FCC ID: 2AHJX-UKBTC01 Bluetooth controller

6. Combined keys 7. Specication and parameters Switch the main mode from the mode (L2+R2+Bluetooth button) The default state of the Bluetooth gamepad is the master mode. When the Bluetooth gamepad is not connected and the combination key

(L2+R2+Bluetooth button) is pressed, after 5 seconds, the four indicator lights will ash rapidly. Upon releasing the button, the Bluetooth gamepad switches to the slave mode. To switch back to the master mode, simply restart the handle. Joystick calibration button (L1+R1+Bluetooth button) When the Bluetooth gamepad is not connected and the combination key

(L1+R1+Bluetooth button) is pressed, after 5 seconds, the three red indicator lights will ash rapidly. Upon releasing the button, the joystick rotates through 360 degrees and the three indicator lights turn o, indicating successful calibration. Product Name Product Model Operation Temperature Input Bluetooth Controller UKBTC01 0~35 5V 0.2A Frequency range 2402~2480MHz RF transmitting power Maximum transmitting power 4dBm Maximum control distance 10 meters in an open environment Bluetooth version Bluetooth 4.0 Battery capacity 550 mA Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note:

Please use a 5V adapter for charging. Please check the battery level before use and charge it in time, avoiding using it while charging. When using this product, keep away from re sources and avoid charging or using it in extreme high or low temperature environments. Keep away from water sources and ensure the product is dry and clean. Do not attempt to disassemble this product without authorization. Please avoid placing this product on high or edge positions to prevent it from falling and damage. Machine damage caused by human error is not covered by our warranty. Please do not peel o the label on the back of the Bluetooth controller. FCC ID: 2AHJX-UKBTC01 R-R-700-UKBTC01 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. 1.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interfer-

ence that may cause undesired operation. 2.Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Quick guide for Bluetooth controller X Y A B P05 P06 P07 P08 1. Global Preview 2. Introduction to buttons 3. Introduction to Bluetooth mode 5. Matching method L1L2 Bluetooth start-up R1R2 switch Bluetooth button Switch button Start button Function buttons L2 R2 L1 R1 Left Rocker Direction buttons Right Rocker Function buttons Rocker button Main mode Bluetooth pairing Long press the switch button to turn on the Bluetooth controller, and the blue indicator light starts ashing slowly. Hold the Bluetooth controller near the controller you want to pair with, and then long press the Bluetooth button until the blue indicator light starts ashing rapidly. Release the Bluetooth button, and the Bluetooth connection will be established automatically. A solid blue indicator light indicates a successful pairing. Main mode (default mode) Used for controlling robots. From the mode Used to control the stage mode of uCode programming software. 4. Indicator light The blue indicator light indicates the Bluetooth connection status. The red indicator light indicates the power status. Four indicator lights ashing rapidly indicate:

switching between main and sub modes. The blue indicator light ashes slowly:

Bluetooth is waiting for pairing. The blue indicator light ashing rapidly:

Bluetooth is in the process of pairing. The blue indicator light remains on:

Bluetooth pairing successful. Three red indicator lights on indicate:

the handle has sucient battery power. Three red indicator lights ashing rapidly indicate:

joystick calibration mode. Two red indicator lights on indicate:

the remaining battery power is less than 50%. The red indicator light on indicates:

the remaining battery power is less than 20%. A single red indicator light ashing rapidly indicates:

low battery. Scan the QR code to get the electronic quick guide This guide does not constitute any form of commitment. Products (including but not limited to color, size, quantity, etc.), related information and pictures are for reference only. Please refer to the actual product. UBTECH ROBOTICS CORP LTD Add: Room 2201, Building C1, Nanshan Smart Park, No.1001 Xueyuan Avenue, Changyuan Community, Taoyuan Street, Nanshan District, Shenzhen, PRC Web: www.ubtrobot.com P01 P02 P03 P04 500*140mm 100*140mm 105g 4, 0.5mm A

1210200376 A 1mm

2023-10-10 ID

/ID

) 1. 2. 3. 2023-10-10 1. 2.

//FCC/IC/CMIIT ID 2023-10-10

UBTECH ROBOTICS CORP LTD Product Name: Bluetooth Controller Product Model: UKBTC01 Input: 5V 0.2A FCC ID: 2AHJX-UKBTC01 Made in China R-R-700-UKBTC01

38*28mm 128g SN UBTECH ROBOTICS CORP LTD Product Name: Bluetooth Controller Product Model: UKBTC01 Input: 5V 0.2A FCC ID: 2AHJX-UKBTC01 Made in China R-R-700-UKBTC01

UBTECH ROBOTICS CORP LTD Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: October 16, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AHJX-UKBTC01 UBTECH ROBOTICS CORP LTD (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature:

Printed name: Wayne Cheng Rev 2/17/2023

UBTECH ROBOTICS CORP LTD Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: October 16, 2023 Attestation Statements Part 2.911(d)(5)(ii) Filing Ref:

FCC ID: 2AHJX-UKBTC01 UBTECH ROBOTICS CORP LTD (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Signature:

Printed name: Wayne Cheng Rev 2/17/2023

UBTECH ROBOTICS CORP LTD Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AHJX-UKBTC01 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type

(Block Diagram, Schematics, Operational Description) File Name

(Block Diagram.pdf, Schematics.pdf, Operational Description.pdf) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request that the information attached to this application be temporarily confidential for 180 days as outlined below:

File Name

Exhibit Type

Sincerely, Signature:

printed name: Wayne Cheng Date: October 18, 2023 Rev 11/20/07

UBTECH ROBOTICS CORP LTD Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023-10-16 SUBJECT: FCC SDoC declaration for FCC ID: 2AHJX-UKBTC01 To Whom it may concern, We, as the grantee of this project, would like to declare that this device has been tested according to the FCC requirement and found compliant with the following standards: FCC Part 15 Subpart B. Product Name

: Bluetooth controller Brand Name

: UBTECH Model Name

: UKBTC01 Testing Lab

: Centre Testing International Group Co., Ltd Sincerely, Signature: ________________________________ Company Name

: UBTECH ROBOTICS CORP LTD Name Job Title E-mail Tel.

: Wayne Cheng

: Manager

: wayne.cheng@ubtrobot.com

0755-83474428

UBTECH ROBOTICS CORP LTD Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: October 16, 2023 SUBJECT: FCC Application for (FCC ID: 2AHJX-UKBTC01) To Whom It May Concern:

We, the undersigned, hereby authorize Mina Xu at Centre Testing International Group Co., Ltd / Building C, Hongwei Industrial Park Block 70, Bao'an District, Shenzhen, China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Mina Xu at Centre Testing International Group Co., Ltd /

Building C, Hongwei Industrial Park Block 70, Bao'an District, Shenzhen, China on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Signature:

printed name: Wayne Cheng M:\Master Documents\TEMPLATES\POA_Letter.doc

UBTECH ROBOTICS CORP LTD Address: Room 2201, Building C1 Nanshan Smart Park, No. 1001 Xueyuan Avenue Changyuan Community, Taoyuan Street Nanshan District Shenzhen, China Date: October 16, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AHJX-UKBTC01 Applicant FRN: 0025344045 US Agent Attestation Statement / Part 2.911(d)(7) UBTECH ROBOTICS CORP LTD certifies, that as of October 16, 2023, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2AHJX-UKBTC01 UBTECH ROBOTICS CORP LTD accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-

related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of UBTECH ROBOTICS CORP LTD for FCC ID: 2AHJX-UKBTC01 Designated Agent Information:

Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: Support@FCCUSAgent.com Sincerely, Company: UBTECH ROBOTICS CORP LTD Designated Agent: FCC US Agent, LLC Company Representative: Wayne Cheng Designated Agent Representative: Tim Payne Signature:

Signature: