M5G LiteBeam M5-23 Users Manual

 

M5G OEM Users Guide TECH SPECS SYSTEM INFORMATION Processor Specs Memory Information Networking Interface Wireless Approvals RoHS Compliance Atheros MIPS 24KC, 400MHz 32MB SDRAM, 8MB Flash 1 X 10/100 BASE-TX (Cat. 5, RJ-45) Ethernet Interface REGULATORY / COMPLIANCE INFORMATION FCC Part 15.247, IC RS210, CE YES OPERATING FREQUENCY 5745MHz-5825MHz 5GHz TX POWER SPECIFICATIONS DataRate 1-24Mbps 36Mbps 48Mbps 54Mbps MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 Avg. TX 20 dBm 19 dBm 18 dBm 16 dBm 20 dBm 20 dBm 20 dBm 20 dBm 19 dBm 17 dBm 16 dBm 15 dBm Tolerance

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB a 1 1 n 1 1 z H G 5 a 1 1 n 1 1 z H G 5 5GHz RX SPECIFICATIONS DataRate 1-24Mbps 36Mbps 48Mbps 54Mbps Sensitivity

-97 dBm min. +/-2dB

-80 dBm

+/-2dB

+/-2dB

-77 dBm

-75 dBm

+/-2dB Tolerance MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7

-96 dBm

-95 dBm

-92 dBm

-90 dBm

-86 dBm

-83 dBm

-77 dBm

-74 dBm

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB

+/-2dB Enclosure Size Weight Enclosure Characteristics Mounting Kit Max Power Consumption Power Supply Power Method Operating Temperature Operating Humidity Shock and Vibration PHYSICAL / ELECTRICAL / ENVIRONMENTAL 16cm length x 8cm width x 3cm height 0.5 kg Outdoor UV Stabalized Plastic Pole Mounting Kit included 3.5 Watts 5V USP+POE Adapter Included Passive Power over Ethernet (pairs 4,5+; 7,8 return)

-30C to 75C 5 to 95% Condensing ETSI300-019-1.4 COMPLIANCE INFORMATION FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The antennas used for this transmitter must be installed to provide a separation distance of at least following distance from all persons and must not be located or operating in conjunction with any other antenna or transmitter. 68.6cm distance for the Dish Antenna 136.9cm distance for the Grid Antenna INDUSTRY CANADA This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. The device has been designed to operate with the antennas listed below and having a maximum gain of 28dBi. Antennas not included in this list or having a gain greater than 28dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms This device must be professionally installed and is designed strictly for for outdoor point-

to-point wireless links.