Datasheet UISP-FIBER-OLT-XGS UISP Fiber XGS/XG/G-PON OLT Mechanical Dimensions Weight Enclosure material Hardware Networking interface Management interface Memory UISP-FIBER-OLT-XGS 442.4 x285.6 x43.7 mm (17.4x 11.2x 1.7") 5.29 kg (11.7 lb) SGCC steel
(8) XGS/XG/G-PON OLT
(4) 1/10/25 Gbps SFP28 Ethernet*
*The four SFP28 ports don't support mixed speed at 25Gbps mode. Once one of the SFP28 ports is congured at 25Gbps mode, the others will be limited at 25Gbps too. The SFP28 ports only support mixed speed when all ports are at 1Gbps or 10Gbps. Ethernet out-of-band Ethernet in-band RJ45 serial console port Bluetooth 512 MB DDR3 Onboard ash storage 64 MB NOR + 512 MB NAND Power method Power supply
(1) Universal AC input, 100-240VAC, 50/60 Hz
(2) Hotswap AC/DC PSU Supported voltage range 100240VAC Max. power consumption 60W (excluding SFP modules) Button
(1) Factory reset Operating temperature
-10 to 45 C (14 to 113 F) Operating humidity Certications LEDs System RJ45 data ports SFP data ports SFP+ data ports 10 to 95% non-condensing CE, FCC, IC Slow blinking white: system is booting Fast blinking white: reset to default Blinking white/blue: system is upgrading Slow blinking blue: system is connecting to UISP Fast blinking blue: locate system Steady white: system is ready Steady blue: system is ready and connected to UISP
(1) White, steady on after link is up
(8) Steady white: GPON link
(4) White, steady on after link is up Specifications are subjec t to change. Ubiquiti products are sold with a limited warranty described at: ui.com/support/warranty 2022 Ubiquiti Inc. All rights res erv ed. Ubiquiti, Ubiquiti Network s, the Ubiquiti U logo, and UISP are trademarks or registered trademarks of Ubiquiti Inc. in the United States and in other countries. All other trademarks are the property of their res pec tiv e owners. FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause un-
desired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, maycause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help."
ISED Canada CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is sub-
ject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired opera-
tion of the device. CAN ICES-3(A)/NMB-3(A) Le prsent appareil est conforme aux CNR dISDE Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. lappareil ne doit pas produire de brouillage;
2. lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est sus-
ceptible den compromettre le fonctionnement. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20(FCC/IC) cm from all persons and must not be located or operating in con junction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une dis tance de sparation de toute personnes daumoins 20 (FCC/IC) cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur.`