Rugged Handheld Computer
- PA726 -
User's Manual Version 0.1 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Revision History Date Change Description first published version Version 1.0 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. Regulatory Compliance Statements FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. i 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure Statement For body contact during operation, this device has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 1.0 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive. The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement ii 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. CE RF Exposure Compliance For body-worn operation, this device has been tested and meets the ICNIRP guidelines and the European Standard EN 62209-2, for use with dedicated accessories, SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines. CE Mark Warning The highest CE SAR values for the device are as follows :
0.316W/kg @ 10g (Head) 1.593W/kg @ 10g (Body) iii 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. RoHS Statement This device conforms to RoHS (Restriction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitechs resellers, you shall either contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE i 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Taiwan NCC Warning Statement
:
1. 2. 301022 1 3. ii 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations. The laser safety warning label required by the DHHS/IEC for the unitech products optional laser scanner module is located on the memory compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner, including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user. LED Information The unitech product contains LED indicator(s) or LED ring whose luminance is not harmful to human eyes during normal operation, user maintenance or prescribed service operations.
*LED information only applies to the products with LED components. iii 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. If a battery performance decreases more than 20%, the battery is at the end of its life cycle. Stop use and ensure the battery is disposed of properly. 2. 3. The length of time that a battery lasts depends on the battery type and how the device is used. Conserve the battery life by doing the following:
Avoid fully uncharging the battery because this places additional strain on it. Several partial uncharges with frequent charges are better than a fully uncharged battery. Charging a partially charged battery does not cause harm to the unit. Keep the battery cool. Avoid hot vehicles. For prolonged storage, keep the battery at a 40% charge level. Do not leave the battery uncharged and unused for an extended period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges. 4. Protect battery life by not over or under charging the battery. 5. Please do not leave battery unused for long time without charging it. Despite unitechs safety precautions, the battery pack may begin to change shape. If so, stop using it immediately. Please check to see if you are using a proper power adapter to charge the battery or contact your service provider for service. If you cannot charge the battery after it has been idle for an extended period of time and it begins to heat up, please do not try to charge it. It may not be functional anymore. 6. 7. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by unitechs warranty policy. iv 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. CAUTION!
RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0C to 40C. Charging batteries outside of the specified range could damage the batteries and shorten their life cycle. CAUTION! Do not charge batteries at a temperature lower than 0C. This will make the batteries unstable and dangerous. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range. CAUTION! To ensure the unit working properly, please keep all connectors away from the contaminants staying inside of them such as dust, grease, mud, and water. The negligence may cause the unit with no communication, short circuited, overheated and so on. CAUTION! If the connector is damaged, please ensure the connector is being fully repaired before use the unit to avoid causing short circuited. v 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20C to 60C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature.
* The message above only applies to the usage of the removable batteries. For the products with non-removable batteries / without batteries, please refer to the specification of each product. Product Operation and Storage Notice The unitech product has applicable operation and storage temperature conditions. Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each product. Adapter Notice 1. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. 2. Please remove the power adapter when the battery is fully recharged. 3. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product. 4. Please only use the bundled power adapter or same specification of adapter to charge your unitech product. Using the wrong power adapter can damage your unitech product.
* The message above only applies to the product connected to the adapter. For the products without using the adapters, please refer to the specification of each product. vi 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Hearing Damage Warning To prevent possible hearing damage, do not listen at high volume levels for long periods. vii 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Worldwide Support unitechs professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below:
Taipei, Taiwan Headquarters Tel: +886-2-89121122 info@hq.ute.com E-mail:
Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian District, New Taipei City 231, Taiwan (R.O.C.) Website: http://www.ute.com China Tel: +86-59-2310-9966 info@cn.ute.com Room401C, 4F, RIHUA International Mansion, Xinfeng 3nd Road, Huoju Hi-tech District, Xiamen, Fujan , China http://cn.ute.com E-mail:
Address:
Website:
Asia & Pacific / Middle East Tel: +886-2-27911556 E-mail:
info@apac.ute.com info@india.ute.com info@mideast.ute.com Address: 4F., No. 236, ShinHu 2nd Rd., NeiHu Chiu, 114, Taipei,Taiwan Europe Tel: +31-13-4609292 info@eu.ute.com E-mail:
Address: Kapitein Hatterasstraat 19, 5015 BB, Tilburg, the Netherlands Website: http://eu.ute.com Japan E-mail:
Address:
Tel: +81-3-35232766 info@jp.ute.com Kayabacho Nagaoka Building 8F.,1-5-19 Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan http://jp.ute.com Website:
Latin America E-mail:
Address:
Tel: +52-55-5171-0528 info@latin.ute.com 17171 Park Row, Suite 210 Houston, TX 77084USA (Rep.) Website: http://latin.ute.com Website: http://apac.ute.com / http://mideast.ute.com North America Tel: +1-714-8916400 E-mail:
Address:
Website:
info@us.ute.com / info@can.ute.com 6182 Katella Ave, Cypress, CA 90630, USA http://us.ute.com Please scan QR Code to visit us :
2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. xi Warranty Policy The following items covered under the unitech Limited Warranty are free from defects during normal use:
The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user. 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. xii Table of Contents Preface.............................................................................................................i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ iii LED Information .......................................................................................... iii Battery Notice.............................................................................................. iv Adapter Notice............................................................................................. vi Hearing Damage Warning .......................................................................... vii Worldwide Support ....................................................................................... x Warranty Policy .......................................................................................... xii Chapter 1 - Overview................................................................................1 1.1 Package .................................................................................................1 1.2 Product Detail.........................................................................................2 1.3 Specifications .........................................................................................5 1.4 Getting Started .....................................................................................12 Chapter 2 Installation & Operation.................................................18 2.1 Barcode Setting....................................................................................18 2.2 HF Setting ............................................................................................24 2.3 UHF Setting..........................................................................................25 2.4 MSR Setting .........................................................................................25 2.5 WWAN Setting......................................................................................26 2.6 WLAN Setting.......................................................................................28 2.7 PAN Setting ..........................................................................................29 2.8 GPS Setting..........................................................................................30 2.9 PC Setting ............................................................................................32 2.10 Camera Setting ..................................................................................33 2.11 Performing a Hardware Reset ............................................................38 2.12 Performing Factory data reset ............................................................39 2.13 Programmable Keys...........................................................................40 2.14 Battery Swap ......................................................................................47 Chapter 3 Introduction to Applications.........................................50 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. xiii 3.1 Scan Service ........................................................................................50 3.2 File Manager ........................................................................................55 3.3 Update Center......................................................................................56 3.4 Sound Recorder ...................................................................................57 3.5 Push to Talk..........................................................................................59 3.6 MoboLink..............................................................................................60 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. xiv PA726 Users Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the PA726 gift box. If something is missing or damaged, please contact your unitech representative. The standard package contents PA726 Terminal Battery Hand Strap QR Code Card Quick Start Guide Regulatory Compliance Statements Optional accessories 4-slot Ethernet Cradle 4-slot Terminal Charging Cradle 1-slot USB Cradle 1-slot Ethernet Cradle 4-slot Battery Charger Vehicle Charger USB Holder Cable Hand Strap with stylus loop Stylus & Coiled Strap Bumper Gun Grip Wrist-arm Mount 9H Glass Screen Protector 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 1 1.2 Product Detail PA726 Front View PA726 Users Manual Receiver 5 megapixel camera Back button Camera button Microphone Home screen button Menu button 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2 PA726 Rear View PA726 Users Manual Barcode scanner window Flash LED 8 megapixel / Autofocus camera Microphone Battery cover Knobs Speaker Cable / Cradle connector 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3 PA726 Left and Right View PA726 Users Manual Earphone Jack Volume up/down Scanner trigger button Power key Push to talk 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 4 1.3 Specifications PA726 Users Manual System Features CPU Memory Expanded slot OS Languages support MSM8953 2GHz Octa Core ARM A53 64bits 3GB SDRAM 32GB eMMC / MLC Flash
(2GB of ROM is completely independent partition that delivers stable processes and flexible programs installation.) MicroSD, up to 128GB Android 7.1 English, Simplified Chinese, Traditional Chinese, Japanese, Spanish, German, French and multiple languages Display Gorilla Glass with 5-point capacitive touch panel 4.67" Color 450 cd/m2 Brightness 720x1280 dots Color Transmissive types TFT Keypad 4 x Function key 2 x Scan trigger button Indicator 1 x LED Indicator Vibrator 1 x Power key 2 x Volume key 1 x Push To Talk key 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 5 Symbologies 1D (SE655) UPC/EAN PA726 Users Manual UPCA UPCE UPCE1 EAN8 EAN13 BooklanEAN BooklandISBNFormat DecodeUPC/EAN/JANSupplementals TransmitUPCACheckDigit TransmitUPCECheckDigit TransmitUPCE1CheckDigit UPCAPreamble UPCEPreamble UPCE1Preamble ConvertUPCEtoA ConvertUPCE1toA EAN8/JAN8Extend UCCCouponExtendedCode ISSNEAN Interleaved2of5 Code128 Code39 Code93 Code11 Discrete2of5 Codabar MSI Chinese2of5 Matrix2of5 GS1DataBar(RSS) 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 6 2D (SE4750)
(2D is only available when the 2D imager is on your device ) 2Dsymbologies PDF417 MicroPDF417 Code128Emulation DataMatrix DataMatrixInverse Maxicode QRcode MicroQR Aztec AztecInverse HanXin HanXinInverse 1Dsymbologies UPC/EAN PA726 Users Manual Interleaved2of5 Code128 Code39 Code93 Code11 Discrete2of5 Codabar MSI Chinese2of5 Matrix2of5 PostalCodes USPostnet USPlanet TransmitUSPostal CheckDigit UKPostal TransmitUKPostal CheckDigit JapanPostal AustralianPostal NetherlandsKIX Code USPS4CB/One Code/Intelligent Mail UPUFICSPostal GS1DataBar(RSS) Composite CompositeCCC CompositeCCA/B CompositeTLC39 Optional:DPM(Direct partmarked barcodes) UPCA UPCE UPCE1 EAN8 EAN13 BooklanEAN BooklandISBNFormat DecodeUPC/EAN/JANSupplementals TransmitUPCACheckDigit TransmitUPCECheckDigit TransmitUPCE1CheckDigit UPCAPreamble UPCEPreamble UPCE1Preamble ConvertUPCEtoA ConvertUPCE1toA EAN8/JAN8Extend UCCCouponExtendedCode ISSNEAN 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 7 Engines 1D 2D PA726 Users Manual SE655 :
Illumination/AIMER : LED 630 30 nm Optical Resolution : 5 mil (minimum readable bar code module size) Scan Repetition Rate : Nominally 50 scans/second Print Contrast : 20% (minimum print contrast) Ambient Light Immunity Light Source: 4845(lux) 5%
SE4750SR (Imager with laser aimer ) :
Sensor Resolution: 1280 x 960 pixels Illumination Element: 2 x Warm white LED Minimum Bar Code Print Contrast : 20%
Ambient Light: Max 107,639 lux (direct sunlight) Wavelength: 655 10 nm Beam divergence: 48.0 horizontal, 38.0 vertical Pulse duration: 1.7ms Maximum power :0.6 mW Audio Speaker , 3.5mm Audio Jack, Receiver, 2 x Microphone Regulatory Approvals CE, RoHS compliance, FCC, NCC, VCCI,CCC, BSMI Communication USB WLAN PAN WWAN RFID/HF USB 2.0 Host / Client IEEE 802.11 a/b/g/n/ac/d/h/i/k/r/v Bluetooth 4.2 GSM/GPRS/EDGE 850/900/1800/1900 MHz UMTS 850/900/1900/2100 MHz LTE FDD Band 1/2/3/4/5/7/8/20 TDD Band 38/39/40/41 DL: 150Mbps/ UL: 50Mbps 2x Micro SIM slots Frequency: 13.56MHz Tag Support: ISO15693, ISO14443A , ISO14443B Support NFC 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 8 PA726 Users Manual GPS
(Optional,availableonWWANversion) 12 x 12 mm patch antenna Support GPS / GLONASS Camera and Flash Light 16 MP CMOS sensor rear autofocus camera with LED flash light 5MP front camera External Storage Support MicroSD memory card up to 128GB Other Sensors G-sensor , Light + Proximity sensor , E-Compass, Gyroscope + 3-axis accelerometer Power Source Standard Battery Minimum: 3120mAh/3.6V, full charge should over 95% capacity Typical: 3220mAh/3.6V, full charge should over 95% capacity Extended Battery Enclosure Weight Minimum: 4660mAh/3.6V, full charge should over 95% capacity Typical: 4800mAh/3.6V, full charge should over 95% capacity Approximately 287g
(including standard battery, without hand strap) Approximately 171.3mm (L) x 29.3mm (H) x 80mm (W) Dimension Environmental Operating temperature Storage temperature Charging Temperature Relative Humidity Drop test to Concrete Environmental Sealing Vibration and Shock test Software Android 7.1 Support camera API and Camera 2 API.
-4F to 122F (-20C to 50C)
-22F to 140F (-30C to 60C) 32F to 113F (0C to 45C) 5% ~ 95% ( non-condensing ) 1.5 meter, 1.8 meter with bumper IP65 MIL-STD-810G, 514.4 process II 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 9 PA726 Users Manual Radio type / Description Transmitter Frequency Maximum Output Power GSM UMTS LTE WLAN 2.4GHz GSM900 DCS 1800 FDD 1 FDD 8 FDD 1 FDD 3 FDD 7 FDD 8 FDD 20 TDD 40 TDD 41 IEEE 802.11b IEEE 802.11g IEEE 802.11n IEEE 802.11a WLAN 5GHz IEEE 802.11n IEEE 802.11ac Bluetooth NFC Bluetooth RFID 880-915MHz 1710-1785MHz 1920-1980MHz 880-915MHz 1920-1980MHz 1710-1785 MHz 2500-2570MHz 880-915MHz 832-862MHz 2300-2400MHz 2496-2690MHz 2400-2483.5MHz 2400-2483.5MHz 2400-2483.5MHz 5180-5240MHz 5260-5320MHz 5500-5700MHz 5745-5825MHz 5180-5240MHz 5260-5320MHz 5500-5700MHz 5745-5825MHz 5180-5240MHz 5260-5320MHz 5500-5700MHz 5745-5825MHz 2400-2483.5MHz 13.56MHz 26.5.5dBm 30dBm 21.5dBm 22.5dBm 21.5dBm 22.5dBm 22dBm 22.5dBm 22.5dBm 21.5dBm 22.5dBm 16dBm 16dBm 15dBm 15dBm 15dBm 15dBm 10.5dBm 15dBm 15dBm 15dBm 10.5dBm 15dBm 15dBm 15dBm 10.5dBm 13.5dBm
<25dBuA/m 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 10 Note:
PA726 Users Manual The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. AT BE BG HR CY CZ DK EE FI FR DE EL HU IE IT LV LT LU MT NL PL PT RO SK SI ES SE UK IS LI NO CH TR 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 11 1.4 Getting Started 1.4.1 Installing the Battery 1. To loosen the two knobs on the battery cover by turning counterclockwise. And pull the two knobs up to remove the battery cover. 2. Slide and position the battery pack, making sure the battery contacts are aligned with the contacts in the compartment. 3. Use your thumb to snap the battery in place. 4. Put back the battery cover. PA726 Users Manual knobs Battery Compartment Contacts Plastic Tab 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 12 5. To tighten the two knobs on the battery cover by turning clockwise. PA726 Users Manual NOTE: After installing the battery, make sure the battery cover is securely closed, or you may be unable to turn ON the terminal. WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area. 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 13 PA726 Users Manual 1.4.2 Charging the Battery Before using the terminal for the first time, you need to charge it for about 24 hours. After that, you can charge the terminal for 4 hours to recharge the battery to full capacity. Charge the terminal using the USB charging cable or the docking station. 1. After PA726 is connected to the charging cable, push up the release buttons on the both sides of the USB charging cable to lock PA726. 2. Use USB charging cable to connect the AC adapter. 3. Plug the AC adapter cord into an electrical outlet. 1 Release Buttons Push up : Lock Push down: Unlock 3 2 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 14 PA726 Users Manual 1.4.3 Turning on the terminal for the first time After you have initially charged your device for about 24 hours, the device is ready to be used. You can now start up your device. You can then set up the languages, WiFi setting, and date and time. Power-On Button Turn ON your device by pressing the power button the terminal. on the right side of 1.4.4 Checking the LED status Terminal Status Scan Message Power LED Description Green light blinks once Successful reading Blue light blinks Message received Being charged Solid Red light Solid Green light Fully charged Checking the Battery Status If the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, connect PC with USB to back up your data, and then recharge your device as soon as possible. 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 15 PA726 Users Manual 1.4.5 Using the Micro SD/ Micro SIM Card The PA726 has Micro SD/ Micro SIM card slots inside the battery compartment. Inserting a Micro SD/ Micro SIM Card 1. To loosen the two knobs on the battery cover by turning counterclockwise. And pull the two knobs up to remove the battery cover. 2. Remove the battery cover and the main battery. 3. Now you can access the Micro SD card slot and two Micro SIM card slots. 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 16 4. Put the battery back into the battery cover. 5. Replace the battery cover. To tighten the two knobs on the battery cover by turning clockwise. PA726 Users Manual Removing the Micro SD/ Micro SIM Card 1. To loosen the two knobs on the battery cover by turning counterclockwise. 2. Remove the battery cover and the main battery. 3. Press the card in and release. The card pops out. 4. Remove the card from the slot. 5. Put the battery back into the battery cover. 6. Replace the battery cover. 7. To tighten the two knobs on the battery cover by turning clockwise. 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 17 PA726 Users Manual Chapter 2 Installation &
Operation 2.1 Barcode Setting go to APPS, and tap 1. Tap 2. You are now enter the ScanService application. There are three main ScanService. items : Settings, Test and Version. 2.1.1 Settings Tap the default barcode symbologies for a different application 18 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual For Save / Load Settings, and Factory Default section, To save data, Please tap Settings. and then tap Save / Load Please tap Save Settings input path - OK 19 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. The save setting data is stored in File Manager. (Please see 3.2 File Manager ) PA726 Users Manual To update scan service, please tap and then tap Update. 20 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.1.2 Test Scanned data information PA726 Users Manual 2 1 Tap Choose the path and filename to save the scanned data. And press OK 21 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.1.3 Version Show the recent version of ScanService. to Exit. Tab PA726 Users Manual Touch and hold anywhere inside the yellow line area until the pop up screen shows up for more settings. The recent version of ScanService 22 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 2.1.4 More Options For more options and settings, please tap
. 23 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.2 HF Setting PA726 Users Manual 1. Tap go to APPS, and tap Settings and then under Wireless
& networks, tap More 2. Tap NFC check box to Enable / disable NFC function. 3. If enable / disable NFC check box, it will also enable / disable Android Beam too. 4. Make sure that both devices are unlocked and have NFC turned on. If the other device has an Android Beam option, make sure it is also turned on. 5. Make sure that the NFC area (shaded part) of PA726 and the other phone's NFC area are close to one another. Experiment by slightly moving the phones until a connection is made. Tap the screen. 24 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.3 UHF Setting Current model is not available. 2.4 MSR Setting Current model is not available. PA726 Users Manual 25 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.5 WWAN Setting PA726 Users Manual 1. Turn off the terminal to insert the SIM card. Note : For the instruction, please refer to 1.4.5 Using the Micro SD/SIM Card. It only applies to the device which supports WWAN. 2. Turn on the terminal, 4G signal will show at the top of the screen. If you insert 3G SIM card into PA726, the icon status bar. is displayed on the 2.5.1 Mobile Network Settings 1. Tap go to APPS, and tap Settings and then under Wireless
& networks, tap More, and tap Cellular networks. Two SIM card slots 26 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2. You can have more Cellular network settings in this section. For network type, please tap Preferred network type. PA726 Users Manual 27 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.6 WLAN Setting 1. Tap go to APPS, and tap
& networks, Tap WLAN. PA726 Users Manual Settings and then under Wireless 2. To see available networks, turn Wi-Fi ON. And tap to choose the available networks. 3. Choose the available networks, and enter the Password and tap Connect. 4. If the wireless network that you want is not listed, tap + Add network to manually add it. 5. When enabled, the Wi-Fi icon is displayed on the status bar. 28 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.7 PAN Setting PA726 Users Manual Settings and then under Wireless 1. Tap go to APPS, and tap
& networks, Tap Bluetooth. 2. Tap ON / OFF to enable / disable Bluetooth (PAN). To pair the available device, turn Bluetooth ON to choose the available device. is displayed in the status bar. 3. When enabled, the Bluetooth icon When the Bluetooth device is connected, you'll see in the status bar. Normally, you can easily reconnect your device by switching on Bluetooth on PA726, and then turning on the device. However, you might have to connect manually if PA726 has been used with another Bluetooth device. 29 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.8 GPS Setting PA726 Users Manual go to APPS, and tap 1. Tap 2. Go to PERSONAL , Tap Location. Settings 30 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3. Tap ON/OFF for the permission to use your location information. PA726 Users Manual 4. Tap Mode for more location mode settings. High accuracy :
Use GPS, WLAN and cellular networks to determine location Battery saving :
Use WLAN and cellular networks to determine location Device only :
Use GPS to determine location 31 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.9 PC Setting PA726 Users Manual 1. Connect PA726 to your computer with the USB cable. Your computer will recognize it is USB charging. Release Buttons Push up : Lock Push down: Unlock 2. Slide down from top, the system will show as follow picture, then you can select File transfers. 32 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.10 Camera Setting PA726 Users Manual 1. Tap go to APPS, and tap Camera. Or use the camera button as below :
33 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 2.10.1 Camera Settings For the first time turn on, the screen will show a brief introduction about camera settings. 2.10.1.1 Scene Mode Setting 34 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.10.1.2 Camera filter effects PA726 Users Manual Scroll down for more. 35 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.10.1.3 Other settings PA726 Users Manual Camera switch Beautification mode Settings Panorama mode Record mode Camera mode 36 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.10.2 Record Settings PA726 Users Manual 37 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.11 Performing a Hardware Reset PA726 Users Manual You may have to perform a reset if the device freezes (i.e., the terminal no longer responds to the buttons or tapping on the screen). Long press Power button and Volume down button simultaneously to make the device restart the system within 20 seconds. 38 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.12 Performing Factory data reset PA726 Users Manual 1. Tap 2. Tap Backup & reset, you can reset to factory default when you select go to APPS, and tap Settings. Factory data reset, it will erase all include enterprise folder. 3. Tap RESET PHONE to start the factory data rest. 39 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 2.13 Programmable Keys The PA726s keys can be programmed for users to be able to perform different functions or applications. 2.13.1 Programming a key go to APPS, and tap 1. Tap 2. Go to SYSTEM, Tap Programmable keys, and select the keys to remap. Settings.
(ex. tab Push toTalk ) 40 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 3. Tab one of KEYCODES or APPS that lists the available functions or applications and select one shortcut to map to the key.
(ex. tab VOLUME_UP ) 4. The key is successfully mapped to a key code. 41 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 2.13.2 Enable/ Disable wakeup After the key is mapped to a key code, check the Enable wakeup checkbox to wake PA726 by pressing the programmable keys when PA726 is in sleep mode. Note: This function only applies to KEYCODES. 42 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 2.13.3 Export / Import a Programmable Key Configuration file Export file 1. Tab 2. Select Export 3. Tab OK Programmable keys exported successfully 43 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual The Programmable Key configuration can be exported to a text file or imported into PA726. Note: The configuration file (keys_config.txt) is saved in File Manager.
(For File Manager setting, please refer to 3.2 File Manager ) 44 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Import file PA726 Users Manual Before importing the file, please make sure the configuration file
(keys_config.txt) is in File Manager. 1. Tab 2. Select Import 3. Tab Ok Programmable keys imported successfully The new configuration will be applied immediately after import. 45 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Reset default 1. Tab 2. Select Reset to default PA726 Users Manual 46 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.14 Battery Swap PA726 Users Manual Please follow the steps for the battery swap. 1. Long press power botton until you see the pop up window and tap Batt swap. 2. The LED indicator will start showing solid red light. Please swap the battery after the LED red light goes off. Please do not turn on PA726 during the battery swap. 3. When the battery swap is done, you can press the power button to restart PA726 again. Note :Please see 1.4.1 Installing the Battery for more information. 47 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2.15 Split Screen PA726 Users Manual Split screen function allows you to have two apps work side by side on the same screen. Please follow the steps to enable split screen multitasking. Note: Some apps may not work with split-screen. 1. Hold Home screen button until you see the apps on the screen. 2. Drag one of these apps you would like to use, and drag it up to the screen.The bottom half of screen shows the rest of apps. 48 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3. To cancel split screen, drag the middle black bar up to the screen. PA726 Users Manual 49 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual Chapter 3 Introduction to Applications 3.1 Scan Service go to APPS, and tap 1. Tap 2. You are now enter the ScanService application. There are three main ScanService. items : Settings, Test and Version. Note : For more Scan Service settings, please refer to 2.1 Barcode Setting. 3.1.1 Settings 1. Scanned data information / Save / Clear all scanned data. Tap Test to start scanning barcodes. 50 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 2. Aim the Barcode Scan Engine to the barcode and press one of two scan trigger buttons. Barcode Scan Engine Scanner trigger button 51 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 3. After scanning the barcodes, the barcode information is as shown below. Tap Choose the path and filename to save the scanned data. 52 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. More Options PA726 Users Manual For more options and settings, please tap
. Auto Scan Scan2key Setting Device Option On Screen Button Option Save / Load Update Settings 53 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 3.1.2 Multi Decode Scan Multi decode scan function allows users to scan multiple barcodes at once. 1. Go to Settings, Choose Scanner Options 2. Enable Multi Decode Mode, and input the barcode decode count, back to Test screen and start multi decode scan. For video demonstration, please go to unitech youtube channel :
https://youtu.be/coJ6y0hqT9c 54 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.2 File Manager PA726 Users Manual 1. Tap go to APPS, and tap File Manager.
: Settings
: Return to the previous page
: Main page
: Refresh
: Folder arrangement
: Folder Information
: Solutions 55 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.3 Update Center PA726 Users Manual go to APPS, and tap 1. Tap 2. To update or check the latest version of software and applications, you will Update Center. need to do it manually. Refresh 56 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.4 Sound Recorder PA726 Users Manual 1. Tap go to APPS, and tap Sound Recorder. 2. Recording : Tap red dot to start the sound recording. 3. Save files : Tap stop button during the sound recording and choose save. Tap to check the recording file list. Recording List Record Button Stop Pause 57 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 4. Delete files : Tap to the recording file list and long press the file you choose to remove. Tap file. and press OK to delete the 58 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.5 Push to Talk PA726 Users Manual To operate push to talk, please go to Google Play store the walkie talkie apps which can support any android device. For example, Zello PTT Walkie Talkie is the most recommended walkie talkie app. to download Push to Talk 59 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3.6 MoboLink PA726 Users Manual MoboLink is a software platform that helps unitech customers to remote manage their purchased devices and applications. The core of the MoboLink platform provides functionalities in the MDM (Mobile Device Management) and MAM (Mobile Application Management) domains, and then further extends into other management functions such as alert notification management and account management. go to APPS, and tap MoboLink. 1. Tap 2. MoboLink setting is as shown below :
Menu Connection Status 60 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 3. Choose
, go to Settings. PA726 Users Manual 4. In the Settings section, go to MoboLink Server URL to setup MoboLink server URL. Enter MoboLink Server URL. Save the URL setting 61 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. PA726 Users Manual 3.5.1 More about MoboLink For detailed operation, solution and usage, please refer to MoboLink users guide. ( http://mobolink.tw.ute.com/support ) 62 2018 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.