all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.42 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 1.42 MiB |
BT CCD Scanner
- FCC ID: HLEMS340BT -
UsUser's Manual Version 1.1 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd Change Log. Date 2016/1/11 2016/1/22 Change Description first published version Add 1.4.2 Installing the battery Version 1.0 1.1 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. Regulatory Compliance Statements FCC Warning Statements This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. i 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. ii 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low Voltage 2006/95/EC directive. The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement RoHS Statement This device conforms to RoHS (Restriction of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitechs resellers, you shall either contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE iii 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Taiwan NCC Warning Statement
:
1. 2. 301022 1 iv 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations. The laser safety warning label required by the DHHS/IEC for the unitech products optional laser scanner module is located on the memory compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner, including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user. LED Information The unitech product contains LED indicator(s) or LED ring whose luminance is not harmful to human eyes during normal operation, user maintenance or prescribed service operations.
*LED information only applies to the products with LED components. v 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. If a battery performance decreases more than 20%, the battery is at the end of its life cycle. Stop use and ensure the battery is disposed of properly. 2. 3. The length of time that a battery lasts depends on the battery type and how the device is used. Conserve the battery life by doing the following:
Avoid fully uncharging the battery because this places additional strain on it. Several partial uncharges with frequent charges are better than a fully uncharged battery. Charging a partially charged battery does not cause harm to the unit. Keep the battery cool. Avoid hot vehicles. For prolonged storage, keep the battery at a 40% charge level. Do not leave the battery uncharged and unused for an extended period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges. 4. Protect battery life by not over or under charging the battery. 5. Please do not leave battery unused for long time without charging it. Despite unitechs safety precautions, the battery pack may begin to change shape. If so, stop using it immediately. Please check to see if you are using a proper power adapter to charge the battery or contact your service provider for service. If you cannot charge the battery after it has been idle for an extended period of time and it begins to heat up, please do not try to charge it. It may not be functional anymore. 6. 7. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by unitechs warranty policy vi 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. CAUTION!
RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.. Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0C to 40C. Charging batteries outside of the specified range could damage the batteries and shorten their life cycle. CAUTION! Do not charge batteries at a temperature lower than 0C. This will and make the batteries unstable and dangerous. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range. Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20C to 60C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature.
* The message above only applies to the usage of the removable batteries. For the products with non-removable batteries / without batteries, please refer to the specification of each product. Product Operation and Storage Notice The unitech product has applicable operation and storage temperature conditions. Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each product. vii 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Adapter Notice 1. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. 2. Please remove the power adapter when the battery is fully recharged. 3. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product. 4. Please only use the bundled power adapter or same specification of adapter to charge your unitech product. Using the wrong power adapter can damage your unitech product.
* The message above only applies to the product connected to the adapter. For the products without using the adapters, please refer to the specification of each product. Hearing Damage Warning Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following:
- the symbol of Figure 1 with a minimum height of 5 mm; and
- the following wording, or similar :
To prevent possible hearing damage, do not listen at high volume levels for long periods. Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. viii 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Worldwide Support unitechs professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below:
Taipei, Taiwan Headquarters Tel: +886-2-89121122 info@hq.ute.com E-mail:
Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian District, New Taipei City 231, Taiwan (R.O.C.) Website: http://www.ute.com China Tel: +86-59-2310-9966 info@cn.ute.com Room401C, 4F, RIHUA International Mansion, Xinfeng 3nd Road, Huoju Hi-tech District, Xiamen, Fujan , China http://cn.ute.com E-mail:
Address:
Website:
Asia & Pacific / Middle East Tel: +886-2-27911556 E-mail:
info@apac.ute.com info@india.ute.com info@mideast.ute.com Address: 4F., No. 236, ShinHu 2nd Rd., NeiHu Chiu, 114, Taipei,Taiwan Website: http://apac.ute.com / http://mideast.ute.com North America Tel: +1-714-8916400 E-mail:
Address:
Website:
info@us.ute.com / info@can.ute.com 6182 Katella Ave, Cypress, CA 90630, USA http://us.ute.com / http://can.ute.com Europe E-mail:
Address:
Tel: +31-13-4609292 info@eu.ute.com Kapitein Hatterasstraat 19, 5015 BB, Tilburg, the Netherlands http://eu.ute.com Website:
Japan E-mail:
Address:
Tel: +81-3-35232766 info@jp.ute.com Kayabacho Nagaoka Building 8F.,1-5-19 Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan http://jp.ute.com Website:
Latin America E-mail:
Address:
Tel: +52-55-5171-0528 info@latin.ute.com 17171 Park Row, Suite 210 Houston, TX 77084USA (Rep.) Website: http://latin.ute.com ix 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Warranty Policy The items covered under the unitech Limited Warranty are free from defects during normal use. The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user. x 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Table of Contents Preface...........................................................................................................i About This Manual ........................................................................................ i Regulatory Compliance Statements .............................................................. i Laser Information .........................................................................................v LED Information ........................................................................................... v Battery Notice.............................................................................................. vi Adapter Notice............................................................................................viii Hearing Damage Warning ..........................................................................viii Worldwide Support ...................................................................................... ix Warranty Policy ............................................................................................ x Chapter 1 - Overview................................................................................1 1.1 Package .................................................................................................1 1.2 Scanner & Cradle Detail.........................................................................2 1.3 Specifications .........................................................................................3 1.4 Getting Started .......................................................................................6 1.5 Battery Charging ..................................................................................10 1.6 LED Indicator / Beeper Sequence ........................................................ 11 Chapter 2 Configuration-General ....................................................13 2.1 Flow Chart............................................................................................13 2.2 Loop of Programming...........................................................................14 2.3 Factory Default Settings .......................................................................14 2.4 Main Page of Configuration..................................................................15 Chapter 3 Bar Codes & Others..........................................................16 3.1 SymboIogies Selection.........................................................................16 3.2 UPC/EAN/JAN Parameters ..................................................................18 3.3 Code 39 Parameters ............................................................................20 3.4 Code 128 Parameters ..........................................................................21 3.5 Interleave 25 Parameters .....................................................................22 3.6 Industrial 25 Parameters ......................................................................23 3.7 Matrix 25 Parameters ...........................................................................24 3.8 CODABAR/NW7 Parameters ...............................................................25 3.9 Code 93 Parameters ............................................................................27 3.10 Code 11 Parameters...........................................................................28 xi 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.11 MSI/PLESSEY Code Parameters.......................................................29 3.12 Code 2 of 6 Parameters .....................................................................30 3.13 LCD25 Parameters.............................................................................31 3.14 Telepen Parameters ...........................................................................32 3.15 GS1 Databar ......................................................................................33 3.16 Bar Code ID........................................................................................34 Chapter 4 Command Setting.............................................................37 4.1 Interface & Reading Mode Selection ....................................................37 4.2 Communication Parameters.................................................................39 4.3 Language Selection..............................................................................42 4.4 Reading Level ......................................................................................43 4.5 Accuracy...............................................................................................44 4.6 Buzzer Beep Tone ................................................................................44 4.7 Sensitivity of Continuous Reading Mode..............................................45 4.8 Reverse Output Characters..................................................................46 4.9 Setup Deletion......................................................................................46 4.10 Setup Insertion ...................................................................................49 4.11 PAN Configuration ..............................................................................52 Appendix A Numeric Bar Codes........................................................55 Appendix B ASCII Table.......................................................................56 Appendix C Function Key Table........................................................60 Appendix DNumeric Bar Codes2.......................................................61 xii 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS340B gift box. If something is missing or damaged, please contact your unitech representative. The standard package contents:
MS340B Scanner Quick Start Guide Regulatory Compliance Statements Cable Cradle Adapter Note: To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. 1 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1.2 Scanner & Cradle Detail Scan Window Trigger Cradle Scanner LED indicator Cradle LED indicator Cable connector 2 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 1.3 Specifications Optical & Performance Sensor Linear Imager Visual Indicators Beep and LED (Good read Green) System Interface USB Light Source 635 nm Visible Red LED Max. Resolution 4mil (0.1mm) PCS90%, Code39 Scan Rate Skew Angle Pitch Angle Up to 500 scans/second 60 (5) 10~65 (5) Printing Contrast Scale minimum 30%
Supports most standard 1D bar code, GS1 Databar linear and stacked Codes Decoding Depth of Field
(DOF Code39 PCS=90% ) Communication Radio Frequency Bluetooth V2.1 EDR, (smaller 10mW) Frequency Band 2.402GHz~2.480 GHz Transmission Range Up to 100m (328.08 FT.) line of sight 3 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Mechanical Dimensions Weight Switch life Electrical Input Voltage 72 x 70 x 164 mm (length x width x height) 174g (Scanner only) 1,000,000 times 5VDC Operating Power
<200mA Standby Power
< 60mA Battery Li-ion 3.7V/2600 mAh Charging time Approx. 5 hours Reads per charge Environmental Light Levels 50,000 times Max 100,000 Lux Mechanical Shock 1.5m onto concrete (scanner only) IP Rate Operating Temperature IP42 0C to 50C Storage Temperature -20C to 70C 20% to 95% non-condensing Relative Humidity Regulation Approvals CE, FCC, BSMI, VCCI, NCC, TELEC 4 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Readable Symbologies 5 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 1.4 Getting Started Please scan below barcode to set default for BT parameter. For configuration, please refer to 2.1 Flow Chart. BT Parameter Set Default 1.4.1 Scanner Mode There are three different scanner modes. Please follow the instructions below. A. Setup SPP Master Mode* (Default option) SPP Master Mode*
Please follow the below steps to setup the communication between the scanner and cradle. 1) The scanner must scan SPP Master Mode barcode to set the scanner in master mode. 2) Scan the BT MAC address code located on the bottom of the cradle. 3) When the BT MAC address code was successfully scanned, scanner will sound 3 short beeps with green LED flash once. 4) Wait approximately five seconds for completing the connection process with up-tone. 5) If successful, blue LED of scanner will slow flash and the cradle will be continued on. B. Setup SPP Slave Mode SPP Slave Mode Please follow the below steps to setup the communication between the scanner and BT application device. 1) The scanner must scan SPP Slave Mode barcode, to set the scanner in slave mode. 2) When control the BT device to search the scanner, enter pin code (default 00:00:00) to setup comport. 3) When scanner is successful connected, the scanner blue LED will also blink with up-tone. Blue LED will slowly flash to finish the setup. 6 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd C. Setup HID Slave Mode HID Slave Mode Please follow the steps to setup the communication between the scanner and Bluetooth HID profile application device. 1) The scanner must scan HID Slave Mode barcode to set the scanner in HID slave mode. 2) When control the BT device to search the scanner, enter pin code (default 00:00:00) to setup pairing. You can scan number barcode on Appendix D, Numeric Bar Codes 2 number 0~9, to setup. 3) When scanner is successful connected, scanner blue LED will also blink with up-tone. Blue LED will slowly flash to finish the setup. 7 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 1.4.2 Installing battery To install the scanner battery, please follow the instructions below. 1. Use screwdriver to loosen the screw on the bottom of the scanner and remove the battery cover. 2. Slide and position the battery, make sure the battery contacts are aligned with the contacts in the scanner.
+ -
3. Replace the battery cover and use the screwdriver to tighten the screw on the bottom of the scanner. 8 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 1.4.3 Switching Cable Before removing the cable from the cradle, it is recommended that the power on the host system is off and the power supply has been disconnected from the unit. 1. Find the small "Pin-hole" on the bottom of the cradle. (Please see the photo as below) 2. Use a bended regular paperclip and insert the tip into the hole. 3. You will hear a "click", then gently pull out the strain-relief of the cable. Pin-hole 9 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 1.5 Battery Charging The battery is in advance loaded into the compartment of the scanner and may not be fully charged before shipment. When you receive the package and use the MS340B for the first time, you will need to fully charge the battery. It takes approximately 5 hours to fully charge the battery. To chage the scanner with a cradle, please follow the instructions below. 1. Plug the adapter cable into the power socket on the bottom of cradle. 2. Plug the AC adapter cord into an electrical outlet. 3. Place the scanner in the cradle. The scanner LED will be red to indicate charging and turn green when it is fully charged. Scanner LED indicator 10 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 1.6 LED Indicator / Beeper Sequence Scanner LED Status Action/Status reading&
BeepTone LEDforBarcode Communication Good read and transmitted Green light blinks once One beep Good read and save on memory (BT disconnect) Green light blinks once One beep Good Read but Transmit Fail Green light blinks twice Two beeps Battery fully charged Solid green light No action Memory full Red light blinks twice Two beeps Low Battery warning Red light blinks once every 20 seconds In charging Solid red light One beep No action No action BT disconnect BT disconnect before sleep BT connected Setting ok Start charging Battery changed Blue light blinks twice
(continuously) No action Low beep High beep Blue light blinks once every two seconds Green light blinks once No action No action Solid red light Blue light blinks once then green light blinks twice No action 11 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Cradle LED Status Action/Status LED for Barcode reading &
Communication Good read and transmitted Green light blinks once BT disconnect (continuously) Blue light blinks twice BT connected Solid blue light 12 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Chapter 2 Configuration-General 2.1 Flow Chart
*Please scan the following barcodes for configuration Start Configuration End Configuration Abort Configuration Save Parameters 13 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 2.2 Loop of Programming The philosophy of programming parameters has been shown on the flow chart of 2.1. Basically user should :
1. Scan Start of Configuration. 2. Scan all necessary labels for parameters that meet applications. 3. Scan End of Configuration to end the programming. 4. To permanently save the settings you programmed, just scan label for Save Parameters. 5. To go back to the Default Settings, just scan label for Set All Defaults.
( Please refer to 2.4 Main Page of Configuration) 2.3 Factory Default Settings The barcode with an asterisk (*) which appears in the following chapters indicates that it is the default option for the corresponding setting. The barcode with two asterisks (**) indicate that it is the quick setting label. You can make your own settings by following the procedures in this manual. If you want to save the settings permanently, you should scan the label of Save Parameters in chapter 2.4, otherwise the settings will not be saved after the decoder power is off, and all settings will go back to previous settings. By scanning Set All Default label, the settings will go back to the factory default settings. ( Please refer to 2.4 Main Page of Configuration) 14 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 2.4 Main Page of Configuration Save Parameters Recall Stored Parameters Set All Defaults**
Start Configuration End Configuration Abort Configuration Version Information**
** : Quick Setting Label Save Parameters -The parameter settings will be saved permanently. Recall Stored Parameters - Replace the current parameters by the parameters you saved last time. Set AII Defaults - Set all the parameters to the factory default settings. Abort Configuration - Terminate current programming status. Version Information - Display the decoder version information and date code. 15 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Chapter 3 Bar Codes & Others 3.1 SymboIogies Selection UPC-A ON *
UPC-E ON *
UPC-A OFF Industrial 25 ON Industrial 25 OFF *
UPC-E OFF Matrix 25 ON Matrix 25 OFF *
EAN-13/JAN-13/ISBN-13 ON *
EAN-13/JAN-13/ISBN-13 OFF EAN-8/JAN-8 ON *
CODE 39 ON *
CODE 128 ON *
EAN-8/JAN-8 OFF CODE 39 OFF CODE 128 OFF CODABAR/NW7 ON *
CODABAR/NW7 OFF CODE 93 ON CODE 93 OFF *
CODE 11 ON CODE 11 OFF *
China Postage ON MSI/PLESSEY ON Code 2 of 6 ON China Postage OFF *
MSI/PLESSEY OFF *
Code 2 of 6 OFF *
LCD25 OFF *
Interleave 25 ON *
Interleave 25 OFF LCD25 ON 16 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Telepen ON Telepen OFF *
Reserved5 ON Reserved6 ON Reserved5 OFF *
Reserved6 OFF *
GS1 DataBar Omnidirectional OFF *
GS1 DataBar Limited OFF *
GS1 DataBar Expanded OFF *
GS1 DataBar Omnidirectional ON GS1 DataBar Limited ON GS1 DataBar Expanded ON Select All Bar Codes 17 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.2 UPC/EAN/JAN Parameters B. Supplemental Set Up Not Transmit *
Transmit 2 Code Transmit 5 Code Transmit 2&5 Code A. Reading Type UPCA=EAN13 ON ISBN-10 Enable UPCA=EAN13 OFF *
ISBN-13 Enable *
ISSN Enable ISSN Disable *
Decode with Supplement Auto discriminate Supplement *
Expand UPC-E Enable Expand UPC-E Disable *
EAN8=EAN13 Enable EAN8=EAN13 Disable *
GTIN Format Enable GTIN Format Disable *
18 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd C. Check Digit Transmission UPC-A Check Digit Transmission ON *
UPC-A Check Digit Transmission OFF UPC-E Check Digit Transmission ON *
UPC-E Check Digit Transmission OFF EAN-8 Check DigitTransmission ON *
EAN-8 Check DigitTransmission OFF EAN-13 Check Digit Transmission ON *
ISSN Check Digit Transmission ON *
EAN-13 Check Digit Transmission OFF ISSN Check Digit Transmission OFF 19 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.3 Code 39 Parameters A. Type of Code B. Check Digit Transmission C. Output Start/Stop D. Decode Asterisk Do Not Calculate Check Digit *
Character Disable *
Disable *
Calculate Check Digit & Transmit Enable Enable Italian Pharmacy/
Code 32 OFF *
Italian Pharmacy/
Code 32 ON Standard *
Calculate Check Digit & Not Transmit Full ASCII E. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 2. Numeric Bar Codes (Appendix A) 3.1st Set Complete 3. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 20 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.4 Code 128 Parameters A. Reading Type UCC/EAN-128 Disable * UCC/EAN-128 Enable Enable ]C1Code Format *
Disable ]C1Code Format B. Check Digit Transmission Calculate Check Digit& Not Transmit *
Calculate Check Digit
& Transmit Enable Code128 Group Separators(GS) *
Disable Code128 Group Separators(GS) Do Not Calculate Check Digit C. Append FNC2 OFF*
ON D. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 21 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.5 Interleave 25 Parameters B. Set Up Number of Character Even *
Odd C. Brazilian Banking Code Disable *
Enable A. Check Digit Transmission Do Not Calculate Check Digit *
Calculate Check Digit &
Transmit Calculate Check Digit &
Not Transmit D. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 22 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.6 Industrial 25 Parameters A. Reading Type IATA25 Disable *
B. Check Digit Transmission Do Not Calculate Check Digit *
IATA25 Enable Calculate Check Digit & Transmit Calculate Check Digit & Not Transmit C. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 23 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.7 Matrix 25 Parameters A. Check Digit Transmission Do Not Calculate Check Digit *
Calculate Check Digit & Transmit Calculate Check Digit & Not Transmit B. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1ST Set Begin 3. 1ST Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 24 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.8 CODABAR/NW7 Parameters A. Set Up Start/
Stop Characters Upon Transmission B. Transmission Type of Start/Stop OFF *
A/B/C/D Start *
A/B/C/D Stop *
ON A Start B Start C Start D Start A Stop B Stop C Stop D Stop 25 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd C. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 26 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.9 Code 93 Parameters A. Check Digit Transmission Calculate Check 2 Digits & Not Transmit *
Do Not Calculate Check Digit B. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable*
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 27 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.10 Code 11 Parameters A. Check Digit Transmission Do Not Calculate Check Digit *
Calculate Check 1 Digit & Transmit Calculate Check 1 Digit & Not Transmit Calculate Check 2 Digit & Transmit Calculate Check 2 Digit & Not Transmit B. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 28 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.11 MSI/PLESSEY Code Parameters A. Check Digit Transmission Calculate Check Digit & Not Transmit *
Do Not Calculate Check Digit Calculate Check Digit & Transmit B. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 29 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.12 Code 2 of 6 Parameters A. Check Digit Transmission Do Not Calculate Check Digit *
Calculate Check Digit & Transmit Calculate Check Digit & Not Transmit B. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1.1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 30 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.13 LCD25 Parameters A. Check Digit Transmission Do Not Calculate Check Digit *
Calculate Check Digit & Transmit Calculate Check Digit & Not Transmit B. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1st Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 31 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.14 Telepen Parameters A. Type of Code B. Check Digit Transmission Full ASCII Mode *
Calculate Check Digit & Not Transmit*
Compressed Numeric Mode Do Not Calculate Check Digit Calculate Check Digit & Transmit C. Set Up Code Length To set the fixed length:
1. Scan the Begin label of the desired set. 2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read. 3. Scan the Complete label of the desired set. Repeat the steps 1 - 3 to set additional lengths. Variable *
Fix Length (2 Sets Available) 1. 1st Set Begin 3. 1ST Set Complete 2. Numeric Bar Codes (Appendix A) 1. 2nd Set Begin 3. 2nd Set Complete 2. Numeric Bar Codes (Appendix A) Minimum Length 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 32 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.15 GS1 Databar A. GS1 DataBar Omnidirectional Transmit Check Digit *
Dont Transmit Check Digit B. GS1 DataBar Limited Parameters Dont Transmit Transmit Check Digit *
Check Digit Transmit Application ID *
Dont Transmit Application ID Transmit Application ID*
Dont Transmit Symbology ID *
Transmit Symbology ID Dont Transmit Symbology ID *
Dont Transmit Application ID Transmit Symbology ID C. GS1 DataBar Expanded Parameters Dont Transmit Symbology ID *
Transmit Symbology ID 33 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 3.16 Bar Code ID OFF *
ON Default With this function ON, a leading character will be added to the output string while scanning code, user may refer to the following table to know what kind of bar code is being scanned. Please refer to the table below for matching code ID of codes read in. Code Type UPC-A EAN-8 CODE 39 Interleave 25 Matrix 25 CODE 93 China Postage Code 2 of 6 Telepen GS1 DataBar Limited ID A C E G I K M P T V Code Type UPC-E EAN-13 CODE 128 Industrial 25 Codabar/NW7 CODE 11 MSI / PLESSEY LCD 25 GS1 DataBar Omnidirectional GS1 DataBar Expanded ID B D F H J L N Q U W 34 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd User Define Code ID To set the code ID:
1. Scan the symbologies label. 2. Go to the ASCII Tables in Appendix B, scan label that represents the desired code ID. Note :
User define code ID will override default value. Program will not check the conflict. It is possible to have more than two symbologies which have same code ID. UPC-A UPC-E EAN-13/JAN-13 CODE 39 CODABAR/NW7 Industrial 25 CODE 93 ChinaPostage EAN-8/JAN-8 CODE 128 Interleave 25 Matrix 25 CODE 11 MSI/PLESSEY Code 2 of 6 Telepen 35 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd LCD25 GS1 DataBar Omnidirectional ON GS1 DataBar Limited ON GS1 DataBar Expanded ON Reserved5 Reserved6 36 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Chapter 4 Command Setting 4.1 Interface & Reading Mode Selection 4.1.1 Cradle Interface Selection USB Mode *
RS232 Mode Virtual COM 4.1.2 Reading Mode Selection Trigger ON/OFF *
Good Read OFF Continuous/Trigger OFF Testing Continuous/Auto Power On Flash Flash/Auto Power On Presentation 37 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.1.3 BT Auto Connection Enable*
Disable 4.1.4 iOS Hotkey Function When enabling iOS Hotkey, you may simply double-click the trigger to toggle the iPhone/iPad Touch Keyboard. Note: This function is only available for iPhone/iPad. Enable Disable*
38 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.2 Communication Parameters 4.2.1 RS232 Communication Parameters A. Set Up BAUD Rate B. Set Up Data Bits C. Set Up Stop Bits 9600 *
8 Data Bits *
1200 2400 4800 19200 38400 7 Data Bits 1 Bit*
2 Bits 39 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd D. Set Up Parity E. Handshaking None *
RTS/CTS Disable *
Even Odd Mark Space ACK/NAK Disable *
XON/XOFF Disable *
RTS/CTS Enable ACK/NAK Enable XON/XOFF Enable 40 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.2.2 Output Characters Parameters A. Select Terminator B. Time-out Between Characters CR*
None CR +LF LF Space HT(TAB) STX-ETX 0 ms *
5 ms 10 ms 25 ms 50 ms 100 ms 200 ms 300 ms 41 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.3 Language Selection US English *
Hungarian UK English Italian Spanish French German Swedish Switzerland Janpanese Belgium Portuguese Denmark Netherlands Turkey Reserved 2 42 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.4 Reading Level The Polarity can be sent as standard with black bars high, or reversed with white bars high. Black Bars High *
White Bars High 43 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.5 Accuracy This setting is to provide the assurance of barcode consistency and to prevent the misread outcome before the data is sent to the host.Scan the barcode below to choose how many times you would like to verify the data. Note: It will cause the scanning process to slow down by choosing more than 1 time to verify the data. 1 Time *
2 Times 3 Times 4 Times 4.6 Buzzer Beep Tone High *
Medium Low Off 44 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.7 Sensitivity of Continuous Reading Mode A. Quick Setting Fast *
Slow B. Same Code Delay Reading Interval Following code sequences represent the length of time before a barcode can be rescanned at continuous and flash reading mode. The value can be defined from 1-50 and they represent 100ms to 5 seconds in100ms interval. Default value is 3 (0.3 seconds). To setup same code delay reading interval:
1. Scan the "Begin" label 2. Go the Numeric Bar Codes in Appendix A, Scan label(s),that represents the same code delay reading interval. They are ranged form 1-50.One step is represented 0.1second.So the interval is from 0.1 to 5 seconds. 3. Scan the "Complete" label Repeat the steps 1-3 to set time out of same symbol 1. Begin 3. Complete 2. Numeric Bar Codes (Appendix A) 45 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.8 Reverse Output Characters Disable *
Enable 4.9 Setup Deletion To setup the deletion of output characters:
1. Scan the label of the desired set below. 2. Scan the label of the desired symbology. 3. Go to the Numeric Bar Codes in Appendix A, scan label(s) that represents the desired position to be deleted. 4. Scan the Complete label of Character Position to be Deleted. 5. Go to the Numeric Bar Codes in Appendix A, scan label(s) that represents the number of characters to be deleted. 6. Scan the Complete label of Number of Characters to be Deleted. Repeat the steps 1 6 to set additional deletion. A. Select Deletion Set Number 1st Set 4th Set 2nd Set 5th Set 3rd Set 6th Set 46 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd B. Symbologies Selection UPC-A UPC-E EAN-13/JAN-13/ISBN-13 EAN-8/JAN-8 CODE 39 Industrial 25 Matrix 25 CODE 93 CODE 11 China Postage CODE 128 MSI/PLESSEY CODABAR/NW7 Interleave 25 Code 2 of 6 Telepen LCD25 GS1 DataBar Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded None All Codes 47 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd C. Character Position to be Deleted 1. Numeric Bar Codes
(Appendix A) 2. Complete D. Number of Characters to be Deleted 2. Complete 1. Numeric Bar Codes
(Appendix A) 48 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.10 Setup Insertion To setup the insertion of output characters :
1. Scan the label of the desired set. 2. Scan the label of the desired symbology. 3. Go to the Numeric Bar Codes in Appendix A, scan label(s) that represents the desired position to be inserted. 4. Scan the Complete label of Character Position to be Inserted. 5. Go to the ASCII Tables in Appendix B or Function Key Tables in Appendix C, scan label(s) that represents the desired characters to be inserted. Scan the Complete label of Number of Characters to be Deleted. 6. Scan the Complete label of Characters to be inserted. Repeat the steps 1 6 to set additional insertion. A. Select Insertion Set Number 1st Set 4th Set 2nd Set 5th Set 3rd Set 6th Set 49 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd B. Symbologies Selection UPC-A UPC-E EAN-13/JAN-13/ISBN-13 EAN-8/JAN-8 CODE 39 Industrial 25 Matrix 25 CODE 93 CODE 11 China Postage CODE 128 MSI/PLESSEY CODABAR/NW7 Interleave 25 Code 2 of 6 Telepen LCD25 GS1 DataBar Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded None All Codes 50 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd C. Character Position to be Inserted 2. Complete 1. Numeric Bar Codes
(Appendix A) D. Characters to be Inserted 2. Complete 1. ASCII Table
(Appendix B) 51 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.11 PAN Configuration 4.11.1 Auto Mode Auto Mode Enable *
Auto Mode Disable When Auto Mode function is enabled, and the scanner is working at out of transmission range, the scanned data will be stored to out-of-range memory. Memory size is approximately 25,000 sets of EAN13 barcode type. The all stored data will be transmitted to device when the link is reconnected, and the all data stored in out-of-range memory will be cleared. 4.11.2 Sleep Mode Sleep Mode OFF*
Sleep Mode 1 min. ON Sleep Mode10 min. ON The scanner is equipped with sleep mode function to save battery energy when the scanner is not used for 1 minute or 10 minutes. During sleep mode, all the functions and connection will be halted until pressing the trigger button. The communication with cradle or Bluetooth device will be reconnected. 52 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.11.3 Batch Mode Batch Mode OFF*
Batch Mode ON Delete Last Data **
Batch Data Read **
Batch Data Clear **
** : Quick Setting Label The function can be executed directly by scanning barcode instead of doing the general programming process. 53 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 4.11.4 Firmware Version Scanner Firmware Version**
Cradle Firmware Version**
Scanner MAC Address**
Cradle MAC Address**
** : Quick Setting Label Display the firmware version of the scanner, please scan above barcode. 54 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Appendix A Numeric Bar Codes 55 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Appendix B ASCII Table 56 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 57 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 58 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd 59 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Appendix C Function Key Table 60 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd Appendix DNumeric Bar Codes2 61 2016 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co.,Ltd
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-03-22 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2016-03-22
|
||||
1 | Applicant's complete, legal business name |
Unitech Electronics Co., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0023101058
|
||||
1 | Physical Address |
5F, No. 136, Lane 235, Pao-Chiao Rd.
|
||||
1 |
Hsin-Tien Dist., New Taipei City,, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
s******@nemko.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
HLE
|
||||
1 | Equipment Product Code |
MS340BT
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
B**** C******
|
||||
1 | Telephone Number |
886-2********
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
B******@tw.ute.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 09/18/2016 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | BT CCD Scanner | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output Power listed is conducted. Approved for portable device RF exposure condition. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Max Light Technology Co., Ltd.
|
||||
1 | Name |
J****** T********
|
||||
1 | Telephone Number |
886-2********
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
j******@mltlab.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0020000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC