FCC ID: B4Z-786A-DTIM Telephone Interface Module

*(,QWHUORJL[

ZZZ*(,QWHUORJL[6HFXULW\FRP

'LDORJ7HOHSKRQH,QWHUIDFH 0RGXOH

,QVWDOODWLRQ,QVWUXFWLRQV

'RFXPHQW1XPEHU5HY%

2FWREHU

35(/,0,1$5<

Preliminary 10/4/02 Product Summary Installation The Dialog Telephone Interface Module (DTIM) is a battery operated communication link between the security system control panel and the central monitoring station. The DTIM receives radio signals from the panel, then uses the phone line to report security system events to the central monitoring station. The DTIM provides added security by separating the telephone interface from the panel. If the panel is damaged during a break-in or fire, the DTIM can still report to the central monitoring station. The DTIM is a supervised device that transmits supervisory signals every hour for the panel to receive. When the battery is low, the module transmits a low battery signal. Note The DTIM does not have a backup power supply. Therefore, the battery must be replaced within 7 days when a low battery condition occurs to ensure that system events can be reported. If the battery is allowed to completely drain, the panel identifies the DTIM as being in a supervisory (non-working) state, which prevents system events from being reported. Tools and Supplies Needed Phillips screwdriver

Mounting Hardware (included)

Ty-wrap and Cover Screw for UL Listed installations (included) This section describes guidelines for installing the DTIM, programming, testing, mounting, and phone line connections. Installation Guidelines

Before permanently mounting to a wall, test the DTIM from the desired location to ensure communication with the panel. This means you must first add (learn) the DTIM into panel memory, then perform a sensor test.

Mount the module within 100 feet of the panel, but not closer than 10 feet to another DTIM or the panel.

Always mount the DTIM in the upright vertical position.

The DTIM can be connected to a standard analog (loop-start) phone line, with or without digital subscriber line (DSL) service. Note The DTIM cannot be used on digital or PBX phone lines, which are designed only for digital type devices that operate anywhere from 5 volts DC and up. The DTIM uses an analog modem and does not have a digital converter, adapter, or interface to operate with such systems.

When connecting the DTIM to a standard analog phone line, it is recommended that you install an RJ-31X jack (CA-38A in Canada) ahead of all phones and other devices on the line for full line seizure. This allows the DTIM to take control of the phone line when an alarm occurs, even if the phone is in use or off-hook. It also provides customers with a quick dis-

connect in case the DTIM malfunctions, allowing them to use their phone.

For UL Listed installations, mount the RJ-31X jack within 5 feet of the DTIM. 1 Preliminary 10/4/02 ProgrammingAdding the DTIM to Panel Memory Note We recommend learning the DTIM into Allegro panels as zone 1, since zone 1 is set up to learn into Group 36 automatically and has pre-programmed sensor text for the DTIM (PHONE MOD-

ULE). The DTIM uses a 3-2-1 tamper switch activation sequence for learning, which causes the LED to blink in a corresponding 3-2-1 sequence. You must wait for the LED to turn off after each flash sequence before releasing the tamper switch (see Figure 2). To learn the DTIM into the panel:

1. Remove the DTIM cover and install the antennas (see Figure 1). Align antenna.. ..push down until bare metal is not visible. Repeat for other antenna. Figure 1. Antenna Installation Note Antennas must be installed for learning. 2. With the system disarmed, enter program mode at the Allegro panel by pressing 8 + CODE. twice and twice. The Allegro display shows ZONE 01 - TRIP. 3. Press 4. Locate the DTIM tamper switch and LED (see Figure 2 at left). Important !

Timing is the key to success with step 5. Read the complete step before you begin to help ensure successful programming. Do not wait more than 1 second between tamper switch activa-

tions in step 5. If you wait too long, the LED will not flash and you must start over. Also, do not release the tamper switch before the LED is done flashing or you must start over. 5. Press and release the DTIM tamper switch as follows:

Press 3 times, holding the tamper switch down on the third press until the LED flashes 3 times, then release after the third flash. LED Tamper Switch Figure 2. Tamper Switch and LED Locations Immediately press 2 times, holding the tamper switch down on the second press until the LED flashes 2 times, then release after the second flash. Immediately press and hold until the LED flashes 1 time, then release the tamper switch. 6. Exit from program mode. Testing DTIM Transmitting Range The following describes the basic steps for testing transmitting range from the DTIM to the panel. For complete testing instructions, see the panel installation instructions. Note Be sure to attach the cover onto the DTIM before testing wireless communications. 1. Place the DTIM in the desired location. 2. Put the Allegro panel into sensor test mode. The panel piezo should sound 7 - 8 beeps. This indicates good reception from the DTIM to the panel. If you hear fewer than 7 beeps, test the DTIM in different locations. Mounting locations should be limited to areas where the panel responds with 7 - 8 beeps. 3. 4. To retest transmitting range after relocating the DTIM, press then at the Allegro panel and listen for 7 - 8 beeps. 5. Exit from test mode after determining acceptable locations. 2 Dialog Telephone Interface Module Installation Instructions Preliminary 10/4/02 Mounting After finding an acceptable mounting location (based on testing), mount the DTIM as described. You must be free of static electricity before handling circuit boards. Touch a bare metal surface or wear a grounding strap to discharge yourself. 1. With the cover off, place the DTIM at the desired location and mark the mounting holes (see Figure 3 at left). 2. Make holes in the wall for anchors at the marked locations. 3. Insert wall anchors where necessary, then use two #6 screws to secure the DTIM to the wall. Wiring a Phone Line to the Module Connect the DTIM ahead (or in front) of all other phones, answering machines, computers, or any other devices on the phone line. This allows the DTIM to take over (seize) the phone line, even if another device on the line is in use. An RJ-31X (CA-38A) jack should be installed when wiring for full line seizure. This lets the user quickly and easily disconnect the DTIM from the phone line in case the DTIM disables the phone line due to a malfunction. Note For UL Listed systems, the RJ-31X jack must be mounted within 5 feet of the DTIM. 1. Run a 4-conductor cable from the TELCO block to the RJ-31X (A in Figure 4). 2. Connect the 4-conductor cable wires to the RJ-31X (B in Figure 4). 3. Disconnect the Green and Red premises phone jack wires from the TELCO block and splice them to the 4-conductor cable Black and White (or Yellow) wires (C in Figure 4). Use weath-

erproof wire connectors for these splices. 4. Connect the 4-conductor cable Green and Red wires to the TELCO block TIP (+) and Red to RING (-) posts (D in Figure 4). Insert the 8-conductor phone cord plug into the RJ-31X jack (E in Figure 4). 5. 6. Remove the right knockout on the DTIM plastic, feed the 4-conductor phone cord plug through it and connect the plug into the DTIM phone jack

(Figure 5 at right). Phone Jack Phone Test After connecting the phone line to the DTIM, conduct a phone test to verify reports are made to the central monitoring station. The following steps describe the basic steps for conducting a phone test. Refer to the specific panel installation instructions for complete details. Note You must conduct a phone test whenever the DTIM battery is replaced. 1. Call the central monitoring station to inform them you are testing the system. 2. Make sure the panel has the correct account number and central station receiver phone num-

Knockout Removed Figure 5. Knockout and Phone Jack Locations ber programmed. 3. Enter the appropriate phone test command for the panel used in the system. 4. Contact the central monitoring station when you are finished testing. Installing the Battery Ty-wrap and Cover Screw (UL Listed Installations Only) After installation, programming, and testing are completed install the Ty-wrap around the battery and battery holder. Cut off any access. Secure the cover with the cover screw by installing it through the cover push tab. Figure 3. Mounting Hole Locations E BRN GRY B GRN n e e r G k c a l B d e R RED

) w o l l e Y r o

e t i h W TIP

(+) RING

(-) D A Black Green C White (or Yellow) Red Figure 4. RJ31X Phone Wiring Dialog Telephone Interface Module Installation Instructions 3 Preliminary 10/4/02 Trouble-

shooting Note Disconnect the phone line from the DTIM before servicing. No Dial Tone If there is no dial tone at on-site phones after wiring the RJ-31X jack, use the following to find the cause.

Wait 2 minutes and try again. The DTIM may be busy trying to report to the central station.

Check the DB-8 cord connections at the modul e and RJ-31X jack. Replace the cord if neces-

sary.

Disconnect the DB-8 cord from the RJ-31X jack. If the phone still doesnt work, the problem is in the RJ-31X jack wiring. Check the RJ-31X jack wiring and TELCO block wiring. Replace the RJ-31X jack if necessary. Perform a phone test after troubleshooting the phone line (see your panel installation instructions for phone test procedures). Constant Dial Tone If a constant dial tone prevents you from using the phone, there may be one or more polarity-

sensitive phones on the premises. Reverse the phone wires connected to the brown and gray wire terminals on the RJ-31X jack. No System Response If the system does not respond in sensor test (as described in the panel installation instructions), try the following:

Change the antenna position. Best range is achieved by inserting the antenna into the wall.

Check that the DTIM battery is installed.

Check the DTIM for a dead battery. Replace the battery if necessary.

Use an RF Sniffer (60-401) to verify that the DTIM is transmitting.

Verify that the DTIM was added (lear ned) into panel memory correctly. Trouble Condition

The tamper switch may have been tripped. Check that the cover is securely in place.

The DTIM battery may be low. Check the battery, replace if necessary and conduct a phone test. Module Supervisory If the panel indicates a DTIM supervisory condition, use an RF Sniffer (60-401) to verify that the DTIM transmits when the tamper switch is pressed. If it does not transmit, check the bat-

tery and replace it if necessary. If the sniffer indicates that the DTIM is transmitting, it may be out of panel receiving range. Use the sensor test to verify that the DTIM is within panel range. If necessary, test the DTIM from other locations until an acceptable location is found. Specifications Compatibility: .............. Allegro Wireless Range ............. 500 feet open-air (nominal) Power Source: .............. 3.6 V AA Lithium Battery Storage Temperature: .... -30 F to 140 F (-34 C to 60 C) Operating Temperature: 32 F to 120 F(0 C to 49 C) Maximum Humidity: ... 90% relative humidity, noncondensing Dimensions: 4.6 (12 cm) W, 6.6 (3 cm) H, 1.20 (17 cm) D US Patents 4,855,713 and 4,864,636 4 Dialog Telephone Interface Module Installation Instructions

Preliminary 10/4/02 Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by Interlogix, Inc. can void the users authority to operate the equip-

ment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. FCC Part 15 ID No. B4Z-786A-DTIM ACTA Part 68 This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. FCC Part 68 Registration No. B4ZAL01B46059 The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result in devices not ringing in response to an incoming call. In most areas, the sum of all device RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as deter-

mined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the appli-

cable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular jack that is also compliant. See the Installation Instructions for details. Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ31X jack that is electrically in series and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an RJ31X jack and alarm dialing equipment for you. If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be given advance notice in order to maintain uninterrupted service. Dialog Telephone Interface Module Installation Instructions 5

A J M

H

5 A H L E

A 2 H

L E

A H

I

E

E J E A I 6 A

A F D

A

E

A

A J M

H

, A

H

J E

2

E

J 6 A

A F D

A

I M A H E

C 5 O I J A

N

D E

A

F K J A H 6 A

A F D

A 6 A

A F D

A

H

, E

E

C

G K E F

A

J 4

7

K I A

4

7

K I A

4

K I J

A H

2 H A

E I A I

G K E F

A

J

9 E H E

C Preliminary 10/4/02 If you experience trouble with this equipment, please contact the company that installed the equipment for service and/or repair information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Declaration of Conformity (DoC) GE Interlogix, Inc. declares that the model no. 60-879-95R is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada Notice The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the users satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local tele-

communications company. The equipment must also be installed using an acceptable method of connection. In some cases, the companys inside wiring associated with a single-line individual service may be extended by means of a certi-

fied connector assembly (telephone extension cord). The customer should be aware that compliance with the above condi-

tions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunica-

tions company cause to request the user to disconnect the equipment. For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a tele-

phone loop that is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number:

0.2B AC The term IC: before the certification/registration number only signifies that the Industry Canada technical specifica-

tions were met. IC: 867A 786DTIM AVIS: - L tiquette du ministre des Communications du Canada identifie le matriel homologu. Cette tiquette certifie que le matriel est conforme a certaines normes de protection, d exploitation et de scurit des rseaux de tlcommuni-

cations. Le ministre n assure toutefois pas que le matriel fonctionnera a la satisfaction de l utilisateur. Avant d installer ce matriel, l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l enter-

prise locale de tlcommunication. Le matriel doit galement etre install en suivant une mthod accepte de raccorde-

ment. Dans certains cas, les fils intrieurs de l enterprise utiliss pour un service individuel a ligne unique peuvent etre prolongs au moyen d un dispositif homologu de raccordement (cordon prolongateur tlphonique interne). L abonn ne doit pas oublier qu il est possible que la conformit aux conditions nonces ci-dessus n empechent pas le dgrada-

tion du service dans certaines situations. Actuellement, les enterprises de tlcommunication ne permettent pas que l on raccorde leur matriel a des jacks d abonn, sauf dans les cas prcis prvus pas les tarrifs particuliers de ces enterprises. Les rparations de matriel homologu doivent etre effectues pas un centre d entretien canadien autoris dsign par le fournisseur. La compagne de tlcommunications peut demander a l utilisateur de dbrancher un appareil a la suite de rparations ou de modifications effectues par l utilisateur ou a cause de mauvais fonctionnement. Pour sa propre protection, l utilisateur doit s assurer que tous les fils de mise a la terre de la source d nergie lec-

trique, des lignes tlphoniques et des canalisations d eau mtalliques, s il y en a, sont raccords ensemble. Cette pr-

caution est particulirement importante dans les rgions rurales. Avertissment. - L utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d inspection des installations lectriques, ou a electricien, selon le cas. Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l intention des utilisateurs du matriel terminal, doit etre incluse dans l information qui accompagne le materiel homologu. La note pourrait etre rdige selon le modle suivant:

L indice de charge (IC) assign a chaque dispositif terminal indique, pour viter toute surcharge, le pourcentage de la charge totale qui peut etre raccorde a un circuit tlphonique boucl utilis par ce dispositif. La terminaison du circuit boucl peut etre constitue de n import somme des indices de charge de l ensemble des dispositifs ne dpasse pas 100. L Indice de charge de cet produit est ____________. 6 Dialog Telephone Interface Module Installation Instructions Preliminary 10/4/02 Dialog Telephone Interface Module Installation Instructions 7 Preliminary 10/4/02

*(,QWHUORJL[$OOHJURLVDWUDGHPDUNRI*(,QWHUORJL[

$OOULJKWVUHVHUYHG

*(,QWHUORJL[

6HFRQG6WUHHW1RUWK

1RUWK6DLQW3DXO01

3KRQH

86$ &DQDGD

7HFKQLFDO6XSSRUW

8 Dialog Telephone Interface Module Installation Instructions

Preliminary 2/11/02

'LDORJ7HOHSKRQH

,QWHUIDFH0RGXOH ITI Part No. 60-879-95R Document Number: 466-1849 Rev. A February 2002 Product Summary The Dialog Telephone Interface Module (DTIM) is a bat-

tery operated communication link between the security sys-

tem control panel and the central monitoring station. The DTIM provides added security by separating the telephone interface from the panel. If the panel is damaged during a break-in or fire, the DTIM can still report to the central monitoring station. The DTIM receives radio signals from the panel, then uses the phone line to report security system events to the central monitoring station. The DTIM is a supervised device that transmits supervisory signals every hour for the panel to receive. When the battery is low, the module transmits a low battery signal. Note The DTIM does not have a backup power supply. There-

fore, the battery must be replaced immediately when a low battery condition occurs to ensure that system events can be reported. If the battery is allowed to completely drain, the panel identifies the DTIM as being in a supervi-

sory (non-working) state, which prevents system events from being reported. Installation Guidelines Use the following guidelines when installing the DTIM. Before permanently mounting to a wall, test the DTIM from the desired location to ensure communication with the panel. This means you must first add (learn) the DTIM into panel memory, then perform a sensor test. Mount the module within 100 feet of the panel, but not closer than 10 feet to another DTIM or the panel. Always mount the DTIM in the upright vertical posi-

tion. The DTIM can be connected to a standard analog

(loop-start) phone line, with or without digital sub-

scriber line (DSL) service. Note The DTIM cannot be used on digital or PBX phone lines, which are designed only for digital type devices that oper-

ate anywhere from 5 volts DC and up. The DTIM uses an analog modem and does not have a digital converter, adapter, or interface to operate with such systems. When connecting the DTIM to a standard analog phone line, it is recommended that you install an RJ-31X jack

(CA-38A in Canada) ahead of all phones and other devices on the line for full line seizure. This allows the DTIM to take control of the phone line when an alarm occurs, even if the phone is in use or off-hook. It also Installation Instructions provides customers with a quick disconnect in case the DTIM malfunctions, allowing them to use their phone. For UL Listed installations, mount the RJ-31X jack within 5 feet of the DTIM. Tools Needed Phillips screwdriver Two #6 phillips-head screws (included) Two wall anchors (included) Pencil Installation This section describes programming, testing, mounting, and phone line connections. ProgrammingAdding the DTIM to Panel Memory This section describes the steps for adding (learning) the DTIM into panel memory, which requires a series of mod-

ule tamper switch activations and module LED responses

(see Figure 1). Tamper Switch LED Figure 1. Tamper Switch and LED Locations The DTIM uses a 3-2-1 tamper switch activation sequence for learning, which causes the LED to blink in a corre-

sponding 3-2-1 sequence. You must wait for the LED to turn off after each flash sequence before releasing the tamper switch. Note The DTIM should be learned into panel memory as zone 1. 1

4 1

4 1

6 1 2

6 1 2

Preliminary 2/11/02 To learn the DTIM into the panel:

Important !

Timing is the key to success with this procedure. Do not wait more than 1-2 seconds between steps 4 and 5 or steps 5 and 6 after releasing the tamper switch. If you wait too long between these steps, the LED will not flash and you will have to start over. Also, do not release the tamper switch before the LED is done flashing or you will have to start over. 1. Remove the DTIM cover and set it aside (see Figure 2). Push Tab Up Figure 2. Removing the Cover Lift Cover Up 2. With the system disarmed, enter program mode by pressing 8 + CODE. 3. Press twice and twice. The display shows ZONE 01 - TRIP. 4. Press the DTIM tamper switch three times, holding the tamper switch down on the third press and wait for the the LED to flash 3 times, then release the tamper switch after the third flash. 5. Press the DTIM tamper switch twice, holding the tamper switch down on the second press and wait for the LED to flash two times, then release the tamper switch after the second flash. 6. Press and hold the tamper switch down until the LED flashes once, then release the tamper switch after the flash. The panel beeps twice and the display shows the next available sensor number. 7. Exit from program mode. Testing This section describes the basic steps for testing transmit-

ting range from the DTIM to the panel. For complete testing instructions, see the panel installation instructions. Note Be sure to attach the cover onto the DTIM before testing wireless communications. 1. Straighten the antenna to a vertical position. 2. Place the DTIM in the desired location. 3. Put the panel into sensor test mode. 4. Listen for the panel piezo to sound 7 - 8 beeps. This indicates good reception from the DTIM to the panel. 2 5. If you hear fewer than 7 beeps, test the DTIM in differ-

ent locations. Mounting locations should be limited to areas where the panel responds with 7 - 8 beeps. 6. To retest transmitting range after relocating the DTIM, press then and listen for 7 - 8 beeps. 7. Exit from test mode after determining acceptable loca-

tions. Mounting/Receiving Antenna Positioning After finding an acceptable mounting location (based on testing), mount the DTIM and position the antenna as described. The antenna can be inserted into a wall or posi-

tioned upright inside the antenna housing. Note For best range, it is recommended to insert the antenna into the wall. Mounting with Receiving Antenna in Wall

&$87,21 You must be free of static electricity before handling circuit boards. Touch a bare metal surface or wear a grounding strap to discharge yourself. 1. Remove the circuit board from the plastic housing by pushing up on the tab and pulling the board outward

(see A in Figure 3). Place the board in the cover. A Receiving Antenna Tab B Mounting Hole Antenna Insertion Hole Mounting Hole Figure 3. Removing the Circuit Board to Mark Mount-

ing and Antenna Holes 2. Mark the mounting holes and the antenna insertion hole

(see B in Figure 3). 3. Make holes in the wall for anchors at the marked loca-

4. 5. 6. tions. Insert wall anchors where necessary, then use two #6 screws to secure the plastic housing to the wall. Insert the antenna into the antenna insertion hole and re-install the board onto the plastic base, bottom first then push in at the top until it snaps in under the tab. Install the protective dust cap (included in accessory packet) in the hole located on the top-right of the DTIM plastic housing.

4 1

4 1

6 1 2

6 1 2

Preliminary 2/11/02 Mounting with Antenna Housing 1. Hold the DTIM against the wall and mark the mounting holes (see A in Figure 4). Be sure to leave at least 4 inches above the DTIM for the antenna housing. Antenna Housing Receiving Antenna A B Mounting Hole Mounting Hole Figure 4. Mounting Hole Locations and Antenna Hous-

ing Installation 2. Slide the antenna housing over the antenna and snap the housing into the upper-right hole (see B in Figure 4). 3. Make holes in the wall for anchors at the marked loca-

tions, then insert wall anchors where necessary and secure the module to the wall using two #6 screws. Wiring a Phone Line to the Module Basically, there are two methods for connecting the DTIM to a phone line; full line seizure and no line seizure. Full Line Seizure This method requires that the DTIM be wired ahead (or in front) of all other phones, answering machines, computers, or any other devices on the phone line. This allows the DTIM to take over (seize) the phone line, even if another device on the line is in use. An RJ-31X (CA-38A) jack should be installed when wiring for full line seizure. This lets the user quickly and easily dis-

connect the DTIM from the phone line in case the DTIM disables the phone line due to a malfunction. Full Line Seizure Wiring with an RJ-31X Note For UL Listed systems, the RJ-31X jack must be mounted within 5 feet of the DTIM. 1. Run a 4-conductor cable from the TELCO block to the RJ-31X (A in Figure 5). 2. Connect the 4-conductor cable wires to the RJ-31X (B in Figure 5). 3. Disconnect the Green and Red premises phone jack wires from the TELCO block and splice them to the 4-

conductor cable Black and White (or Yellow) wires (C in Figure 5). Use weatherproof wire connectors for these splices. 4. Connect the 4-conductor cable Green and Red wires to the TELCO block TIP (+) and Red to RING (-) posts

(D in Figure 5). 5. Connect the DB-8 cord (not included) to the RJ-31X and the DTIM terminals (E in Figure 5). n e e r G n w o r B y a r G d e R E BRN GRY B GRN RED k c a l B n e e r G d e R e t i h W

) w o l l e Y r o

TIP RING

(-) A D Green Black C Green Red White (or Yellow) Red Premises Phone Jack Wires Figure 5. Full Line Seizure Wiring with an RJ-31X 3

4 1

4 1

6 1 2

6 1 2

4 1

4 1

6 1 2

6 1 2

4 1

4 1

6 1 2

6 1 2

Preliminary 2/11/02 No Line Seizure This method is typically used where DSL (digital subscriber line) service exists. DSL allows multiple devices on a single phone line to be used simultaneously. Simply connecting a standard phone cord to an available phone jack on the pre-

mises is all that is required. An in-line filter may be required to ensure panel reporting is successful (see Figure 6). Note Connecting the DTIM to a standard phone (voice) line without DSL service in this manner should be avoided. Other devices in use at the same time the DTIM is using the line can prevent reports from going through. n e e r G d e R DSL In-Line Filter Premises Phone Jack Constant Dial Tone If a constant dial tone prevents you from using the phone, there may be one or more polarity-sensitive phones on the premises. Reverse the phone wires con-

nected to the brown and gray wire terminals on the RJ-

31X jack. No System Response If the system does not respond in sensor test (as described in the panel installation instructions), try the following:

Change the antenna position. Best range is achieved by inserting the antenna into the wall. Check that the DTIM battery is installed. Check the DTIM battery for low voltage. Replace the battery if necessary. Use an RF Sniffer (60-401) to verify that the DTIM is transmitting. Verify that the DTIM was added (learned) into panel memory correctly. Trouble Condition The tamper switch may have been tripped. Check that the cover is securely in place. The DTIM battery may be low. Check the battery and replace if necessary. Module Supervisory If the panel indicates a DTIM supervisory condition, use an RF Sniffer (60-401) to verify that the DTIM transmits when the tamper switch is pressed. If it does not transmit, check the battery and replace it if neces-

sary. If the sniffer indicates that the DTIM is transmitting, it may be out of panel receiving range. Use the sensor test to verify that the DTIM is within panel range. If neces-

sary, test the DTIM from other locations until an acceptable location is found. Figure 6. No Line Seizure with DSL Service Troubleshooting Specifications Compatibility: .............. Allegro No Dial Tone If there is no dial tone at on-site phones after wiring the RJ-

31X jack, use the following to find the cause. Wait 2 minutes and try again. The DTIM may be busy trying to report to the central station. Check the DB-8 cord connections at the module and RJ-31X jack. Replace the cord if necessary. Disconnect the DB-8 cord from the RJ-31X jack. If the phone still doesnt work, the problem is in the RJ-31X jack wiring. Check the RJ-31X jack wiring and TELCO block wiring. Replace the RJ-31X jack if nec-

essary. Perform a phone test after troubleshooting the phone line

(see your panel installation instructions for phone test procedures). 4 Wireless Range ............. 500 feet open-air (nominal) Power Source: .............. 3.6 V AA Lithium Battery Storage Temperature:.... -30 F to 140 F (-34 C to 60 C) Operating Temperature: 32 F to 120 F(0 C to 49 C) Maximum Humidity: ... 90% relative humidity, noncon-

densing Dimensions: ................. W = 4.6 inches (11.7 cm) x D = 1.2 inches (3.0 cm) x H = 6.6 inches

(16.8 cm) plus 3.5 inches (8.9 cm) for antenna housing

4 1

4 1

6 1 2

6 1 2

Preliminary 2/11/02 Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by Interlogix, Inc. can void the users authority to operate the equipment. FCC Part 15 Class B Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of con-

nection. In some cases, the companys inside wiring associated with a sin-

gle-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degrada-

tion of service in some situations. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a resi-

dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. FCC ID No. B4Z-786A-DTIM FCC Part 68 This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the FCC reg-

istration number and the ringer equivalence number (REN) for this equip-

ment. If requested, this information must be provided to the telephone company. The REN is used to determine the maximum number of devices that may be connected to your telephone line. In most areas, the sum of all device RENs should not exceed five (5.0). If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be noti-

fied as soon as possible. You will also be advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. You will be given advanced notice in order to maintain uninter-

rupted service. If you experience trouble with this equipment, please contact:

ITI 2266 Second Street North North Saint Paul, MN 55109 1-800-777-2624 This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Declaration of Conformity (DoC) Interactive Technologies, Inc. declares that the ITI model no. 60-879-95R is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada Notice The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain tele-

communications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the users satisfaction.

&$87,21 Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority. The Load Number (LN) assigned to each terminal device denotes the per-

centage of the total load to be connected to a telephone loop that is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number: 0.2B AC AVIS: - L tiquette du ministre des Communications du Canada identi-

fie le matriel homologu. Cette tiquette certifie que le matriel est con-

forme a certaines normes de protection, d exploitation et de scurit des rseaux de tlcommunications. Le ministre n assure toutefois pas que le matriel fonctionnera a la satisfaction de l utilisateur. Avant d installer ce matriel, l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l enterprise locale de tlcommunica-

tion. Le matriel doit galement etre install en suivant une mthod accepte de raccordement. Dans certains cas, les fils intrieurs de l enter-

prise utiliss pour un service individuel a ligne unique peuvent etre pro-

longs au moyen d un dispositif homologu de raccordement (cordon prolongateur tlphonique interne). L abonn ne doit pas oublier qu il est possible que la conformit aux conditions nonces ci-dessus n empechent pas le dgradation du service dans certaines situations. Actu-

ellement, les enterprises de tlcommunication ne permettent pas que l on raccorde leur matriel a des jacks d abonn, sauf dans les cas prcis pr-

vus pas les tarrifs particuliers de ces enterprises. Les rparations de matriel homologu doivent etre effectues pas un cen-

tre d entretien canadien autoris dsign par le fournisseur. La compagne de tlcommunications peut demander a l utilisateur de dbrancher un appareil a la suite de rparations ou de modifications effectues par l util-

isateur ou a cause de mauvais fonctionnement. Pour sa propre protection, l utilisateur doit s assurer que tous les fils de mise a la terre de la source d nergie lectrique, des lignes tlphoniques et des canalisations d eau mtalliques, s il y en a, sont raccords ensem-

ble. Cette prcaution est particulirement importante dans les rgions rurales. Avertissment. - L utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d inspection des installations lectriques, ou a electricien, selon le cas. Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l intention des utilisateurs du matriel terminal, doit etre incluse dans l information qui accompagne le materiel homologu. La note pourrait etre rdige selon le modle suivant:

L indice de charge (IC) assign a chaque dispositif terminal indique, pour viter toute surcharge, le pourcentage de la charge totale qui peut etre raccorde a un circuit tlphonique boucl utilis par ce dispositif. La ter-

minaison du circuit boucl peut etre constitue de n import somme des indices de charge de l ensemble des dispositifs ne dpasse pas 100. L Indice de charge de cet produit est ____________. 5 Preliminary 2/11/02 2266 Second Street North | North Saint Paul Mn | 55109 | 800-777-2624 | www.itii.com | www.interlogixsecurity.com 2002 Interlogi x, I nc. Interlo gix and Allegro are trademarks of Interlogi x, Inc. ITI is a regi stered tra dema rks of In terl ogix, In c. 6