Comcast Platco TV Remote 2020
Comcast Quick Start Guide
ACTIVATING RF
QuickSet
This product shall support the following features:
Auto Setup
Manual Setup
Optimized Setup Maps (OSM)
The following are descriptions of the Quickset features:
Auto Setup: Quickset allows for auto setup of the RCU by identifying devices connected through the
HDMI network. The RCU is programmed automatically over the RF link.
Manual Setup: Quickset allows for manual selection of a Brand for programming of devices without
having to go through Auto Detection and Programming. The RCU is programmed automatically over the
RF link.
Optimized Setup Maps: OSM assists the user with a UI flow to program a TV or Audio device in the
RCU. After the user selects brand through the UI, the RCU software and Quickset allows for the testing of
functions and by the user. The RCU is programmed over the RF link after the appropriate feedback is
observed by the user.
o GREEN led blink every 250ms for duration of advertising (10 seconds)
o Press and hold DIGIT 1 + DIGIT 3 for 1 second
o Continuous GREEN led blink until paired or timed out
Pairing
LED Feedback
Pairing
Key Press
Features:
o RED if not BLE bonded
o GREEN if BLE bonded
Factory Reset
Unbind BLE
o 4 RED blinks before reboot
o 4 blinks if successful
o 2 blinks if unsuccessful
‐ UE878NMEH (512K Flash/64K RAM)
‐ BLE
‐ Voice with single digital MEMs microphone
‐ QS Cloud
o Same cloud Comcast accesses today, and implemented by Comcast
‐
Tri‐color (RGB) feedback LED for user feedback
o Same tri‐color LED used in XR15 and XR16 remotes
o Charge pump circuit to support blue color
‐ Option in battery compartment for 10 pin tag connection and 10 pin header
o Follow latest Sky EC302 design
SMT IR diode (Paralight L‐S15CAIR1C‐HD/ Bright LED Electronics Corp. BIR‐HMC33M‐2‐TRCA‐UEI)
PCB: Double Sided, CEM‐1, Carbon Thru Hole, Wet Film
‐ Buzzer/Piezo for Remote Finder feature (OWMB‐9045HS‐27‐16) – optional install
‐
‐
‐ Rubber keypad with carbon ink
‐ ABS plastic housing
‐
‐
PC IR lens
PMMA back printed crystal keys
o MIC
o HOME
‐ ABS key cap – OK key
‐ ABS key caps
‐ Metal domes – all 30 keys
‐
‐ Operating Temperature
o 0°C to +50°C
2 AAA batteries operation – designed for alkaline
Customer Marking Label
COMPLIANCE WITH FCC RULES AND REGULATIONS
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
•
• Connect the equipment into an outlet on a circuit different from that to which the receiver
Increase or decrease the separation between the equipment and receiver.
is connected.
Consult the dealer or an experienced remote control/ TV technician for help.
This equipment has been verified to comply with the limits for a Class B computing device,
pursuant to FCC Rules. The user is cautioned that changes and modifications made to the
equipment without the approval of manufacturer could void the user's authority to operate this
equipment.
FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2 This device must accept any interference received, including interference that may cause
undesired operation.
FCC ID: MG3‐R34010
Mexico
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operación no deseada.”
Canada:
This device complies with RSS‐210 of the Industry Canada Rules:
Operation is subject to the following two conditions:
(1) This deice may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est confrme aux CNR d’Industrie Canda applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’utilisateur de l’appareil doit accepter dout brouillage dadioélectrique subi, même si le
brouillage est susceptible d’en compromettre de fonctionnement.