FCC ID: AMWSX167 Portable PTT FRS Transceiver

i s o d a r y a w

-

2 S R F SX167 22 FRS Channels Long Battery Life Up to 16-mile Range*

Battery Strength Meter Roger Beep Battery Low Alert/Battery Save Call Key Last Channel Memory USB Charging NOAA Weather Radio

* Range may vary depending on environmental and/or topographical conditions. 1 3 2 4 5 7 6 8 9 10 1 Antenna 2 Call Key 6 Volume/Channel Up 7 USB (some versions; see packaging) 3 PTT (Push-to-

Talk) 8 Volume/Channel Down 4 Power/Channel Key 5 LCD 9 Microphone 10 Speaker Congratulations on your purchase of Uniden's SX167 series radio. This lightweight, palm-sized radio is a state-of-the-art device, equipped with many valuable features. Use it at sporting events, to stay in contact with family and friends, hiking, skiing, outdoors, or in a neighborhood watch for vital communication. PACKAGE CONTENTS Each radio uses 3 AAA rechargeable Ni-MH batteries, included. If your model number contains a "C,"

your radio can be charged. A micro-

USB Y charging cable is included. If your model number contains an

"H," your radio has a headset jack. Headsets are not included. Refer to the packaging for other specific contents. BATTERIES Each SX167 radio comes with 3 AAA NiMH batteries. You can also use 3 AAA Alkaline batteries (not included) . To install the batteries (NiMH or Alkaline):

1. If necessary, remove the belt clip. Press up on the belt clip latch and slide the belt clip off of the radio. 2. Remove the battery compartment door by pressing on and sliding out the compartment door. Remove the cover. 3. Install the 3 AAA batteries (NiMH included) into the battery compartment. Be certain to follow the + and symbols in the compartment. Installing the batteries incorrectly will prevent the unit from operating. 4. Replace the battery compartment door by sliding the door into place. 5. Replace the belt clip if necessary. 1. Plug one branch of the included microUSB Y-Cable into each radio's microUSB charge port. 2. Insert the other end (USB) into a USB power source (computer, phone charger, etc - not included). 3. The battery strength meter in the upper right-hand corner indicates the battery level during recharging. Notes:

Charge time may vary depending on the battery life remaining. For fastest charging, turn off the radio before charging. Do not try to recharge alkaline batteries. Doing so can create a safety hazard and/or damage the radio. If battery power is low, you cannot operate the radio even using external power. if you try to transmit while power is low, the radio will automatically turn off. Recharge or replace the batteries. USING A HEADSET For models that have a headset jack:

You can use a headset for more private communications. To use a headset, lift the rubber cover from over the headset jack, then plug in a headset (not included). USING THE RADIO In order to get the most out of your new radio, read this reference guide completely before attempting to operate it. TURNING THE RADIO ON AND ADJUSTING THE VOLUME 1. Press and hold the

/CH key to turn the radio ON. The radio tunes to the last active channel.

/CH key to 2. Press and hold the turn the radio OFF. CHARGING THE RADIO For models that recharge with rechargeable NiMH batteries installed:

Press the or keys to increase or decrease the volume level. L1 - L8 displays as you press the keys. CHANNEL OPERATION Your radio has 22 channels you can use to talk to others. In order to speak to someone, each of you must be set to the same channel. CHOOSE A CHANNEL 1. With the radio on, press

/CH key once. The current channel number flashes. 2. Use the or keys to select other channels (1 - 22). Press and hold or keys to rapidly change channels. TALK ON YOUR RADIO To talk to others using the radio:

Once you select a channel, press PTT to talk. When you finish talking, release PTT. The radio sends a roger beep at the end of your transmission so that others know you've finished talking. If the other party does not hear you, you can press CALL to send a call alert tone. AUTOMATIC POWER SAVE FEATURE Your radio has a unique circuit designed to dramatically extend the life of the batteries. If there are no transmissions or incoming calls within 2 seconds, your radio switches to the Power Save mode. The radio is still able to receive transmissions in this mode. WEATHER CHANNEL 1. With the radio on, press

/CH key twice. The weather icon displays and the radio tunes to the current weather channel. 2. Use the or keys to select other weather channels (1 - 10). SPECIFICATIONS 22 FRS CH. X-REF Channels Operating Freq. UHF 462.5500 - 467.7125 MHz Power Source Battery Life FREQUENCY CHART CH. 3 AAA Rechargeable NiMH Batteries 20 Hours typical

(5/5/90 duty cycle) X-REF FREQ

(MHz) 462.5325 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 467.6375 1 2 3 4 5 6 7 8 9 10 11 FRS 12 FRS 13 FRS 14 GMRS 11 GMRS 8 GMRS 12 GMRS 9 GMRS 13 GMRS 10 GMRS 14 GMRS 15 Note:This product is considered FRS only with 22 FRS FRS/GMRS 1 FRS/GMRS 2 FRS/GMRS 3 FRS/GMRS 4 FRS/GMRS 5 FRS/GMRS 6 FRS/GMRS 7 FRS 8 FRS 9 FRS 10 FRS 11 12 13 14 15 16 17 18 19 20 21 22 FREQ

(MHz) 467.6625 467.6875 467.7125 462.5500 462.5750 462.6000 462.6250 462.6500 462.6750 462.7000 462.7250 channels in the US market. It is considered a GMRS product in the Canadian market. MAINTENANCE TO BE SAFE AND SURE:

Never open your radios case. Never change or replace anything in your radio except the batteries. CARE AND SAFETY To clean the radio, use a soft cloth dampened with water. Do not use cleaners or solvents because they can harm the body of the unit and leak inside, causing permanent damage. Use a dry, lint-free cloth to clean the battery contacts. Do not submerge the unit in water. If the unit gets wet, turn it off and remove the batteries immediately. Dry the battery compartment with a soft cloth to minimize potential water damage. Leave the battery compartment cover off overnight to ensure complete drying. Do not use the radio until the unit is completely dry. Your radio might cause TV or radio interference even when it is operating properly. To determine whether your radio is causing the interference, turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference, the FCC requires that you stop using the radio. HAZARDOUS ENVIRONMENTS Do not operate the radio in hazardous environments. Explosion or fire may result. Do not operate the radio near unshielded electrical blasting caps. Under certain conditions, radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: "Turn off two-way radio." Construction crews often use remote control RF devices to set off explosives. WARNING! Read this information before using the radio In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of the radio complies with the FCC guidelines and these international standards. Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines RBRC INFORMATION As part of our commitment to protect the environment and conserve natural resources, Uniden voluntarily participates in an RBRC industry program to collect and recycle used Ni-MH batteries within the US. Please call 1-800-8-BATTERY for information on Ni-MH battery recycling in your area. (RBRC is a registered trademark of the Rechargeable Battery Recycling Corporation.) FCC RF EXPOSURE WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following:

Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the radio, or result in violation of FCC regulations. Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna. Body-Worn Operation This device was tested for typical body-

worn operations using the supplied belt-

clip. To maintain compliance with FCC RF exposure requirements, body-worn operations are restricted to the supplied belt-clip. For hand-held operation, the radio should be held 1 inch from the user's face. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided. For more information about RF exposure, please visit the FCC web site at www.fcc. gov. FCC PART 15 /

IC COMPLIANCE FCC PART 15 COMPLIANCE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Avis de conformit la FCC : Ce dispositif a t test et savre conforme larticle 15 des rglements de la Commission fdrale des communications (FCC). Ce dispositif est soumis aux conditions suivantes: 1) Ce dispositif ne doit pas causer dinterfrences nuisibles et; 2) Il doit pouvoir supporter les parasites quil reoit, incluant les parasites pouvant nuire son fonctionnement. Tout changement ou modification non approuv expressment par la partie responsable pourrait annuler le droit lutilisateur de faire fonctionner cet quipement. IC COMPLIANCE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Cet appareil est conforme aux normes RSS exemptes de licences dIndustrie Canada. on fonctionnement est soumis aux deux conditions suivantes :

1. Cet appareil ne doit pas causer dinterfrences nuisibles et 2. Il doit pouvoir accepter les interfrences, incluant celles pouvant nuire son fonctionnement normal. Tout changement ou modification non approuv expressment par la partie responsable pourrait annuler le droit lutilisateur de faire fonctionner cet quipement. ONE YEAR LIMITED WARRANTY Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is: (A) damaged or not maintained as reasonable or necessary,

(B) modified, altered, or used as part of any conversion kits, sub-assemblies, or any configurations not sold by Uniden,

(C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owners manual for this product. STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owners manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it.The Product should be shipped freight prepaid, by traceable means, to warrantor:

Uniden America Service C/O Saddle Creek 743 Henrietta Creek Rd., Suite 100 Roanoke, TX 76262 2019 Uniden America Corporation All rights reserved Issue 2, June 2019 Printed in China

Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167 Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167 Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167 Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167 Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167 Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167 Internal photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167

External Photos INTERTEK TESTING SERVICES Test Report Number: 16121031HKG-001 FCC ID: AMWSX167

PLB.0000.875R UNIDEN AMERICA CORP. MODEL: SX167-2CH FCC ID: AMWSX167 IC: 513C-SX167 S/N: 7O000001 Made In China 7OONREAL

-0.25mm UNIDEN AMERICA CORP. MODEL: SX167-2CH FCC ID: AMWSX167 IC: 513C-SX167 S/N: 7O000001 Made In China PLB.0000.876R UNIDEN AMERICA CORP. MODEL: SX167-3CH FCC ID: AMWSX167 IC: 513C-SX167 S/N: 7O000001 Made In China 7OONREAL

-0.25mm UNIDEN AMERICA CORP. MODEL: SX167-3CH FCC ID: AMWSX167 IC: 513C-SX167 S/N: 7O000001 Made In China PLB.0000.862R UNIDEN AMERICA CORP. MODEL: SX167 FCC ID: AMWSX167 IC: 513C-SX167 S/N: 7O000001 Made In China 7OONREAL 20.5*12.5MM UNIDEN AMERICA CORP. MODEL: SX167 FCC ID: AMWSX167 IC: 513C-SX167 S/N: 7O000001 Made In China

Uniden America Corporation 3001 Gateway Dr. Suite 130 Inving, TX 75063 817-858-3300 Fax: 817-858-3333 Uniden Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: January 21, 2019 SUBJECT: Letter of Authorization To Whom It May Concern:

We, Uniden America Corporation , hereby authorize Ben Hewson or Art Voss at Celltech Labs on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Celltech Labs on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Quality Assurance and Regulatory Manager Uniden America Corporation

Test Report Serial Number:

Test Report Date:

Project Number:

45461534 R2.0 2 August 2019 1456 Cover Letter - Class II Permissive Change Applicant:

Product Model Number / HVIN SX167-2C SX167-2CH SX167-3CH Uniden America Corporation 6225 N. State Highway 161 Suite 300 Irving, Tx, 75038, USA FCC ID:

AMWSX167 In Accordance With:

FCC 47 CFR Part 95 Subpart B Family Radio Service (FRS) Approved By:

Ben Hewson, President Celltech Labs Inc. 21-364 Lougheed Rd. Kelowna, BC, V1X 7R8 Canada Test Lab Certificate: 2470.01 IC Registration 3874A-1 FCC Registration: CA3874 This report shall not be reproduced in any form without the expressed written consent of Celltech Labs Inc. 2019 Celltech Labs Inc, Test Report S/N: 45461534 R1.0 Test Report Issue Date: 2 August 2019 To:

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: Class II Permissive Change for FCC ID: AMWSX167, FRS/GMRS to FRS Dear Examiner, This is a request for a Class II Permissive Change to reclassify a combination FRS/GMRS PTT Transceiver, FCC ID: AMWSX167, Models: SX167-2C, SX167-2CH, SX167-3CH, to an FRS only PTT Transceiver. The transceiver is identical in all aspects to that which was previously granted with the exception that the GMRS bands have been disabled. No other modifications have been made and the transceiver remains compliant to the requirements of FCC Part 95B. The Users manuals have been revised to indicate this change. If you have any further questions or concerns please do not hesitate to contact me. Thank you. Sincerely, Art Voss, P.Eng.

3001 Gateway Dr. Suite 130 Irving, TX 75063 817-858-3300 Fax: 817-858-3333 Uniden February 23, 2017 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 95 Certification FCC ID: [AMWSX167]

Request is hereby submitted by Uniden America Corporation to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and Uniden America Corporation reserves the right to discern which parties can obtain access to these information:

schematics Detailed Block diagrams Detailed Operational/Functional Description Parts List Tune up Procedures Operational Description The rationale for request for confidentiality is as follows:

This information represents intellectual property of Uniden America Corporation and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards, Al Baum Director of Engineering and Quality

Uniden America Corporation 3001 Gateway Dr. Suite 130 Irving, TX 75063 817-858-3300 Fax: 817-858-3333 uniden February 23, 2017 To whom it may concern, Label Location Justification

[FCC ID: AMWSX167 ]

Request is hereby submitted by Uniden America Corporation to request an alternative method of positively identifying the equipment, pursuant to 47 CFR 2.925/(f) of the FCC Rules. The FCC identifier for parent unit will be placed in the battery compartment and the following requirements are confirmed to meet:

a) The FCC identifier will be visible at the time of purchase, by either of the following approaches:

e Marketing the device without the battery installed, or e Providing instruction (stated on the box, user manual, or additional documentation) directing the user as to where to find the FCC label. b) The user accessible area will not require any special tools for access and the FCC label will not be placed on a removable part. The user manual has already included the FCC statements, pursuant to 47 CFR 15.19(a)(3), 15.21 and 15.105(b). lf you have questions or need further information, please contact the undersigned. Regards, Director of Engineering and Quality

Uniden America Corporation 3001 Gateway Dr. Suite 130 irving, TX 75063 817-858-3300 Fax: 817-858-3333 Uniden February 23, 2017 To whom it may concern, Letter of Authorization

|, the applicant/grantee contact of record for Uniden America Corporation do hereby authorize Intertek Testing Services (Mr. Terry Chan / Koo Wai Ip /

Kenneth Wong) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment of the FCC Rules until further notice.

| further certify that no party (as defined in 1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Al Baum Director of Engineering and Quality Uniden America Corporation