FCC ID: SWX-RC7611 Radio Module

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5177369.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Product Technical Specification Table RC7611 Supported Bands / Connectivity Technology Transmit Band (Tx)

(MHz) 18501910 17101755 824849 699716 777787 788798 Receive Band (Rx)

(MHz) Maximum Output Power Notes 19301990 21102155 869894 729746 746756 758768 23 dBm 1 dB;

Class 3 MIMOa and diversity 18501915 19301995 814849 17101780 663698 859894 2110-2200 617652 RF Bandb c LTE GNSSd B2b B4b B5b B12b B13b B14b B25b B26b B66b B71b B2c B4c B5c B12c B13c B14c B25c B26c B66c B71c GPS GLONASS Galileo BeiDou a. Downlink MIMO 2x2 b. RC7611 RF Band, Cat4 variant c. RC7611-1 RF Band, Cat1 variant d. GNSS support is SKU-dependent. Rev 2.2 Feb.20 16 41113440 FCC Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment gen-

erates, uses and can radiate radio frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference to radio communications. How-

ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be de-

termined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator your body. IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated.Additional testing and certification may be necessary when multiple modules are used. Antenna The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. LABEL OF THE END PRODUCT:

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC The final end product must be labeled in a visible area with the following " Contains TX FCC ID: SWX-M11DB ". ID: SWX-M11DB ". End Product Labelling FCC Label and compliance information The final end product must be labeled in a visible area with the following: Contains FCC ID:

SWX-RC7611. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or si-

multaneous transmission with other transmitter(s) or portable use will require a separate class II per-

missive change re-evaluation or new certification. Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance re-

quirements required with this module installed. IC This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause unde-

sired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 22 cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 22 cm de distance entre la source de rayonnement et votre corps. IC This transmitter module is authorized only for use in device where the antenna may be installed such that 22cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 6545A-

RC7611. Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 22cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 6545A-RC7611". This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 22cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the ISED au-

thorization is no longer considered valid and the ISED ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluat-

ing the end product (including the transmitter) and obtaining a separate ISED autho-

rization. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositive module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 22cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. NOTE IMPORTANTE: Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-

localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID ISDE ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. The OEM integrator must not provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel.

25mm FCC ID: SWX. IC: 6545A-HL7300 MIN:

10mm 25mm FCC ID: SWX-RC7611 IC: 6545A-RC7611 M/N: RC7611 M/N: RC7611U Top side of shielding case

Date: 2020-11-25 FCC ID: SWX-RC7611 AUTHORIZATION LETTER To Whom It May Concern:

Ubiquiti Inc. hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on Ubiquiti Inc.s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours, Mark Feil / Compliance Manager Ubiquiti Inc. Tel: 408-942-3084 Fax: 408-904-5255 E-mail: compliance@ubnt.com

Date: 2020-11-25 Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Subject: Request for Confidentiality FCC ID: SWX-RC7611 Authorizations. External photos Internal Photos Test Setup photos Best Regards, Mark Feil / Compliance Manager Ubiquiti Inc. Tel: 408-942-3084 Fax: 408-904-5255 E-mail: compliance@ubnt.com To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459) and Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Users manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued.

Class II Permissive Change We, Ubiquiti Inc., hereby declare that the intention of this Class II Permissive. Change is to add a host: UISP-LTE (Model: UISP-LTE/ Brand: Ubiquiti Inc.) to certified module which was originally granted on 08/14/2020 under FCC ID: SWX-RC7611 . The main change is that only support LTE bands 2, 4, 5, 12 and the power of band 2, 4 is reduced, so Conducted and RSE need to be evaluated. In addition, the antenna gain and the MPE distance have both increased, so RF Exposure needs to be evaluated. Except for the changes mentioned above, no other modification is performed. Should you have any question, please contact me directly. Date: January 19, 2021 FCC ID: SWX-RC7611 Sincerely, Mark Feil / Compliance Manager Ubiquiti Inc. Tel: 408-942-3084 Fax: 408-904-5255 E-mail: compliance@ubnt.com

August 14, 2020 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 Re:

Change of Identification Authorization Reference:

FCC ID: N7NRC76B To Whom It May Concern:

This letter grants authorization for Ubiquiti Inc. to apply to the FCC for a change in identification as specified under 47CFR Section 2.933 of the FCC rules. This authorization applies to Sierra Wireless module, FCC ID: N7NRC76B based on the grant issued on 02/05/2020. We are aware that Ubiquiti Inc. intends to market the above referenced product under FCC ID: SWX-RC7611. Sincerely, Denis Chabot Senior Manager, Certification

September 7, 2016 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 RE: Authorization Letter for Grantee Code N7N Dear Sir/Madam:

I hereby authorize Mr. Denis Chabot of Sierra Wireless to act on my behalf in all manners relating to the application for equipment authorization including signing of all documents relating to these matters. Any and all acts carried out by Mr. Denis Chabot of Sierra Wireless on my behalf shall have the same effect as acts of my own. Sincerely, Ying Wang Manager, Regulatory Compliance

Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Date: August 10, 2020 Attention: Application Examiner / Review Engineer Subject: Request to change in identification per section 2.933 of FCC rules Reference: FCC ID: SWX-RC7611 To The Commission:

This Change of Identification request applies for a new FCC ID: SWX-RC7611 as established in 47CFR 2.933(b) for a currently approved device. This application by Ubiquiti Inc. will establish a new FCC ID under SWX-RC7611 grantee code for purpose of marketing. The original grant to N7NRC76B will remain in effect. An authorization letter by Sierra Wireless Inc. is attached. Per 2.933(b) 1. The original identification is N7NRC76B 2. The original grant date is 02/05/2020 3. The equipment is electrically identical. Only the FCC ID number is different. 4. The original test results are applicable and representative of device bearing changed identification.. 5. Exterior photographs are included in this application. The following files are electronically submitted as attachments:

Cover Letter External Photos FCC ID label format and location Sincerely yours, Mark Feil / Compliance Manager Ubiquiti Inc. Tel: 408-942-3084 E-mail: compliance@ubnt.com