FCC ID: B4Z-903-TCVR 319.5 MHz OEM Transceiver w/Crystal TX

600-1025 OEM Transceiver Module Installation Instructions 466-2226B May 2005 Description The OEM transceiver modules are compatible with GE Security wireless transmitters. The modules have an onboard receiver, microprocessor, and connection for a daughter board. The micro-

processor controls the receiver, providing antenna switching and AGC functions. It also analyzes the received data from the receiver, validates incoming packets, and returns packets to the receiver when polled. A daughter board, which communicates with the module via an 8-pin header, can be added to implement a variety of functions. Each module encapsulates the receiver functions and formats and presents a common interface to the daughter board. Therefore, even though protocols vary among the GE Security radio frequencies used around the world, the interface is the same to the daughter board. Installation guidelines Observe the following guidelines when installing the OEM trans-

ceiver module:

Allow at least 9 inches (22.9 cm) of clearance above the enclosure for the antennas. Avoid mounting locations that expose the module to mois-

ture. Avoid areas with excessive metal or electrical wiring including furnace and utility rooms. If unavoidable, mount on or near metal with the antenna extending above the metallic surfaces as shown in Figure 1. Figure 1. Mounting on or near metal Metal Metal Note:

For UL installations this module must be mounted in the 600-

1029 enclosure. Daughter boards have not been investigated for use by UL. Installation To mount the OEM transceiver module onto the back plate of the 600-1029 enclosure, do the following:

1. 2. Gently slide the top of the circuit board under the two top Insert the antennas into the antenna shrouds (Figure 2). latches. Figure 2. Installing the circuit board Antenna shrouds 600-1029 enclosure Top latches OEM transceiver 2 mm power jack Terminal block LEDs Bottom latch ON ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 4. Connect DC power to the OEM transceiver module using 2 mm power jacks (center positive) or connect flyleads to the terminal block as labeled on the board. Note:

For model 600-1025-02-43, the cable length must be less than 3 m (9.8 ft.) for CE compliance. LED operation Table 1 shows the LED indications for the OEM transceiver module. Table 1. OEM transceiver module LED indications Green LED On On One flash off Indication Powered up Communication with daughter baord Valid packet received Troubleshooting The following table gives troubleshooting suggestions for the OEM transceiver module. Table 2. Red LED Off Flashing Off or flashing OEM transceiver module troubleshooting CAUTION You must be free of static electricity before handling circuit boards. Wear a grounding strap or touch a bare metal surface to discharge static electricity. 3. Snap the circuit board in at the bottom latch to secure it in place as shown in Figure 2. Problem OEM transceiver modules green and red LEDs are off OEM receiver modules green LED is on and the red LED is off Action 1. Check that the transformer is plugged in. 2. Check the transformer to module wiring. Check the daughter board mounting. 2 600-1025 OEM Transceiver Module Installation Instructions 319.5 MHz 433.92 MHz 600-1025-02-95R and 600-1025-02-43 All 319.5 MHz sensors All 433 MHz sensors FCC compliance This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interfer-

ence that may cause undesired operation. Changes or modifications not expressly approved by GE Security can void the users authoriy to operate the equipment. Specifications Models Frequency 600-1025-02-95R 600-1025-02-43 Sensor compatability 600-1025-02-95R 600-1025-02-43 Power required (without daughter board) Typical Maximum Wireless range Listings 600-1025-02-95R 600-1025-02-43 Operating temperature Storage temperature Maximum relative humidity Dimensions Features UL (985 1023), FCC ID (B4Z-875-TCVR), DoC, IC: 867-875CVR CE 32 to 140F (0 to 60C)

-30 to 140F (-34 to 60C) 90% noncondensing 3.2 x 4.6 x 0.6 inches (8.1 x 11.7 x 1.5 cm) Antenna tamper, jam detect, wall tamper, cover tamper 600-1029 59-873 600-1031 40-262 Enclosure USB adaptor Repeater adaptor Stand-off 45mA 100mA 1,000 feet (305 m) CE declaration of conformity Manufacturers name:

GE Security Manufacturers address:

EU representative:

Product indentification:

R&TTE directive:

EMC:

Safety:

Radio:

Equipment class identifier:

(RF products falling under the scope of R&TTE) 1275 Red Fox Road Arden Hills, MN 55112 USA GE Security B.V. Kelvinstraat 7 6003 DH Weert The Netherlands Product: 433 MHz OEM Transceiver Model number: 600-1025-02-43 Brand: GE Security TUV 0123 / GE Security Test report reference: CEQP-600-1025-02-43 Applied standards: EN50130-4 (1995) +A1

(1998) GE Security Test report reference: CEQP-600-1025-02-43 Applied standards: EN60950-1:2001 TUV 0123 Test report reference: CEQP 600-1025-02-43 Applied standards: EN300220-3 v1.1.1 (09-

2000) None (class 1 product) Means of conformity We declare under our sole responsibility that this product is in conformity with Directive 93/68/EEC (Marking) and/or complies to the essential requirements and all other relevant provisions of the 1999/5/EC (R&TTE) based on test results using

(non) harmonized standards in accordance with the Directives mentioned. Toll-free: 888.437.3287 (US including Alaska and Hawaii; Puero Rico; Canada) Outside the toll-free area: Contact your local dealer. Technical support www.gesecurity.com