UIC680 Simple Manual 2008-10-20 UIC680 SERIES Contactless Smart Card Reader Module
- RS232 & USB HID Keyboard Interface -
(Support M-Chip & qVSDC) Thank you for purchasing the UIC680 series products. The contactless smart card reader module UIC680 is mainly to support the contactless payment systems. The small footprint size of the module makes it easily to integrate to the current transaction system such as Point-of-Sale terminal, kiosk, and vending machine station as the part of the system. The module communicates with a host computer or terminal using a standard RS-232, USB or TTL interface. FEATURES
Small footprint PCB size: 50 L* 40 W (mm) without antenna board
Supports ISO 14443 type A & B standard
Supports American Express ExpressPay, MasterCard PayPassTM, Visa MSD applications
Reads/writes Philips Mifare classical contactless smart card
Provides the options for the direct coupling antenna and the remote antenna
RS232, USB 2.0 and serial TTL (optional) Interface
RS232 data pass through function
TTL F2F magnetic stripe decode data pass through (optional)
F2F decoder data emulation (optional)
Firmware upgradeable AGENCY APPROVAL
Specifications for FCC Class B, CE Class B Pb Changes or modifications are not expressly approved by the manufacturer could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment.
* Note: The external label of the enclosed module can use wording such as the following: "Contains Transmitter Module FCC ID: TFJ680LTV"
SPECIFICATIONS Standard RS232 signal level Compatible with USB 2.0 specification (optional)/TTL 5V signal level (optional) 5VDC 330mA in idle mode; 430mA in operating mode
-10 to 50 10 to 85% (non condensing) 50L x 40W mm, without antenna board Communication Power Requirements Power Consumption Operating Temperature Operating Humidity Dimensions PM076-S Revision 1 Page 1 of 2 UIC680 Simple Manual PIN ASSIGNMENT Interface J3 Pin Assignment 2008-10-20 PCB-J1 1 2 3 4 5 6 7 Signal GND TXD1 RXD1 VCC TXD2 (or USB D-) RxD2 (or USB D+) Shield 50 RF Antenna Port J2B Pin Assignment Contact number 1 2 Signal RF output GND Direct Match Antenna Port J2A Pin Assignment Contact number 1 2 3 4 Signal RX TX GND GND Signal GND RxD TxD Direction
Serial data to host
Serial data from host Serial Pass-thru or USB data Serial Pass-thru or USB data DB9 5 2 3 Shield Extension Port J1 Pin Assignment Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Signal GND GND Extended IO Extended IO GND VCC Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO Extended IO GND VCC_33 Extended IO Extended IO Extended IO Buzzer Control Signal Extended IO Extended IO Extended IO Extended IO Comment 5Vdc 3.3V PM076-S Revision 1 Page 2 of 2