60 GHz/5 GHz Radio System with 1+ Gbps Throughput and 1.5 km Range Model: GBE-LR Package Contents Dish Main Arm Support Arms
(Qty. 2) Mounting Screw U-Clamp Flat Washers Lock Washers Bracket
(Qty. 2)
(Qty. 2) Flange Nuts
(Qty. 2) Gigabit PoE (24V, 0.5A) with Mounting Bracket Power Cord Installation Requirements Clear line of sight between GigaBeam AP and station Vertical mounting orientation Mounting point:
At least 1 m below the highest point on the structure For tower installations, at least 3 m below the top of thetower Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are required for all wired Ethernet connections. Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device and the other at the entry point to the building. The ETH-SP-G2 will absorb power surges and safely discharge them into the ground. Note: For guidelines about grounding and lightning protection, follow your local electrical regulatory codes. GBE-LR ES-8-150W ETH-SP-G2 1m ETH-SP-G2 LAN Hardware Overview LEDs 1 2 3 4 1 60 GHz 2 5 GHz 3 LAN Lights steady blue when 60 GHz link is ready. Lights steady blue when the 5 GHz link is ready. The LED will light steady blue when an active Ethernet connection is made to the Ethernet port and flash when there is activity. 4 Power/Status Color Status Flashing White Bootup in progress. White Blue Ready for use, not connected to Ubiquiti Network Management System (UNMS). See UNMS Management. Ready for use, connected to UNMS. Steady Blue with Occasional Flashing Ready for use, unable to connect to UNMS, check connection to UNMSserver. Quickly Flashing Blue Used to locate a device in UNMS. Alternating Blue/White Firmware upgrade in progress. Ports 5 6 This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Default IP address:
192.168.1.20. 5 PoE IN Port 6 Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is poweredon. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter. Installation 1. 2. 3. OPTIONAL: Attach the stabilizer arms for added support. 4. Note: The GBE-LR can mount on either side of the pole. This section shows the GBE-LR mounted on the left; the procedure for mounting on the right is similar. OR Left Right 5. 6. Note: Rotate the Mounting Bracket clockwise until it locks into position. 7. 8. 9.
(Pole not shown) 10. 11. 12. 13. Connecting Power WARNING: The switch port must comply with the power specifications listed in Specifications. OR
(Optional) Configuration The device is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, it will use the default fallback IP address, 192.168.1.20. Proceed to the appropriate section, DHCP or Fallback IP Address:
DHCP Use one of the following methods:
Set up the DHCP server to provide a specific IP address to the device based on its MAC address (on the label). Let the device obtain an IP address and then check the DHCP server to see which IP address was assigned. 1. Connect a computer to your network and configure the Ethernet adapter on your computer with a static IP address on the 192.168.1.x subnet. 2. Launch your web browser. In the address field, type:
https://192.168.1.20 Then press enter (PC) or return (Mac). https://192.168.1.20 3. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Continue. 4. Enter a Username and Password, confirm the Password, and click Save. 5. Click the icon. 6. Configure the following settings:
a. For one device, enable Access Point mode. For the other device (the Station), keep Access Point disabled. b. Enter a name in the SSID field. This must be the same on both the AP and the Station. c. In the WPA2 Preshared Key field, enter a combination of alphanumeric characters (0-9, A-Z, or a-z). Note: The key is an alphanumeric password between 8 and 63 characters long. 7. Click Save Changes. 8. Configure each device (AP and Station) with a unique IP address:
a. Click the icon. b. Review the Network settings to ensure that each device has a unique IP address. Each can get its IP address via DHCP, or use a static IP address. DHCP By default DHCP client is enabled; if there is a DHCP server on your network, the device will receive its address via DHCP. Note: If DHCP client fails, the device will use the fallback IP address: 192.168.1.20 Static Select this option to disable the DHCP client and enter a static IP address. c. Click Save Changes. Fallback IP Address 1. Ensure that your computer (or other host machine) is connected to the same LAN as the GigaBeam. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type https://192.168.1.20 in the address field, and press enter (PC) or return (Mac). https://192.168.1.20 4. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Continue. 5. Enter a Username and Password, confirm the Password, and click Save. 6. Click the icon. 7. Configure the following settings:
a. For one device, enable Access Point mode. For the other device (the Station), keep Access Point disabled. b. Enter a name in the SSID field. This must be the same on both the AP and the Station. c. In the WPA2 Preshared Key field, enter a combination of alphanumeric characters (0-9, A-Z, or a-z). Note: The key is an alphanumeric password between 8 and 63 characters long. 8. Click Save Changes. 9. Configure each device (AP and Station) with a unique IP address:
a. Click the icon. b. Review the Network settings to ensure that each device has a unique IP address. Each can get its IP address via DHCP, or use a static IP address. DHCP By default DHCP client is enabled; if there is a DHCP server on your network, the device will receive its address via DHCP. Note: If DHCP client fails, the device will use the fallback IP address: 192.168.1.20 Static Select this option to disable the DHCP client and enter a static IP address. c. Click Save Changes. Repeat the instructions in the Configuration section on the other GigaBeam. UNMS Management You can manage your device using UNMS, which lets you configure, monitor, upgrade, and back up your devices using a singleapplication. Get started at www.unms.com Alignment Tips To accurately align the radios for best performance, you MUST align only one end of the link at a time. You may need to use additional hardware to compensate for issues such as the improper orientation of a mounting pole or significant elevation differences between radios. Establishing a Link Adjust the aim of the AP and the Station to establish a link. Note: The AP must be aimed first at the Station because the Station does not transmit any RF signal until it detects transmissions from the AP. 1. AP Visually aim the AP at the Station by loosening the Flange Nuts on the Mounting Bracket to allow adjustments to the azimuth and the elevation. Adjust the azimuth:
Adjust the elevation:
20 Note: Do NOT make simultaneous adjustments on the AP and Station. 2. Station Visually aim the Station at the AP. To adjust the Stations position, adjust the azimuth and elevation as described in step 1. 3. Open the Configuration Interface. Select Tools and then select Align Antenna. 4. Repeat steps 1-2 until you have achieved an optimal link and both the 60G and 5G LEDs are solidly lit blue. This ensures the best possible data rate between the radios. Note: Maximum signal strength can best be achieved by iteratively sweeping through both azimuth and elevation. 5. Lock the alignment on both radios by tightening all the nuts. 6. Observe the signal level of each radio to ensure that the values remain constant while tightening the nuts. If any value changes during the locking process, loosen the nuts, finalize the alignment of each radio again, and retighten the nuts. Installer Compliance Responsibility Devices must be professionally installed and it is the professional installers responsibility to make sure the device is operated within local country regulatory requirements. Antenna The 5GHz Output Power field is provided to the professional installer to assist in meeting regulatory requirements. GBE-LR 415 x 415 x 303 mm (16.34 x 16.34 x 11.93") 1.3 kg (2.87 lb) Aluminum, UV-stabilized Polycarbonate Networking Interface
(1) 10/100/1000 Mbps Ethernet Port Max. Power Consumption 11 dBi 38 dBi 11W Passive PoE, Pins 4, 5+ and 7, 8-
24VDC, 0.5A Gigabit PoE Adapter (Included)
+22 to +26VDC Power/Ethernet/5G/60G 56 N @ 200 km/h (12.6 lbf @ 125 mph) Specifications Dimensions Weight Enclosure Antenna Gain 5 GHz 60 GHz Power Method Power Supply Voltage Range LEDs Wind Loading Wind Survivability Mounting ESD/EMP Protection Operating Humidity Certifications Operating Temperature
-40 to 60 C (-40 to 140 F) 200 km/h (125 mph) Pole Mount (Included) 24kV Contact/Air 5 to 95% Noncondensing FCC, IC, CE 25 dBm 2160 MHz 20/40/80 MHz Radio Max. Conducted TX Power 5/60 GHz Combined Channel Bandwidth 60 GHz 5 GHz Operating Frequency (GHz) U-NII-1 5.150 - 5.250 U-NII-3 5.725 - 5.850 57 - 66 Management Radio (MHz) 5.180 - 5.875 57 - 66 2412 - 2472 US/CA Worldwide Worldwide Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet. a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death. c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC / CAN ICES-3(A)/NMB-3(A) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 1. 2. Le prsent appareil est conforme aux CNR dISDE Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
lappareil ne doit pas produire de brouillage;
lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class A digital device. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitter FCC ID: SWX-GBELR / IC: 6545A-GBELR has been approved by FCC / ISED Canada. The device for operation in the band 5150 - 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Les dispositifs fonctionnant dans la bande de 5 510 5 250 MHz sont rsrvs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 110 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. AVIS IMPORTANT :
Dclaration sur lexposition aux rayonnements :
Cet quipement est conforme aux limites prvues pour lexposition aux rayonnements dans un environnement non contrl. Lors de linstallation et de la mise en fonctionnement de lquipement, assurez-vous quil y ait une distance minimale de 110 cm entre llment rayonnant et vous. Cet metteur ne doit tre install proximit daucune autre antenne ni daucun autre metteur, et ne doit tre utilis conjointement aucun autre de ces appareils. Australia and New Zealand Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. Brazil Nota: Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Country List AT BE BG CY CZ DE DK EE EL ES FI FR HR HU IE IT LV LT LU MT NL PL PT RO SE SI SK UK BFWA (Broadband Fixed Wireless Access) members noted in blue Note: This device meets Max. TX power limit per ETSI regulations. The following apply to products that operate in the 5 GHz frequency range:
Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz frequency range within all member states. Note: All countries listed may operate at 30 dBm. BFWA member states may operate at 36 dBm. Note: Operation in the 5.8 GHz frequency band is prohibited in BFWA member states. Other countries listed may use the 5.8 GHz frequency band. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity
[Bulgarian] UBIQUITI , GBE-LR 2014/53/EC, 2014/30/, 2014/35/.
: ui.com/compliance Hrvatski [Croatian] UBIQUITI ovim putem izjavljuje da je ovaj ureaj GBE-LR sukladan osnovnim zahtjevima i ostalim bitnim odredbama Direktiva 2014/53/EU, 2014/30/EU, 2014/35/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: ui.com/compliance etina [Czech] UBIQUITI tmto prohlauje, e toto GBE-LR zazen, je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnic 2014/53/EU, 2014/30/EU, 2014/35/EU. pln znn EU prohlen o shod je k dispozici na tto internetov adrese: ui.com/compliance Dansk [Danish] Hermed, UBIQUITI, erklrer at denne GBE-LR enhed, er i overensstemmelse med de vsentlige krav og vrige relevante krav i direktiver 2014/53/EU, 2014/30/EU, 2014/35/EU. EU-overensstemmelseserklringens fulde tekst kan findes p flgende internetadresse:
ui.com/compliance Nederlands [Dutch] Hierbij verklaart UBIQUITI, dat deze GBE-LR apparaat, in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijnen 2014/53/EU, 2014/30/EU, 2014/35/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: ui.com/compliance English Hereby, UBIQUITI, declares that this GBE-LR device, is in compliance with the essential requirements and other relevant provisions of Directives 2014/53/EU, 2014/30/EU, 2014/35/EU. The full text of the EU declaration of conformity is available at the following internet address:
ui.com/compliance Eesti keel [Estonian] Kesolevaga UBIQUITI kinnitab, et antud GBE-LR seade, on vastavus olulistele nuetele ja teistele asjakohastele stetele direktiivide 2014/53/EL, 2014/30/EL, 2014/35/EL. ELi vastavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil:
ui.com/compliance Suomi [Finnish] Tten UBIQUITI vakuuttaa, ett tm GBE-LR laite, on yhdenmukainen olennaisten vaatimusten ja muiden sit koskevien direktiivien 2014/53/EU, 2014/30/EU, 2014/35/EU. EU-vaatimustenmukaisuusvakuutuksen tysimittainen teksti on saatavilla seuraavassa internetosoitteessa: ui.com/compliance Franais [French] Par la prsente UBIQUITI dclare que lappareil GBE-LR, est conforme aux exigences essentielles et aux autres dispositions pertinentes des directives 2014/53/UE, 2014/30/UE, 2014/35/UE. Le texte complet de la dclaration UE de conformit est disponible ladresse internet suivante: ui.com/compliance Deutsch [German] Hiermit erklrt UBIQUITI, dass sich dieses GBE-LR Gert, in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinien 2014/53/EU, 2014/30/EU, 2014/35/EU befindet. Der vollstndige Text der EU-Konformittserklrung ist unter der folgenden Internetadresse verfgbar: ui.com/compliance
[Greek] , UBIQUITI, GBE-LR, 2014/53/EE, 2014/30/EE, 2014/35/EE.
: ui.com/compliance Magyar [Hungarian] Ezennel UBIQUITI kijelenti, hogy ez a GBE-LR kszlk megfelel az alapvet kvetelmnyeknek s ms vonatkoz 2014/53/EU, 2014/30/EU, 2014/35/EU irnyelvek rendelkezseit. Az EU-megfelelsgi nyilatkozat teljes szvege elrhet a kvetkez internetes cmen: ui.com/compliance slenska [Icelandic] Hr, UBIQUITI, v yfir a etta GBE-LR tki er samrmi vi grunnkrfur og nnur vieigandi kvi tilskipana 2014/53/ESB, 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samrmisyfirlsing er a finna eftirfarandi netfangi: ui.com/compliance Italiano [Italian] Con la presente, UBIQUITI, dichiara che questo dispositivo GBE-LR, conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/53/UE, 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet: ui.com/compliance Latvieu valoda [Latvian] Ar o, UBIQUITI, deklar, ka GBE-LR ierce, ir saska ar btiskajm prasbm un citiem attiecgiem noteikumiem Direktvs 2014/53/ES, 2014/30/ES, 2014/35/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams d interneta vietn: ui.com/compliance Lietuvi kalba [Lithuanian] UBIQUITI deklaruoja, kad is GBE-LR renginys atitinka esminius reikalavimus ir kitas 2014/53/ES, 2014/30/ES, 2014/35/ES Direktyv nuostatas. Visas ES atitikties deklaracijos tekstas prieinamas iuo interneto adresu: ui.com/compliance Malti [Maltese] Hawnhekk, UBIQUITI, tiddikjara li dan il-mezz GBE-LR huwa konformi mar-rekwiiti essenzjali u dispoizzjonijiet rilevanti orajn ta Direttivi 2014/53/UE, 2014/30/UE, 2014/35/UE. Id-dikjarazzjoni tal-konformit tista tii kkonsultata minn ui.com/compliance Norsk [Norwegian] Herved UBIQUITI, erklrer at denne GBE-LR enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktivene 2014/53/EU, 2014/30/EU, 2014/35/EU. Den fulle teksten til EU-samsvarserklringen er tilgjengelig p flgende internettadresse: ui.com/compliance Polski [Polish] Niniejszym, UBIQUITI, owiadcza, e urzdzenie GBE-LR, jest zgodny z zasadniczymi wymaganiami oraz pozostaymi stosownymi postanowieniami Dyrektyw 2014/53/UE, 2014/30/UE, 2014/35/UE. Peny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym: ui.com/compliance Portugus [Portuguese] UBIQUITI declara que este dispositivo GBE-LR, est conforme com os requisitos essenciais e outras disposies das Directivas 2014/53/UE, 2014/30/UE, 2014/35/UE. O texto integral da declarao de conformidade est disponvel no seguinte endereo de Internet:
ui.com/compliance Romn [Romanian] Prin prezenta, UBIQUITI declar c acest dispozitiv GBE-LR este n conformitate cu cerinele eseniale i alte prevederi relevante ale Directivelor 2014/53/UE, 2014/30/UE, 2014/35/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet: ui.com/compliance Slovenina [Slovak] Tmto UBIQUITI, prehlasuje, e toto GBE-LR zariadenie, je v slade so zkladnmi poiadavkami a almi relevantnmi ustanoveniami smernice 2014/53/E, 2014/30/E, 2014/35/E. pln E vyhlsenie o zhode je k dispozcii na tejto internetovej adrese: ui.com/compliance Slovenina [Slovenian] Druba UBIQUITI izjavlja, da je naprava GBE-LR v skladu z obveznimi zahtevami in drugimi ustreznimi dolobami direktiv 2014/53/EU, 2014/30/EU in 2014/35/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu:
ui.com/compliance Espaol [Spanish] Por medio de la presente UBIQUITI declara que este dispositivo GBE-LR, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de las Directivas 2014/53/UE, 2014/30/UE, 2014/35/UE. El texto completo de la declaracin UE de conformidad est disponible en la direccin Internet siguiente: ui.com/compliance Svenska [Swedish] Hrmed UBIQUITI, intygar att denna GBE-LR enhet r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiven 2014/53/EU, 2014/30/EU, 2014/35/EU. Den fullstndiga texten till EU-frskran om verensstmmelse finns p fljande webbadress: ui.com/compliance Online Resources Support help.ui.com Community community.ui.com Downloads downloads.ui.com Ubiquiti Inc. 685 Third Avenue New York, NY 10017 USA 2019 Ubiquiti Inc. All rights reserved. Ubiquiti, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, GigaBeam, and UNMS are trademarks or registered trademarks of Ubiquiti Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Android, Google, Google Play, the Google Play logo and other marks are trademarks of Google LLC. All other trademarks are the property of their respective owners. AI100319