FCC ID: RII24RFMDLV01 2.4GHz 15dBm GFSK Transceiver module

MD7121-F06 2.4GHz 15dBm FSK/GFSK Transceiver 1. General Description:

The MD7121-F06 module is designed for 2.GHz ISM band with 9.43dBm output power wireless application using AMIC-COM A7121 GFSK transceiver and PA AP1110 RFIC. This module features a fully programmable frequency synthesizer by SPI. The data rate is 3Mbps. 2. Electrical Specification Specification 3.3V +/-0.1(V) 15uA @ Sleep mode

(Sleep current includes power consumption of LDO) 1.7mA @ Standby-mode 11mA @ Synthesizer mode 105mA @ Tx power = 9.43dBm 36mA @ Rx mode 2414.250 2464.875MHz 9.43dBm @ Maximum Power setting

-95dBm (Typical) @ 1M mode, Dev = 250K GFSK 20pin 1,27mm header 29(L) x 29(W) x 0.8(H) mm3 without antenna 0~50Co Remark ISM Band ISM band Typical BER <=1E-3, FSK Item Supply voltage Current consumption Frequency Transmit output power Rx sensitivity Modulation Interface PCB Dimension Operation Temperature FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Please notice that if the FCCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID:RII24RFMDLV01 IC 8102A-24RFMDLV01 any similar wording that expresses the same meaning may be used. The antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. IC Statement:

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil saccorde avec Industrie Canada licence-exempte RSS standard.

(1) cet appareil ne peut pas causer lintervention, et

(2) cet appareil doit accepter de lintervention, y compris lintervention qui peut causer lopration non dsire de. This ClassB digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe [B] est conforme la norme NMB-003 du Canada.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/1673093.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Cover Letter-Modular Approval FCC ID: RII24RFMDLV01 Data: Feb. 01, 2012 Gentlemen:

Theres an 2.4GHz 15dBm GFSK Transceiver module that would like to have your authorization as a modular approval. The specific product as below, 2.4GHz 15dBm GFSK Transceiver module, with its designed features and specified description, meets special requirements for full modular approval on FCC Public Notice DA 00-1407 Released: June 26, 2000 by cross-reference list below. Company Model Name Model Number FCC ID Unifat Technology Ltd 2.4GHz 15dBm GFSK Transceiver module KMD7121-06 RII24RFMDLV01 Requirement of Public Notice DA00 1407 1. The modular transmitter must have its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). alone in a stand 5. The modular transmitter must be tested configuration, i.e., the module must not be inside another device during testing. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. Reference to KMD7121-06 meets KMD7121-06 in chip A7121. Please The module has its own RF shielding. Please see external photographs.pdf The modular has buffered data inputs, it is integrated see schematics.pdf All power lines derived from the host device are regulated before energizing other circuits internal to the KMD7121-0 6 Please see schematics.pdf The the FCC antenna requirements. It has a u nique connector. Please see external p hotographs.pdf The KMD7121-06 was tested in a stand alone external MCU. Please see conducted setup phot ographs.pdf and spurious set The label position of KMD7121-06 is cle arly indicated. Please see the label.pdf Please notice that if the FCC identification number is not visible when the nodule is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Configuration via up a FCC Module Transmitter ID:

RII24RFMDLV01 or Contains FCC ID:

RII24RFMDLV01 The KMD7121-06 is compliant with all a pplicable FCC rules. Detail instructions are given in the Users Manual. Please see User manual.pdf The KMD7121-06 comply with applicable RF exposure requirements. Please see SAR Not Required. pdf 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4).

OINIFAT UNIFAT TECHNOLOGY LTD. Date:

Subject: Confidentiality Request for:

Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the 2012/Jan/16 Request_for Confidentiality FCC ID: RH24RFMDLV0O!

subject FCC application be held confidential. Type of Confidentiality Requested Exhibit

(_] Short Term Permanent Block Diagrams

[_] Short Term External Photos L] Short Term (] Permanent*! Internal Photos _] Short Term [XX] Permanent Operation Description/Theory of Operation

[_] Short Term [_] Permanent Parts List & Placement/BOM

[_] Short Term (_] Permanent Tune-Up Procedure

(-] Short Term &] Permanent Schematics

[_] Short Term Test Setup Photos L] Short Term {_] Permanent* _ Users Manual

*Note: (Insert Explanation as Necessary) UNIFAT Technology Ltd has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. -

Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 __ days from the date of the Grant of Equipment Authorization and prior to marketing. - This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. seit, Oho

(Print name) Sincerely,

'. The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.

? _ Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/1673104.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Label Location