Handheld Computer
- HT 1 -
User's Manual Version 0.1 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Revision History Date Change Description first published version Version 1.0 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. Regulatory Compliance Statements FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
i 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile Satellite Systems. Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and 5.7255.850 GHz band when associated with an access point (AP). FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure Statement For body contact during operation, this device has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 0.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. ii 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage 2014/35/EU directive. The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement CE RF Exposure Compliance This device meets EU requirements (2014/53/EU) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. For body-worn operation, this device has been tested and meets the ICNIRP guidelines and the European Standard EN 62209-2, for use with dedicated accessories, SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines. CE Mark Warning This equipment complies with the requirements of Directive 2014/53/EU of the European Parliament and Commission from 24 May, 2014 governing Radio and Telecommunications Equipment and mutual recognition of conformity. iii 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. RoHS Statement This device conforms to RoHS (Restriction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitechs resellers, you shall either contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE iv 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Taiwan NCC Warning Statement
:
1. 2. 301022 1 3. v 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations. The laser safety warning label required by the DHHS/IEC for the unitech products optional laser scanner module is located on the memory compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner, including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user. LED Information The unitech product contains LED indicator(s) or LED ring whose luminance is not harmful to human eyes during normal operation, user maintenance or prescribed service operations.
*LED information only applies to the products with LED components. vi 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. If a battery performance decreases more than 20%, the battery is at the end of its life cycle. Stop use and ensure the battery is disposed of properly. 2. 3. The length of time that a battery lasts depends on the battery type and how the device is used. Conserve the battery life by doing the following:
Avoid fully uncharging the battery because this places additional strain on it. Several partial uncharges with frequent charges are better than a fully uncharged battery. Charging a partially charged battery does not cause harm to the unit. Keep the battery cool. Avoid hot vehicles. For prolonged storage, keep the battery at a 40% charge level. Do not leave the battery uncharged and unused for an extended period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges. 4. Protect battery life by not over or under charging the battery. 5. Please do not leave battery unused for long time without charging it. Despite unitechs safety precautions, the battery pack may begin to change shape. If so, stop using it immediately. Please check to see if you are using a proper power adapter to charge the battery or contact your service provider for service. If you cannot charge the battery after it has been idle for an extended period of time and it begins to heat up, please do not try to charge it. It may not be functional anymore. 6. 7. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by unitechs warranty policy. vii 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. CAUTION!
RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0C to 40C. Charging batteries outside of the specified range could damage the batteries and shorten their life cycle. CAUTION! Do not charge batteries at a temperature lower than 0C. This will make the batteries unstable and dangerous. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range. CAUTION! To ensure the unit working properly, please keep all connectors away from the contaminants staying inside of them such as dust, grease, mud, and water. The negligence may cause the unit with no communication, short circuited, overheated and so on. CAUTION! If the connector is damaged, please ensure the connector is being fully repaired before use the unit to avoid causing short circuited. viii 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20C to 60C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature.
* The message above only applies to the usage of the removable batteries. For the products with non-removable batteries / without batteries, please refer to the specification of each product. Product Operation and Storage Notice The unitech product has applicable operation and storage temperature conditions. Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each product. Adapter Notice 1. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. 2. Please remove the power adapter when the battery is fully recharged. 3. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product. 4. Please only use the bundled power adapter or same specification of adapter to charge your unitech product. Using the wrong power adapter can damage your unitech product.
* The message above only applies to the product connected to the adapter. For the products without using the adapters, please refer to the specification of each product. ix 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Hearing Damage Warning Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following:
- the symbol of Figure 1 with a minimum height of 5 mm; and
- the following wording, or similar :
To prevent possible hearing damage, do not listen at high volume levels for long periods. Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. x 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Worldwide Support unitechs professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below:
Taipei, Taiwan Headquarters Tel: +886-2-89121122 info@hq.ute.com E-mail:
Europe Tel: +31-13-4609292 info@eu.ute.com E-mail:
Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian District, New Taipei City 231, Taiwan (R.O.C.) Website: http://www.ute.com Address: Kapitein Hatterasstraat 19, 5015 BB, Tilburg, the Netherlands Website: http://eu.ute.com China Tel: +86-59-2310-9966 info@cn.ute.com Room401C, 4F, RIHUA International Mansion, Xinfeng 3nd Road, Huoju Hi-tech District, Xiamen, Fujan , China http://cn.ute.com E-mail:
Address:
Website:
Japan E-mail:
Address:
Tel: +81-3-35232766 info@jp.ute.com Kayabacho Nagaoka Building 8F.,1-5-19 Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan http://jp.ute.com Website:
Asia & Pacific / Middle East Tel: +886-2-27911556 E-mail:
info@apac.ute.com info@india.ute.com info@mideast.ute.com Address: 4F., No. 236, ShinHu 2nd Rd., NeiHu Chiu, 114, Taipei,Taiwan Latin America E-mail:
Address:
Tel: +52-55-5171-0528 info@latin.ute.com 17171 Park Row, Suite 210 Houston, TX 77084USA (Rep.) Website: http://latin.ute.com Website: http://apac.ute.com / http://mideast.ute.com North America Tel: +1-714-8916400 E-mail:
Address:
Website:
info@us.ute.com / info@can.ute.com 6182 Katella Ave, Cypress, CA 90630, USA http://us.ute.com Please scan QR Code to visit us :
2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. xi Warranty Policy The following items covered under the unitech Limited Warranty are free from defects during normal use:
The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user. xii 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. Table of Contents Preface.............................................................................................................i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ vi LED Information .......................................................................................... vi Battery Notice............................................................................................. vii Adapter Notice............................................................................................. ix Hearing Damage Warning ............................................................................ x Worldwide Support ....................................................................................... x Warranty Policy .......................................................................................... xii Chapter 1 - Overview................................................................................1 1.1 Package .................................................................................................1 1.2 Product Detail.........................................................................................2 1.3 Specifications .........................................................................................4 1.4 Getting Started .......................................................................................6 1.5 Keypads Definition ...............................................................................10 1.6 HT1 Launcher.......................................................................................14 Chapter 2 Installation & Operation.................................................16 2.1 Barcode Setting....................................................................................16 2.2 HF Setting ............................................................................................19 2.3 UHF Setting..........................................................................................19 2.4 MSR Setting .........................................................................................19 2.5 WWAN Setting......................................................................................19 2.6 WLAN Setting.......................................................................................20 2.7 PAN Setting ..........................................................................................21 2.8 GPS Setting..........................................................................................22 2.9 PC Setting ............................................................................................22 2.10 Performing Factory data reset ............................................................23 2.11 Programmable Keys ...........................................................................24 Chapter 3 Introduction to Applications.........................................25 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. xiii 3.1 Scan Service ........................................................................................25 3.2 File Manager ........................................................................................29 3.3 Update Center ......................................................................................30 3.4 Sound Recorder ...................................................................................31 3.5 MoboLink..............................................................................................32 xiv 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 1.1 Package HT1 Users Manual Chapter 1 - Overview Please make sure the following contents are in the HT1 gift box. If something is missing or damaged, please contact your unitech representative. Package contents with single slot cradle HT1 Handheld Computer Battery Wrist Strap Quick Start Guide QR Code Card USB Cable Single Slot Cradle + Cradle Adapter Regulatory Compliance Statements Package contents without single slot cradle HT1 Handheld Computer Battery Wrist Strap Quick Start Guide USB Cable Plugs + Adapter Regulatory Compliance Statements 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 1 1.2 Product Detail HT1 Front View Speaker HT1 Users Manual Receiver LED Indicator Keypad Cable / Cradle connector 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 2 HT1 Rear View HT1 Users Manual Barcode scanner window Battery cover lock switch Strap hole 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 3 1.3 Specifications HT1 Users Manual System Features CPU Memory OS Languages Support Freescale iMx6 1.2GHz 1GB DDR2 4GB eMMC Android 4.4.3 English, Simplified Chines e, Traditional Chinese, Japanese, Spanish, German, French and multiple languages Display 2" TFT 240X320 LCD Keypad 10 numeric keys, scan keys, Alpha / Power (on/off) / Enter key, 4 function keys Indicator Green and Red LED located above LCD Vibrator Symbologies 2D Imager :
1D 2D All major codes PDF417, MicroPDF417, Composite, RSS,TLC-39, Datamatrix, QR code, Micro QR code,Aztec, MaxiCode, Postal Codes: US PostNet, US Planet, UK Postal, Australian Postal, Japan Postal Dutch Postal (KIX) Audio Speaker & MIC Interface USB PoGo Communication WLAN PAN Micro USB connector
(OTG interface, have USB Client and USB Host function) PoGo pin for charging IEEE 802.11 a/b/g/n Bluetooth 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 4 Power Source Battery Capacity Enclosure Weight Dimension Environmental Operating temperature Operating humidity Storage temp. Storage humidity Drop test to Concrete Environmental Sealing Vibration Magnetic field EMC Regulatory Approvals CE, FCC, BSMI, PSE HT1 Users Manual Li-ion battery Detachable with back cover all in one 1100mAh 170g 147.8(L) x 53.8(W) x 30.31(H ) 14F to 122F (-10C to 50C) 20%~85%
-22F to 158F (-30C to 70C ) 20%~85%
1.5m IP54 During operation: 0.5G, 3 to 100Hz, 1 min sweep, during 15min, 3 direction Non-operation: 1.5G, 5 to 55Hz, 1min sweep, during 120min, 3 direction Non-operation: 1.5G, 5 to 1000Hz, 1min sweep, during 15min, 3 direction 1gauss Air discharge: 16kV Direct discharge: 9KV NOTE:
Requirements in AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/
SE/CH/UK/HR. 5150MHz~5350MHz is for indoor use only. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 5 1.4 Getting Started 1.4.1 Installing the Battery 1. Turn the switch left to lock the battery cover. Turn the switch up to unlock the battery cover. HT1 Users Manual 2. You can take the battery out directly. NOTE: Please make sure the battery cover is securely closed, or you may be unable to turn ON the terminal. WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 6 HT1 Users Manual 1.4.2 Charging the Battery Before you turn on and start using this device, it is recommended that you charge the battery. If the battery has been discharged for several days, you may need to charge for several minutes before powering it on. Use only the adapter and the USB cable that came with this device to charge the battery. When the battery power is too low, make sure to use the power adapter or put into the cradle to charge. Charge with USB Connect the micro USB cable to the USB port at the bottom of HT1 and plug into your PC's USB port to simultaneously charge the HT1. Or plug the AC power adapter into the electrical outlet on the USB plug. Note: AC power adapter is included in the package without cradle. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 7 HT1 Users Manual Charge with cradle (Highly recommended ) 1. Plug the AC adapter cable into the power jack on the cradle, and then connect the AC adapter into an electrical outlet. 2. Slide the device into the cradle until it clicks in place. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 8 HT1 Users Manual 1.4.3 Turning on the terminal for the first time After you have initially charged your device for about 24 hours, the device is ready to be used. You can now start up your device. You can then set up the languages, WiFi setting, and date and time. key once, it will appear a blue symbol in Press the the status bar at the top of the screen. Then you can refer to the following table to execute the desired function or input. Please refer to 1.5.1 Using Function keys. Power-On Button Turn ON your device by pressing the power button of the terminal. 1.4.4 Checking the LED status Status LED Description Terminal Message Power Red light Green light Red light Green light Scanning Good Read Charging Fully Charged Checking the Battery Status If the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, connect PC with USB to back up your data, and then recharge your device as soon as possible. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 9 1.5 Keypads Definition HT1 Users Manual Keys Description Power key Enter key Alpha key Function key Trigger Key Escape Key
~
Alphanumeric keys Back Key 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 10 1.5.1 Using Function keys HT1 Users Manual key once, it will appear a blue symbol in the status bar at Press the the top of the screen. Then you can refer to the following table to execute the desired function or input. Keys Description Return Home Menu Programmable key F1 Programmable key F2 Programmable key F3 Left cursor key Up cursor key Right cursor key Down cursor key Google voice 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 11 HT1 Users Manual 1.5.2 Keypad Combination The following table indicates how to quickly execute useful functions using numeric keypad combination. Press and hold the the corresponding key to execute the desired function. key, and then press Key Description
+
+
+
+
+
Keypad backlight toggling Increase screen backlight brightness Decrease screen backlight brightness Scan Service 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 12 1.5.3 Using Alpha keys HT1 Users Manual key , it will appear a red symbol in the status bar at the top of Press the the screen. Then you can refer to the following table to execute the desired function or input. Key Alpha Off 0 1 2 3 4 5 6 7 8 9
#
Back Key Alpha On CAPS Off CAPS On Space Space 1 1 a, b, c, 2 A, B, C, 2 d, e, f, 3 g, h, i, 4 j, k, l, 5 D, E, F, 3 G, H, I, 4 J, K, L, 5 m, n, o, 6 M, N, O, 6 p, q, r, 7 P, Q, R, 7 t, u, v, 8 T, U, V, 8 w, x, y, z, 9 W, X, Y, Z, 9
#
*
#
*
2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 13 1.6 HT1 Launcher HT1 Users Manual HT1 launcher makes the apps bigger and clear on the screen which allows users to access any app they want more easily. Here is the introduction of the main menu. Current selected app FUNC key Enter key
/
ALPHA key Press FUNC key to move Left / right /up/down or select options on a menu. Enter or execute a command or apps on a menu. Input words or commands. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 14 1.6.1 Home Key HT1 Users Manual home key, there are items pop up from the menu such as When press Reboot, Settings and Applications. To select the related option, please press ENT key to enter the option. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 15 HT1 Users Manual Chapter 2 Installation &
Operation 2.1 Barcode Setting 1. Go to ScanService, press ENT key. 2. You are now enter the ScanService application:
There are three main items : Settings, Test and Version. 2.1.1 Settings Choose the default barcode symbologies for a different application. 2017 unitech Electronics Co., Ltd. All rights reserved. unit ech is a registered trademark of unitech Electronics Co., Ltd. 16 HT1 Users Manual 2.1.1.1 For Save / Load Settings, and Factory Default section To save data, Please go to Settings, press ENT key to enter the next section. and then select Save / Load Please select Save Settings input path - OK The save setting data is stored in File Manager. (Please see 3.2 File Manager ) 17 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.1.2 Test Scanned data information / Save / Clear all scanned data HT1 Users Manual Remove scan information Save to file 2.1.3 Version Show the recent version of ScanService 2.1.2 More Options For more options and settings, please go to
. 18 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. HT1 Users Manual 2.2 HF Setting Current model is not available. 2.3 UHF Setting Current model is not available. 2.4 MSR Setting Current model is not available. 2.5 WWAN Setting Current model is not available. 19 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.6 WLAN Setting 1. Go to Settings and press ENG key. HT1 Users Manual 2. In Wireless & networks section, Select Wi-Fi. To see available networks, turn Wi-Fi ON. And choose the available networks 3. Choose the available networks, and enter the Password and choose Connect. Please switch to ALPHA key to enter password. 20 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.7 PAN Setting 1. Go to Settings and press ENG key. HT1 Users Manual 2. In Wireless & networks section, Select Bluetooth. 3. Turn Bluetooth on to see a list of available devices. 4. To pair the available device, choose the available device. 5. When enabled, the Bluetooth icon is displayed in the status bar. 21 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.8 GPS Setting Current model is not available. 2.9 PC Setting HT1 Users Manual 1. Connect the USB charging cable to the USB port of the PC device. 2. After connecting HT1 to PC with USB, you can find a removable storage on my computer. 22 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.10 Performing Factory data reset HT1 Users Manual 1. Go to Settings and press ENG key. 2. Go to Backup & reset , select Factory data reset, it will erase all data from the device. 23 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.11 Programmable Keys HT1 Users Manual 24 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. HT1 Users Manual Chapter 3 Introduction to Applications 3.1 Scan Service 1. Go to ScanService, press ENT key. 2. You are now enter the ScanService application. Choose Test to start scanning barcodes. 25 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3. Aim the Barcode Scanner Window to the barcode and press trigger HT1 Users Manual button. Barcode scanner window Scanner trigger button 4. After scanning the barcodes, the barcode information is as shown below. Scanned data information / Save / Clear all scanned data Remove scan information Save to file 26 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. HT1 Users Manual 3.1.1 More Options For more options and settings, please go to
. Auto Scan Scan2Key Setting Save/ Load Settings Update Device Option On Screen Button Option 27 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. HT1 Users Manual 3.1.2 Multi Decode Scan Multi decode scan function allows users to scan multiple barcodes at once. 1. Go to Settings, Choose Scanner Options, press ENT key. 2. Enable Multi Decode Mode, and input the barcode decode count, back to Test screen and start multi decode scan. For video demonstration, please go to unitech youtube channel :
https://youtu.be/coJ6y0hqT9c 28 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.2 File Manager 1. Go to File Manager, press ENT key. HT1 Users Manual
: Settings
: Return to the previous page
: Main page
: Refresh
: Folder arrangement
: Folder Information 29 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.3 Update Center 1. Go to Update Center, press ENT key. HT1 Users Manual 2. To update or check the latest version of software and applications, you will need to do it manually. Refresh 30 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.4 Sound Recorder 1. Go to Sound Recorder, press ENT key. HT1 Users Manual 2. You can start recording your message. Record Stop Play 31 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.5 MoboLink HT1 Users Manual MoboLink is a software platform that helps unitech customers to remote manage their purchased devices and applications. The core of the MoboLink platform provides functionalities in the MDM (Mobile Device Management) and MAM (Mobile Application Management) domains, and then further extends into other management functions such as alert notification management and account management. 1. Go to MoboLink, press ENT key. 2. MoboLink setting is as shown below :
Menu Connection Status Settings and Setting Compliances 32 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3. Choose
, go to Settings. HT1 Users Manual Auto run on startup Show event notifications MoboLink Server URL setting 4. In the Settings section, go to MoboLink Server URL to setup MoboLink server URL. Enter MoboLink Server URL. Save the URL setting 3.5.1 More about MoboLink For detailed operation, solution and usage, please refer to MoboLink users guide. ( http://mobolink.tw.ute.com/support ) 33 2017 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.