Bluetooth Barcode Scanner
- MS852B -
User's Manual Version 1.0 Change Log Date Change Description Version MS852B Users Manual Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. All product and company names are trademarks, service marks, or registered trademarks of their respective owners. Regulatory Compliance Statements FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. i 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure Statement Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. ii 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage 2014/35/EU directive. The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement CE RF Exposure Compliance This device meets EU requirements (2014/53/EU) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. For body-worn operation, this device has been tested and meets the ICNIRP guidelines and the European Standard EN 62209-2, for use with dedicated accessories, SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines. CE Mark Warning This equipment complies with the requirements of Directive 2014/53/EU of the European Parliament and Commission from 24 May, 2014 governing Radio and Telecommunications Equipment and mutual recognition of conformity. RoHS Statement This device conforms to RoHS (Restriction of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. iii 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Waste electrical and electronic equipment (WEEE) MS852B Users Manual unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitechs resellers, you shall either contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE iv 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual Taiwan NCC Warning Statement
1. 2. 301022 1 3. v 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Laser Information MS852B Users Manual The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations. The laser safety warning label required by the DHHS/IEC for the unitech products optional laser scanner module is located on the memory compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner, including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user. LED Information The unitech product contains LED indicator(s) or LED ring whose luminance is not harmful to human eyes during normal operation, user maintenance or prescribed service operations.
*LED information only applies to the products with LED components. vi 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Battery Notice MS852B Users Manual 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. If a battery performance decreases more than 20%, the battery is at the end of its life cycle. Stop use and ensure the battery is disposed of properly. 2. 3. The length of time that a battery lasts depends on the battery type and how the device is used. Conserve the battery life by doing the following:
Avoid fully uncharging the battery because this places additional strain on it. Several partial uncharges with frequent charges are better than a fully uncharged battery. Charging a partially charged battery does not cause harm to the unit. Keep the battery cool. Avoid hot vehicles. For prolonged storage, keep the battery at a 40% charge level. Do not leave the battery uncharged and unused for an extended period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges. 4. Protect battery life by not over or under charging the battery. 5. Please do not leave battery unused for long time without charging it. Despite unitechs safety precautions, the battery pack may begin to change shape. If so, stop using it immediately. Please check to see if you are using a proper power adapter to charge the battery or contact your service provider for service. If you cannot charge the battery after it has been idle for an extended period of time and it begins to heat up, please do not try to charge it. It may not be functional anymore. 6. 7. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by your warranty. vii 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. CAUTION!
MS852B Users Manual RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0C to 40C. Charging batteries outside of the specified range could damage the batteries and shorten their life cycle. CAUTION! Do not charge batteries at a temperature lower than 0C. This will and make the batteries unstable and dangerous. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range. CAUTION! To ensure the unit working properly, please keep all connectors away from the contaminants staying inside of them such as dust, grease, mud, and water. The negligence may cause the unit with no communication, short circuited, overheated and so on. CAUTION! If the connector is damaged, please ensure the connector is being fully repaired before use the unit to avoid causing short circuited. viii 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20C to 60C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature.
* The message above only applies to the usage of the removable batteries. For the products with non-removable batteries / without batteries, please refer to the specification of each product. Product Operation and Storage Notice The unitech product has applicable operation and storage temperature conditions. Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each product. ix 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Adapter Notice MS852B Users Manual 1. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. 2. Please remove the power adapter when the battery is fully recharged. 3. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product. 4. Please only use the bundled power adapter or same specification of adapter to charge your unitech product. Using the wrong power adapter can damage your unitech product.
* The message above only applies to the product connected to the adapter. For the products without using the adapters, please refer to the specification of each product. Hearing Damage Warning Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following:
- the symbol of Figure 1 with a minimum height of 5 mm; and
- the following wording, or similar :
To prevent possible hearing damage, do not listen at high volume levels for long periods. Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. x 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Worldwide Support MS852B Users Manual unitechs professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below:
Taipei, Taiwan Headquarters Tel: +886-2-89121122 info@hq.ute.com E-mail:
Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian District, New Taipei City 231, Taiwan (R.O.C.) Website: http://www.ute.com China Tel: +86-59-2310-9966 info@cn.ute.com Room401C, 4F, RIHUA International Mansion, Xinfeng 3nd Road, Huoju Hi-tech District, Xiamen, Fujan , China http://cn.ute.com E-mail:
Address:
Website:
Asia & Pacific / Middle East Tel: +886-2-27911556 E-mail:
info@apac.ute.com info@india.ute.com info@mideast.ute.com Address: 4F., No. 236, ShinHu 2nd Rd., NeiHu Chiu, 114, Taipei,Taiwan Europe E-mail:
Address:
Tel: +31-13-4609292 info@eu.ute.com Kapitein Hatterasstraat 19, 5015 BB, Tilburg, the Netherlands http://eu.ute.com Website:
Japan E-mail:
Address:
Tel: +81-3-35232766 info@jp.ute.com Kayabacho Nagaoka Building 8F.,1-5-19 Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan http://jp.ute.com Website:
Latin America E-mail:
Address:
Tel: +52-55-5171-0528 info@latin.ute.com 17171 Park Row, Suite 210 Houston, TX 77084USA (Rep.) Website: http://latin.ute.com Website: http://apac.ute.com / http://mideast.ute.com North America Tel: +1-714-8926400 E-mail:
Address:
Website:
info@us.ute.com / info@can.ute.com 6182 Katella Ave, Cypress, CA 90630, USA http://us.ute.com Please scan QR Code to visit us :
xi 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Warranty Policy MS852B Users Manual The items covered under the unitech Limited Warranty are free from defects during normal use. The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user. xii 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual Table of Contents Preface...........................................................................................................i About This Manual ........................................................................................ i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ vi LED Information .......................................................................................... vi Battery Notice............................................................................................. vii Adapter Notice.............................................................................................. x Hearing Damage Warning ............................................................................ x Worldwide Support ...................................................................................... xi Warranty Policy .......................................................................................... xii Chapter 1 - Overview................................................................................1 1.1 Package .................................................................................................1 1.2 Product Detail.........................................................................................2 1.3 Specifications .........................................................................................4 1.4 Getting Started .......................................................................................6 1.5 Battery Charging ....................................................................................7 1.6 LED Indicator..........................................................................................8 xiii 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS852B gift box. If something is missing or damaged, please contact your unitech representative. The package contents (without cradle):
MS852B 2D Imager Barcode Scanner USB Type C Cable Quick Start Guide Regulatory Compliance Statements The package contents (with cradle):
MS852B 2D Imager Barcode Scanner Cable Cradle Quick Start Guide Regulatory Compliance Statements NOTE: The barcode with an asterisk (*) which appears in the following chapters indicates that it is the default option for the corresponding setting.
- 1 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1.2 Product Detail Scanner details MS852B Users Manual
- 2 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Cradle details MS852B Users Manual USB (Left)
- 3 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1.3 Specifications MS852B Users Manual Optical&Performance 2D 1D or 2D CMOS sensor with 640 x 400 pixel Sensor 610nm Aiming Element Illumination Hyper Red 660nm 10000 ft. candles (107,639 lux) Ambient Light 60 Skew Angle Pitch Angle Sensor 60 0 - 360 Roll Angle Optical Resolution 5.0 mil (Code 39), 6.6 mil (PDF417) Printing Contrast Scale Minimum 20%
SYMBOLOGY / X-DIM TYPICAL RANGE* Near Far 5 mil Code 39 2.0 in / 5.1 cm 6.4 in / 16.2 cm 5 mil Code 128 2.5 in / 6.3 cm 5.0 in / 12.7 cm 6.6 mil PDF417 2.5 in / 6.3 cm 6.3 in / 16.0 cm 10 mil PDF417 1.8 in / 4.5 cm* 9.0 in / 22.8 cm 13 mil 100% UPC 2.0 in / 5.0 cm* 12.5 in / 31.7 cm 20 mil Code 39 2.0 in / 5.0 cm* 19.5 in / 49.5 cm 20 mil Data Matrix 1.5 in / 3.8 cm 13.5 in /
34.3 cm 20 mil QR Code 1.5 in / 3.8 cm 11.0 in / 27.9 cm USB / RS232 Bluetooth LE V4.2 Bluetooth 2.1+EDR, Class1 Dual mode 100m ( line of sight) Depth of Field (DOF PCS=80%) Communication Host Interface supported Radio Wireless Coverage Interface/ Profile Serial Port and HID profiles
- 4 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Mechanical Scanner Dimension Cradle Dimension Weight Trigger Switch Life Functionality Symbologies MS852B Users Manual 87.8 mm x 177.7 mm x71.6 mm (L x H X W) 120.6 mm x 86.0 mm x 88.7 mm (L x H X W) 213g (without cradle) 10 million times 1D: All major symbologies and PDF417 2D:
QR Code, Data Matrix, Aztec Code, PDF417, Macro PDF417, Micro PDF417, MaxiCode, Coda block A, Codablock F, GS1Composite, Han Xin Code Postal :
Australian Post, British Post, Canadian Pos, InfoMail, Intelligent Mail Bar Code, Japanese Post, KIX (Netherlands) Post, GS1 Composite, Korea Post, Planet Code, Postal, Postnet Electrical Indicator LED & Beeper & Vibrator Battery Type Rechargeable and replaceable battery pack Battery Capacity 2850mAh Battery Charging time <6.5 hours Operating Time
>25 hours Environmental ESD Protection Mechanical Shock Operating Temperature -10C to 50C (14F to 122F) Storage Temperature Relative Humidity IP Rating RegulatoryApprovals CE, FCC, BSMI, VCCI, NCC, TELEC, BQB
-40C to +70C (-40F to +158F) 95% non-condensing IP42 Functional after 8K Contact and 15K Air 2.1M onto concrete (scanner only)
- 5 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS852B Users Manual 1.4 Getting Started How to pair devices with MS852B Please scan the barcode below to begin pairing. The scanner will show solid blue when it is pairing. BT/BLE Un-Pair / Pair How to pair devices with MS852B on the cradle If the MS852B has already paired, please scan the barcode below to un-pair it first then put it on the cradle to start pairing. BT/BLE Un-Pair / Pair There are two ways to start pairing with the cradle :
When put MS852B on the cradle, it will automatically start pairing. Scan the barcode label that appears under the cradle. The cradle will show solid blue when the pairing process has been done.
- 6 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1.5 Battery Charging MS852B Users Manual When you receive the package and use the MS852B for the first time, you will need to fully charge the battery. It takes approximately 5 hours to fully charge the battery. To charge the scanner with / without a cradle, please follow the instructions below. To charge MS852B, please connect USB type C cable to the USB port of a host PC. Connect USB type C cable with MS852B Connect USB type C cable with the cradle USB (Left )
- 7 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1.6 LED Indicator MS852B Users Manual Scanner LED indicator Description Trigger Pull No decode Wake up Decode Snapshot Snapshot is complete Power on Transmission error Entry error Defaults set Number entry expected Battery charging Battery Low < 15% (battery LED) Battery Low < 5% (battery LED) System Warning /Error Indication N/A Green Blink Blinking N/A N/A N/A Green Blink Green Blink Green Blink Solid Red Red LED blinking every 2 seconds Red LED blinking fast with all other LED indicators disabled Red LED toggling every second for 5 seconds or until trigger key pressed Green LED on BT is paired and disconnected to the host Scanner in Presentation Mode Green LED blinking every 2 seconds System busy with data scanning disabled BT is connected to host &
ready to send data Good read BT in pairing mode Green LED flashing once Blue LED toggling every second Green LED toggling every second Blue LED on
- 8 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Cradle LED indicator Description Power off Power on & Host is not connected Host is connected and BT is waiting for pairing. Host is connected and BT is paired &
ready for connection Host & BT are connected Cradle in Bootloader Mode For FW update only BT is connect & its signal is weak than normal MS852B Users Manual Indication N/A Solid Red Blue LED toggling every second Solid Green Solid Blue White LED Blue flashing quickly
- 9 - 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.