART Baud rates UBX-15011785 - R05 460800 500000 921600 1000000 1382400 1500000 1843200 2000000 2100000 2764800 3000000 3250000 3692300 4000000 Interfaces Page 14 of 47 2.4 PCM interface The EMMY-W1 series modules support a Pulse Code Modulation (PCM) interface that provides:

EMMY-W1 series - Data Sheet PCM bit width size of 8 bits or 16 bits Master or slave mode Up to 4 slots with configurable bit width and start positions Short frame and long frame synchronization 2.4.1 PCM interface specifications Figure 9: PCM timing specification Master mode Symbol FBCLK Duty Cycle BCLK TBCLK rise/fall TDO TDISU TDIHO TBF Parameter Condition Min. Typ Max.

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

0.4

-

-

20 15

-

2/2.048 0.5 3

-

-

-

-

-

0.6

-

15

-

-

15 Units MHz

-

Ns ns ns ns ns Table 9: PCM timing specification Master mode UBX-15011785 - R05 Interfaces Page 15 of 47 EMMY-W1 series - Data Sheet Figure 10: PCM timing specification Slave mode Symbol FBCLK Duty Cycle BCLK TBCLK rise/fall TDO TDISU TDIHO TBFSU TBFHO Parameter Condition Min. Typ Max.

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

0.4

-

-

15 10 15 10 2/2.048 0.5 3

-

-

-

-

-

-

0.6

-

30

-

-

-

-

Units MHz

-

ns ns ns ns ns ns Table 10: PCM timing specification Slave mode 2.5 GPIO interface The General-Purpose I/O (GPIO) interface is used to implement user defined input and output signals to and from the 88W8887 chip such as external interrupts and other user-defined I/Os. Main features of the GPIO interface include:

User-defined GPIO (each I/O configured to either input or output) Each GPIO independently controlled Each I/O configurable to output bit from GPIO_OUT The general functions associated with each GPIO pin is shown in Table 11:

UBX-15011785 - R05 Interfaces Page 16 of 47 EMMY-W1 series - Data Sheet GPIO Function General Input Output LEDs7 LED output8 Interrupts Input GPIO Pin 0 X X

-

X 1 X X

-

X 2 X X X X 3 X X X X 4 X X

-

X 5 X X

-

X 6 X X

-

X 7 X X

-

X 8 X X

-

X 9 X X

-

X 10 11 14 15 16 17 X X

-

X X X

-

X X X

-

X X X

-

X X X

-

X X X

-

X Table 11: GPIO Functions GPIO [17:14], [11:0]

GPIO_12 and GPIO_13 are not available. 7 The possibility to use as an LED output depends on the firmware and driver version. 8 GPIO [2] is used for Wi-Fi activity while GPIO [3] is used for Bluetooth activity. UBX-15011785 - R05 Interfaces Page 17 of 47 EMMY-W1 series - Data Sheet 3 Pin Definition 3.1 Pin description Figure 11: EMMY-W1 series pin assignment (top view) No Pin name Pin type Supply domain Description 1 2 3 4 5 6 7 8 9 GND NC NC NC GPIO_0 GPIO_1 GPIO_14 GPIO_15 GPIO_16 10 GPIO_17 11 GPIO_4 Ground I/O I/O I/O I/O I/O I/O I/O

-

-

-

-

VIO2 VIO2 VIO2 VIO2 VIO2 VIO2 VIO2 Ground Reserved, do not connect Reserved, do not connect Reserved, do not connect BT2HOST_WAKEUP (Output) WL2HOST_WAKEUP (Output) HOST2WL_WAKEUP (Input) HOST2BT_WAKEUP (Input) UART_LTE_SIN (Input) UART_LTE_SOUT (Output) PCM_DIN (Input) UBX-15011785 - R05 Pin Definition Page 18 of 47 EMMY-W1 series - Data Sheet No Pin name Pin type Supply domain Description 12 GPIO_5 13 GPIO_6 14 GPIO_7 15 GND 16 GND 17 18 19 20 21 22 SD_CLK SD_CMD SD_D0 SD_D1 SD_D2 SD_D3 23 GND 24 GND 25 26 27 28 3V3 VIO1 VIO2 PDn 29 GPIO_8 30 GPIO_9 31 GPIO_10 32 GPIO_11 33 GPIO_3 34 GPIO_2 I/O I/O I/O Ground Ground I I/O I/O I/O I/O I/O Ground Ground Power Power Power Input I/O I/O I/O I/O I/O I/O VIO2 VIO2 VIO2

-

-

VIO1 VIO1 VIO1 VIO1 VIO1 VIO1

-

-

3.3V VIO1 VIO2

-

VIO2 VIO2 VIO2 VIO2 3.3V 3.3V PCM_DOUT (Output) PCM_CLK (Input if slave, Output if master) PCM_SYNC (Input if slave, Output if master) Ground Ground SDIO Clock input SDIO Command line SDIO Data line bit [0]

SDIO Data line bit [1]

SDIO Data line bit [2]

SDIO Data line bit [3]

Ground Ground 3.3V Power supply (2.97 V - 3.63 V) VIO1 Power supply (1.62V - 1.98 V, 2.97 V - 3.63 V) VIO2 Power supply (1.62V - 1.98 V, 2.97 V - 3.63 V) Full power down(active low)9 UART_SOUT (Output) UART_SIN (Input) UART_CTSn (Input) UART_RTSn (Output) LED_OUT_BT (Output) - BT indicator, Configuration pin10, PCM_MCLK (output if master, input if slave) LED_OUT_WLAN (Output) - WLAN indicator, Configuration pin10 35 GND Ground

-

Ground 36 37 NFC_ANT_N I/O, RF NFC_ANT_P I/O, RF 3.3V 3.3V NFC Coil Antenna, negative I/O pin NFC Coil Antenna, positive I/O pin 38 GND 39 GND 40 ANT2 41 GND 42 GND 43 GND 44 GND 45 ANT1 Ground Ground I/O, RF Ground Ground Ground Ground I/O, RF 46 GND Ground

-

Exposed pin Ground

-

-

-

-

-

-

-

-

-

-

Table 12: EMMY-W1 series pin description Ground Ground Bluetooth antenna only in case of EMMY-W163 module. Not connected in case of EMMY-W161 or EMMY-W165 module11 Ground Ground Ground Ground Wi-Fi + Bluetooth antenna in case of single-antenna module. Wi-Fi antenna only in case of dual-antenna module11 Ground Six Ground/Thermal exposed pins, connect to the ground 9 High input impedance pin for minimizing shutdown current consumption. The pin shall be driven by the host controller or/and connected via 51 k (or less) pull-up resistor to the 3.3 V supply rail. 10 Possible to use as an LED output depending on the firmware and driver version. In this case, the module pin acts as an open drain output and the whole LED circuitry must be supplied from 3.3 V power line. A LED current limiting resistor should be used; maximum sink current to the ground is 10 mA. These pins can also be used for host interface configuration. See Operation mode configuration section. 11 Pin protected from the static electricity by internal DC feed to the ground. UBX-15011785 - R05 Pin Definition Page 19 of 47 EMMY-W1 series - Data Sheet 3.2 Reset configuration The EMMY-W1 is reset to its default operating state under the following conditions:

Power-on reset (POR) Module receives power 3V3 supplies rise (triggers internal POR circuit) Software/Firmware reset External pin assertion (PDn) will generate POR. UBX-15011785 - R05 Pin Definition Page 20 of 47 EMMY-W1 series - Data Sheet 4 Electrical specification Stressing the device above one or more of the ratings listed in the Absolute Maximum Rating section may cause permanent damage. These are stress ratings only. Operating the module at these or at any conditions other than those specified in the Operating conditions section (section 4.2) of the specification should be avoided. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Operating condition ranges define those limits within which the functionality of the device is guaranteed. Where application information is given, it is advisory only and does not form part of the specification. 4.1 Absolute maximum ratings Symbol Description 3V3 VIO1 VIO2 TSTORAGE Power supply voltage 3.3 V I/O supply voltage 1.8 V I/O supply voltage 3.3 V I/O supply voltage 1.8 V I/O supply voltage 3.3 V Storage temperature Table 13: Absolute maximum ratings Min.

-

-

-40 Typ 3.3 1.8 3.3 1.8 3.3 Max. Units 4.0 2.2 4.0 2.2 4.0

+85 V V V V V C The product is not protected against overvoltage or reversed voltages. If necessary, voltage spikes exceeding the power supply voltage specification given in table above must be limited to values within the specified boundaries by using appropriate protection devices. 4.2 Operating conditions Symbol Parameter 3V3 VIO1 VIO2 Power supply voltage 3.3 V I/O supply voltage 1.8V/3.3 V I/O supply voltage 1.8V/3.3 V VDD_NFC NFC antenna input voltage (pins NFC_ANT_P/N) IANT_NFC NFC antenna peak input current (pins NFC_ANT_P/N)) TA Ripple Noise Ambient operating temperature Peak-to-peak voltage ripple on 3V3, VIO1 or VIO2 supply line. The values have been determined in a frequency range from 10 KHz to > 2 MHz [3]. Min. 2.97 1.62 2.97 1.62 2.97

-

-

-40 20 Typ 3.3 1.8 3.3 1.8 3.3

-

-

-

-

Max. 3.63 1.98 3.63 1.98 3.63 3.6 400

+85 Units V V V V V V mA C mV Table 14: Operating conditions Parameter Storage temperature Operation temperature Table 15: Temperature range Min.

-40

-40 Typ Max.

+85

+85 Units C C UBX-15011785 - R05 Electrical specification Page 21 of 47 4.3 Digital pin ratings Symbol Parameter VIH VIL VHYS VOH VOH Imax Input high voltage Input low voltage Input hysteresis Output high voltage Output low voltage Maximum current consumption on each VIO domain Table 16: Digital pin ratings for VIO1 and VIO2 supply domains 4.4 Wi-Fi power consumption Operation mode:

2.4 GHz Wi-Fi TX/RX with BT and NFC in Deep Sleep mode RX 11 Mbps TX 11 Mbps (18 dBm) TX 11 Mbps (8 dBm) RX 54 Mbps TX 54 Mbps (15 dBm) TX 54 Mbps (8 dBm) RX MCS7(HT40) TX MCS7 (HT40, 15 dBm) TX MCS7 (HT40, 8 dBm) EMMY-W1 series - Data Sheet Min. 0.7*VIO

-0.4 100 VIO-0.4

-

-

Max. VIO+0.4 0.3*VIO

-

-

0.4

<5 Units V V mV V V mA Average current, mA12 108 320 240 86 263 229 93 268 235 Table 17: Wi-Fi current consumption during frame transmission for 2.4 GHz on channel 6 Operation mode:

5 GHz Wi-Fi TX/RX with BT and NFC in Deep Sleep mode Average current, mA12 RX 54 Mbps TX 54 Mbps (16 dBm) TX 54 Mbps (8 dBm) RX MCS7 (HT20) TX MCS7 (HT20, 16 dBm) TX MCS7 (HT20, 8 dBm) RX MCS7 (HT40) TX MCS7 (HT40, 11 dBm) TX MCS7 (HT40, 8 dBm) RX MCS8 (VHT20) TX MCS8 (VHT20, 11 dBm) RX MCS9 (VHT40) TX MCS9 (VHT40, 10 dBm) RX MCS9 (VHT80) TX MCS9 (VHT80, 8 dBm) 77 324 238 87 336 242 106 268 248 91 260 108 267 148 372 Table 18: Wi-Fi current consumption during frame transmission for 5 GHz on channel 36 12 Supply 3.3 V. Current measurements during frame transmission. Numbers obtained with IPERF3 UDP traffic data pump. UBX-15011785 - R05 Electrical specification Page 22 of 47 EMMY-W1 series - Data Sheet Operation mode:

Power save modes Power Down WiFi and BT both in Deepsleep WiFi DTIM 1 and BT Deepsleep WiFi DTIM 3 and BT Deepsleep WiFi DTIM 5 and BT Deepsleep Table 19: Wi-Fi power consumption 4.5 Bluetooth power consumption Bluetooth mode with Wi-Fi and NFC in deep sleep mode TX @ 0dBm Average current, mA 0.03 0.17 1.14 0.47 0.34 Average current, mA13 Deep Sleep Mode BT idle SCO HV3 Peak TX SCO HV3 Peak RX HV3 SCO mode ACL sniff 0x800 eSCO link, Master (2-EV3), ACL sniff 0x800 eSCO link, Master (EV3), ACL sniff 0x800 ACL (data pump) DH1 ACL (data pump) DH3 ACL (data pump) DH5 ACL Link, master sniff mode, interval=1.28s (800) ACL Link, master sniff mode, interval=500ms (320) SCO HV3 Average TX @ 4 dBm (external antenna) SCO HV3 Peak TX @ 4 dBm (external antenna) Interlaced scan (= P&I scan) Page & Inquiry scan Page Scan Inquiry Scan LE Advertise @ 1.28s interval Peak LE TX Peak LE RX LE Link (interval=400=1.28s) LE Link (interval=320=1.00s) LE Scan (interval=800=1.28s) LE Scan (interval=640-1.00s) Table 20: Bluetooth power consumption 4.6 NFC power consumption Operation Mode TAG Type 1 TAG Type 2 TAG Type 3 TAG Type 4A Table 21: NFC power consumption 0.17 4.23 18.75 16.50 7.57 6.57 7.69 11.60 14.60 16.40 0.186 0.278 7.83 22.00 0.372 0.667 0.293 0.293 0.196 15.40 12.30 0.204 0.206 0.281 0.311 Average current, mA 3V3 90 95 85 100 13 Supply 3.3V, Average consumption current if not specified otherwise. UBX-15011785 - R05 Electrical specification Page 23 of 47 EMMY-W1 series - Data Sheet 4.7 Radio specifications 4.7.1 Wi-Fi The EMMY-W1 series modules support Wi-Fi standards IEEE 802.11a/b/g/n/ac in 2.4 GHz and 5 GHz radio bands. In the 2.4 GHz band, the EMMY-W1 supports 802.11b/g/n while in 5 GHz band, it supports 802.11a/n/ac. Parameter RF Frequency range Modulation Supported data rates Supported channel bandwidth Supported guard interval (GI) Maximum transmit power Operation Mode 802.11b/g/n 802.11a/n/ac 802.11b 802.11a/g/n/ac 802.11b 802.11a/g 802.11n 802.11ac 802.11ac 802.11n 802.11ac 802.11b 802.11a/g/n/ac Receiver sensitivity 2.4 GHz 802.11b 802.11g 802.11n 5 GHz 802.11a 802.11n 802.11ac 1 Mbps 11 Mbps 20 MHz 40 MHz 20 MHz 40 MHz 80 MHz 6 Mbps 54 Mbps MCS0 MCS7 MCS0 MCS7 6 Mbps 54 Mbps MCS0 MCS7 MCS0 MCS9 MCS0 MCS9 Specification 2.400 2.500 GHz 5.150 5.850 GHz CCK and DSSS OFDM 1, 2, 5.5, 11 Mbps 6, 9, 12, 18, 24, 36, 48, 54 Mbps MCS0 - MCS7 (150 Mbps) MCS0 MCS9 (433 Mbps) 20, 40, 80 MHz 400, 800 ms Short guard interval supported 18 dBm 1.5 dB 16 dBm 1.5 dB

-98 dBm 1 dB

-89 dBm 1 dB

-91 dBm 1 dB

-74 dBm 1 dB

-91 dBm 1 dB

-73 dBm 1 dB

-89 dBm 1 dB

-71 dBm 1 dB

-91 dBm 1 dB

-74 dBm 1 dB

-90 dBm 1 dB

-72 dBm 1 dB

-88 dBm 1 dB

-63 dBm 1 dB

-85 dBm 1 dB

-60 dBm 1 dB Table 22: Wi-Fi radio specifications Channel 1 Frequency, GHz 2.412 2 3 4 5 2.417 2.422 2.427 2.432 Channel 6 Frequency, GHz 2.437 7 8 9 10 2.442 2.447 2.452 2.457 Table 23: 2.4 GHz Band Supported Channels, 20 MHz bandwidth Channel Frequency, GHz 1 - 5 2 - 6 3 - 7 2.422 2.427 2.432 Channel Frequency, GHz 4 - 8 5 - 9 6 - 10 2.437 2.442 2.447 Table 24: 2.4 GHz band supported channels, 40 MHz bandwidth Channel 11 Frequency, GHz 2.462 12 13 2.467 2.472 Channel 7 - 11 Frequency, GHz 2.452 UBX-15011785 - R05 Electrical specification Page 24 of 47 EMMY-W1 series - Data Sheet Channel Frequency, GHz 36 40 44 48 52 56 60 64 5.180 5.200 5.220 5.240 5.260 5.280 5.300 5.320 Channel Frequency, GHz 100 104 108 112 116 120 124 128 5.500 5.520 5.540 5.560 5.580 5.600 5.620 5.640 Table 25: 5 GHz band supported channels, 20 MHz bandwidth Channel Frequency, GHz 36 - 40 44 - 48 52 - 56 60 - 64 5.190 5.230 5.270 5.310 Channel 100 - 104 108 - 112 116 - 120 124 - 128 Frequency, GHz 5.510 5.550 5.590 5.630 Table 26: 5 GHz band supported channels, 40 MHz bandwidth Channel Frequency, GHz 42 58 5.210 5.290 Channel Frequency, GHz 106 122 5.530 5.610 Table 27: 5 GHz band supported channels, 80 MHz bandwidth Channel Frequency, GHz 132 136 140 149 153 157 161 165 5.660 5.680 5.700 5.745 5.765 5.785 5.805 5.825 Channel 132 - 136 149 - 153 157 - 161 Frequency, GHz 5.670 5.755 5.795 Channel Frequency, GHz 138 155 5.690 5.775 4.7.2 Bluetooth Parameter RF Frequency Range Supported Modes Number of channels Modulation Transmit Power Receiver Sensitivity Specifications 2.400 2.4835 GHz Bluetooth v4.2 (including Bluetooth Low Energy and Classic Bluetooth with BR and EDR) 79 1 Mbps: GFSK (BR) 2 Mbps: /4 DQPSK (EDR) 3 Mbps: 8DQPSK (EDR) Class 2, Class 1, BR: 10 dBm 2 dB, EDR: 8 dBm 2 dB14

-95 dBm 2 dB Table 28: Bluetooth radio specifications 4.7.3 LTE co-existence Specific influence of BAW filters on the following RF parameters:

Wi-Fi output power Wi-Fi sensitivity Bluetooth output power Bluetooth sensitivity Characterization of LTE co-existence:

Maximum tolerated input power from LTE interferer Rejection in LTE bands Wi-Fi and Bluetooth desensitization in presence of LTE transmission in adjacent bands for given antenna isolation 14 For regulatory reasons, only class 2 operations are permitted in Europe. UBX-15011785 - R05 Electrical specification Page 25 of 47 EMMY-W1 series - Data Sheet BAW decrease influence to LTE as well The BAW-Filter is included only in the EMMY-W161 module variant. 4.7.4 Near field communication 4.7.4.1 Card emulator specifications Parameter Condition AC characteristics Minimum Type Maximum Units VsensPICC MODPICC DRPICC Input carrier detection level, full-power mode, peak sinus differential voltage on NFC_ANT_P/N pin Input ASK modulation index15 Input data rate (coding depending on standard:

Manchester, Modified, Miller, or NRZ

-

8 106 300

-

-

-

100 848 mVpeak

%

Kbps Table 29: NFC card emulator For typical recommended operating conditions unless otherwise specified. 4.7.4.2 Reader/Writer specifications Parameter Condition Minimum Type Maximum Units DC characteristics VCMTX_PA Power amplifier output common mode level AC characteristics

-

VDDTX/2

-

FTXCARR ROUT_ANT MODPCD Output carrier frequency 13.553 13.56 13.567 Power amplifier output impedance Output ASK modulation index15

-

8 50

-

-

100 V MHz

%

Table 30: NFC Reader/Writer specifications For typical recommended operating conditions unless otherwise specified 15 As defined in ISO/IEC 14443-2, for example, [a-b]/[a+b] where a and b are the peak and minimum signal amplitude respectively. UBX-15011785 - R05 Electrical specification Page 26 of 47 EMMY-W1 series - Data Sheet 5 Host drivers and firmware 5.1 General principle The EMMY-W1 series module does not contain any persistent software. A firmware binary will be downloaded by the host operating system driver on system start-up. 5.2 Supported operating systems 5.2.1 Linux Linux device drivers are available from u-blox. Once you sign the Limited Use License Agreement (LULA) with u-blox, a driver package will be available. This package includes:

Dedicated Kernel driver, to bind the Wi-Fi, Bluetooth and NFC block to the kernel. The sources of those drivers will be provided. A dedicated firmware image, which will be uploaded during initialization. Various configuration tools Laboratory and manufacturing tools For a detailed description of the driver packages, refer to EMMY-W1 series System Integration Manual [3]. UBX-15011785 - R05 Host drivers and firmware Page 27 of 47 EMMY-W1 series - Data Sheet 6 Mechanical specifications Figure 12: EMMY-W1 series dimensions (bottom view) Parameter Description Typical Tolerance A B C ccc D E F G H I J Module Length [mm]

Module Width [mm]

Module Thickness [mm]

Seating Plane Coplanarity [mm]

PCB Edge to Pin Edge [mm]

Pin Width [mm]

Pin Length [mm]

Pin to Pin Pitch [mm]

Horizontal Corner Pin to Pin Pitch [mm]

Lateral Corner Pin to Pin Pitch [mm]

Horizontal Thermal Pads Pitch [mm]

UBX-15011785 - R05 19.8 13.8 2.5 0.15 0.3 0.8 1.2 1.25 1.5 1.65 4.9

(779.5 mil)

+0.35/-0.1

(+13.8/-3.9 mil)

(543.3 mil)

+0.1/-0.1

(+3.9/-3.9 mil)

(98.4 mil)

+0.2/-0.2

(+7.9/-7.9 mil)

(5.9 mil)

(11.8 mil)

+0.20/-0.20

(+7.9/-7.9 mil)

(31.5 mil)

+0.05/-0.05

(+2.0/-2.0 mil)

(47.2 mil)

+0.05/-0.05

(+2.0/-2.0 mil)

(49.2 mil)

+0.02/-0.02

(+0.8/-0.8 mil)

(59.1 mil)

+0.02/-0.02

(+0.8/-0.8 mil)

(65.0 mil)

+0.02/-0.02

(+0.8/-0.8 mil)

(192.9 mil)

+0.02/-0.02

(+0.8/-0.8 mil) Mechanical specifications Page 28 of 47 EMMY-W1 series - Data Sheet Parameter Description Typical Tolerance K L M N O P Thermal Pad Height [mm]

Thermal Pad Length [mm]

3.35 3.7

(131 9 mil)

+0.1/-0.1

(+3.9/-3.9 mil)

(145.7 mil)

+0.1/-0.1

(+3.9/-3.9 mil) Thermal Pad Pin 1 Mark Chamfer [mm]

0.6 x 45

(23.6 mil x 45)

+0.1/-0.1

(+3.9/-3.9 mil) Horizontal Pin to Thermal Pad Pitch [mm]

3.725

(146.7 mil)

+0.05/-0.05

(+2.0/-2.0 mil) Lateral Pin to Thermal Pad Distance [mm]

Lateral Thermal Pads Pitch [mm]

4.1 4.55

(161.4 mil)

+0.05/-0.05

(+2.0/-2.0 mil)

(179.1 mil)

+0.02/-0.02

(+0.8/-0.8 mil) UBX-15011785 - R05 Mechanical specifications Page 29 of 47 EMMY-W1 series - Data Sheet 7 Qualification and approvals Table 31 provides an overview of the available radio type approvals for each EMMY-W1 product variant. Country/Region EMMY-W161 EMMY-W161-A EMMY-W163 EMMY-W163-A EMMY-W165 EMMY-W165-A EU (ETSI) USA (FCC) Canada (IC) Australia (ACMA) Korea (KCC) Japan (Giteki) Yes Yes Yes Yes No No Yes Yes Yes Yes No No Yes Yes Yes No Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes No No No Yes Yes Yes No No No Table 31: Overview of certifications for EMMY-W1 module series 7.1 Approvals16 Products marked with this lead-free symbol on the product label comply with the

"Directive 2002/95/EC of the European Parliament and the Council on the Restriction of Use of certain Hazardous Substances in Electrical and Electronic Equipment" (RoHS). EMMY-W1 series Wi-Fi modules are RoHS compliant. 7.1.1 European Union regulatory compliance Information about regulatory compliance of the European Union for EMMY-W1 modules is available in the EMMY-W1 Declaration of Conformity [4]. 7.1.1.1 Equipment classes A multi-radio module is classified as class-1 or class-2 radio equipment depending on the frequency band in which it can operate. This equipment class is inherited by the end-product that integrates the module, thus it must be marked accordingly. Class-1 radio equipment can be placed on the market and put into service without restrictions.

(Article 1 of Commission Decision 2000/299/EC of April 6 2000) This multi-radio module is defined as class-1 radio equipment when it is restricted to operate in the following frequency bands:

Bluetooth , ISM band 2400 2483.5 MHz WLAN, ISM band 2400 2483.5 MHz WLAN, U-NII band-2e 5470 5725 MHz, exludes 5600-5650 GHz17 Class-2 radio equipment includes restrictions applied by Member States as indicated in Article 1(2) of the Commission Decision. This class uses the Alert Sign as an equipment class identifier. Figure 13: Alert sign to identify equipment Class-2 16 See Table 31 for information on what certifications are completed for each of the EMMY-W1 module versions. 17 Channels 118, 120, 122, 124, 126 and 128 have to be excluded for the EMMY-W1 series modules. The firmware was not approved to operate in frequencies between 5.600 5.650 GHz due to lack of CCA time of 10 min. This might change in future firmware releases. UBX-15011785 - R05 Qualification and approvals Page 30 of 47 EMMY-W1 series - Data Sheet If an end product allows the multiradio module to operate in the 5150-5350 MHz band (WLAN channel: 36-64), it is defined as class-2 radio equipment and must be marked accordingly. Class-2 radio equipment must have the

"alert" sign affixed on the equipment, packaging and printed in the user manual. The EMMY-W1 multiradio module uses harmonized frequency bands thus it is comprised by subclass H01 of class 2 equipment, for which notification in accordance with article 6(4) of the R&TTE directive is not necessary. A definition of subclasses of Class 2 equipment can be found in [15]. The table below shows the restrictions when operating WLAN at different bands within the European countries:

Band Channel number Channel frequency

[MHz]

Indoor use allowed Outdoor use allowed Radio Equipment Class Max. EIRP ISM 1 11 U-NII 1 36 48 2412 2462 5180 5240 U-NII 2 52 64 5260 5320 U-NII 2e 100 140 17 5500 5700 U-NII 3 149 - 165 5750 - 5825 Yes Yes Yes Yes Yes Yes No No Yes Yes 1 2 2 1 1 Table 32: Operating restrictions and radio equipment classification of EMMY-W1 series 100 mW / 20 dBm 200 mW / 23 dBm 200 mW / 23 dBm 1 W / 30 dBm 25 mW / 14 dBm Guidance on how the end product is marked in accordance with the R&TTE directive can be found in the Radio and Telecommunication Terminal Equipment (R&TTE) Directive [15]. IMPORTANT: The CE marking must be affixed on a visible location on the OEM product in which this module is installed and has to be labeled in accordance to R&TTE Directive 1999/5/EC. 7.1.2 FCC compliance The EMMY-W1 series module complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Non-authorized modification could void authority to use this equipment. The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. In accordance with 47 CFR 15.19, the end product into which this module is integrated shall bear the following statement in a conspicuous location on the device:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. When the end-product is so small or for such use that it is not practical to place the above statement on it, the information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or on the container in which the device is marketed. However, the FCC ID label must be displayed on the device. If the end-product will be installed in locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual. The outside of final products containing the EMMY-W1 module must display in a user accessible area a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: (XYZ)(UPN) or Contains FCC ID: (XYZ)(UPN), where (XYZ) represents the UBX-15011785 - R05 Qualification and approvals Page 31 of 47 EMMY-W1 series - Data Sheet FCC Grantee Code and (UPN) is the Unique Product Number decided by the grant owner 18. 7.1.3 IC compliance The EMMY-W1 series module complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Any notification to the end user of installation or removal instructions about the integrated radio module is NOT allowed. Unauthorized modification could void authority to use this equipment. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This radio transmitter IC: 8595A-EMMYW161, IC: 8595A-EMMYW163 and IC: 8595A-EMMYW165 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device; otherwise, the host device must be labeled to display the Industry Canada certification number for the module, preceded by the words Contains transmitter module, or the word Contains, or similar wording expressing the same meaning, as follows: Contains transmitter module IC: (CN)-(UPN), where (CN) is the Company Number registered at Industry Canada and (UPN) is the Unique Product Number decided by the grant owner. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Cet quipement est conforme aux limites d'exposition de rayonnement d'IC RSS-102 dtermines pour un environnement non contrl. Cet quipement devrait tre install et actionn avec la distance minimum 20 cm entre le radiateur et votre corps. Cet metteur radio, IC: 8595A-EMMYW161, IC: 8595A-EMMYW163 et IC: 8595A-EMMYW165 t approuv par Industry Canada pour fonctionner avec les types dantenne numrs ci-dessous avec le gain maximum autoris et limpdance ncessaire pour chaque type dantenne indiqu. Les types dantenne ne figurant pas dans cette liste et ayant un gain suprieur au gain maximum indiqu pour ce type-l sont strictement interdits dutilisation avec cet appareil. Le dispositif de fonctionnement dans la bande 5150-5250 MHz est rserv une utilisation en intrieur pour rduire le risque d'interfrences nuisibles la co-canal systmes mobiles par satellite Opration dans la bande 5600-5650 MHz n'est pas autorise au Canada. Haute puissance radars sont dsigns comme utilisateurs principaux (c.-utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-

5850 MHz et que ces radars pourraient causer des interfrences et / ou des dommages dispositifs LAN-EL. 18 The FCC and IC IDs for the EMMY-W1 series module variants are shown in Table 36. Select the applicable ID. UBX-15011785 - R05 Qualification and approvals Page 32 of 47 EMMY-W1 series - Data Sheet Ltiquette dhomologation dIndustrie Canada dun module donn doit tre pose sur lappareil hte un endroit bien en vue en tout temps. En labsence dtiquette, lappareil hte doit porter une tiquette sur laquelle figure le numro dhomologation du module dIndustrie Canada, prcd des mots Contient un module dmission , ou du mot Contient , ou dune formulation similaire allant dans le mme sens et qui va comme suit : Contient le module dmission IC: (CN)-(UPN) , o (CN) reprsente le numro de compagnie, attribu par Industrie Canada et (UPN) reprsente le numro de produit unique attribu par le requrant. The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. See Table 33 for list of approved antennas. The approval type for all the EMMY-W1 series variants is a modular approval. Due to Industry Canada Modular Approval Requirements (Source: RSP-100 Issue 10), any application which includes the module must be approved by the module manufacturer (u-blox). The application manufacturer must provide design data for the review procedure. 7.1.4 Australia and New Zealand regulatory compliance The EMMY-W1 series modules are compliant with the standards made by the Australian Communications and Media Authority (ACMA). For detailed information about the obligations for end products market in Australia or New Zealand, refer to the EMMY-W1 series System Integration Manual [3]. 7.1.5 Korean KCC compliance MSIP-CRM-ULX-EMMY-W163 The EMMY-W1 series modules are certified by the Korea Communications Commission (KCC). 7.1.6 Japan radio equipment compliance The EMMY-W1 series module complies with the Japanese Technical Regulation Conformity Certification of Specified Radio Equipment (ordinance of MPT N. 37, 1981), Article 2, Paragraph 1:

Item 19 "2.4 GHz band wide band low power data communication system"

Item 19-3 Low power data communications system in the 5.2/5.3 GHz band Item 19-3-2 Low power data communications system in the 5.6 GHz band The EMMY-W1 series module is restricted on the Japanese market to be used indoors only if the product is operating in the 5.2/5.3 GHz band. 207-16EMMY 5GHz band (W52,W53): For indoor use only -

Figure 14 Giteki mark for the EMMY-W1 series modules. UBX-15011785 - R05 Qualification and approvals Page 33 of 47 EMMY-W1 series - Data Sheet 7.2 Approved antennas For Bluetooth and Wi-Fi operation in the 2.4 GHz band and Wi-Fi operation in the 5 GHz band, the module has been tested and approved for use with the antennas listed in Table 33. Manufacturer Part Number Antenna type Peak gain [dBi]

2.4 GHz band 5 GHz band Antenova A10194 SMD chip antenna 10x10x0.9 [mm] [5]

Linx Taoglas Taoglas Walsin Delock ANT-DB1-RAF-RPS Dual-band dipole antenna [6]

GW.40.2153 Dual-band dipole antenna [7]

GW.59.3153 Dual-band dipole antenna [8]

RFDPA870900SBLB8G1 Dual-band dipole antenna [9]

88395 Dual-band dipole antenna [11]

Table 33: List of approved dual-band antennas 1.8 2.5 3.74 2.37 2 1.5 4.1 4.6 2.5 2.93 3 2.1 The module can be integrated with other antennas which the OEM installer must authorize with respective regulatory agencies and after approval of the module manufacturer. Important: To be compliant to FCC 15.407(a) the EIRP is not allowed to exceed 125 mW (21 dBm) at any elevation angle above 30 degrees as measured from the horizon when operate as an outdoor access point in U-NII-1 band, 5.150-5.250 GHz. If in doubt if the antenna installation fulfills this requirement at maximum output power, restrict the maximum output power setting for operation in the 5.150-5.250 GHz band to 16 dBm. For a description on how to configure output power settings refer to the EMMY-W1 series System Integration Manual [3]. 7.2.1 Bluetooth antenna The following antennas are designated for Bluetooth transmission on EMMY-W163:

Manufacturer Part Number Antenna type Peak gain [dBi]

2.4 GHz band 2450AT45A100 SMD chip antenna 10x10x0.9 [mm] [12]

2.2 Johanson Technology Taoglas GW.26.0151 Single-band monopole antenna [13]

Linx Linx ANT-2.4-CW-RCT-RP Single-band dipole antenna [10]

ANT-2.4-CW-RH Single-band monopole antenna [14]

1.8 2.2

-0.9 Table 34: List of approved single-band antennas 7.2.2 NFC antenna The following antennas are designated to be used for Near Field Communication (NFC) on EMMY-W161, EMMY-W163, and EMMY-W165:

Manufacturer Part Number Antenna type u-blox EMMY_NFC_ANT External PCB antenna with connector Table 35: List of approved NFC antenna UBX-15011785 - R05 Qualification and approvals Page 34 of 47 EMMY-W1 series - Data Sheet 7.3 FCC and IC IDs Product name EMMY-W161 EMMY-W161-A EMMY-W163 EMMY-W163-A EMMY-W165 EMMY-W165-A FCC ID XPYEMMYW161 XPYEMMYW161 XPYEMMYW163 XPYEMMYW163 XPYEMMYW165 XPYEMMYW165 Table 36: FCC and IC IDs for different models of EMMY-W1 series 7.4 Korea KCC IDs IC ID 8595A-EMMYW161 8595A-EMMYW161 8595A-EMMYW163 8595A-EMMYW163 8595A-EMMYW165 8595A-EMMYW165 Product name EMMY-W161 EMMY-W161-A EMMY-W163 EMMY-W163-A EMMY-W165 EMMY-W165-A KCC ID

-

-

MSIP-CRM-ULX-EMMY-W163 MSIP-CRM-ULX-EMMY-W163

-

-

Table 37: KCC certification IDs for different models of EMMY-W1 series 7.5 Japan Giteki IDs Product name EMMY-W161 EMMY-W161-A EMMY-W163 EMMY-W163-A EMMY-W165 EMMY-W165-A GITEKI ID

-

-

MIC ID: R 207-16EMMY MIC ID: R 207-16EMMY

-

-

Table 38: Giteki certification IDs for different models of EMMY-W1 series 7.6 Bluetooth qualification The EMMY-W1 series modules is Bluetooth qualified as "Controller Subsystem" and is listed with the qualified design ID, QD ID: 87047. This means that there is no need to do any further qualification if the module is combined with a host stack that is Bluetooth qualified as "Host Subsystem". 7.6.1 Bluetooth host stack Several Bluetooth host stacks are available in the market. These host stacks are suited for different tasks and environments. These host stacks could differ based on their system requirements, supported Bluetooth profiles, cost, Bluetooth qualification, support and so on. UBX-15011785 - R05 Qualification and approvals Page 35 of 47 EMMY-W1 series - Data Sheet 8 Product handling 8.1 Packaging The EMMY-W1 series modules are delivered as hermetically sealed tape and reels, to enable efficient production, production lot set-up and tear-down. For more information about packaging, see the u-blox Package Information Guide [1]. 8.1.1 Reels The EMMY-W1 series modules are deliverable in quantities of 500 pieces on a reel. The EMMY-W1 series modules are shipped on reel Type A as described in the u-blox Package Information Guide [1]. 8.1.2 Tapes Figure 14 shows the position and orientation of the EMMY-W1 modules as they are delivered on tape. The dimensions of the tapes are specified in Figure 16. Sprocket Hole Feed direction Pin 1 Figure 15: Orientation for EMMY-W1 modules on tape UBX-15011785 - R05 Product handling Page 36 of 47 EMMY-W1 series - Data Sheet Figure 16: EMMY-W1 Tape dimensions 8.2 Shipment, storage and handling For more information regarding shipment, storage and handling see the u-blox Package Information Guide [1]. 8.2.1 Moisture sensitivity levels The EMMY-W1 series modules are rated at moisture sensitivity level 3. See moisture sensitive warning label on each shipping bag for detailed information. After opening the dry pack, modules must be mounted within 168 hours in factory conditions of maximum 30C/60%RH or must be stored at less than 10%RH. Modules require baking if the humidity indicator card shows more than 10% when read at 235C or if the conditions mentioned above are not met. Please refer to J-STD-033B standard for bake procedure. 8.2.2 Mounting process and soldering recommendations The EMMY-W1 series module is a surface mount module supplied on a 4-layer FR4-type PCB with gold plated connection pins and produced in a lead-free process with a lead-free soldering paste. The wrap page of the PCB is max. 0,75% according to IPC-A-610E. The thickness of solder resist on the host PCB top side and the EMMY-W1 bottom side must be considered for the soldering process. This module is compatible with industrial reflow profile for RoHS/Pb-free solders, Sn96.5/Ag3.0/Cu0.5 solder is a right choice. Use of "No Clean" soldering paste is strongly recommended, cleaning the populated modules is strongly discouraged - residuals under the module cannot be easily removed with any cleaning process. Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pins. Only a single reflow soldering process is permitted for host boards with the EMMY-W1 series modules. The reflow profile used is dependent on the thermal mass of the entire populated PCB, heat transfer efficiency of the oven and particular type of solder paste used. Since the profile used is process and layout dependent, the optimum profile should be studied case by case. Recommendations below should be taken as a starting point guide. In case of basic information necessity, please refer to J-STD-020C standard. }

UBX-15011785 - R05 Product handling Page 37 of 47 EMMY-W1 series - Data Sheet Profile feature Ramp up rate (TSMAX to TP) Minimum soak temperature (TSMIN) Maximum soak temperature (TSMAX) Soak time (ts) Liquidus temperature (TL) Time above TL (tL) Peak temperature (TP) Sn-Pb eutectic

(Sn63/Pb37) 3 C/sec max 100 C 150 C 60 - 120 sec 183 C 60 - 150 sec 215 225 C Time within +0 / -5C of actual TP (tp) 10 - 30 sec Ramp down rate Time from 25C to TP 6 C/sec max 6 min max Table 39: Recommended reflow profile RoHS/Pb-free

(Sn96.5/Ag3.0/Cu0.5) 3 C/sec max 150 C 200 C 60 - 180 sec 217 C 60 - 150 sec 235 245 C 20 - 40 sec 6 C/sec max 8 min max The lowest value of TP and slower ramp down rate (2 3 C/sec) is preferred. Figure 17: Reflow profile 8.2.3 ESD handling precautions EMMY-W1 series modules are Electrostatic Sensitive Devices (ESD). Observe precautions for handling! Failure to observe these precautions can result in severe damage to the Wi-Fi receiver!

Wi-Fi transceivers are Electrostatic Sensitive Devices (ESD) and require special precautions when handling. Particular care must be exercised when handling patch antennas, due to the risk of electrostatic charges. In addition to standard ESD safety practices, the following measures should be taken into account whenever handling the receiver:

Unless there is a galvanic coupling between the local GND (i.e. the work table) and the PCB GND, then the first point of contact when handling the PCB must always be between the local GND and PCB GND. Before mounting an antenna patch, connect ground of the device UBX-15011785 - R05 Product handling Page 38 of 47 When handling the RF pin, do not come into contact with any charged capacitors and be careful when contacting materials that can develop charges (e.g. patch antenna ~10 pF, coax cable ~50-80 pF/m, soldering iron, ) To prevent electrostatic discharge through the RF input, do not touch any exposed antenna area. If there is any risk that such exposed antenna area is touched in non ESD protected work area, implement proper ESD protection measures in the design. When soldering RF connectors and patch antennas to the receivers RF pin, make sure to use an ESD safe soldering iron (tip). EMMY-W1 series - Data Sheet UBX-15011785 - R05 Product handling Page 39 of 47 EMMY-W1 series - Data Sheet 9 Labeling and ordering information 9.1 Product labeling The labels of EMMY-W1 series include important product information as described in this section. The data matrix code for automotive and professional grade variants of EMMY-W1 series includes a serial number. Figure 18 illustrates the sample label of the automotive grade (professional grade is similar and differs with respect to product version 1 as mentioned in Table 40) of the EMMY-W1 series and includes: the u-blox logo, product name (model), type number, FCC and IC certification number, KCC and GITEKI mark and ID, and the date of unit production encoded YY/WW (year/week). The product label may differ per product type depending on the country approvals obtained for each product type. 1 2 3 4 5 6 7 Figure 18: EMMY-W1 series Sample label A detailed description of the label components are listed in Table 40. The first three digits of the serial number represent the Bluetooth MAC address. UBX-15011785 - R05 Labeling and ordering information Page 40 of 47 EMMY-W1 series - Data Sheet Reference Description 1 2 3 4 5 6 Text MODEL: followed by product type number, excluding the second dash and smaller font used for the product version identifier (For example, xxB-yy for professional and xxA-yy for automotive grade). Date of production encoded YY/WW (year/week) Certification IDs (e.g. FCC/IC, KCC) with which the module has been listed with KC mark for Korea KCC certification if applicable. GITEKI mark and ID if applicable Data Matrix with unique serial number of 19 alphanumeric symbols. The 3 first symbols represent the unique module type no:

631: EMMY-W161-00A-00 632: EMMY-W163-00A-00 700: EMMY-W163-00B-00 701: EMMY-W161-00B-00 756: EMMY-W165-00A-00 841: EMMY-W165-00B-00 The next 12 symbols represent the unique hexadecimal Bluetooth MAC address (see section 1.7 for more information about MAC addresses) of the module AABBCCDDEEFF, and the last 4 symbols represent the hardware and firmware version encoded HHFF. 7 u-blox logo, the red dot in the logo is also marking pin no 1 Table 40 EMMY-W1 series label description 9.2 Explanation of codes Two different product code formats are used. The Product Name is used in documentation such as this data sheet and identifies all u-blox products, independent of packaging and quality grade. The Ordering Code includes options and quality, while the Type Number includes the hardware and firmware versions. Table 41 below details these three different formats:

Format Product Name Ordering Code Type Number Structure PPPP-TGVV PPPP-TGVV-TTQ PPPP-TGVV-TTQ-XX Table 41: Product code formats Table 42 explains the parts of the product code. Code Meaning PPPP TG VV TT Q Form factor Platform T Dominant technology, For example, W: Wi-Fi, B: Bluetooth G - Generation Variant based on the same platform; range [0099]

Major Product Version Quality grade A: Automotive B: Professional C: Standard XX Minor product version (not relevant for certification) Table 42: Part identification code Example EMMY W1 61 00 A 00 UBX-15011785 - R05 Labeling and ordering information Page 41 of 47 EMMY-W1 series - Data Sheet 9.3 Ordering codes Ordering Code Product name Product EMMY-W161-00B EMMY-W161 EMMY-W161 professional grade module EMMY-W161-00A EMMY-W161-A EMMY-W161 automotive grade module EMMY-W163-00B EMMY-W163 EMMY-W163 professional grade module EMMY-W163-00A EMMY-W163-A EMMY-W163 automotive grade module EMMY-W165-00B EMMY-W165 EMMY-W165 professional grade module EMMY-W165-00A EMMY-W165-A EMMY-W165 automotive grade module EVK-EMMY-W161-A EVK-EMMY-W161 Evaluation kit for EMMY-W161 and EMMY-W161-A as well as EMMY-

W165 and EMMY-W165-A when not co-located with LTE EVK-EMMY-W163-A EVK-EMMY-W163 Evaluation kit for EMMY-W163 and EMMY-W163-A Table 43: Product ordering codes Product changes affecting form, fit or function are documented by u-blox. For a list of Product Change Notifications (PCNs) see our website. UBX-15011785 - R05 Labeling and ordering information Page 42 of 47 EMMY-W1 series - Data Sheet Appendix A Glossary Name ACL AES BPF BT BAW CPU DTIM DC DDR EIRP ESD EMV FCC FIFO GI GND GPIO HD HCI IC IMEI LED LTE LE MAC MWS MCS MSL NFC NFCIP OEM P2P PCB PCN PCM R&TTE RF RSS RH RoHS SDIO Definition Access control list Advanced Encryption Standard Band-Pass Filter Bluetooth Bulk Acoustic Wave Central Processing Unit Delivery traffic indication message Direct Current Double Data Rate Equivalent Isotropically Radiated Power Electrostatic Sensitive Devices Europay, MasterCard and Visa Federal Communications Commission First In, First Out Guard interval Ground General-purpose input/output High Definition Host Controller Interface Industry Canada International Mobile Station Equipment Identity Light-emitting diode Long Term Evolution Low Energy Medium Access Control Mobile Wireless Standards Modulation Coding Scheme Moisture sensitivity level Near-Field Communication NFC Interface and Protocol Original equipment manufacturer Peer-to-peer Printed Circuit Board Product Change Notification Pulse-code modulation Radio and telecommunications terminal equipment Radio Frequency Radio Standards Specification Relative humidity Restriction of Hazardous Substances Secure Digital Input Output UBX-15011785 - R05 Appendix Page 43 of 47 EMMY-W1 series - Data Sheet Name SDR SMD SCO UART Definition Secure Digital Rate Surface-mount Device Synchronous Connection-Oriented Universal Asynchronous Receiver/Transmitter Table 44: Explanation of abbreviations and terms used UBX-15011785 - R05 Appendix Page 44 of 47 EMMY-W1 series - Data Sheet Related documents

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

u-blox Package Information Guide, document number UBX-14001652 Driver Software Application Note for ELLA-W1 series and EMMY-W1 series, document number UBX-15012542 EMMY-W1 series System Integration Manual, document number UBX-15024929 EMMY-W1 Declaration of Conformity, document number UBX-16007139 Mixtus A10194 Product Specification, Antenova-M2M, http://www.antenova-

m2m.com/documents/download/40c67cf2e7a4c7b8cd0f7faed7f6d2ca4fe1886d597d5, October 2015 ANT-DB1-RAF-xxx Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-db1-

raf-xxx.pdf, October 2015 Specification. Part No.: GW.40.2153, taoglas, https://fccid.io/pdf.php?id=2415249, December 2015 Specification. Part No.: GW.59.3153, taoglas, http://www.taoglas.com/images/product_images/original_images/GW.59.3153- 2.4GHz-5.8GHz Band Mount Dipole Antenna 080910.pdf, October 2015 2015 RF Devices and High Frequency Inductors Product catalog, http://www.passivecomponent.com/document/HF_Devices/2013RF_Catalogue.pdf, December 2015 ANT-2.4-CW-RCT-xx Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-

2.4-cw-rct-xx.pdf, October 2015 Delock WLAN 802.11 ac/a/b/g/n Antenna RP-SMA 2 dBi Omnidirectional Joint, 2015-11-26 http://www.delock.com/produkt/88395/pdf.html?sprache=en, November 2015 2.45 GHz High Gain SMD Chip Antenna P/N 2450AT45A100, Johanson Technology, http://www.johansontechnology.com/datasheets/antennas/2450AT45A100.pdf, October 2015 2.4 GHz Miniature Screw mount Monopole Antenna, taoglas, http://www.taoglas.com/images/product_images/original_images/GW.26.0112 2.4GHz Band Monopole SMA%28M%29RA.pdf, December 2015 ANT-2.4-CW-RH Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-2.4-cw-

rh-xxx.pdf, December 2015 Radio and Telecommunication Terminal Equipment (R&TTE) Directive;

http://ec.europa.eu/growth/sectors/electrical-engineering/rtte-directive; July 2016 For regular updates to u-blox documentation and to receive product change notifications, register on our homepage (http://www.u-blox.ch/). UBX-15011785 - R05 Related documents Page 45 of 47 EMMY-W1 series - Data Sheet Revision history Revision Date Name Comments R01 R02 16-Mar-2015 lalb Initial draft release. 16-Oct-2015 shoe, ishe, kfra, ovik, ddie, kgom Professional grade variants added. Minor updates in section 1.6. Modified figures 2, 11 and 12. Included subsections 2.2, 2.4 and 4.6. Included Table 7 in section 2.3, Table 9 in section 2.4.1 and Table 10 in Section 2.5. Updated Tables 2, 10, 11, 18, and 23. Renamed section 2.5 as GPIO interface. Added information for the sections 2.3, 2.4 and 2.5. Removed section 4.4 - Current consumption from R01. Added section 3.2 Reset configuration, section 4.4 - Wi-Fi power consumption, section 4.5 - Bluetooth power consumption and section 4.6 - NFC power consumption. Removed VIO1/2 from PDn description. Added maximum ratings for NFC_ANT_N/P pins. Added note with respect to availability of BAW in EMMY-

W161 variant only. Updated features to include compliance with Bluetooth 4.2. Included sample labels for professional and automotive grade variants in section 9.1. Modified Wi-Fi standards support in section 4.7.1. Included NFC specifications and packaging information in section 4.7.4 and 8.1 respectively. Minor change in section 7.1.3 IC compliance. Modified the top view drawing in Figure 12. Added info about upcoming country approvals for Japan, South Korea, China, Taiwan and Australia. Added section 7.2 Approved antennas. Provided reference to EMMY-W1 series System Integration Manual for information about driver packages in section 5.2.1. Updated planned FCC and IC IDs in Table 36 and on the label (Figure 18 and 17). Included Receiver Sensitivity information in Table 28. Modified section 1.5. In section 1.6.1, included footnote that IEEE 802.11k and v is not supported by the firmware currently in the first bullet. Removed "applies only to automotive grade variants" from the last bullet in section 1.6.4 as ISO 16750 will apply for both the variants. Added section 1.7. In sections 4.7.1 and 4.7.2, modified the specifications for maximum transmit power and receiver sensitivity. Updated Table 30 in section 7.1.4. Updated section 7.1.4. Modified the Note in section 7.1.2 - "FCC Compliance". Modified the last note in section 7.1.3. Early Production Information document status. Specified the final FCC and IC IDs (Table 36). Added measured ripple noise values. Updated label description with matrix code information (section 9.1). Included information about EMMY-W165 product variant. Added information about the restrictions for U-NII band 3 in Table 32. Corrected the description of the data matrix code on the module label (Table 40) and added EMMY-W165-00B to the table. Removed the note that states FCC, ETSI and IC certifications are in progress as they are completed now. Updated power consumption values for Wi-Fi, Bluetooth and Bluetooth low energy

(sections 4.4 and 4.5). Added BT QDID (section 7.6). Added maximum current consumption for VIO related PINS (section 4.3). Updated Bluetooth sensitivity value

(section 4.7.2). Added PCM_MCLK as optional function for GPIO3 (section 3.1). Updated tolerance for mechanical specifications (section 6). Added footnote to explain exclusion of frequencies 5600-5650 for ETSI in section 7.1.1. Added KCC IDs and compliance notes (section 7.1.5 and 7.4). Added Australia and New Zealand compliance notes (section 7.1.4). Added Japan GITEKI compliance notes

(section 7.5 and 7.1.6). Added tape orientation information (section 8.1.2). Moved the Declaration of Conformity information to a separate EMMY-W1 Declaration of Conformity document (section 7.1.1). Replaced Document status with Disclosure restriction Added requirement for outdoor use as an Wi-Fi access point in the 5.15-5.25 GHz band (section 7.2). Extended the Glossary. R03 9-Dec-2015 shoe, ishe, kgom R04 19-Jul-2016 shoe, kgom R05 15-Dec-2016 shoe, lalb, kgom R06 08-Feb-2017 ddie UBX-15011785 - R05 Revision history Page 46 of 47 Contact For complete contact information visit us at www.u-blox.com. u-blox Offices North, Central and South America u-blox America, Inc. Phone:

E-mail:

+1 703 483 3180 info_us@u-blox.com Regional Office West Coast:

Phone:

E-mail:

+1 408 573 3640 info_us@u-blox.com Technical Support:

Phone:

E-mail:

+1 703 483 3185 support_us@u-blox.com Headquarters Europe, Middle East, Africa u-blox AG Phone:

E-mail:

Support:

+41 44 722 74 44 info@u-blox.com support@u-blox.com EMMY-W1 series - Data Sheet Asia, Australia, Pacific u-blox Singapore Pte. Ltd. Phone:

E-mail:

Support:

+65 6734 3811 info_ap@u-blox.com support_ap@u-blox.com Regional Office Australia:

Phone:

E-mail:

Support:

+61 2 8448 2016 info_anz@u-blox.com support_ap@u-blox.com Regional Office China (Beijing):

Phone:

E-mail:

Support:

+86 10 68 133 545 info_cn@u-blox.com support_cn@u-blox.com Regional Office China (Chongqing):

Phone:

E-mail:

Support:

+86 23 6815 1588 info_cn@u-blox.com support_cn@u-blox.com Regional Office China (Shanghai):

Phone:

E-mail:

Support:

+86 21 6090 4832 info_cn@u-blox.com support_cn@u-blox.com Regional Office China (Shenzhen):

Phone:

E-mail:

Support:

+86 755 8627 1083 info_cn@u-blox.com support_cn@u-blox.com Regional Office India:

Phone:

E-mail:

Support:

+91 80 4050 9200 info_in@u-blox.com support_in@u-blox.com Regional Office Japan (Osaka):

Phone:

E-mail:

Support:

+81 6 6941 3660 info_jp@u-blox.com support_jp@u-blox.com Regional Office Japan (Tokyo):

Phone:

E-mail:

Support:

+81 3 5775 3850 info_jp@u-blox.com support_jp@u-blox.com Regional Office Korea:

Phone:

E-mail:

Support:

+82 2 542 0861 info_kr@u-blox.com support_kr@u-blox.com Regional Office Taiwan:

Phone:

E-mail:

Support:

+886 2 2657 1090 info_tw@u-blox.com support_tw@u-blox.com UBX-15011785 - R05 Contact Page 47 of 47

 

 

locate, communicate, accelerate EMMY-W1 Antenna reference design Topic :

EMMY-W1 Antenna reference design Doc.No:

UBX-16015910 Revision R01 Date:

Name Created 01-Jul-2016 Stefano Bianconi Checked Released Signature sbia We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly forbidden. 2016 u-blox AG 1 Scope This document defines the essential specifications necessary to implement the EMMY-W1 antenna reference designs. The information contained herein and its references should be sufficient to guide a skilled person in an attempt to implement the design on a host carrier. It will provide the designer with PCB layout details and expected performance specifications. The document supports the four different PCB designs for Wi-Fi:

Two connector-based designs for the use of external antennas (one for each antenna pin of the module) Two designs based on SMD antennas (one for each antenna pin of the module) This document also supports general guidelines for the design of the NFC interface. 2 FCC/IC ID reference Model EMMY-W161 EMMY-W163 FCC ID IC ID XPYEMMYW161 XPYEMMYW163 8595A-EMMYW161 8595A-EMMYW163 Table 1: FCC and IC IDs for different models of EMMY-W1 series EMMY-W1 Antenna reference design UBX-16015910 Page 1 of 12 locate, communicate, accelerate 3 General description When using the EMMY-W1 together with this antenna reference design, the circuit trace layout must be made in strict compliance with the instructions below. All the components placed on each RF trace must be kept as indicated in the reference design, even if not used. The PCB areas of unused reference designs must be flooded with ground. 1 2 Figure 1: Antenna Reference design embedded in a host carrier PCB Reference Description 1 2 Host carrier PCB (light green) Antenna reference design (dark green) EMMY-W1 Antenna reference design UBX-16015910 Page 2 of 12 locate, communicate, accelerate 3.1 Floor plan and PCB stack-up This section describes where the critical components are positioned on the reference design. It also presents the stack-up of the four layers of the PCB. 10 3 4 5 6 7 8 9 Figure 2: EMMY-W1 antenna reference design Description SMD antenna Antenna impedance matching network Connectors for external antenna Antenna coplanar microstrip, matched to 50 Top layer GND-plane Antenna impedance matching network SMD antenna ELLA-W1 module Reference 3 4 5 6 7 8 9 10 EMMY-W1 Antenna reference design UBX-16015910 Page 3 of 12 locate, communicate, accelerate 3.2 PCB stack-up The stack-up used in the reference design is specified in Table 2. PCB Layer Soldermask Top Top Dielectric L2 Dielectric L3 Dielectric Bottom Material Generic LPI Soldermask Copper Foil Pre-preg 2x7628 Copper Foil Core Copper Foil Pre-preg 2x7628 Copper Foil Soldermask Bottom Generic LPI Soldermask Table 2: Stack-up of EVK-EMMY-W1 Thickness 25 m 35 m 360 m 35 m 700 m +/-10%

35 m 360 m 35 m 25 m 3.2.1 RF trace specification The 50 coplanar micro-strip dimensions used in these reference designs are stated in Figure 3 and Table 3. Figure 3: Coplanar micro-strip dimension specification Item S W T H Value 400 m 600 m 35 m 360 m Table 3: Coplanar micro-strip specification 3.3 Mechanical dimensions The Mechanical dimensions and position of the components are specified in Figure 4. The layers beneath the top layer have the same dimensions and are filled with ground. No RF traces are routed in those layers. EMMY-W1 Antenna reference design UBX-16015910 Page 4 of 12 locate, communicate, accelerate Figure 4: Mechanical dimensions of EVK-EMMY-W1, top layer EMMY-W1 Antenna reference design UBX-16015910 Page 5 of 12 locate, communicate, accelerate 4 Reference designs for antenna pin 1 This section describes the available designs for the antenna pin 1 of the EMMY-W1 modules. Figure 5: Reference schematic for antenna pin 1 4.1 Internal antenna The reference design with internal antenna uses the SMD Antenova type A10194 dual band antenna that is connected to the module RF-port via a coplanar micro-strip transmission line. 4.1.1 Bill of materials Reference designator Description Manufacturer P/N Antenna CHIP 2.45 & 5 GHz Antenova A10194 IND, Multilayer Ceramic, 10nH, +/-5%, 300mA, SMD 0402 Johanson Technology L-07C10NJV6ST IND, Multilayer Ceramic, 1nH, +/-0.3nH, 300mA, SMD 0402 Johanson Technology L-07C1N0SV6T CAP, CER, 0.2pF, +/-0.1pF, C0G, 50V, SMD 0402 Johanson Technology 500R07S0R2BV4 A1 L1 L2 C2 R1 R2 J7 0 resistor, 0402 Do not Assembly Do Not Assembly 4.1.2 Antenna characteristics Parameter Frequency Range Peak Gain VSWR Efficiency Polarisation Low band 2.4 2.5 1.8

< 1.4:1

>75 Linear Radiation pattern Omnidirectional Temperature range

-40 to +85 Impedance Dimension

(L x W x H) 50 10.0 x 10.0 x 0.9 Generic

-

-

High band 4.9 5.875 4.1

< 1.8:1

>60

-

-

-

Unit GHz dBi

-

%

-

-

C mm EMMY-W1 Antenna reference design UBX-16015910 Page 6 of 12 4.2 External antenna locate, communicate, accelerate The reference design with external antenna uses the micro coaxial connector that is connected to the external antenna via a 50 pigtail. See section 6 for a list of available external antennas. 4.2.1 Bill of materials Reference designator Description Do Not Assembly Do Not Assembly Do Not Assembly Do Not Assembly Do Not Assembly 0 resistor, 0402 Coaxial Connector, 0 6 GHz, SMD A1 L1 L2 C2 R1 R2 J7 Manufacturer P/N

-

-

-

-

-

Generic Hirose

-

-

-

-

-

-

U.FL-R-SMT-1(10) EMMY-W1 Antenna reference design UBX-16015910 Page 7 of 12 locate, communicate, accelerate 5 Reference designs for antenna pin 2 This section describes the available designs for the antenna pin 2 of the EMMY-W1 modules. Figure 6: Reference schematic for antenna pin 2 5.1 Internal antenna The reference design with internal antenna uses the SMD Johanson Technology type 2450AT45A100 antenna that is connected to the module RF-port via a coplanar micro-strip transmission line. 5.1.1 Bill of materials Reference designator Description Manufacturer P/N A2 C3 C4 L3 R9 R10 J8 Antenna CHIP 2.4-2.5GHz Johanson Technology 2450AT45A100 CAP, CER, 2.2pF, +/-0.1pF, C0G, 50V, SMD 0402 Johanson Technology 500R07S2R2BV4 CAP, CER, 1.8pF, +/-0.1pF, C0G, 50V, SMD 0402 Johanson Technology 500R07S1R8BV4 IND, Multilayer Ceramic, 3.9nH, +/-0.3nH, 300mA, SMD 0402 Johanson Technology L-07C3N9SV6T 0 resistor, 0402 Do not Assembly Do Not Assembly Generic

-

-

-

-

-

5.1.2 Antenna characteristics Parameter Frequency Range Peak Gain VSWR Polarisation Radiation pattern Temperature range Impedance Dimension

(L x W x H) Low band 2.4 2.5 2.2

< 2:1 Linear Omnidirectional

-40 to +125 50 9.5 x 2.0 x 1.2 Unit GHz dBi

-

-

-

C mm EMMY-W1 Antenna reference design UBX-16015910 Page 8 of 12 5.2 External antenna locate, communicate, accelerate The reference design with external antenna uses the micro coaxial connector that is connected to the external antenna via a 50 pigtail. See section 6 for a list of available external antennas. 5.2.1 Bill of materials Reference designator Description A2 C3 C4 L3 R9 R10 J8 Do not Assembly Do Not Assembly Do not Assembly Do not Assembly Do Not Assembly 0 resistor, 0402 Coaxial Connector, 0 6 GHz, SMD Manufacturer P/N

-

-

-

-

-

Generic Hirose

-

-

-

-

-

-

U.FL-R-SMT-1(10) EMMY-W1 Antenna reference design UBX-16015910 Page 9 of 12 locate, communicate, accelerate 6 Approved external antenna list For Bluetooth operation on EMMY-W163, the module has been tested and approved for use with antennas listed in Table 4. Model name Manufacturer and description ANT-2.4-CW-RCT-RP Linx, Single-band dipole antenna ANT-2.4-CW-RH Linx, Single-band monopole antenna GW.26.0151 Taoglas, Single-band dipole antenna Table 4: Approved antennas list, single-band operation Gain [dBi] (peak) 2.2 @ 2.4GHz band N/A @ 5GHz band

-0.9 0.0 For Bluetooth and Wi-Fi operations in the 2.4 GHz band and Wi-Fi operation in the 5 GHz band, the module has been tested and approved for use with antennas listed in Table 5. Model name Manufacturer and description ANT-DB1-RAF-RPS Linx, Dual-band dipole antenna GW.40.2153 Taoglas, Dual-band dipole antenna GW.59.3153 Taoglas, Dual-band dipole antenna RFDPA870900SBLB8G1 Walsin, Dual-band dipole antenna 88395 Delock, Dual-band dipole antenna Table 5: Approved antennas list, dual-band operation Gain [dBi] (peak) 2.5 @ 2.4GHz band 4.6 @ 5GHz band 3.74 @ 2.4GHz band 2.5 @ 5GHz band 2.37 @ 2.4GHz band 2.93 @ 5GHz band 2 @ 2.4GHz band 3 @ 5GHz band 1.5 @ 2.4GHz band 2.1 @ 5GHz band EMMY-W1 Antenna reference design UBX-16015910 Page 10 of 12 locate, communicate, accelerate 7 NFC reference design This section describes the available design for the NFC coil antenna of the EMMY-W1 modules. Figure 7: Reference schematic for NFC coil antenna 7.1 Internal antenna The reference design uses a NFC coil antenna designed by u-blox. 7.1.1 Bill of materials Reference designator Description J6 C10 C11 C12 C13 C14 C15 Pin Header, Pitch 2.54mm, 1x4 Way, Through Hole Do Not Place CAP, CER, 220pF, 5%, NP0, 50V, SMD 0402 CAP, CER, 820pF, 5%, NP0, 50V, SMD 0402 Do Not Place CAP, CER, 820pF, 5%, NP0, 50V, SMD 0402 Do Not Place 7.1.2 NFC coil characteristics Parameter Frequency Range Number of turns Trace width Trace spacing (edge to edge) Low band 13.56 4 0.4 0.4 Dimensions (L x W) 30 x 30 Manufacturer P/N Samtec

-

Murata Murata

-

Murata

-

TSW-104-07-G-S

-

GRM1555C1H221JA01 GRM1555C1H821JA01

-

GRM1555C1H821JA01

-

Unit MHz

-

mm mm mm EMMY-W1 Antenna reference design UBX-16015910 Page 11 of 12 locate, communicate, accelerate Figure 8: EMMY-W1 reference coil antenna, mechanical dimensions EMMY-W1 Antenna reference design UBX-16015910 Page 12 of 12

 

 

EMMY-W1 series Host-based multiradio modules with Wi-

Fi, Bluetooth and NFC User Manual Abstract This technical data sheet describes the EMMY-W1 series modules with Wi-Fi 802.11ac, Bluetooth v4.2 (Bluetooth Smart Ready) and Near-Field Communication (NFC) designed for both simultaneous and independent operations. These modules include an integrated MAC/baseband processor and RF front-end components and can connect to a host processor through SDIO 3.0 or high-speed UART interfaces. A PCM interface is available for Bluetooth audio applications. These modules are offered in both professional and automotive grades. www.u-blox.com UBX-16015271 - R03 EMMY-W1 series - User Manual Document Information Title Subtitle EMMY-W1 series Host-based multiradio modules with Wi-Fi, Bluetooth and NFC Document type User Manual Document number UBX-16015271 Revision and date R03 05-July-2016 Document status Product Information Document status explanation Objective Specification Document contains target values. Revised and supplementary data will be published later. Advance Information Document contains data based on early testing. Revised and supplementary data will be published later. Early Production Information Document contains data from product verification. Revised and supplementary data may be published later. Production Information Document contains the final product specification. This document applies to the following products:

Product name Type number ROM/FLASH version PCN / IN reference EMMY-W161 EMMY-W161-00B-00 EMMY-W161-00B EMMY-W161-A EMMY-W161-00A-00 EMMY-W161-00A EMMY-W163 EMMY-W163-00B-00 EMMY-W163-00B EMMY-W163-A EMMY-W163-00A-00 EMMY-W163-00A EMMY-W165 EMMY-W165-00B-00 EMMY-W165-00B EMMY-W165-A EMMY-W165-00A-00 EMMY-W165-00A N/A N/A N/A N/A N/A N/A u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or any part thereof without the express permission of u-blox is strictly prohibited. The information contained herein is provided as is and u-blox assumes no liability for the use of the information. No warranty, either express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose of the information. This document may be revised by u-blox at any time. For most recent documents, visit www.u-blox.com. Copyright 2016, u-blox AG. u-blox is a registered trademark of u-blox Holding AG in the EU and other countries. ARM is the registered trademark of ARM Limited in the EU and other countries. UBX-16015271 - R03 Product Information Page 2 of 46 EMMY-W1 series - User Manual Contents Contents .............................................................................................................................. 3 1 Functional description .................................................................................................. 5 1.1 Overview .............................................................................................................................................. 5 Applications .......................................................................................................................................... 5 1.2 Product features ................................................................................................................................... 6 1.3 1.4 Block diagrams ..................................................................................................................................... 6 Product description ............................................................................................................................... 7 1.5 Supported features ............................................................................................................................... 8 1.6 1.6.1 Wi-Fi features ................................................................................................................................ 8 Bluetooth features ......................................................................................................................... 8 1.6.2 NFC features ................................................................................................................................. 8 1.6.3 1.6.4 General product features ............................................................................................................... 8 Compliance ................................................................................................................................... 9 1.6.5 Additional reserved MAC addresses ...................................................................................................... 9 1.7 2 2.2.1 2.2.2 2.2.3 2.2.4 Interfaces .................................................................................................................... 10 2.1 Operation mode configuration ........................................................................................................... 10 SDIO interface .................................................................................................................................... 10 2.2 Default speed and High speed modes ......................................................................................... 10 SDR12, SDR25, SDR50 Modes (up to 100 MHz) (1.8 V) ............................................................... 11 SDR104 Mode (208 MHz) (1.8 V) ................................................................................................ 12 DDR50 Mode (50 MHz) (1.8 V) .................................................................................................... 13 High Speed UART interface ................................................................................................................. 14 PCM interface ..................................................................................................................................... 15 PCM interface specifications ........................................................................................................ 15 2.5 GPIO interface .................................................................................................................................... 16 2.3 2.4 2.4.1 3 Pin Definition .............................................................................................................. 18 Pin description .................................................................................................................................... 18 Reset configuration............................................................................................................................. 19 3.1 3.2 4 Electrical specification ................................................................................................ 20 Absolute maximum ratings ................................................................................................................. 20 4.1 4.2 Operating conditions .......................................................................................................................... 20 4.3 Digital pin ratings ............................................................................................................................... 21 4.4 Wi-Fi power consumption ................................................................................................................... 21 Bluetooth power consumption ........................................................................................................... 22 4.5 NFC power consumption .................................................................................................................... 22 4.6 Radio specifications ............................................................................................................................ 23 4.7 4.7.1 Wi-Fi ........................................................................................................................................... 23 Bluetooth .................................................................................................................................... 28 4.7.2 UBX-16015271 - R03 Product Information Contents Page 3 of 46 EMMY-W1 series - User Manual 4.7.3 4.7.4 LTE co-existence .......................................................................................................................... 28 Near field communication ........................................................................................................... 28 5 Host drivers and firmware ......................................................................................... 30 5.1 General principle ................................................................................................................................ 30 Supported operating systems .............................................................................................................. 30 5.2 Linux ........................................................................................................................................... 30 5.2.1 6 Mechanical specifications .......................................................................................... 31 7.1 7.1.1 7.1.2 7.1.3 7 Qualification and approvals ...................................................................................... 32 Approvals ........................................................................................................................................... 32 European Union regulatory compliance ....................................................................................... 32 FCC compliance .......................................................................................................................... 33 IC compliance.............................................................................................................................. 34 Approved antennas ............................................................................................................................ 35 Bluetooth antenna ...................................................................................................................... 36 NFC antenna ............................................................................................................................... 36 FCC and IC IDs (planned) .................................................................................................................... 36 Certification in other countries ........................................................................................................... 36 7.2.1 7.2.2 7.3 7.4 7.2 8.1 8.1.1 8.1.2 8 Product handling ........................................................................................................ 37 Packaging ........................................................................................................................................... 37 Reels ........................................................................................................................................... 37 Tapes .......................................................................................................................................... 37 Shipment, storage and handling ......................................................................................................... 37 8.2.1 Moisture sensitivity levels ............................................................................................................. 37 8.2.2 Mounting process and soldering recommendations ..................................................................... 38 8.2.3 ESD handling precautions ............................................................................................................ 39 8.2 9 Labeling and ordering information ........................................................................... 40 Product labeling .................................................................................................................................. 40 9.1 9.2 Explanation of codes........................................................................................................................... 41 9.3 Ordering codes ................................................................................................................................... 41 Appendix .......................................................................................................................... 42 A Glossary ...................................................................................................................... 42 Related documents........................................................................................................... 44 Revision history ................................................................................................................ 45 Contact .............................................................................................................................. 46 UBX-16015271 - R03 Product Information Contents Page 4 of 46 EMMY-W1 series - User Manual 1 Functional description 1.1 Overview The EMMY-W1 series provides a complete short range transceiver solution that can easily be integrated into automotive and industrial applications. The modules are designed for both simultaneous and independent operation of the following technologies:

IEEE 802.11a/b/g/n/ac payload data rates for Wi-Fi Dual-mode Bluetooth v4.2 NFC The EMMY-W1 series is a surface-mount device (SMD) component and can be used as a Wi-Fi micro-access point supporting up to 10 clients. A coexistence feature on chip level improves parallel use of Bluetooth and Wi-Fi communication. For highest throughput and performance, a module variant with separated Wi-Fi and Bluetooth antenna pin is also available. The modules include an integrated MAC/baseband processor and RF front-end components and can connect to a host processor through SDIO 3.0 and high-speed UART interfaces. The EMMY-W1 series are offered in automotive and professional grades (see 9.3 Ordering codes and 1.4 Block diagrams). The automotive grade variant includes an automotive-qualified (AEC-Q100) chipset. A host driver for Linux 3.x is available free of charge. The modules are radio type approved1 for Europe (ETSI R&TTE), US (FCC CFR 47 part 15 unlicensed modular transmitter approval) and Canada (IC RSS). Regulatory approvals for using this module in Japan, South Korea, China, Taiwan and Australia will follow. 1.2 Applications Automotive applications High definition (HD) video streaming (headrest displays, rear-view camera) and in-car gaming Rapid sync-n-go applications and fast content download to the vehicle Hands-free equipment (Bluetooth) Personalized adjustment of comfort functions through NFC Industrial applications Manufacturing floor automation, wireless control terminals and point-to-point backhaul Outdoor content distribution Mobile video streaming Robust wireless connectivity in a broad range of industrial applications 1 Approvals are pending UBX-16015271 - R03 Product Information Functional description Page 5 of 46 EMMY-W1 series - User Manual 1.3 Product features Model Radio Interfaces Power Connectors Features Grade 3 1

-

1 s l e n n a h c z H G 4

. 2 i F

-

i W 5 6 1

-

6 3 s l e n n a h c z H G 5 i F

-

i W i n p a n n e t n a t a r e w o p t u p t u o x a M n o i s r e v 1 1

. 2 0 8 E E E I i F

-

i W n o i t a c i f i l a u q h t o o t e u B l s e l i f o r p h t o o t e u B l C F N T R A U d e e p s

-

h g H i 0

. 3 O D S I r e t l i f E T L e p y t a n n e t n A i

) o d u a h t o o t e u B

(

l M C P EMMY-W161 a/b/g/n/ac v4.2 H 18 dBm 1p EMMY-W163 a/b/g/n/ac v4.2 H 18 dBm 2p EMMY-W165 a/b/g/n/ac v4.2 H 18 dBm 1p V 6

. 3

-

0

. 3

:

y l p p u s r e w o P y r o m e m P T O n i s r e t e m a r a p F R y r o m e m P T O n i s e s s e r d d a C A M t r o p p u s e r a w d r a h S E A i t n o P s s e c c A o r c i M l a n o i s s e f o r P e v i t o m o t u A d r a d n a t S i s n p r e d o S l H = HCI 1p = One pin for combined external antenna for Bluetooth and Wi-Fi Table 1: EMMY-W1 series main features summary 2p = Two pins for separate external antennas for Bluetooth and Wi-Fi 1.4 Block diagrams The block diagrams of the EMMY-W1 series are provided in this section. Figure 1: EMMY-W161/EMMY-W165 block diagram - Single antenna variant UBX-16015271 - R03 Product Information Functional description Page 6 of 46 MAC/BB/RADIO2.4GHz WLAN TX2.4GHz WLAN/BT RXBT TXWLAN &BT ANT5GHz WLAN TX/RX5GHz BPF &DIPLEXER2.4GHzBPFEMMY-W161 / EMMY-W165SDIO37.4 MHzCrystalVIO1UARTVIO2PCMVIO2BT LTE COEXVIO2BT LEDWLAN LEDPDnSP3T3.3VVIO1VIO2GNDNFCCOILVIO2GPIOsDC/DC3.3V1.8V1.1V EMMY-W1 series - User Manual In EMMY-W161, the band pass filter (2.4 GHz BPF) is a BAW filter that enables co-existence with LTE. For the variant EMMY-W165, the band pass filter provides no co-existence protection against a co-located LTE transmitter. Figure 2: EMMY-W163 block diagram - Dual-antenna variant In EMMY-W163, the bandpass filters (2.4 GHz BPF) are ceramic bandpass filters. An LTE co-existence variant is not available in the dual-antenna configuration. 1.5 Product description Model Description EMMY-W161 EMMY-W163 EMMY-W165 Professional grade module with 1 combined antenna pin for Wi-Fi and Bluetooth and integrated LTE filter Professional grade module with 2 separate antenna pins for Wi-Fi and Bluetooth (no LTE filter) Professional grade module with 1 combined antenna pin for Wi-Fi and Bluetooth (no LTE filter) EMMY-W161-A Automotive grade module with 1 combined antenna pin for Wi-Fi and Bluetooth and integrated LTE filter EMMY-W163-A Automotive grade module with 2 separate antenna pins for Wi-Fi and Bluetooth (no LTE filter) Automotive grade module with 1 combined antenna pin for Wi-Fi and Bluetooth (no LTE filter) The EMMY-W161 is recommended for applications that have co-located Wi-Fi, Bluetooth and LTE antennas and require co-existence of these wireless technologies. This module provides a dedicated BAW bandpass filter instead of the ceramic bandpass filter. This filter rejects the adjacent LTE bands B40, B7, B41 and B38. The integrated BAW filter is available only for the single-antenna configuration

(EMMY-W161). The module pinout, operating conditions, and electrical characteristics are identical for all product variants. Differences in the RF parameters are explained in the Radio specifications section. EMMY-W165-A UBX-16015271 - R03 Product Information Functional description Page 7 of 46 MAC/BB/RADIO2.4GHz WLAN TX2.4GHz WLAN RXBT RX/TXWLANANT5GHz WLAN TX/RX5GHz BPF &DIPLEXER2.4GHzBPFEMMY-W163SDIO37.4 MHzCrystalVIO1UARTVIO2PCMVIO2BT LTE COEXVIO2BT LEDWLAN LEDPDn2.4GHzBPFSP3T3.3VVIO1VIO2GNDNFCCOILBTANTVIO2GPIOsDC/DC3.3V1.8V1.1V EMMY-W1 series - User Manual 1.6 Supported features 1.6.1 Wi-Fi features Simultaneous client and access point operation (up to 10 clients supported) Support of Wi-Fi direct mode IEEE 802.11ac 1x1 antenna configuration IEEE 802.11 PHY data rates up to 433 Mbps Wi-Fi standards: IEEE 802.11a/b/g/n/ac/d/e/h/i/k2/r/v2/w 64- and 128-bit AES hardware encryption engine WAPI encryption is supported by hardware SDIO 3.0 host interface for Wi-Fi 1.6.2 Bluetooth features Bluetooth v4.2 with Bluetooth Low Energy and Classic Bluetooth v2.1+EDR over SDIO or high-speed UART interface PCM interface for audio MWS/LTE coexistence serial transport interface for connecting an external and co-located LTE device3 1.6.3 NFC features NCI 1.0 support according to NFC Forum specification NFC support through SDIO or UART Full protocol support for ISO 14443A/B, ISO 156934, ISO 18092, NFCIP-2, NFC forum, EMV contactless targets with data rates up to 848 Kbps Proprietary Low-Power Target Detection mode to reduce standby current consumption Deep Sleep On-Host card emulation: supported in NFC A, B, F and V technologies Off-Host card emulation with UICCs and Embedded SEs (availability is package dependent):

o ETSI TS 102 613: SWP/CLT ISO14443 Type A (Mifare) and ISO18093 212/424 kbps passive mode (FeliCa). o ETSI TS 102 622: SWP/HCI ISO14443A/B and ISO18092 212/424 kbps passive mode o DCLB Compliant with EMVCo book D (Contactless Communication Protocol) Reader/Writer, card emulation, and Peer-to-peer (P2P) modes Programmable carrier detection level for card emulation mode Programmable field detection level for RF anti-collision when operating as reader or active target UART host interface support (shared with Bluetooth when operating) 1.6.4 General product features Low-power and sleep modes for Bluetooth and Wi-Fi core Driver support for Linux Coexistence arbitration for Wi-Fi/Bluetooth/LE/NFC/LTE operation Automotive qualification tests (climatic, mechanical, and operating life tests) according ISO 16750-4 Small footprint (19.8 mm x 13.8 mm), LGA package Product variant with integrated LTE co-location filter available planned 2 Supported by hardware but not supported by firmware currently. 3 Available on request 4 For ISO 15693 VICC mode, the maximum supported 10-90% rise/fall times for receiving 10% ASK modulation is 1.18 s. UBX-16015271 - R03 Product Information Functional description Page 8 of 46 EMMY-W1 series - User Manual 1.6.5 Compliance RoHS compliant Radio type approvals for Europe, USA, Canada, Japan, Korea, Taiwan, China and Australia5 1.7 Additional reserved MAC addresses The EMMY-W1 module series has four unique consecutive MAC addresses reserved for each module, from which the first two addresses are already stored in the configuration during production. The first address is used for the Bluetooth communication while the second address is configured for Wi-Fi communication. The Data Matrix Code on the label includes the Bluetooth MAC address (see section 9). The remaining two MAC addresses are not used in the manufacturing configuration, but are reserved for usage with the module. MAC address Module1, address 1 Module1, address 2 Module1, address 3 Module1, address 4 Module2, address 1 Module2, address 2 Module2, address 3 Module2, address 4 Assignment Bluetooth Wi-Fi

(free for use)

(free for use) Bluetooth Wi-Fi

(free for use)

(free for use) Table 2: MAC address assignment Last two bits of MAC address Example 0b00 0b01 0b10 0b11 0b00 0b01 0b10 0b11 D4:CA:6E:44:00:04 D4:CA:6E:44:00:05 D4:CA:6E:44:00:06 D4:CA:6E:44:00:07 D4:CA:6E:44:00:08 D4:CA:6E:44:00:09 D4:CA:6E:44:00:0A D4:CA:6E:44:00:0B 5 Approvals are pending. UBX-16015271 - R03 Product Information Functional description Page 9 of 46 EMMY-W1 series - User Manual 2 Interfaces 2.1 Operation mode configuration EMMY-W1 series module uses the GPIO_3 and GPIO_2 pins as host interface configuration input to set the desired operation mode following a reset. The definitions of these pins are changed to their usual functions after reset. When you need to configure the pins for a certain module operation mode, you need to provide a 100 k pull down resistor to the ground. No external circuitry is required to set a configuration pin to high logical level. External reset is not needed for proper operation due to internal power-up reset logic though it can be used by the host controller through the PDn pin (active low) in case of an abnormal module behavior. After reset, GPIO_3 and GPIO_2 pins can be used as open drain outputs (depending on firmware/driver version) for Bluetooth and Wi-Fi activity LED indicators, but simultaneous usage of an LED connected to 3.3 V power line and a pull-down resistor is not allowed (LED acts as a strong pull-up circuitry). Do not connect LED if you need the pull-down resistors. Depending on the firmware or driver used, you can use either one or both host interface operation modes:

GPIO_3 GPIO_2 0 0 1 1 0 1 0 1 Wi-Fi SDIO SDIO SDIO SDIO Bluetooth/NFC Number of SDIO functions UART SDIO UART SDIO 1 (Wi-Fi) 3 (Wi-Fi, Bluetooth and NFC) 1 (Wi-Fi) 3 (Wi-Fi, Bluetooth and NFC)6 Table 3: Module configuration 2.2 SDIO interface EMMY-W1 series modules support an SDIO device interface that conforms to the industry standard SDIO 3.0 Full-Speed specification (4-bit SDIO up to 208 MHz) and allows a host controller using the SDIO bus protocol to access the Wi-Fi and Bluetooth functions. The interface supports 4-bit SDIO transfer mode at the full clock range of 0 to 208 MHz. 2.2.1 Default speed and High speed modes Figure 3: SDIO protocol timing diagram- Default speed mode (3.3 V) 6 Default configuration. It is possible to use connected LEDs to both the pins. UBX-16015271 - R03 Product Information Interfaces Page 10 of 46 EMMY-W1 series - User Manual Figure 4: SDIO protocol timing diagram High speed mode (3.3 V) Symbol Parameter fPP TWL TWH TISU TIH TODLY(max) TODLY(min) TODLY Clock frequency Clock low time Clock high time Input setup time Input hold time Maximal Output delay time Minimal Output delay time Output delay time CL 40 pF

(1 card) Condition Normal High speed Normal High speed Normal High speed Normal High speed Normal High speed Normal Normal Normal 0 0 10 7 10 7 5 6 5 2 TOH Output hold time High speed 2.5 Table 4: SDIO timing data Default speed, High speed modes (3.3 V) Min. Typ Max.

-

-

-

-

-

-

-

-

-

-

-

-

-

-

25 50

-

-

-

-

-

-

-

-

14 0 14

-

2.2.2 SDR12, SDR25, SDR50 Modes (up to 100 MHz) (1.8 V) Units MHz MHz ns ns ns ns ns ns ns ns ns ns ns ns Figure 5: SDIO protocol timing diagram SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8 V) UBX-16015271 - R03 Product Information Interfaces Page 11 of 46 Symbol Parameter Min. Typ fPP TIS TIH TCLK TCR, TCF, TODLY TOH Clock frequency Input setup time Input hold time Clock time Rise time, fall time TCR, TCF < 2 ns (max) at 100 MHz CCARD = 10 pF Output delay time CL 30 pF Output hold time CL = 15 pF Condition SDR12/25/50 SDR12/25/50 SDR12/25/50 SDR12/25/50 SDR12/25/50 SDR12/25/50 25 3 0.8 10 SDR12/25/50 1.5 EMMY-W1 series - User Manual Max. 100

-

-

40 0.2*TCLK 7.5

-

Units MHz ns ns ns ns ns ns

-

-

-

-

-

-

-

Table 5: SDIO timing data SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8 V) 2.2.3 SDR104 Mode (208 MHz) (1.8 V) Figure 6: SDIO protocol timing diagram SDR104 mode (208 MHz) Symbol Parameter Condition Min. Typ fPP TIS TIH TCLK TCR, TCF, TOP TODW Clock frequency Input setup time Input hold time Clock time Rise time, fall time TCR, TCF < 0.96 ns (max) at 208 MHz CCARD = 10 pF Card output phase Output timing of variable data window SDR104 SDR104 SDR104 SDR104 SDR104 0 1.4 0.8 4.8 SDR104 SDR104 0 2.88

-

-

-

-

-

-

-

Table 6: SDIO timing data SDR104 mode (208 MHz) Units MHz ns ns ns ns ns ns Max. 208

-

-

-

0.2*TCLK 10

-

UBX-16015271 - R03 Product Information Interfaces Page 12 of 46 2.2.4 DDR50 Mode (50 MHz) (1.8 V) EMMY-W1 series - User Manual Figure 7: SDIO CMD timing diagram DDR50 mode (50 MHz) Figure 8: SDIO DAT[3:0] timing diagram DDR50 mode (50 MHz) UBX-16015271 - R03 Product Information Interfaces Page 13 of 46 EMMY-W1 series - User Manual Symbol Parameter Condition Min. Typ Max. Units Clock TCLK TCR, TCF, Clock time 50 MHz (max) between rising edges Rise time, fall time TCR, TCF < 4.00 ns (max) at 50 MHz CCARD = 10 pF Clock Duty CMD Input (referenced to clock rising edge) TIS TIH Input setup time CCARD 10 pF (1 card) Input hold time CCARD 10 pF (1 card) DDR50 DDR50 DDR50 DDR50 20 45 6 DDR50 0.8 CMD Output (referenced to clock rising edge) TODLY TOHLD Output delay time during data transfer mode CL 30 pF (1 card) DDR50 Output hold time CL 15 pF (1 card) DDR50 1.5 DAT[3:0] Input (referenced to clock rising and falling edges) TIS2x TIH2x Input setup time CCARD 10 pF (1 card) Input hold time CCARD 10 pF (1 card) DDR50 3 DDR50 0.8 DAT[3:0] Output (referenced to clock rising and falling edges) TODLY2x (max) TODLY2x (min) Output delay time during data transfer mode CL 25 pF (1 card) DDR50 Output hold time CL 15 pF (1 card) DDR50 1.5 Table 7: SDIO timing data DDR50 mode (50 MHz) 2.3 High Speed UART interface 0.2*TCLK 55 13.7 7.0 ns ns

%

ns ns ns ns ns ns ns ns The EMMY-W1 series modules support a high speed Universal Asynchronous Receiver/Transmitter (UART) interface in compliance with the industry standard 16550 specification. The main features of the UART interface are:

FIFO mode permanently selected for transmit and receive operations 2 pins for transmit and receive operations 2 flow control pins High throughput (4 Mbps) Interrupt triggers for low-power, high throughput operation The UART interface operation includes:

Uploading the firmware to the module Supporting data input/output operation for peripheral devices connected through a standard UART interface Baud Rate 1200 2400 4800 9600 19200 38400 57600 76800 115200 230400 Table 8: Supported UART Baud rates 460800 500000 921600 1000000 1382400 1500000 1843200 2000000 2100000 2764800 3000000 3250000 3692300 4000000 UBX-16015271 - R03 Product Information Interfaces Page 14 of 46 2.4 PCM interface The EMMY-W1 series modules support a Pulse Code Modulation (PCM) interface that provides:

EMMY-W1 series - User Manual PCM bit width size of 8 bits or 16 bits Master or slave mode Up to 4 slots with configurable bit width and start positions Short frame and long frame synchronization 2.4.1 PCM interface specifications Figure 9: PCM timing specification Master mode Symbol FBCLK Duty Cycle BCLK TBCLK rise/fall TDO TDISU TDIHO TBF Parameter Condition Min. Typ Max.

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

0.4

-

-

20 15

-

2/2.048 0.5 3

-

-

-

-

-

0.6

-

15

-

-

15 Units MHz

-

Ns ns ns ns ns Table 9: PCM timing specification Master mode UBX-16015271 - R03 Product Information Interfaces Page 15 of 46 EMMY-W1 series - User Manual Figure 10: PCM timing specification Slave mode Symbol FBCLK Duty Cycle BCLK TBCLK rise/fall TDO TDISU TDIHO TBFSU TBFHO Parameter Condition Min. Typ Max.

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

0.4

-

-

15 10 15 10 2/2.048 0.5 3

-

-

-

-

-

-

0.6

-

30

-

-

-

-

Units MHz

-

ns ns ns ns ns ns Table 10: PCM timing specification Slave mode 2.5 GPIO interface The General-Purpose I/O (GPIO) interface is used to implement user defined input and output signals to and from the 88W8887 chip such as external interrupts and other user-defined I/Os. Main features of the GPIO interface include:

User-defined GPIO (each I/O configured to either input or output) Each GPIO independently controlled Each I/O configurable to output bit from GPIO_OUT The general functions associated with each GPIO pin is shown in Table 11:

UBX-16015271 - R03 Product Information Interfaces Page 16 of 46 EMMY-W1 series - User Manual GPIO Function General Input Output LEDs LED output7 Interrupts Input 0 X X

-

1 X X

-

X X 2 X X X X 3 X X X X 4 X X

-

5 X X

-

6 X X

-

7 X X

-

GPIOP Pin 8 9 10 11 12 13 14 15 16 17 X X

-

X X

-

X X

-

X X

-

X X

-

X X

-

X X

-

X X

-

X X

-

X X

-

X X X X X X X X X X X X X X Table 11: GPIO Functions GPIO [17:14], [12:0]

GPIO_12 is not available. 7 GPIO [2] is used for Wi-Fi activity while GPIO [3] is used for Bluetooth activity. UBX-16015271 - R03 Product Information Interfaces Page 17 of 46 EMMY-W1 series - User Manual 3 Pin Definition 3.1 Pin description Figure 11: Pin assignment No Pin name Pin type Supply domain Description 1 2 3 4 5 6 7 8 9 GND NC NC NC GPIO_0 GPIO_1 GPIO_14 GPIO_15 GPIO_16 10 GPIO_17 11 GPIO_4 12 GPIO_5 13 GPIO_6 14 GPIO_7 15 GND 16 GND 17 18 19 20 21 22 SD_CLK SD_CMD SD_D0 SD_D1 SD_D2 SD_D3 Ground I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Ground Ground I I/O I/O I/O I/O I/O

-

-

-

-

VIO2 VIO2 VIO2 VIO2 VIO2 VIO2 VIO2 VIO2 VIO2 VIO2

-

-

VIO1 VIO1 VIO1 VIO1 VIO1 VIO1 Ground Reserved, do not connect Reserved, do not connect Reserved, do not connect BT2HOST_WAKEUP (Output) WL2HOST_WAKEUP (Output) HOST2WL_WAKEUP (Input) HOST2BT_WAKEUP (Input) UART_LTE_SIN (Input) UART_LTE_SOUT (Output) PCM_DIN (Input) PCM_DOUT (Output) PCM_CLK (Input if slave, Output if master) PCM_SYNC (Input if slave, Output if master) Ground Ground SDIO Clock input SDIO Command line SDIO Data line bit [0]

SDIO Data line bit [1]

SDIO Data line bit [2]

SDIO Data line bit [3]

UBX-16015271 - R03 Product Information Pin Definition Page 18 of 46 GNDEMMY-W1SD_CLKSD_CMDSD_D0SD_D1SD_D2SD_D3GNDGND3V3VIO1VIO2PDnGPIO_8GPIO_9GPIO_1029303125262728244645444342414039GNDANT2GNDGNDGNDGNDANT1GND654321GNDReservedReservedReservedGPIO_0GPIO_17GPIO_148GPIO_159GPIO_1610GPIO_1711GPIO_412GPIO_513GPIO_614GPIO_715GND1617181920212223GPIO_1132GPIO_333GPIO_234GND35NFC_ANT_N36NFC_ANT_P37GND38 EMMY-W1 series - User Manual No Pin name Pin type Supply domain Description 23 GND 24 GND 25 26 27 28 3V3 VIO1 VIO2 PDn 29 GPIO_8 30 GPIO_9 31 GPIO_10 32 GPIO_11 33 GPIO_3 34 GPIO_2 Ground Ground Power Power Power Input I/O I/O I/O I/O I/O I/O

-

-

3.3V VIO1 VIO2

-

VIO2 VIO2 VIO2 VIO2 3.3V 3.3V Ground Ground 3.3V Power supply (2.97 V - 3.63 V) VIO1 Power supply (1.62V - 1.98 V, 2.97 V - 3.63 V) VIO2 Power supply (1.62V - 1.98 V, 2.97 V - 3.63 V) Full power down(active low)8 UART_SOUT (Output) UART_SIN (Input) UART_CTSn (Input) UART_RTSn (Output) LED_OUT_BT (Output) - BT indicator, Configuration pin9 LED_OUT_WLAN (Output) - WLAN indicator, Configuration pin9 35 GND Ground

-

Ground 36 37 NFC_ANT_N I/O, RF NFC_ANT_P I/O, RF 3.3V 3.3V NFC Coil Antenna, negative I/O pin NFC Coil Antenna, positive I/O pin 38 GND 39 GND 40 ANT2 41 GND 42 GND 43 GND 44 GND 45 ANT1 Ground Ground I/O, RF Ground Ground Ground Ground I/O, RF 46 GND Ground

-

Exposed pin Ground

-

-

-

-

-

-

-

-

-

-

Table 12: EMMY-W1 series pin description 3.2 Reset configuration Ground Ground Bluetooth antenna only in case of EMMY-W163 module. Not connected in case of EMMY-W161 or EMMY-W165 module10 Ground Ground Ground Ground Wi-Fi + Bluetooth antenna in case of single-antenna module. Wi-Fi antenna only in case of dual-antenna module10 Ground Six Ground/Thermal exposed pins, connect to the ground The EMMY-W1 is reset to its default operating state under the following conditions:

Power-on reset (POR) Module receives power 3V3 supplies rise (triggers internal POR circuit) Software/Firmware reset External pin assertion (PDn) will generate POR. 8 High input impedance pin for minimizing shutdown current consumption. The pin shall be driven by the host controller or/and connected via 51 k (or less) pull-up resistor to the 3.3 V supply rail. 9 Possible to use as an LED output depending on the firmware and driver version. In this case, the module pin acts as an open drain output and the whole LED circuitry must be supplied from 3.3 V power line. A LED current limiting resistor should be used; maximum sink current to the ground is 10 mA. These pins can also be used for host interface configuration. See Operation mode configuration section. 10 Pin protected from the static electricity by internal DC feed to the ground. UBX-16015271 - R03 Product Information Pin Definition Page 19 of 46 EMMY-W1 series - User Manual 4 Electrical specification Stressing the device above one or more of the ratings listed in the Absolute Maximum Rating section may cause permanent damage. These are stress ratings only. Operating the module at these or at any conditions other than those specified in the Operating conditions section

(section 4.2) of the specification should be avoided. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Operating condition ranges define those limits within which the functionality of the device is guaranteed. Where application information is given, it is advisory only and does not form part of the specification. 4.1 Absolute maximum ratings Symbol Description 3V3 VIO1 VIO2 TSTORAGE Power supply voltage 3.3 V I/O supply voltage 1.8 V I/O supply voltage 3.3 V I/O supply voltage 1.8 V I/O supply voltage 3.3 V Storage temperature Table 13: Absolute maximum ratings Min.

-

-

-40 Typ 3.3 1.8 3.3 1.8 3.3 Max. Units 4.0 2.2 4.0 2.2 4.0

+85 V V V V V C The product is not protected against overvoltage or reversed voltages. If necessary, voltage spikes exceeding the power supply voltage specification given in table above must be limited to values within the specified boundaries by using appropriate protection devices. 4.2 Operating conditions Symbol Parameter 3V3 VIO1 VIO2 Power supply voltage 3.3 V I/O supply voltage 1.8V/3.3 V I/O supply voltage 1.8V/3.3 V VDD_NFC NFC antenna input voltage (pins NFC_ANT_P/N) IANT_NFC NFC antenna peak input current (pins NFC_ANT_P/N)) TA Ripple Noise Ambient operating temperature Peak-to-peak voltage ripple on 3V3, VIO1 or VIO2 supply line. The values have been determined in a frequency range from 10 KHz to > 2 MHz [3]. Min. 2.97 1.62 2.97 1.62 2.97

-

-

-40 20 Typ 3.3 1.8 3.3 1.8 3.3

-

-

-

-

Max. 3.63 1.98 3.63 1.98 3.63 3.6 400

+85 Units V V V V V V mA C mV Table 14: Operating conditions Parameter Storage temperature Operation temperature Table 15: Temperature range Min.

-40

-40 Typ Max.

+85

+85 Units C C UBX-16015271 - R03 Product Information Electrical specification Page 20 of 46 4.3 Digital pin ratings Symbol Parameter VIH VIL VHYS VOH VOH Input high voltage Input low voltage Input hysteresis Output high voltage Output low voltage Table 16: Digital pin ratings for VIO1 and VIO2 supply domains 4.4 Wi-Fi power consumption Operation mode:

2.4 GHz Wi-Fi TX/RX with BT and NFC in Deep Sleep mode RX Idle Default RX 11 Mbps TX 11 Mbps (Normal power mode, 18 dBm) TX 11 Mbps (Low power mode, 10 dBm) RX 54 Mbps TX 54 Mbps (15 dBm) TX 54 Mbps (8 dBm) RX 11n MCS7 (HT20) TX 11n MCS7 (HT20, 15 dBm) TX 11n MCS7 (HT20, 8 dBm) EMMY-W1 series - User Manual Min. 0.7*VIO

-0.4 100 VIO-0.4

-

Max. VIO+0.4 0.3*VIO

-

-

0.4 Units V V mV V V Average current, mA11 Peak current, mA12 52 50 290 184 54 260 170 65 260 174 64 62 420 68 320 Operation mode:

5 GHz Wi-Fi TX/RX with BT and NFC in Deep Sleep mode Average current, mA11 Peak current, mA12 RX 54 Mbps TX 54 Mbps (12 dBm) TX 54 Mbps (8 dBm) RX MCS7 (HT20) TX MCS7 (HT20, 12 dBm) TX MCS7 (HT20, 8 dBm) RX MCS7 (HT40) TX MCS7 (HT40, 10 dBm) TX MCS7 (HT40, 8 dBm) RX MCS7 (VHT80) TX MCS7 (VHT80, 11 dBm) RX MCS8 (VHT20) TX MCS8 (VHT20, 11 dBm) RX MCS8 (VHT40) TX MCS8 (VHT40, 10 dBm) RX MCS8 (VHT80) TX MCS8 (VHT80, 8 dBm) RX MCS9 (VHT40) TX MCS9 (VHT40, 10 dBm) RX MCS9 (VHT80) TX MCS9 (VHT80, 8 dBm) 67 280 196 78 282 202 89 270 214 112 360 82 265 105 265 114 356 104 263 120 348 75 320 11 Supply 3.3V. Wi-Fi client mode. Numbers obtained from IPERF UDP traffic. 12 Maximum peak current for the worst supply conditions UBX-16015271 - R03 Product Information Electrical specification Page 21 of 46 EMMY-W1 series - User Manual Operation mode:

Power save modes Power Down WiFi and BT both in Deepsleep WiFi DTIM 1 and BT Deepsleep WiFi DTIM 3 and BT Deepsleep WiFi DTIM 5 and BT Deepsleep Table 17: Wi-Fi power consumption 4.5 Bluetooth power consumption Bluetooth mode with Wi-Fi and NFC in deep sleep mode TX @ 0dBm Average current, mA 0.03 0.13 1.14 0.47 0.34 Average current, mA13 Deep Sleep Mode BT idle (Sleep Mode) Power Down SCO HV3 Peak TX SCO HV3 Peak RX HV3 SCO mode ACL sniff 0x800 eSCO link, Master (2-EV3), ACL sniff 0x800 eSCO link, Master (EV3), ACL sniff 0x800 ACL (data pump) DH1 ACL (data pump) DH3 ACL (data pump) DH5 ACL Link, master sniff mode, interval=1.28s (800) ACL Link, master sniff mode, interval=500ms (320) SCO HV3 Average TX @ 4 dBm (external antenna) SCO HV3 Average RX @ 4 dBm (external antenna) Interlaced scan (= P&I scan) Page & Inquiry scan Page Scan Inquiry Scan LE Advertise @ 1.28s interval Peak LE TX Peak LE RX LE Link (interval=400=1.28s) LE Link (interval=320=1.00s) LE Scan (interval=800=1.28s) LE Scan (interval=640-1.00s) Table 18: Bluetooth power consumption 4.6 NFC power consumption Operation Mode TAG Type 1 TAG Type 2 TAG Type 3 TAG Type 4A Table 19: NFC power consumption 0.125 4.23 0.03 18.75 16.50 7.57 6.57 7.69 11.60 14.60 16.40 0.186 0.278 7.83 22.00 0.372 0.372 0.257 0.257 0.150 18.00 16.00 0.154 0.155 0.231 0.262 Average current, mA 3V3 90 95 85 100 13 Supply 3.3V, Average consumption current if not specified otherwise. UBX-16015271 - R03 Product Information Electrical specification Page 22 of 46 EMMY-W1 series - User Manual 4.7 Radio specifications 4.7.1 Wi-Fi The EMMY-W1 series modules support Wi-Fi standards IEEE 802.11a/b/g/n/ac in 2.4 GHz and 5 GHz radio bands. In the 2.4 GHz band, the EMMY-W1 supports 802.11b/g/n while in 5 GHz band, it supports 802.11a/n/ac. Parameter Operation Mode RF Frequency range Modulation Supported data rates Supported channel bandwidth Supported guard interval (GI) Maximum transmit power 802.11b/g/n 802.11a/n/ac 802.11b 802.11a/g/n/ac 802.11b 802.11a/g 802.11n 802.11ac 802.11ac 802.11n 802.11ac 802.11b 802.11a/g/n/ac Receiver sensitivity 2.4 GHz 802.11b 802.11g 802.11n 5 GHz 802.11a 802.11n 802.11ac 1 Mbps 11 Mbps 20 MHz 40 MHz 20 MHz 40 MHz 80 MHz 6 Mbps 54 Mbps MCS0 MCS7 MCS0 MCS7 6 Mbps 54 Mbps MCS0 MCS7 MCS0 MCS9 MCS0 MCS9 Specification 2.400 2.500 GHz 5.150 5.850 GHz CCK and DSSS OFDM 1, 2, 5.5, 11 Mbps 6, 9, 12, 18, 24, 36, 48, 54 Mbps MCS0 - MCS7 (150 Mbps) MCS0 MCS9 (433 Mbps) 20, 40, 80 MHz 400, 800 ms Short guard interval supported 18 dBm 1.5 dB 16 dBm 1.5 dB

-98 dBm 1 dB

-89 dBm 1 dB

-91 dBm 1 dB

-74 dBm 1 dB

-91 dBm 1 dB

-73 dBm 1 dB

-89 dBm 1 dB

-71 dBm 1 dB

-91 dBm 1 dB

-74 dBm 1 dB

-90 dBm 1 dB

-72 dBm 1 dB

-88 dBm 1 dB

-63 dBm 1 dB

-85 dBm 1 dB

-60 dBm 1 dB Table 20: Wi-Fi radio specifications Channel 1 Frequency, GHz 2.412 2 3 4 5 2.417 2.422 2.427 2.432 Channel 6 Frequency, GHz 2.437 7 8 9 10 2.442 2.447 2.452 2.457 Table 21: 2.4 GHz Band Supported Channels, 20 MHz bandwidth Channel Frequency, GHz 1 - 5 2 - 6 3 - 7 2.422 2.427 2.432 Channel Frequency, GHz 4 - 8 5 - 9 6 - 10 2.437 2.442 2.447 Table 22: 2.4 GHz band supported channels, 40 MHz bandwidth Channel 11 Frequency, GHz 2.462 12 13 2.467 2.472 Channel 7 - 11 Frequency, GHz 2.452 UBX-16015271 - R03 Product Information Electrical specification Page 23 of 46 EMMY-W1 series - User Manual Channel Frequency, GHz 36 40 44 48 52 56 60 64 5.180 5.200 5.220 5.240 5.260 5.280 5.300 5.320 Channel Frequency, GHz 100 104 108 112 116 132 136 140 5.500 5.520 5.540 5.560 5.580 5.660 5.680 5.700 Table 23: 5 GHz band supported channels, 20 MHz bandwidth Channel Frequency, GHz 36 - 40 44 - 48 52 - 56 60 - 64 5.190 5.230 5.270 5.310 Channel 100 - 104 108 - 112 132 - 136 140 - 144 Frequency, GHz 5.510 5.550 5.670 5.710 Table 24: 5 GHz band supported channels, 40 MHz bandwidth Channel Frequency, GHz 42 58 5.210 5.290 Channel Frequency, GHz 106 138 5.530 5.690 Table 25: 5 GHz band supported channels, 80 MHz bandwidth Channel Frequency, GHz 144 149 153 157 161 165 5.720 5.745 5.765 5.785 5.805 5.825 Channel 149 - 153 157 - 161 Frequency, GHz 5.755 5.795 Channel Frequency, GHz 155 5.775 The module is certified to operate as both client and master on channels 1 - 13 (2412 - 2462 MHz), and channel 36 48 (5180 5240 MHz). On the following channels it is certified to operate as a client only 52 64 (5260 5320 MHz), 100 116 (5500 5580 MHz), 132 140 (5660 5700 MHz) and 149 165 (5745 5825 MHz). When the module is set to operate on channels 52 64, 100 116, 132 140 and 149 165 it is restricted to only operate using passive scan. The module is certified to operate with the power tables shown in Table 26 for operation in the 2.4 GHz band and from Table 27 to Table 29 for operation in the 5 GHz band. The specified values are the maximum permitted output power settings. UBX-16015271 - R03 Product Information Electrical specification Page 24 of 46 Channel 1-11 12 13 1 2-9 10 11 12 13 1-11 12-13 1 2 3-10 11 12-13 1-10 11 12-13 EMMY-W1 series - User Manual Modulation Channel bandwidth Data rates Maximum power setting CCK and DSSS CCK and DSSS CCK and DSSS 1, 2, 5.5, 11 Mbps 1, 2, 5.5, 11 Mbps 1, 2, 5.5, 11 Mbps 18 dBm 15 dBm 13 dBm (EMMY-W161), 12 dBm (EMMY-W163) OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 6, 9, 12, 18, 24, 36 Mbps 13 dBm 6, 9, 12, 18, 24, 36 Mbps 16 dBm 6, 9, 12, 18, 24, 36 Mbps 15 dBm 6, 9, 12, 18, 24, 36 Mbps 13 dBm 6, 9, 12, 18, 24, 36 Mbps 10 dBm 6, 9, 12, 18, 24, 36 Mbps 9 dBm (EMMY-W161), 8 dBm (EMMY-W163) 48, 54 Mbps 48, 54 Mbps HT20 MCS0-MCS4 HT20 MCS0-MCS4 HT20 MCS0-MCS4 HT20 MCS0-MCS4 HT20 MCS0-MCS4 HT20 MCS5-MCS7 HT20 MCS5-MCS7 HT20 MCS5-MCS7 13 dBm 9 dBm 13 dBm 15 dBm 16 dBm 12 dBm 9 dBm 13 dBm 12 dBm 9 dBm (EMMY-W161), 8 dBm (EMMY-W163) 11 dBm (EMMY-W161), 10 dBm (EMMY-W163) 3 (2.422 GHz), 4 (2.427 GHz) OFDM 40 MHz HT40 MCS0-MCS4 5 (2.432 GHz) OFDM 6 (2.437 GHz), 7 (2.442 GHz) OFDM 8 (2.447 GHz) 9 (2.452 GHz) OFDM OFDM 3 (2.422 GHz), 4 (2.427 GHz) OFDM 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz HT40 MCS0-MCS4 HT40 MCS0-MCS4 HT40 MCS0-MCS4 HT40 MCS0-MCS4 HT40 MCS5-MCS7 13 dBm 14 dBm 13 dBm 10 dBm 11 dBm 5 (2.432 GHz), 6 (2.437 GHz), 7 (2.442 GHz), 8 (2.447 GHz) OFDM 40 MHz HT40 MCS5-MCS7 13 dBm 9 (2.452 GHz) OFDM 40 MHz HT40 MCS5-MCS7 11 dBm Table 26: WLAN power table for operation in the 2.4 GHz band UBX-16015271 - R03 Product Information Electrical specification Page 25 of 46 EMMY-W1 series - User Manual Modulation Channel bandwidth Data rates Maximum power setting 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 6, 9, 12, 18, 24, 36 Mbps 13 dBm 6, 9, 12, 18, 24, 36 Mbps 16 dBm 48, 54 Mbps 13 dBm HT20 MCS0-MCS4 13 dBm HT20 MCS0-MCS4 16 dBm HT20 MCS5-MCS7 13 dBm VHT20 MCS0-MCS4 13 dBm VHT20 MCS0-MCS4 16 dBm VHT20 MCS5-MCS8 13 dBm HT40 MCS0-MCS4 12 dBm HT40 MCS0-MCS4 16 dBm HT40 MCS5-MCS7 12 dBm (ELLA-W161), 11 dBm (ELLA-W163) VHT40 MCS0-MCS4 12 dBm VHT40 MCS0-MCS4 16 dBm VHT40 MCS5-MCS7 12 dBm 38 (5.190 GHz), 46 (5.230 GHz), 54 (5.270 GHz) , 62 (5.310 GHz) OFDM 40 MHz VHT40 MCS8-MCS9 10 dBm 42 (5.210 GHz), 58 (5.290 GHz) OFDM 80 MHz VHT80 MCS0-MCS9 8 dBm Table 27: WLAN power table for operation in the 5 GHz U-NII-1 and U-NII-2A bands Modulation Channel bandwidth Data rates Maximum power setting Channel 36, 64 40, 44, 48, 52, 56, 60 OFDM OFDM 36, 40, 44, 48, 52, 56, 60, 64 OFDM 36, 64 40, 44, 48, 52, 56, 60 OFDM OFDM 36, 40, 44, 48, 52, 56, 60, 64 OFDM 36, 64 40, 44, 48, 52, 56, 60 OFDM OFDM 36, 40, 44, 48, 52, 56, 60, 64 OFDM 38 (5.190 GHz), 62 (5.310 GHz) OFDM 46 (5.230 GHz), 54 (5.270 GHz) OFDM 38 (5.190 GHz), 46 (5.230 GHz), 54 (5.270 GHz) , 62 (5.310 GHz) OFDM 38 (5.190 GHz), 62 (5.310 GHz) OFDM 46 (5.230 GHz), 54 (5.270 GHz) OFDM 38 (5.190 GHz), 46 (5.230 GHz), 54 (5.270 GHz) , 62 (5.310 GHz) OFDM Channel 100, 140 104-136 (exc. 120-128) 100-140 (exc. 120-128) 100, 140 104-136 (exc. 120-128) 100-140 (exc. 120-128) 100 104-144 (exc. 120-128) 100-144 (exc. 120-128) OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM 102 (5.510 GHz), 134 (5.670 GHz) OFDM 110 (5.550 GHz) 102 (5.510 GHz), 110 (5.550 GHz) 134 (5.670 GHz) 102 (5.510 GHz) OFDM OFDM OFDM 110 (5.550 GHz), 134 (5.670 GHz), OFDM 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 6, 9, 12, 18, 24, 36 Mbps 13 dBm 6, 9, 12, 18, 24, 36 Mbps 16 dBm 48, 54 Mbps 13 dBm HT20 MCS0-MCS4 13 dBm HT20 MCS0-MCS4 16 dBm HT20 MCS5-MCS7 13 dBm VHT20 MCS0-MCS4 13 dBm VHT20 MCS0-MCS4 16 dBm VHT20 MCS5-MCS8 13 dBm HT40 MCS0-MCS4 12 dBm HT40 MCS0-MCS4 16 dBm HT40 MCS5-MCS7 12 dBm VHT40 MCS0-MCS4 12 dBm VHT40 MCS0-MCS4 16 dBm UBX-16015271 - R03 Product Information Electrical specification Page 26 of 46 EMMY-W1 series - User Manual Channel 142 (5.710 GHz) Modulation Channel bandwidth Data rates Maximum power setting 102 (5.510 GHz), 110 (5.550 GHz), 134 (5.670 GHz), 142 (5.710 GHz) OFDM 102 (5.510 GHz), 110 (5.550 GHz), 134 (5.670 GHz), 142 (5.710 GHz) OFDM 40 MHz VHT40 MCS5-MCS7 12 dBm 40 MHz VHT40 MCS8-MCS9 10 dBm 106 (5.530 GHz) 138 (5.690 GHz) 138 (5.690 GHz) 138 (5.690 GHz) 138 (5.690 GHz) OFDM OFDM OFDM OFDM OFDM 80 MHz 80 MHz 80 MHz 80 MHz 80 MHz VHT80 MCS0-MCS9 8 dBm VHT80 MCS0-MCS2 16 dBm VHT80 MCS3-MCS4 13 dBm VHT80 MCS5-MCS7 10 dBm VHT80 MCS8-MCS9 8 dBm Table 28: WLAN power table for operation in the 5 GHz U-NII-2e band Modulation Channel bandwidth Data rates Maximum power setting Channel 149, 165 153, 157, 161 149-165 149, 165 153, 157, 161 149-165 149 153, 157, 161, 165 149-165 151 (5.755 GHz) 159 (5.795 GHz) OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM OFDM 151 (5.755 GHz), 159 (5.795 GHz) OFDM 151 (5.755 GHz), 159 (5.795 GHz) OFDM 155 (5.775 GHz) OFDM 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 40 MHz 40 MHz 40 MHz 40 MHz 80 MHz 6, 9, 12, 18, 24, 36 Mbps 14 dBm 6, 9, 12, 18, 24, 36 Mbps 16 dBm 48, 54 Mbps 13 dBm HT20 MCS0-MCS4 13 dBm HT20 MCS0-MCS4 16 dBm HT20 MCS5-MCS7 13 dBm VHT20 MCS0-MCS4 13 dBm VHT20 MCS0-MCS4 16 dBm VHT20 MCS5-MCS8 13 dBm HT40 MCS0-MCS4 12 dBm HT40 MCS0-MCS4 16 dBm HT40 MCS5-MCS7 12 dBm VHT40 MCS0-MCS9 12 dBm VHT80 MCS0-MCS9 8 dBm Table 29: WLAN power table for operation in the 5 GHz U-NII-3 band UBX-16015271 - R03 Product Information Electrical specification Page 27 of 46 EMMY-W1 series - User Manual 4.7.2 Bluetooth Parameter RF Frequency Range Supported Modes Number of channels Modulation Transmit Power Receiver Sensitivity Specifications 2.400 2.4835 GHz Bluetooth v4.2 (including Bluetooth Low Energy and Classic Bluetooth with BR and EDR) 79 1 Mbps: GFSK (BR) 2 Mbps: /4 DQPSK (EDR) 3 Mbps: 8DQPSK (EDR) Class 2, Class 1, BR: 10 dBm 2 dB, EDR: 8 dBm 2 dB14

-85 dBm Table 30: Bluetooth radio specifications 4.7.3 LTE co-existence Specific influence of BAW filters on the following RF parameters:

Wi-Fi output power Wi-Fi sensitivity Bluetooth output power Bluetooth sensitivity Characterization of LTE co-existence:

Maximum tolerated input power from LTE interferer Rejection in LTE bands Wi-Fi and Bluetooth desensitization in presence of LTE transmission in adjacent bands for given antenna isolation BAW decrease influence to LTE as well The BAW-Filter is included only in the EMMY-W161 module variant. 4.7.4 Near field communication 4.7.4.1 Card emulator specifications Parameter Condition AC characteristics Minimum Type Maximum Units VsensPICC MODPICC DRPICC Input carrier detection level, full-power mode, peak sinus differential voltage on NFC_ANT_P/N pin Input ASK modulation index15 Input data rate (coding depending on standard:

Manchester, Modified, Miller, or NRZ

-

8 106 300

-

-

-

100 848 mVpeak

%

Kbps Table 31: NFC card emulator For typical recommended operating conditions unless otherwise specified. 4.7.4.2 Reader/Writer specifications Parameter Condition Minimum Type Maximum Units DC characteristics VCMTX_PA Power amplifier output common mode level AC characteristics

-

VDDTX/2

-

V 14 For regulatory reasons in Europe only class 2 operations are permitted. 15 As defined in ISO/IEC 14443-2, for example, [a-b]/[a+b] where a and b are the peak and minimum signal amplitude respectively. UBX-16015271 - R03 Product Information Electrical specification Page 28 of 46 EMMY-W1 series - User Manual Parameter Condition Minimum Type Maximum Units FTXCARR ROUT_ANT MODPCD Output carrier frequency 13.553 13.56 13.567 Power amplifier output impedance Output ASK modulation index15

-

8 50

-

-

100 MHz

%

Table 32: NFC Reader/Writer specifications For typical recommended operating conditions unless otherwise specified. UBX-16015271 - R03 Product Information Electrical specification Page 29 of 46 EMMY-W1 series - User Manual 5 Host drivers and firmware 5.1 General principle The EMMY-W1 series module does not contain any persistent software. A firmware binary will be downloaded by the host operating system driver on system start-up. 5.2 Supported operating systems 5.2.1 Linux Linux device drivers are available from u-blox. Once you sign the Limited Use License Agreement (LULA) with u-blox, a driver package will be available. This package includes:

drivers will be provided. Dedicated Kernel driver, to bind the Wi-Fi, Bluetooth and NFC block to the kernel. The sources of those A dedicated firmware image, which will be uploaded during initialization. Various configuration tools Laboratory and manufacturing tools For a detailed description of the driver packages, refer to EMMY-W1 series System Integration Manual [3]. UBX-16015271 - R03 Product Information Host drivers and firmware Page 30 of 46 EMMY-W1 series - User Manual 6 Mechanical specifications Figure 12: Physical dimensions UBX-16015271 - R03 Product Information Mechanical specifications Page 31 of 46 EMMY-W1 series - User Manual 7 Qualification and approvals 7.1 Approvals16 Products marked with this lead-free symbol on the product label comply with the

"Directive 2002/95/EC of the European Parliament and the Council on the Restriction of Use of certain Hazardous Substances in Electrical and Electronic Equipment" (RoHS). EMMY-W1 series Wi-Fi modules are RoHS compliant. 7.1.1 European Union regulatory compliance The EMMY-W1 series module complies with the regulatory standards Effective use of spectrum:

EN 300 328 V 1.8.1 EN 301 893 V 1.7.1 EMC:

EN 301 489-1/-17 Health and safety:

EN 60950-1:2006 + A11:2009 EN 62311 (WLAN) EN 62479 (BT) We declare that the human exposure of these modules is below the SAR limits specified in the EU recommendations 1999/519/EC. 7.1.1.1 Equipment classes A multi-radio module is classified as class-1 or class-2 radio equipment depending on the frequency band in which it can operate. This equipment class is inherited by the end-product that integrates the module, thus it must be marked accordingly. Class-1 radio equipment can be placed on the market and put into service without restrictions.

(Article 1 of Commission Decision 2000/299/EC of April 6 2000) This multi-radio module is defined as class-1 radio equipment when it is restricted to operate in the following frequency bands:

Bluetooth , ISM band 2400 2483.5 MHz WLAN, ISM band 2400 2483.5 MHz WLAN, U-NII band-2e 5470 5725 MHz Class-2 radio equipment includes restrictions applied by Member States as indicated in Article 1(2) of the Commission Decision. This class uses the Alert Sign as an equipment class identifier. Figure 13: Alert sign to identify equipment Class-2 16 These approvals are pending. UBX-16015271 - R03 Product Information Qualification and approvals Page 32 of 46 EMMY-W1 series - User Manual If an end product allows the multiradio module to operate in the 5150-5350 MHz band (WLAN channel: 36-64), it is defined as class-2 radio equipment and must be marked accordingly. Class-2 radio equipment must have the

"alert" sign affixed on the equipment, packaging and printed in the user manual. The EMMY-W1 multiradio module uses harmonized frequency bands thus it is comprised by subclass H01 of class 2 equipment, for which notification in accordance with article 6(4) of the R&TTE directive is not necessary. A definition of subclasses of Class 2 equipment can be found in the following link:

http://ec.europa.eu/enterprise/sectors/rtte/files/rtte-subclass2_en.pdf The table below shows the restrictions when operating WLAN at different bands within the European countries Band Channel number ISM 1 11 U-NII 1 36 48 U-NII 2 52 64 Channel frequency

[MHz]

2412 2462 5180 5240 5260 5320 U-NII 2e 100 140 5500 5700 Indoor use allowed Outdoor use allowed Radio Equipment Class Yes Yes Yes Yes Yes No No Yes 1 2 2 1 Table 33: Operating restrictions and radio equipment classification of EMMY-W1 series Guidance on how the end product is marked in accordance with the R&TTE directive can be found in the following links:

http://ec.europa.eu/enterprise/sectors/rtte/documents/index_en.htm - h2-5 http://ec.europa.eu/enterprise/sectors/rtte/documents/guidance/index_en.htm A direct link to the quick guide to the marking requirements can be found here:

http://ec.europa.eu/enterprise/sectors/rtte/files/guidance/guidance_en.pdf IMPORTANT: The CE marking must be affixed to a visible location on the OEM product in which this module is installed and has to be labeled in accordance to R&TTE Directive 1999/5/EC. 7.1.2 FCC compliance The EMMY-W1 series module complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation Non authorized modification could void authority to use this equipment. The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. In accordance with 47 CFR 15.19, the end product into which this module is integrated shall bear the following statement in a conspicuous location on the device:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation UBX-16015271 - R03 Product Information Qualification and approvals Page 33 of 46 EMMY-W1 series - User Manual When the end-product is so small or for such use that it is not practical to place the above statement on it, the information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or on the container in which the device is marketed. However, the FCC ID label must be displayed on the device. If the end-product will be installed in locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual. The outside of final products containing the EMMY-W1 module must display in a user accessible area a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID: (XYZ)(UPN) or Contains FCC ID: (XYZ)(UPN), where (XYZ) represents the FCC Grantee Code and (UPN) is the Unique Product Number decided by the grant owner17. 7.1.3 IC compliance The EMMY-W1 series module complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Any notification to the end user of installation or removal instructions about the integrated radio module is NOT allowed. Unauthorized modification could void authority to use this equipment. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This radio transmitter IC: 8595A-EMMYW161, IC: 8595A-EMMYW163 and IC: 8595A-EMMYW165 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device; otherwise, the host device must be labeled to display the Industry Canada certification number for the module, preceded by the words Contains transmitter module, or the word Contains, or similar wording expressing the same meaning, as follows: Contains transmitter module IC: (CN)-(UPN), where (CN) is the Company Number registered at Industry Canada and (UPN) is the Unique Product Number decided by the grant owner. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Cet quipement est conforme aux limites d'exposition de rayonnement d'IC RSS-102 dtermines pour un environnement non contrl. Cet quipement devrait tre install et actionn avec la distance minimum 20 cm entre le radiateur et votre corps. Cet metteur radio, IC: 8595A-EMMYW161, IC: 8595A-EMMYW163 et IC: 8595A-EMMYW165 t approuv par Industry Canada pour fonctionner avec les types dantenne numrs ci-dessous avec le gain maximum 17 The FCC and IC IDs for the EMMY-W1 series module variants are shown in Table 37. Select the applicable ID. UBX-16015271 - R03 Product Information Qualification and approvals Page 34 of 46 EMMY-W1 series - User Manual autoris et limpdance ncessaire pour chaque type dantenne indiqu. Les types dantenne ne figurant pas dans cette liste et ayant un gain suprieur au gain maximum indiqu pour ce type-l sont strictement interdits dutilisation avec cet appareil. Le dispositif de fonctionnement dans la bande 5150-5250 MHz est rserv une utilisation en intrieur pour rduire le risque d'interfrences nuisibles la co-canal systmes mobiles par satellite Opration dans la bande 5600-5650 MHz n'est pas autorise au Canada. Haute puissance radars sont dsigns comme utilisateurs principaux (c.-utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-

5850 MHz et que ces radars pourraient causer des interfrences et / ou des dommages dispositifs LAN-

EL. Ltiquette dhomologation dIndustrie Canada dun module donn doit tre pose sur lappareil hte un endroit bien en vue en tout temps. En labsence dtiquette, lappareil hte doit porter une tiquette sur laquelle figure le numro dhomologation du module dIndustrie Canada, prcd des mots Contient un module dmission , ou du mot Contient , ou dune formulation similaire allant dans le mme sens et qui va comme suit : Contient le module dmission IC: (CN)-(UPN) , o (CN) reprsente le numro de compagnie, attribu par Industrie Canada et (UPN) reprsente le numro de produit unique attribu par le requrant. The approval of the variant EMMY-W165 with the IC: 8595A-EMMYW165 is still in progress and expected to be finished soon. The internal / external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. See Table 34 for list of approved antennas. The approval type for all the EMMY-W1 series variants is a limited modular approval. Due to Industry Canada Modular Approval Requirements (Source: RSP-100 Issue 10), any application which includes the module must be approved by the module manufacturer (u-blox). The application manufacturer must provide design data for the review procedure. 7.2 Approved antennas For Bluetooth and Wi-Fi operation in the 2.4 GHz band and Wi-Fi operation in the 5 GHz band, the module has been tested and approved for use with the antenna listed in Table 34. Manufacturer Part Number Antenna type Peak gain [dBi]

2.4 GHz band 5 GHz band Antenova A10194 SMD chip antenna 10x10x0.9 [mm] [4]

Linx Taoglas Taoglas Walsin Linx Delock ANT-DB1-RAF-RPS Dual-band dipole antenna [5]

GW.40.2153 Dual-band dipole antenna [6]

GW.59.3153 Dual-band dipole antenna [7]

RFDPA870900SBLB8G1 Dual-band dipole antenna [8]

ANT-2.4-CW-RCT-RP Single-band dipole antenna [9]

88395 Dual-band dipole antenna [10]

Table 34: List of approved dual-band antennas 1.8 2.5 3.74 2.37 2 2.2 1.5 4.1 4.6 2.5 2.93 3 N/A 2.1 The module can be integrated with other antennas which the OEM installer must authorize with respective regulatory agencies and after approval of the module manufacturer. UBX-16015271 - R03 Product Information Qualification and approvals Page 35 of 46 7.2.1 Bluetooth antenna The following antennas are designated for Bluetooth transmission on EMMY-W163:

EMMY-W1 series - User Manual Manufacturer Part Number Antenna type Peak gain [dBi]

2.4 GHz band Johanson Technology Taoglas Linx 2450AT45A100 SMD chip antenna 10x10x0.9 [mm] [11]

2.2 GW.26.0151 Single-band monopole antenna [12]

ANT-2.4-CW-RH Single-band monopole antenna [13]

0.0

-0.9 Table 35: List of approved single-band antennas 7.2.2 NFC antenna The following antennas are designated to be used for Near Field Communication (NFC) on EMMY-W161, EMMY-W163 and EMMY-W165:

Manufacturer Part Number Antenna type u-blox EMMY_NFC_ANT External PCB antenna with connector Table 36: List of approved NFC antenna 7.3 FCC and IC IDs (planned) Product name EMMY-W161 EMMY-W161-A EMMY-W163 EMMY-W163-A EMMY-W165 EMMY-W165-A FCC ID IC ID XPYEMMYW161 XPYEMMYW161 XPYEMMYW163 XPYEMMYW163 XPYEMMYW165 XPYEMMYW165 8595A-EMMYW161 8595A-EMMYW161 8595A-EMMYW163 8595A-EMMYW163 8595A-EMMYW165 8595A-EMMYW165 Table 37: FCC and IC IDs for different models of EMMY-W1 series 7.4 Certification in other countries Regulatory approvals for using the EMMY-W1 series module in Japan, South Korea, China, Taiwan and Australia are pending. UBX-16015271 - R03 Product Information Qualification and approvals Page 36 of 46 EMMY-W1 series - User Manual 8 Product handling 8.1 Packaging The EMMY-W1 series modules are delivered as hermetically sealed tape and reels, to enable efficient production, production lot set-up and tear-down. For more information about packaging, see the u-blox Package Information Guide [1]. 8.1.1 Reels The EMMY-W1 series modules are deliverable in quantities of 500 pieces on a reel. The EMMY-W1 series modules are shipped on reel Type A as described in the u-blox Package Information Guide [1]. 8.1.2 Tapes The dimensions of the tapes are specified in Figure 14. Figure 14: EMMY-W1 Tape dimensions 8.2 Shipment, storage and handling For more information regarding shipment, storage and handling see the u-blox Package Information Guide [1]. 8.2.1 Moisture sensitivity levels The EMMY-W1 series modules are rated at moisture sensitivity level 3. See moisture sensitive warning label on each shipping bag for detailed information. After opening the dry pack, modules must be mounted within 168 hours in factory conditions of maximum 30C/60%RH or must be stored at less than 10%RH. Modules require baking if the humidity indicator card shows more than 10% when read at 235C or if the conditions mentioned above are not met. Please refer to J-STD-033B standard for bake procedure. }

UBX-16015271 - R03 Product Information Product handling Page 37 of 46 EMMY-W1 series - User Manual 8.2.2 Mounting process and soldering recommendations The EMMY-W1 series module is a surface mount module supplied on a 4-layer FR4-type PCB with gold plated connection pins and produced in a lead-free process with a lead-free soldering paste. The wrap page of the PCB is max. 0,75% according to IPC-A-610E. The thickness of solder resist on the host PCB top side and the EMMY-W1 bottom side must be considered for the soldering process. This module is compatible with industrial reflow profile for RoHS/Pb-free solders, Sn96.5/Ag3.0/Cu0.5 solder is a right choice. Use of "No Clean" soldering paste is strongly recommended, cleaning the populated modules is strongly discouraged - residuals under the module cannot be easily removed with any cleaning process. Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pins. Only a single reflow soldering process is permitted for host boards with the EMMY-W1 series modules. The reflow profile used is dependent on the thermal mass of the entire populated PCB, heat transfer efficiency of the oven and particular type of solder paste used. Since the profile used is process and layout dependent, the optimum profile should be studied case by case. Recommendations below should be taken as a starting point guide. In case of basic information necessity, please refer to J-STD-020C standard. }

Profile feature Ramp up rate (TSMAX to TP) Minimum soak temperature (TSMIN) Maximum soak temperature (TSMAX) Soak time (ts) Liquidus temperature (TL) Time above TL (tL) Peak temperature (TP) Sn-Pb eutectic

(Sn63/Pb37) 3 C/sec max 100 C 150 C 60 - 120 sec 183 C 60 - 150 sec 215 225 C Time within +0 / -5C of actual TP (tp) 10 - 30 sec Ramp down rate Time from 25C to TP 6 C/sec max 6 min max Table 38: Recommended reflow profile RoHS/Pb-free

(Sn96.5/Ag3.0/Cu0.5) 3 C/sec max 150 C 200 C 60 - 180 sec 217 C 60 - 150 sec 235 245 C 20 - 40 sec 6 C/sec max 8 min max The lowest value of TP and slower ramp down rate (2 3 C/sec) is preferred. Figure 15: Reflow profile UBX-16015271 - R03 Product Information Product handling Page 38 of 46 EMMY-W1 series - User Manual 8.2.3 ESD handling precautions EMMY-W1 series modules are Electrostatic Sensitive Devices (ESD). Observe precautions for handling! Failure to observe these precautions can result in severe damage to the Wi-Fi receiver!

Wi-Fi transceivers are Electrostatic Sensitive Devices (ESD) and require special precautions when handling. Particular care must be exercised when handling patch antennas, due to the risk of electrostatic charges. In addition to standard ESD safety practices, the following measures should be taken into account whenever handling the receiver:

Unless there is a galvanic coupling between the local GND (i.e. the work table) and the PCB GND, then the first point of contact when handling the PCB must always be between the local GND and PCB GND. Before mounting an antenna patch, connect ground of the device When handling the RF pin, do not come into contact with any charged capacitors and be careful when contacting materials that can develop charges (e.g. patch antenna ~10 pF, coax cable ~50-80 pF/m, soldering iron, ) To prevent electrostatic discharge through the RF input, do not touch any exposed antenna area. If there is any risk that such exposed antenna area is touched in non ESD protected work area, implement proper ESD protection measures in the design. When soldering RF connectors and patch antennas to the receivers RF pin, make sure to use an ESD safe soldering iron (tip). UBX-16015271 - R03 Product Information Product handling Page 39 of 46 EMMY-W1 series - User Manual 9 Labeling and ordering information 9.1 Product labeling The labels of EMMY-W1 series include important product information as described in this section. The data matrix code for automotive and professional grade variants of EMMY-W1 series includes a serial number. Figure 16 illustrates the sample label of the automotive grade (professional grade is similar and differs with respect to product version (1) as mentioned in Table 39) of the EMMY-W1 series and includes: the u-blox logo, product name (model), type number, FCC and IC certification number and date of unit production encoded YY/WW (year/week). 1 2 3 4 5 Figure 16: EMMY-W1 series Professional grade sample label A detailed description of the label components are listed in Table 39. The first three digits of the serial number represent the Bluetooth MAC address. Reference Description 1 2 3 4 Text MODEL: followed by product type number, omitting the second dash and smaller font used for the product version identifier (xxB-yy for professional and xxA-yy for automotive grade). Date of production encoded YY/WW (year/week) FCC/IC ID which the module has been listed with Data Matrix with unique serial number of 15 alphanumeric symbols. The 3 first symbols represent the unique module type no:

631: EMMY-W161-00A-00, 632: EMMY-W163-00A-00, 700: EMMY-W163-00B-00, 701: EMMY-W161-00B-00, 756: EMMY-W165-00A-00,

???: EMMY-W165-00B-00,

, the next 8 symbols represent the unique hexadecimal Bluetooth MAC address (see section 1.7 for more information about MAC addresses) of the module AABBCCDDEE, and the last 4 symbols represent the hardware and firmware version encoded HHFF. 5 u-blox logo, the red dot in the logo is also marking pin no 1 Table 39 EMMY-W1 series label description UBX-16015271 - R03 Product Information Labeling and ordering information Page 40 of 46 EMMY-W1 series - User Manual 9.2 Explanation of codes Two different product code formats are used. The Product Name is used in documentation such as this data sheet and identifies all u-blox products, independent of packaging and quality grade. The Ordering Code includes options and quality, while the Type Number includes the hardware and firmware versions. Table 40 below details these three different formats:

Format Product Name Ordering Code Type Number Structure PPPP-TGVV PPPP-TGVV-TTQ PPPP-TGVV-TTQ-XX Table 40: Product code formats Table 41 explains the parts of the product code. Code Meaning PPPP TG VV TT Q Form factor Platform T Dominant technology, For example, W: Wi-Fi, B: Bluetooth G - Generation Variant based on the same platform; range [0099]

Major Product Version Quality grade A: Automotive B: Professional C: Standard XX Minor product version (not relevant for certification) Table 41: Part identification code 9.3 Ordering codes Example EMMY W1 61 00 A 00 Ordering Code Product name Product EMMY-W161-00B EMMY-W161 EMMY-W161 professional grade module EMMY-W161-00A EMMY-W161-A EMMY-W161 automotive grade module EMMY-W163-00B EMMY-W163 EMMY-W163 professional grade module EMMY-W163-00A EMMY-W163-A EMMY-W163 automotive grade module EMMY-W165-00B EMMY-W165 EMMY-W165 professional grade module EMMY-W165-00A EMMY-W165-A EMMY-W165 automotive grade module EVK-EMMY-W161-A EVK-EMMY-W161 Evaluation kit for EMMY-W161 and EMMY-W161-A EVK-EMMY-W163-A EVK-EMMY-W163 Evaluation kit for EMMY-W163 and EMMY-W163-A Table 42: Product ordering codes Product changes affecting form, fit or function are documented by u-blox. For a list of Product Change Notifications (PCNs) see our website. UBX-16015271 - R03 Product Information Labeling and ordering information Page 41 of 46 EMMY-W1 series - User Manual Appendix A Glossary Name ACL AES BPF BT BAW CPU DTIM DC DDR ESD EMV FCC FIFO GI GND GPIO HD HCI IC IMDS IMEI LED LTE LE MAC MWS MCS MSL NFC NFCIP OEM P2P PCB PCN PCM R&TTE RF RSS RH RoHS SDIO Definition Access control list Advanced Encryption Standard Band-Pass Filter Bluetooth Bulk Acoustic Wave Central Processing Unit Delivery traffic indication message Direct Current Double Data Rate Electrostatic Sensitive Devices Europay, MasterCard and Visa Federal Communications Commission First In, First Out Guard interval Ground General-purpose input/output High Definition Host Controller Interface Industry Canada International Material Data System International Mobile Station Equipment Identity Light-emitting diode Long Term Evolution Low Energy Medium Access Control Mobile Wireless Standards Modulation Coding Scheme Moisture sensitivity level Near-Field Communication NFC Interface and Protocol Original equipment manufacturer Peer-to-peer Printed Circuit Board Product Change Notification Pulse-code modulation Radio and telecommunications terminal equipment Radio Frequency Radio Standards Specification Relative humidity Restriction of Hazardous Substances Secure Digital Input Output UBX-16015271 - R03 Product Information Appendix Page 42 of 46 EMMY-W1 series - User Manual Name SDR SMD SCO UART Definition Secure Digital Rate Surface-mount Device Synchronous Connection-Oriented Universal Asynchronous Receiver/Transmitter Table 43: Explanation of abbreviations and terms used UBX-16015271 - R03 Product Information Appendix Page 43 of 46 EMMY-W1 series - User Manual Related documents

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

u-blox Package Information Guide, document number UBX-14001652 Driver Software Application Note for ELLA-W1 series and EMMY-W1 series, document number UBX-15012542 EMMY-W1 series System Integration Manual, document number UBX-15024929 Mixtus A10194 Product Specification, Antenova-M2M, http://www.antenova-

m2m.com/documents/download/40c67cf2e7a4c7b8cd0f7faed7f6d2ca4fe1886d597d5, October 2015 ANT-DB1-RAF-xxx Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-db1-

raf-xxx.pdf, October 2015 Specification. Part No.: GW.40.2153, taoglas, https://fccid.io/pdf.php?id=2415249, December 2015 Specification. Part No.: GW.59.3153, taoglas, http://www.taoglas.com/images/product_images/original_images/GW.59.3153- 2.4GHz-5.8GHz Band Mount Dipole Antenna 080910.pdf, October 2015 2015 RF Devices and High Frequency Inductors Product catalog, http://www.passivecomponent.com/document/HF_Devices/2013RF_Catalogue.pdf, December 2015 ANT-2.4-CW-RCT-xx Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-

2.4-cw-rct-xx.pdf, October 2015 Delock WLAN 802.11 ac/a/b/g/n Antenna RP-SMA 2 dBi Omnidirectional Joint, 2015-11-26 http://www.delock.com/produkt/88395/pdf.html?sprache=en, November 2015 2.45 GHz High Gain SMD Chip Antenna P/N 2450AT45A100, Johanson Technology, http://www.johansontechnology.com/datasheets/antennas/2450AT45A100.pdf, October 2015 2.4 GHz Miniature Screw mount Monopole Antenna, taoglas, http://www.taoglas.com/images/product_images/original_images/GW.26.0112 2.4GHz Band Monopole SMA%28M%29RA.pdf, December 2015 ANT-2.4-CW-RH Data Sheet, Linx, http://www.linxtechnologies.com/resources/data-guides/ant-2.4-cw-

rh-xxx.pdf, December 2015 For regular updates to u-blox documentation and to receive product change notifications, register on our homepage (http://www.u-blox.ch/). UBX-16015271 - R03 Product Information Related documents Page 44 of 46 EMMY-W1 series - User Manual Revision history Revision Date Name Status / Comments R01 R02 R03 23-June-2016 Daniel Dietterle Draft 01-July-2016 Daniel Dietterle Document release after review 05-July-2016 Daniel Dietterle Corrected maximum output power for EMMY-W163 in Table 26 and Table 27 UBX-16015271 - R03 Product Information Revision history Page 45 of 46 Contact For complete contact information visit us at www.u-blox.com u-blox Offices North, Central and South America u-blox America, Inc. Phone:

E-mail:

+1 703 483 3180 info_us@u-blox.com Regional Office West Coast:

Phone:

E-mail:

+1 408 573 3640 info_us@u-blox.com Technical Support:

Phone:

E-mail:

+1 703 483 3185 support@u-blox.com Headquarters Europe, Middle East, Africa u-blox AG Phone:

E-mail:

Support:

+41 44 722 74 44 info@u-blox.com support@u-blox.com EMMY-W1 series - User Manual Asia, Australia, Pacific u-blox Singapore Pte. Ltd. Phone:

E-mail:

Support:

+65 6734 3811 info_ap@u-blox.com support_ap@u-blox.com Regional Office Australia:

Phone:

E-mail:

Support:

+61 2 8448 2016 info_anz@u-blox.com support_ap@u-blox.com Regional Office China (Beijing):

Phone:

E-mail:

Support:

+86 10 68 133 545 info_cn@u-blox.com support_cn@u-blox.com Regional Office China (Shenzhen):

Phone:

E-mail:

Support:

+86 755 8627 1083 info_cn@u-blox.com support_cn@u-blox.com Regional Office India:

Phone:

E-mail:

Support:

+91 959 1302 450 info_in@u-blox.com support_in@u-blox.com Regional Office Japan:

Phone:

E-mail:

Support:

+81 3 5775 3850 info_jp@u-blox.com support_jp@u-blox.com Regional Office Korea:

Phone:

E-mail:

Support:

+82 2 542 0861 info_kr@u-blox.com support_kr@u-blox.com Regional Office Taiwan:

Phone:

E-mail:

Support:

+886 2 2657 1090 info_tw@u-blox.com support_tw@u-blox.com UBX-16015271 - R03 Product Information Contact Page 46 of 46

 

 

 

 

 

 

 

 

 

 

Attn.: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Request for Class II Permissive Change Model: EMMY-W163 FCC ID: XPYEMMYW163 Letter of Agent Authorization To whom it may concern:

We, u-blox AG, hereby authorize BlueQ Services GmbH to act on our behalf in all matters relating to update the FCC listing of the modular approval for XPYEMMYW163, including the signing of all documents relating to these matters. The equipment is described as follows Model: EMMY-W163 FCC ID: XPYEMMYW163 The following persons at BlueQ Services GmbH will be authorized:

- Carsten Steinroeder We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853 (a). Thank you for your attention in this matter. Yours Sincerely Giulio Comar Certification Manager, u-blox AG C3-Confidential EMMY-W163 Letter of Agen Authorization 1/1

 

 

Application Letter for Class 2 Permissive Change BlueQ Services GmbH Hlender Weg 67 40883 Ratingen Germany Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Request for Reassessment / Class 2 Permissive change FCC ID: XPYEMMYW163 s II Permissive Change) To whom it may concern:

On behalf of u-blox AG, we hereby request a Class II Permissive Change for the FCC ID: XPYEMMYW163 to add the following new antenna:

Manufacturer: Hirschmann Car Communication Part Number: A1779052902 / 920-584-002 Description: Mercedes BT/WLAN Antenna Antenna Type: External Carsten Steinroeder BlueQ Services GmbH Managing Director Ratingen, 14/08/2023

 

 

2023-08-29 Registered office:

u-blox AG Zrcherstrasse 68 8800 Thalwil Switzerland Company number: CH-020.3.020.161-

7 info@u-blox.com support@u-blox.com Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Application for Class II Permissive Change HVIN: EMMY-W163 PMN: EMMY-W163 FCC ID: XPYEMMYW163 Letter of certification To whom it may concern:

We, u-blox AG, hereby certify that our product as described above FCC ID: XPYEMMYW163 is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). Thank you for your attention to this matter. Yours Sincerely, CFR 47 2. 903_ Letter_of_Certifi cation_XPYEMMYW163C FR 47 2.90 3_Letter_of_Certifi cation_XPYEMMY W1 63CFR 4 7 2. 903_ Letter_of_Certification_ XPY EMMYW163C FR 47 2 .90 3_Letter_of_Certifi cation_XPYEMMY W1 63CFR 4 7 2.9 03_ Letter_of_Certification_ XPYEM MYW1 63 Filip Kruzela Certification manager, u-blox AG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

U.S. Agent Designation Applicant name:

u-blox AG Address:

Info:

Subject:

To:

Zuercherstrasse 68, CH-8800 Thalwil, Switzerland www.u-blox.com U.S. Agent Designation Federal Communications Commission - Authorization and Evaluation Division Equipment Authorization Branch Address:

7435 Oakland Mills Road Columbia, MD 21046 u-blox AG, as applicant, acknowledges their consent for the following contact located in the United States to act as their agent for service of process for all applications for which authorization is sought

(FCC Grantee Code: XPY):

Name and company of U.S. agent: Dave Carey, u-blox San Diego, Inc. Physical U.S. address of agent:

12626 High Bluff Drive Suite 200 San Diego, CA 92130 FRN of U.S. agent:

0022185367 Email address of U.S. agent:

dave.carey@u-blox.com u-blox San Diego, Inc acknowledges their obligation to accept service of process on behalf of u-blox AG. u-blox AG accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01.An expiration date for this letter does not exist. Sincerely,

[Category] - R02 U.S. Agent Designation 1/2 C1-Public Signed for and on behalf of u-blox AG :

Name Position Date of issue Signature Giulio Comar Certification Manager 1 March 2023 Signed for and on behalf of u-blox San Diego, Inc. :

Name Position Date of issue Signature Dave Carey Senior Vice President 1 March 2023

[Category] - R02 U.S. Agent Designation 2/2 C1-Public