i s o d a r y a w
-
2 S R F GMR5088-2CKHS, GMR5095-2CKHS GMR5098-2CKVP 22 FRS Channels 7 Weather Channels 142 Privacy Codes (CTCSS Tone and DCS Code) Up to 50 Mile Range*
Internal VOX Circuitry TRU Waterproof (JIS7) Submersible and Floats Direct Call with Name Display 143 Group Codes Silent Mode 10 Selectable Call/Ring Tone Alerts Backlit LCD Display Roger Beep Call Alert; Vibrate 2 Earbuds with VOX Mic or 2 Headset Boom Mics BOOST for Maximum Range*
Headset Jack Auto Channel Change Call Battery Level Meter Rechargeable NiMH Batteries Dual Charging Cradle with AC Adapter Channel Monitor Channel Scan Group Scan Keypad Lock Emergency Weather Alert Emergency Light
*Range may vary depending on environmental and/or topographical conditions. LIQUID CRYSTAL DISPLAY 15 16 17 18 19 11 12 13 14 1 2 3 4 5 6 7 8 9 10 Radio color/pattern varies according to model number. 1 2 3 4 5 Antenna Push to Talk Boost Monitor Channel Up/Down Tone D Call Microphone Speaker Flashlight/Monitor Menu/Power Volume Up/Down 6 7 8 9 10 11 12 13 Weather 22 24 20 21 CHARGING CRADLE 23 25 Enter/Lock Battery Level 14 15 16 Group Number 17 Group Indicator 18 RX (Receive) or TX
(Transmit) Indicator VOX Indicator 19 20 Missed Call Indicator 21 22 23 24 25 miniUSB port Alert Indicator Channel Number Charging LED Charging contacts Congratulations on your purchase of a Uniden FRS waterproof radio. These lightweight, palm-
sized, radios are state-of-the-art devices. The GMR5088-2CKHS and GMR5095-2CKHS models include earbud vox mics. GMR5098-
2CKVP includes two VOX headset boom mics. Use them at sporting events to contact family and friends, while hiking, skiing, or outdoors, or in a neighborhood watch for vital communication even outside by the pool! Don't worry; they float!
Your radio complies with IPX7 water-
resistant standards, which means the radio can be submerged in 1.0 meters of water for 30 minutes without damage. The radio will only meet this rating if fully assembled and all rubber seals and the jack cover are well maintained and correctly fitted. This means that the Headset plug is inserted, and the Headset jack cover and the battery pack are attached and securely fastened. After your radio is submerged in water, you might notice that the sound is distorted. This is because water remains in and around the speaker and microphone. Just shake the radio to clear excess water, and the sound should return to normal. Note: If your radio is exposed to salt water, clean your radio thoroughly with fresh water and dry it before turning it on. PACKAGE CONTENTS Your package contains two radios, 6 rechargeable AA NiMH batteries, one AC adapter with microUSB connector, one charging cradle, 2 earbud/mic headsets for GMR5095-2CKHS and GMR5088-2CKHS (GMR5098-2CKVP has two headset boom mics), two belt clips, and this reference guide. To order the following optional accessories, visit our web site at www.uniden. com. Use only Uniden accessories. NiMH Batteries #BP-38 Charging Cradle #RC-658R Headset Boom Mic #ZA-133 or ZA-160 AC Adapter #AD-0001 Carabiner Clip #TSTD0720002 INSTALL THE BATTERY Each radio uses 3 rechargeable AA NiMH batteries for power (included). It can also use non-rechargeable AA alkaline batteries (not included). To install the NiMH batteries:
1. Turn the screw holding the battery compartment counterclockwise with a screwdriver and lift up the battery cover, 2. Insert the NiMH batteries in the battery compartment according to the directions indicated on the battery tray. Installing the batteries incorrectly will prevent the unit from operating. 3. Before placing the battery cover back on the radio, check the rubber seal around the battery compartment. Make sure that the seal is in good condition and that there is no foreign matter under it. 4. Replace the battery compartment door. Tighten the screws securely. Note: If the rubber seal appears worn, nicked, or dried out, replacement seals are available from www.uniden.com. CHARGING THE RADIO Follow these instructions to charge or recharge your radios. Make sure to turn the radio OFF before placing it in the charging cradle. 1. Insert the adapter's microUSB plug to DC IN 5V USB jack of the charging cradle and plug the other end into an AC outlet. 2. Set the charging cradle on a stable desk or tabletop and place the radios in the charging cradle with the keypad facing forward. 3. Make sure that the LED illuminates. Charge the batteries for 16 hours and remove the radio from the charging cradle after charging. Note:
Use only the supplied batteries and AC adapter or approved accessories from Uniden. Charge time may vary depending on the battery life remaining. The batteries must be installed for the unit to operate, even if the unit is also connected to external power. If battery power is low, you cannot operate the radio even using external power. Allow the batteries to charge before using. If you try to transmit while power is low, the radio will automatically turn off. Do not recharge alkaline batteries. Doing so can create a safety hazard or damage the radio. For faster charging, turn off the radio before charging. Warning!
The charging cradle is not waterproof. If the charging cradle falls in the water, unplug it before attempting to remove it from the water. Allow the cradle to dry completely before reconnecting the power. cord. The GMR5098-2CKVP comes with boom mic headset. To use a headset, lift the rubber cover from over the headset jack, then plug in the headset. Important: Your radio is not waterproof when using a headset jack. When you remove the headset, be sure to fully press the jack cover into place to restore its waterproof capability. USING RADIO BATTERY LEVEL AND LOW BATTERY ALERT Your radio has a battery level meter that indicates the battery power level. When the battery level is low, the battery level meter icon flashes and then BATT appears after 30 seconds. Recharge the NiMH batteries immediately. Warning! To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden accessories specifically designated for this product. USING THE RADIO In order to get the most out of your new radio, read this reference guide completely before attempting to operate it. Turning the Radio On and Adjusting the Volume 1. Press and hold MENU/
to turn the radio 2. Press VOL or to increase or decrease the volume level then press ENTER/
. 3. Press and hold MENU/
to turn the radio on. off. Choosing a Channel Your radio has 22 channels and 142 Privacy codes you can use to talk to others. In order to speak to someone, both your radios must be set to the same channel and Privacy code. To choose a channel:
To scroll through the channels one at a time, or press CH to scroll rapidly through the channels. Note: Channels 1-7 and 15-22 have a typical range of up to 50 miles by pressing BOOST. HI displays when you select a high-power channel, and LO displays when you select a low-power channel. Press and hold CH or Wipe off dirt or shake water from your radio before placing in the charging cradle if your radio is soiled or wet. USING A HEADSET GMR5088-2CKHS and GMR5095-2CKHS both come with an earbud headset with mic on the SETTING UP GROUP MODE Group mode lets several people talk on the same channel in a separate group. In order to use Group mode, you need to initialize specific settings in your radio:
Set the radio to Group mode. Set a Group Code. Set a Unit Number. Set a "Nickname."
Setting the Radio to Group Mode To set the radio to Group mode, which enables Direct Call, Auto Channel Change, and All Call, press and hold TONE/GROUP for 2 seconds. The radio displays GRP and group code. Note: In Group mode, you cannot receive transmissions from other radios unless they are also set to the same channel and group code. Setting the Group Code Set the group code for your radio group from 0-142. Everyone in your group must select the same group code in order to communicate with each other. 1. PressTONE/GROUP in Group mode. to select the group or Press CH number. 2. Press ENTER/
or TONE/GROUP to return to normal operation. Setting the Unit Number Each radio in your group needs to be set to a unique unit number, from 1-16. 1. Press MENU/
. Advance through the menu until UNIT appears, and then press ENTER/
flashes. The current unit number to select the desired 2. Press CH or unit number. 3. Press ENTER/
to continue to the next section. Setting Your Nickname Your nickname appears on other units displays when you make an All Call or Direct Call. This is also the name that appears on other radio displays when someone wants to make a Direct Call to you. Without a nickname, the unit number shows. 1. Press MENU/
. Advance through the
. The current unit number menu until UNIT appears, and then press ENTER/
flashes, then press ENTER/
. The radio displays - - - - (or your current nickname) with the first place in the nickname flashing. 2. Press CH or to select the letter, to advance to the next then ENTER/
letter until you have entered your nickname. to confirm the setting and 3. Press MENU/
exit the menu. Using Group Mode Group mode lets you make direct calls to other people in your group without alerting the entire group and also lets you quickly change everyone in your group to another channel from a single radio. Before using Group mode, follow the instructions in "Setting Up Group mode" on or
. Everyone in your
. Your radio sounds tones for 3 every radio in your group. Then, to record the unit ID and everyones nickname in every radio, send a call to "All" from each radio one time
(see "Sending a Direct Call"). Sending a Direct Call Direct Call lets you call everyone in your group at once, or call a single person in your group without anyone else in the group knowing. It is like a "speed dial" directly to the person(s) you want to talk to. To call everyone in your group, press D CALL in Group mode. The radio flashes ALL. Then, press D CALL or ENTER/
group receives a call "chirp" for about 3 seconds. When the chirp ends, begin your conversation. Note: When you make a direct call to "all," your radio also sends out your nickname or ID so that it will show up in the call list for everyone in your group. To call one person in your group without having other people know, press D CALL in Group mode. Then, use CH to select the person you want to call and press D CALL or ENTER/
seconds as it sends the call. When the selected person answers, you can begin your conversation. You can silence the call tones any time by pressing PTT or BOOST. Your conversation remains private between you and the person you called until 15 seconds after your last conversation. Then, your radio automatically exits Private mode. Automatically Changing Channels Auto Channel Change lets you easily coordinate a channel change for everyone in your group. You might want to do this when you find you are getting a lot of interference on your current channel. You also use this feature to change from a low-power channel (8-14) to one of the high-powered channels (1-7, 15-22) for more range (or to a low-power channel if you need longer battery life). To start an auto channel change, on any radio in the group, press MENU/
the menu until CHCX appears, then press ENTER/
or CH can check whether the selected channel is clear. Then press D CALL or ENTER/
Your radio chirps for about 10 seconds while it sends out the channel change signal. As each radio receives the channel change signal, it chirps once, then changes to the new channel. To ensure all radios make it to the new channel, we recommend you:
Make sure you are in an open environment,
. The current channel flashes. Use to select the target channel. You
. Advance through
. where the radio will get the best range. Optimize range during the channel change signal by raising the radio over your head to give the best possible height. Do a "roll call" on the new channel after the move to be sure no one was left behind. If you missed someone, return to the previous channel and issue the signal again. USING THE RADIO IN STANDARD MODE Use the radio in Standard (not Group) mode when you need to be able to communicate with radios that do not have the group feature. Choosing a Privacy Code You can select a Privacy Code from 1-142 for each channel. oF (off) indicates no Privacy Code selected and your radio can receive a signal regardless of the code settings of the transmitting radio. 1. Press TONE/GROUP. The Privacy Code indicator flashes. or 2. Press CH to increase or decrease the code. You can also select oF. 3. Press ENTER/
or TONE/GROUP to return to normal operation. Note: Only tones 1-38 are standard across radio brands. Other settings might differ from brand to brand. See the specifications for the specific tones used for each setting. Channel Scan Feature Your radio has a channel scan feature that lets you easily scan all 22 channels. When an active channel is detected, the radio pauses on that channel until the channel is clear. Then after a 2-second delay, the radio resumes scanning. Pressing PTT or BOOST while the scan is paused on a channel lets you transmit on that channel. To turn on channel scan:
. The radio displays SCAN. Press MENU/
Press ENTER/
.The channel number changes as the radio rapidly cycles through the channels. Use the radio in Standard (not Group) mode when you need to be able to communicate with radios that do not have the group feature. Talking on Your Radio To talk to others using the radio:
1. Press and hold PTT or BOOST and speak in a clear, normal voice about 2-3 inches away from the microphone. While you transmit, TXHI or TXLO appears on the display according to the type of channel. To avoid cutting off the first part of your transmission, pause slightly after pressing PTT or BOOST before you start talking. 2. When you finish speaking, release PTT or BOOST. You can now receive incoming calls. While receiving, RX appears on the display. Note:
When you press BOOST, BOOST appear on the display. The radio transmits at maximum power when a GMRS channel is selected. If BOOST, PTT or VOX is continuously used, 1 minute after you start using the feature the transmission stops and you hear a timeout error tone. Monitor Mode Feature Your radio lets you listen for weak signals on the current channel at the press of a key. To turn on the Monitor mode:
Press and hold LIGHT/MON for 2 seconds until two beeps sound for continuous listening. The receiver circuit stays open, so you hear both the noise and weak signals. To turn off Monitor mode:
Press LIGHT/MON to return to the previous mode. MON and RX disappear. Navigating through the Normal Menu Your radio has a Menu function to access advanced features. In order to use Auto Channel Change, you need to set your radio to Group mode. Scan Mode Silent Mode Start Scanning ON-OFF Beep Tone Roger Beep ON-OFF ON-OFF VOX Level OFF, 1-5 Call Tone 1-10 Auto Channel Change Channel Change Unit Setting Setting Unit Number Setting Nickname 1. To enter the menu, press MENU/
2. Press MENU/
again to advance through
. the menu. After the last menu item, the radio exits to the previous mode. 3. Other ways to exit the Menu function are:
a. Press PTT, BOOST, LIGHT/MON, D CALL, WX/ALERT or TONE/GROUP. b. Wait 10 seconds until the radio automatically returns to the previous mode. Setting Silent Mode When you turn on Silent mode, all incoming calls are muted, the display backlight flashes, and the channel indicator displays SLNT and CALL to alert you to an incoming call. If you do not respond to the call within 15 seconds, the backlight turns off. The GMR5095 will also vibrate to remind you that you missed a call. Silent mode is disabled for 15 seconds when you transmit, receive, or press any other button. To set Silent mode:
1. Enter the menu. Advance through the menu until the SLNT displays, then press ENTER/
2. Press CH
. The current setting flashes. to display on, then press ENTER/
Note: To prevent unwanted silent alerts, be sure to use a Privacy Code or Group Code whenever you use the Silent mode feature. You can hear the received voice when you turn on channel scan and an active channel is detected, even during Silent mode. Missed Call Alerts If you receive an incoming call while Silent mode is on and do not respond, the radio will turn on the Missed Call icon. If you are using Group mode, the radio will also indicate who made the call. The GMR5095 will also remind you of a missed call by vibrating every minute after the call for 3 minutes. Voice Operated Transmission Your radio is equipped with a user selectable Voice Operated Transmitter (VOX) that can be used for automatic voice transmissions. The VOX feature is designed to be used with a headset with a microphone. Initiate transmission by speaking into the remote microphone instead of pushing PTT and BOOST. To select the VOX level:
1. Press MENU/
. Advance through the Menu until VOX appears on the display, then press ENTER/
. The current level
(off, 1-5) flashes. Level oF (off) disables VOX, while levels 1-5 set the sensitivity of the VOX circuit. 2. Press either CH to reach the or desired VOX sensitivity level, then press ENTER/
. Use level 1 for increased sensitivity to voice in normally quiet environments, and use a higher level to reduce undesired activation in very noisy environments. Transmitting a Call Tone Your radio is equipped with 10 selectable call tones that are transmitted when you press D CALL in Standard mode. The selected tone also will be heard when someone places a direct call to you. To select a call tone:
1. Press MENU/
. Advance through the menu until CALL appears, then press ENTER/
(1-10) flashes. The current call tone number 2. Press CH or to increase or decrease the number to the desired call tone. Each tone will be heard through the speaker. Press ENTER/
to select a call tone. The current setting flashes. to display oF, then press ENTER/
to display on, then press ENTER/
To transmit the selected call tone, press D CALL. The selected tone is transmitted for a fixed length of time. Press PTT or BOOST to cancel. Roger Beep Roger Beep is a beep that is sent to notify the end of transmission (both PTT and VOX transmission). You can hear Roger Beep through the speaker when both Roger Beep and Beep Tone are on. When Roger Beep is on and Beep Tone is off, you do not hear Roger Beep, but it is transmitted to your party. To adjust Roger Beep, press MENU/
. Advance through the menu until RGR appears, then press ENTER/
To turn off Roger Beep:
Press CH To turn on Roger Beep:
Press CH Adjusting the Sound (Beep Tone) Your radio sounds a beep each time you press a key (except for PTT and BOOST). To adjust the sound, press MENU/
through the menu until TONE appears, then press ENTER/
To turn off the beep:
Press CH To turn on the beep:
Press CH ENTER/
Key Lock Press and hold the ENTER/
appears. To turn Keylock off, press and hold ENTER/
again. Note:
If Keylock is on, the radio can still receive transmissions. Use D CALL in Standard mode, VOL
, PTT, BOOST, LIGHT/MON, and MENU/
to display oF, then press ENTER/
to display on, then press
. The current setting flashes. to turn the radio on or off. until LOCK
. Advance or
. The radio retains the keylock status even when you cycle power. Using the Flashlight You can use this radio in an emergency. If you press LIGHT/MON, the radio turns on the high-
intensity LED flashlight on your radio. Depending on how you set it up, the LED functions as a flashlight, flashes S O S in international Morse Code, is always on, or is off. Note: Your radio operates normally when the SOS strobe is activated. 1. Press LIGHT/MON while this light is turned off, the Strobe Light emits the SOS signal.
(Strobe SOS mode) 2. And then, press LIGHT/MON once more, it will turn on continuously. (Always On mode) 3. And then, press LIGHT/MON while Always On mode, the light will be turned off. Automatic Power Save Feature Your radio has a unique circuit designed to dramatically extend the life of the battery. If you do not transmit and do not receive an incoming call within 3 seconds, your radio switches to the Power Save mode. The radio is still able to receive transmissions in this mode. LCD Backlight The LCD Backlight automatically turns on when any key (except for PTT and BOOST) is pressed. The LCD remains lit for 10 seconds before turning off. USING THE WEATHER RADIO Your radio can receive weather broadcasts from the NOAA National Weather Service. When in Weather Radio Alert mode, the system functions as it does in Standard mode or Group mode but also monitors the selected weather channel for alerts when not communicating. While using the Weather Radio, you are not able to receive FRS communications. 1. To turn on the Weather Radio Broadcast mode, press WX/ALERT. WX appears. 2. Press CH to increase or decrease the number to the desired Weather Channel. 3. To exit the Weather Radio Broadcast mode, or press WX/ALERT. WX disappears. When in the Weather Radio Broadcast mode, you can only set the Beep Tone from the Menu mode. Choosing an Emergency/Weather Channel There are 7 NOAA channel frequencies available and these frequencies are common between the US and Canada. You need to know what frequency is being transmitted in your location. 1. Press and hold WX/ALERT. appears. 2. When the unit receives a warning signal, it beeps for 5 seconds. indicator flash. and channel 3. To turn off Weather Alert, press and hold WX/ALERT. disappears. When Weather Alert is activated, the highest priority is given to this function. It checks the weather alert signals every 7 seconds. When the unit finds a warning signal, it switches to the Warning Receive mode automatically. Weather Alert is activated even if Beep Tone is off. Chan. Chan. NOAA Weather Radio Frequency List:
Freq.
(MHz) 162.450 162.500 162.525 Freq.
(MHz) 162.550 162.400 162.475 162.425 1 2 3 4 5 6 7 SPECIFICATIONS Specification 22 FRS/7 Weather Item Channels Privacy Codes Operating Frequency (MHz) GMRS/FRS:
38 Sub-Codes 83 DCS Codes 462.5500 - 467.7125 WX:
Power Source Range
(Chan.) 1-7 162.4000 - 162.5500 Per radio: 3 AA NiMH Batteries
(700 mAh) Miles Up to 18 (up to 50 with BOOST) 8-14 15-22 Battery Life
(Hours) Up to 5 Up to 18 (up to 50 with BOOST) 8.5 Hours (typical) -- NiMH Batteries (5/5/90 duty cycle) FREQUENCIES Frequency Chart CH. Freq. Cross-Ref. CH. Freq. Cross-
Ref. 1 2 3 4 5 6 7 8 9 462.5625 FRS & GMRS 1 462.5875 FRS & GMRS 2 462.6125 FRS & GMRS 3 462.6375 FRS & GMRS 4 462.6625 FRS & GMRS 5 462.6875 FRS & GMRS 6 462.7125 FRS & GMRS 7 467.5625 FRS 8 467.5875 FRS 9 10 11 467.6125 FRS 10 467.6375 FRS 11 12 13 14 15 16 17 18 19 20 21 22 467.6625 FRS 12 467.6875 FRS 13 467.7125 FRS 14 462.5500 GMRS 11 462.5750 GMRS 8 462.6000 GMRS 12 462.6250 GMRS 9 462.6500 GMRS 13 462.6750 GMRS 10 462.7000 GMRS 14 462.7250 GMRS15 Note: This product is considered FRS only with 22 FRS channels in the US market. It is considered a GMRS product in the Canadian market. CTCSS & DCS CODES CTCSS Chart (Hz) Code oF 1 2 3 Freq. OFF 67.0 71.9 74.4 Code 13 14 15 16 77.0 79.7 82.5 85.48 88.5 91.5 94.8 97.4 100.0 4 5 6 7 8 9 10 11 12 DSC Code List 17 18 19 20 21 22 23 24 25 Freq. 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 Code 26 27 28 29 30 31 32 33 34 35 36 37 38 Freq. 162.2 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 Tone No. 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Octal Code 023 025 026 031 032 043 047 051 054 065 071 072 073 074 114 115 116 125 131 132 Tone No. 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 Octal Code 174 205 223 226 243 244 245 251 261 263 265 271 306 311 315 331 343 346 351 364 Tone No. 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 Octal Code 445 464 465 466 503 506 516 532 546 565 606 612 624 627 631 632 654 662 664 703 Tone No. 59 60 61 62 63 64 65 66 Octal Code 134 143 152 155 156 162 165 172 Tone No. 87 88 89 90 91 92 93 94 Octal Code 365 371 411 412 413 423 431 432 Tone No. 115 116 117 118 119 120 121 Octal Code 712 723 731 732 734 743 754 RBRC Information As part of our commitment to protect the environment and conserve natural resources, Uniden voluntarily participates in an RBRC industry program to collect and recycle used Ni-MH batteries within the US. Please call 1-800-8-BATTERY for information on Ni-MH battery recycling in your area. (RBRC is a registered trademark of the Rechargeable Battery Recycling Corporation.) MAINTENANCE To be safe and sure:
Never open your radios case. Never change or replace anything in your radio except the batteries. Care and Safety To clean the radio, use a soft cloth dampened with water. Do not use cleaners or solvents because they can harm the body of the unit and leak inside, causing permanent damage. Use a dry, lint-free cloth to clean the battery contacts. Do not submerge the unit in water. If the unit gets wet, turn it off and remove the batteries immediately. Dry the battery compartment with a soft cloth to minimize potential water damage. Leave the battery compartment cover off overnight to ensure complete drying. Do not use the radio until the unit is completely dry. Your radio might cause TV or radio interference even when it is operating properly. To determine whether your radio is causing the interference, turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference, the FCC requires that you stop using the radio. Hazardous Environments Do not operate the radio in hazardous environments. Explosion or fire may result. Do not operate the radio near unshielded electrical blasting caps. Under certain conditions, radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: "Turn off two-way radio." Construction crews often use remote control RF devices to set off explosives. WARNING! Read this information before using the radio. In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of the radio complies with the FCC guidelines and these international standards. Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines. WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following:
Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna. REGULATORY INFORMATION Hand-Held Operation (Held-to-Face) This device was evaluated for typical hand-held
(held-to-face) operations with a 1 inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face in order to comply with FCC RF exposure requirements. Body-Worn Operation This device was evaluated for body-worn operations with the supplied belt-clip accessory.
(All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines. For body worn operation, this device has been tested and meets the Industry Canada RF exposure guidelines when used with Uniden accessories supplied or designated for this product. Use of other accessories may not ensure compliance with Industry Canada RF exposure guidelines. Fonctionnement de lappareil, lorsque port sur le corps. Cet appareil a t test et sest avr conforme aux normes dIndustrie Canada et approuv pour le port sur le corps laide des accessoires Uniden inclus et conus pour cet appareil. Lutilisation d'accessoires ne respectant pas les exigences d'exposition RF dIndustrie Canada doit tre vite. FCC Compliance This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Avis de conformit la FCC : Ce dispositif a t test et savre conforme larticle 15 des rglements de la Commission fdrale des communications (FCC). Ce dispositif est soumis aux conditions suivantes: 1) Ce dispositif ne doit pas causer dinterfrences nuisibles et; 2) Il doit pouvoir supporter les parasites quil reoit, incluant les parasites pouvant nuire son fonctionnement. Tout changement ou modification non approuv expressment par la partie responsable pourrait annuler le droit lutilisateur de faire fonctionner cet quipement. IC Compliance This device complies with Industry Canada license-
exempt RSS standard(s).Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Cet appareil est conforme aux normes RSS exemptes de licences dIndustrie Canada. Son fonctionnement est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas causer dinterfrences nuisibles et 2. Cet appareil doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un fonctionnement non dsir de l'appareil. Tout changement ou modification non approuv expressment par la partie responsable pourrait annuler le droit lutilisateur de faire fonctionner cet quipement. rights which vary from state to state. This warranty . is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owners manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product and separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it.The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service C/O Saddle Creek 743 Henrietta Creek Road, Suite 100 Roanoke, TX 76262 ONE YEAR LIMITED WARRANTY Important: Save your receipt! Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is:
(A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, sub-assemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty,
(E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owners manual for this product. STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other 2019 Uniden America Corp. All rights reserved Issue 3, June 2019 Printed in China