unitech PA600 Phone Edition Users Manual 400646G Version 1.0 Preface About This Manual This manual explains how to install, operate and maintain the PA600 II Rugged Mobile Computer. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or infor-
mation storage and retrieval systems. The material in this manual is subject to change without notice. Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech global website address: http:\\www.unitech-adc.com Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. unitech is a member of Oracle Embedded Software Licensing Program. Regulatory Compliance Statements FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. i Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 2. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the follow-
ing two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. European Conformity Statement Declaration of Conformity with Regard to the R&TTE 1999/5/EC and EMC 89/336/
EEC directives. Taiwan NCC Warning Statement
(NCC) (930322) NCC ii About This Manual Laser Information The unitech PA600 II series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The PA600 II series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or during prescribed service operations. The laser safety warning label required by the DHHS/IEC for the PA600 II series's optional laser scanner module is located on the memory compartment cover, on the back of the unit. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, and magnifying glasses. This does not include eye glasses worn by the user. Battery Notices This unit is equipped with a battery pack and backup battery. Both batteries will dis-
charge after an extended period of not being used. When both batteries are discharged, recharge the unit for 16 hours in order to fully charge the main battery and backup battery. There are two ways to recharge PA600 II:
1. Plug the USB charging cable to the PA600 II and plug the 5V/3A AC-DC adapter to the power jack of the USB charging cable. 2. Place the PA600 II into the docking station and plug the 5V/3A AC-DC adapter to the power jack of the docking station. For more details, refer to page 8, Charging the Battery. If the main battery is removed, the backup battery ensures the data on SDRAM is safe for up to 2 hours. To prevent data loss, do not leave the PA600 II uncharged with the main battery removed for an extended period. Battery charge notice It is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is most efficient at normal room tempera-
ture or slightly cooler. It is essential that you charge batteries within the stated range of 10C to 45C. Charging batteries outside of the specified range could damage the bat-
teries and shorten their charging life cycle. iii Storage and safety notice Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at tempera-
tures between -20C to 60C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room tempera-
ture. iv Table of Contents Preface About This Manual i Regulatory Compliance Statements ............................................................................. i FCC Warning Statement.......................................................................................................... i FCC Label Statement .............................................................................................................. ii Canadian Compliance Statement............................................................................................ ii European Conformity Statement ............................................................................................. ii Laser Information ................................................................................................................ iii Battery Notices ..................................................................................................................... iii Battery charge notice.............................................................................................................. iii Storage and safety notice....................................................................................................... iv Chapter 1 Getting Started 1 Introducing the PA600 II ................................................................................................... 1 Features................................................................................................................................... 2 Package Contents ............................................................................................................... 3 A Tour of the PA600 II........................................................................................................ 3 Front Left View........................................................................................................................ 4 Back View............................................................................................................................... 5 Getting Started...................................................................................................................... 6 Installing the Battery ............................................................................................................... 6 Charging the Battery............................................................................................................... 8 Charging the Battery using the USB Cable ....................................................................... 8 Charging the Battery with the Docking Station .................................................................. 9 Checking the Battery Status .............................................................................................. 9 Connecting the PA600 II to a PC.......................................................................................... 10 Turning the PA600 II on for the First Time............................................................................ 11 Powering On.................................................................................................................... 11 Calibrating the PA600 II Screen ...................................................................................... 12 Chapter 2 Using the Hardware 14 Keypads and Function Buttons................................................................................... 14 Adjusting the Screen Brightness................................................................................ 16 Using the Stylus ................................................................................................................. 16 Using the SD/MMC memory card ................................................................................ 17 Inserting a Storage Card ................................................................................................. 17 Removing a Storage Card ............................................................................................... 17 Using the Laser Scanner ................................................................................................ 18 Using the SIM Card ........................................................................................................... 19 Inserting the SIM Card..................................................................................................... 19 v Using the Phone................................................................................................................. 20 Making a Call Using the Phone Keypad ............................................................................... 21 Using the Contact List........................................................................................................... 21 Using the Speed Dial............................................................................................................ 22 Customizing the Phone Settings........................................................................................... 22 Chapter 3 Getting Connected 23 Establishing Device-PC Connection.......................................................................... 23 Installing Microsoft ActiveSync ............................................................................................. 23 Connecting the Device to Your Computer ............................................................................ 26 Synchronizing with Your Computer........................................................................... 27 Connection options............................................................................................................... 27 USB Connection .............................................................................................................. 27 Bluetooth Connection ...................................................................................................... 27 GPRS Connection ........................................................................................................... 30 WiFi Connection .............................................................................................................. 31 Synchronizing Information ............................................................................................ 35 Synchronization Options....................................................................................................... 35 Using ActiveSync to Exchange Files ........................................................................ 35 Chapter 4 Barcode Scanner Programs 37 Scanner Setting.................................................................................................................. 37 Scan2Key .............................................................................................................................. 37 Barcode Symbologies........................................................................................................... 38 Chapter 5 Advanced Settings 39 Adjusting Settings............................................................................................................. 39 Checking the Main and Backup Battery Status..................................................... 40 Extending Battery Life..................................................................................................... 41 Changing the Automatic Power Settings .............................................................................. 41 Adjusting Backlight Setting ................................................................................................... 42 Viewing Flash Memory Files ......................................................................................... 43 Performing a hardware reset ........................................................................................ 44 Performing a Warm Boot ...................................................................................................... 44 Performing a Cold Boot ........................................................................................................ 45 Performing a Clean Boot ...................................................................................................... 46 Appendix System Specifications 47 vi Chapter 1 Getting Started Introducing the PA600 II Thank you for purchasing the PA600 II Rugged Mobile Computer. Your PA600 II was designed for users who need a compact and durable PDA for data collection and real time transactions. The PA600 II is a rugged, compact and lightweight palm-size com-
puter using the Windows Mobile 5.0 operating system, and incorpo-
rating an integral bar code scanning laser device, cell phone function, color LCD with touchscreen, keypad, and wireless com-
munication capability. It provides users with a standard Windows-
based environment for customizing and operating the device. To reduce TCO, the PA600 II is sealed to meet IP64 standards and has undergone multiple drop tests to prevent downtime. 1 Chapter 1 Getting Started Features Powerful system Audio MIC Speaker Headset Connector Receiver Wireless connectivity 802.11b/g with diversity antenna Bluetooth wireless technology Expansion slot Secure Digital (SD) card slot (sup-
ports SDHC up to 4G) Battery life Operation time: typical 5 hours
(with Wifi), average 9 hours (w/o Wifi) Charging time: under 5 hours Embedded backup battery cell User-friendly interface Quick launch hot keys for enabling backlight, calibration, phone calls, software keyboard, and other device management tasks Trigger keys for barcode scanning Microsoft Windows MobileTM 5.0 operating system Intel PXA270 processor with speed of up to 624 MHz System memory 128 MB SDRAM 320 MB Flash ROM Display 3.5-inch QVGA TFT-LCD with touch screen and backlight 240 x 320 resolution Barcode scanner Built-in laser scan engine Built-in vibrator for scanning indi-
cation Symbol SE950 support Unitech Hamster barcode decoder Communication USB Host & Client Bluetooth 2.0 + EDR
(supports Bluetooth Printer, Bluetooth Modem, Bluetooth ActiveSync) eGPRS Siemens MC75 Radio Module, quad-band GSM 850/900/
1800/1900 MHz EDGE Multislot Class 10 GPRS Multislot Class 12 GSM Release 99 2 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Package Contents Chapter 1 Getting Started After opening the box, ensure the following accessories for the PA600 II are present:
PA600 II Terminal AC Adapter with universal plugs Battery Pack Stylus USB Charging Cables CD-ROM Quick Reference Guide If anything is missing or appear damaged in any way, contact your dealer. A Tour of the PA600 II The following sections describe the main components and features of the PA600 II. 3 Chapter 1 Getting Started Front Left View 8 1 2 7 3 6 5 No. Component Status indicator 1. Description Indicates the battery charging and barcode scanning status. 4 Green - Battery is fully charged, or barcode scanning process is completed without error. Red - Battery is charging, barcode scanner is fired/
activated. Yellow - GPRS is on Blue - Bluetooth is on Press to activate the barcode laser scanner. If the device is off, press this button to turn it on. Alternatively, when the unit is on, this key must be pressed and held down for about three seconds in order to turn the device off. Enables you to record voice audio. Connects your device to a USB charging/
communication cable. This USB cable connects to the computers USB port and accepts the 5V AC adapter to provide power to the PA600 II. This unit can simultaneously recharge and perform an ActiveSync operation. You can also use it to connect peripheral hardware, such as a docking station, to your device. This port can also support USB and RS232 hosting for devices such as a USB or RS232 scanner, keyboard, or USB memory key. Keypad interface for controlling the PA600 II. See Keypads and Function Buttons on page 14 for more information. Left scanner trigger button Power button Microphone Universal connector Keypad LCD touch screen Displays the applications and data stored on your device. It Speaker is touch-sensitive and responds to the stylus or finger. Enables you to hear audio from the PA600 II. 2. 3. 4. 5. 6. 7. 8. 4 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started Back View 9 10 11 12 13 14 15 16 No. Component 9. Battery compartment 10. Battery compartment release latch 11. Reset button 12. Handstrap 13. Speaker 14. Stylus 15. Strap holder 16. Memory card slot 17. Barcode scanner window 17 Description Houses the removable and rechargeable 3.7 V, 2200 mAH battery pack Opens the battery compartment. Press the end of the stylus into the button to reset your device. Enables you to securely hold the PA600 II while using it. Enables you to hear audio from the PA600 II. Enables you to interact with the operating system. To use the stylus, remove it from its holder and hold it the same way as you hold a pen or pencil. Attachment location for holding hand strap, carrying strap, and stylus. Accommodates Secure Digital (SD) memory cards and can serve as an SDIO port. Scan barcodes window where the laser pass through. 5 Chapter 1 Getting Started Getting Started This section explains how to install and charge the battery, how to check battery sta-
tus, how to turn on the PA600 II, and how to calibrate the screen. Installing the Battery WARNING! There is a risk of fire and burns if the battery pack is handled improp-
erly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area. A backup battery cell is embedded into your device to prevent data loss in instances when the removable battery pack is removed or completely discharged. This backup battery cell will keep the data and system setting for up to 6 hours if the main battery is removed. NOTE:
To enable the internal battery cell to provide backup power supply, charge your device with the main battery pack for at least 16 hours. 1. Open the battery compartment by pushing the latch in the direction of the arrow and lifting up. The battery compartment is displayed:
Compartment contacts Plastic battery tab Battery hook NOTE:
The plastic battery tab makes it easy to remove the battery. 6 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. 2. Locate the backup battery switch and turn it on. Chapter 1 Getting Started Backup battery switch 3. Position the battery pack, making sure the battery contacts are aligned with the contacts in the compartment and the battery is placed on top of the plastic tab, as shown in the following illustration. Contacts Plastic tab 4. Slide the battery pack into the battery bay while simultaneously pulling the bat-
tery hook until the battery clicks into place. Battery hook 5. Replace the battery compartment cover. 7 Chapter 1 Getting Started Charging the Battery Before using the PA600 II for the first time, you need to charge it for about 16 hours. After that, you can charge the PA600 II 4 hours to recharge the battery to full capacity. Charge the PA600 II using the USB charging cable or the docking station. CAUTION! Operating the PA600 II for the first time without the AC adapter, and without fully charging the backup battery may result in loss of data stored in RAM memory. When the main battery is removed, the backup battery retains RAM data in memory for 2 hours, please charge the battery for the period to avoid the data loss in RAM mem-
ory. NOTE:
Turn the backup battery switch on before charging the battery. Data you entered may not be properly stored until the built-in backup battery has been adequately charged. Charging the Battery using the USB Cable 1. Press and hold the connector button on the USB charging cable and connect it to the PA600 II (1). 2. Plug the AC adapter cable into the power jack on the USB charging cable (2). 3. Connect the AC adapter into an electrical outlet (3). 2 3 1 8 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Charging the Battery with the Docking Station 1. Plug the AC adapter cable into the power jack on the docking station, then con-
nect the AC adapter into an electrical outlet. Chapter 1 Getting Started 2. Slide the device into the docking station until it clicks into place. 3. The connection is secure when the bottom edge of the device is aligned with the docking station, and the LED indicator on the device lights up red. LED Status PA600 II Docking Station LED Solid Red Solid Green Power LED Charging LED:
Sync LED Meaning Charging Charging complete Power is on Charging (For spare battery only) Synchronization is taking place Checking the Battery Status If the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, perform an Active-
Sync operation to back up your data, then recharge your device as soon as possible. If the battery level reaches low status, the device will enter a sleep mode and cannot be powered up until the battery is charged. Windows Mobile 5.0 devices will retain installed applications and data when the main battery is completely drained for extended periods of time.e 9 Chapter 1 Getting Started Connecting the PA600 II to a PC Use the USB cable to connect the PA600 II to a PC, in order to use with ActiveSync. 1. Press and hold the connector button on the USB charging cable and connect it to the PA600 II (1). 2. Plug the USB connector into the USB port on the PC and connect the AC adapter into the USB connector (2). 3. Connect the AC adapter into an electrical outlet (3). 2 3 1 10 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started Turning the PA600 II on for the First Time After you have initially charged your device for about 16 hours, the device is ready to be used. You can now start up your device where youll calibrate the display, learn some basic stylus usage, and set up the system time zone, date and time. Powering On 1. Turn on your device by pressing the power button on the front panel. NOTE: The PA600 II screen ships with a protective plastic film. You may remove this if desired by peeling from one corner. The screen will be more susceptible to scratch-
ing without the film, but will be more readable. 2. The unitech PA600 II welcome screen appears for a moment fol-
lowed by the Windows Mobile screen. Power Button Ls ESC FUNC ghi pqrs key 1 4 7 ALPHA abc Rs jkl tuv 3 6 9
. 2 5 8 0 def mno wxyz TAB OK ENTER 11 Chapter 1 Getting Started Calibrating the PA600 II Screen The calibrate screen automatically appears when the unit is powered-on for the first time or after the system is reset. To calibrate the screen at any time, follow these instructions. 1. Tap Start Settings, and then switch to System tab. 2. Tap the Screen icon. Or Press Func key and ESC key simultaneously. The Screen Settings window appears. This Window enables you to customize the screen settings. 3. Tap Align Screen to calibrate the screen. The align screen window appears. 4. Tap the cross hair firmly and accurately. 12 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. The cross hair moves to the next location. Chapter 1 Getting Started 5. Continue tapping the cross hairs until the screen has been calibrated. 13 Chapter 2 Using the Hardware Keypads and Function Buttons The keypad enables you to both enter information and interact with the PDA operating system and also operate secondary functions using the function button. When the green function button is pressed, the green icon functions on the keypad become available. When the Function button an icon appears in the operating system:
Function activated icon is pressed, The following table describes the keypad keys. Key Main Function Talk/Send Alpha End Secondary Function Opens Phone screen to make a call or send a message Enables/ disables secondary function keys Exits Phone screen or ends a call Turns the PA600 II on and off. 14 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 2 Using the Hardware Key Main Function Number 1 Secondary Function Left soft key - activates function above in LCD screen. Alphanumeric 2, a, b, c Up navigation key Alphanumeric 3, d, e, f Right soft key - activates function above in LCD screen. Tab Windows key opens Start menu Back space Escape key Alphanumeric 4, g, h, i Left navigation key Alphanumeric 5, j, k, l Alphanumeric 6, m, n, o Right navigation key Alphanumeric 7, p, q, r, s Decreases screen brightness Alphanumeric 8, t, u, v Down navigation key Alphanumeric 9, w, x, y, z Increases screen brightness Asterisk Illuminates keypad Number 0, space Period Enter key Pound OK 15 Chapter 2 Using the Hardware Adjusting the Screen Brightness Adjust the screen brightness by pressing the Function button to enable the soft keys and pressing the 7 (decrease bright-
ness) or 9 (increase brightness) buttons. Function Button Decrease Brightness Ls ESC FUNC ghi pqrs key 1 4 7 ALPHA abc Rs jkl tuv 3 6 9
. 2 5 8 0 def mno wxyz TAB OK ENTER Increase Brightness Using the Stylus CAUTION! Never use anything other than the PA600 II stylus on the screen. Oth-
erwise this could cause a permanent damage. 1. Remove the stylus from its holder. 2. Hold the stylus as you hold a pencil. 3. To make a choice from a menu, lightly tap the tip of the stylus on that choice. 4. To write data into a field on a form, use the stylus to print the letters or numbers. Use very light pressure. 16 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Using the SD/MMC memory card Chapter 2 Using the Hardware Your device has an expansion slot compatible with a range of SD and MMC storage cards, which are primarily used to back up or transfer files and data. The slot also sup-
ports SDIO cards for added connectivity options. Inserting a Storage Card 1. Remove the four screws from the SD compartment cover and remove the cover. 2. Insert the SD card with the notched corner as shown by the icon on the case. 3. Replace the SD compartment cover and the four compartment screws. Removing a Storage Card 1. Remove the four screws from the SD compartment cover and remove the cover. 2. Press the card in and release. The card pops out. 3. Remove the card from the slot. 17 Chapter 2 Using the Hardware Using the Laser Scanner The PA600 II has an integrated laser scanner which reads all major bar code labels with excellent performance. NOTE:
Scanning software must be enabled in order to operate the scanner. This can be a user-loaded application or a pre-loaded utility such as Scanner Setting and Scan2Key. Scan button Activate the laser scanner by pressing either one of the trigger keys located on the left and right side of the unit. The PA600 II has a built-in Scanner Setting utility that allows you to test the devices barcode scan function. 1. To launch Scanner Settings, tap Start Settings, and then switch to System tab. Tab the Scanner icon. 2. The Scanner Control Panel opens. From here you can configure barcode scanner parameters such as enabling or disabling barcode symbologies, setting data transmission options, configuring magnetic and proximity reading options, and setting power management options. 18 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 2 Using the Hardware 3. To test the barcode scanner, tap the Test tab. 4. Tap Tools 5. Tap Enable Scan 6. To perform auto scan, Tap Tools Auto Scan Start Auto- Scan 7. Choose Interval: 3 secs 8. Tap: Start 9. Laser scans every 3 seconds and barcode is scanned automatically. 10. Tap Tools Auto-Scan Stop Auto-
Scan. Using the SIM Card The PA600 II has a slot for GPRS SIM card. It is placed inside the battery compart-
ment. Inserting the SIM Card 1. Take out the battery cover and the main battery. Insert the SIM card with the notched corner as shown in the picture below. NOTE:
The chip of the SIM card should face upwards. 2. Push the SIM card to the end until you hear a click. Push the lock to the right to lock the card by stylus. 19 Chapter 2 Using the Hardware Using the Phone The PA600 II has an integrated phone keypad, which allows you to make, receive, and send messages via the built-in module. NOTE: Make sure you insert the SIM card properly. To open the Phone screen, do one of the following. 1. Tap Phone on the bottom left corner of the screen. 2. Press Talk/Send button. Press End button when you want to exit the Phone screen. Talk/Send button End button Ls ESC FUNC ghi pqrs key 1 4 7 ALPHA abc Rs jkl tuv 3 6 9
. 2 5 8 0 def mno wxyz TAB OK ENTER The Phone screen opens. From here you can manage the contact list, create speed dials, messages, notes, and customize phone settings. NOTE:
If you SIM card is protected by a PIN code, input the password before you can use the phone. Tap the antenna signal icon on the upper right corner of the screen. Tap Wireless Manager and turn on phone function. Antenna signal icon Signal Description Phone keypad Phone service searching No signal is available. Strongest signal strength More bars you have, the stronger signal you have. No phone service provided. Phone function is turned off. Tap the antenna signal icon and turn on phone function in the Wireless Manager. 20 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 2 Using the Hardware Speaker icon Tap the speaker icon on the upper right corner of the screen. You can adjust the device/ phone vol-
ume by moving the sliders and change the ring volume by tapping On, Vibrate, or Off. Making a Call Using the Phone Keypad 1. Tap Phone or press Talk/Send button. 2. Enter the desired phone numbers. 3. Tap the Talk button on the Phone screen. 4. When the call connects, you can tap Hold to place the first number on hold. 5. Enter the second phone numbers and tap Talk again. 6. Tap Swap to switch between calls. 7. Tap End or press End button to stop dialing or end the call. Using the Contact List 1. Tap Contacts on the bottom left corner of the Phone screen. 2. Tap New on the bottom left corner of the contact list, you can add a new contact. 3. Tap a contact, you can edit the contact info. 4. Tap and hold on a contact, a menu appears. You can send e-mail/ text mes-
sage to the contact, add this contact to speed dial list, and so on. 21 Chapter 2 Using the Hardware Using the Speed Dial 1. Tap Speed Dial on the Phone keypad. 2. Tap Menu, and select New. 3. Select a contact in your contact list by tap-
ping the desired contact. 4. Assign an available location for the new speed dial entry. Tap OK, and then OK to exit the speed dial list. NOTE:
The first speed dial location is reserved for voice mail. To make speed dial call, do one of the following. 1. Tap and hold the speed dial location number assigned to a contact on the Phone keypad. 2. Tap Speed Dial on the Phone keypad, and tap the location number of the desired speed dial entry. Location number Customizing the Phone Settings Tap Menu, and select Options, you can change the default phone settings, including ring sound, keypad sound, call barring, call forwarding, call waiting, mobile phone net-
work, etc. 22 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected Establishing Device-PC Connection Installing Microsoft ActiveSync In order to exchange data between your computer and PA600 II, Microsoft ActiveSync must be installed on your computer. Use the USB charging cable that comes with your device to connect the device to your computer. NOTE:
If you have a previous version of the Microsoft ActiveSync installed in your computer, uninstall it first before installing the latest version of Microsoft ActiveSync. To install Microsoft ActiveSync on your computer:
1. Close any open programs, including those that run at startup, and disable any virus-scanning software. 2. Download the ActiveSync software from the Microsoft ActiveSync Download page at http://www.microsoft.com/windowsmobile/downloads/activesync42.mspx. 3. Browse the location of the downloaded file, and double-click it. The installation wizard begins. 23 Chapter 3 Getting Connected 4. Click Next. You are prompted to read the End User License Agreement (EULA). 5. Accept the license agreement terms and click Next. You are prompted for user information. 6. Type the user name and organization and click Next. You are prompted for the destination folder. 24 Copyright 2008 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected 7. Select a drive to install the program and click Next. The installation wizard has gathered the information it needs to install Active-
Sync and prompts you to begin the installation. 8. Click Install. The program begin the installation After the program has finished installing you see the following screen. 25