FCC ID: ORP-IBT-07 BLUETOOTH MODULE FOR AUDIO APPLICATION

iBT-07 Bluetooth Module for Audio Application iBT-07 This module is limited to OEM installation ONLY Bluetooth Module for Audio Application

( Qualified QDID : B020169 ) Doc. Name Date Revision

iBT-07-Rev0.6.01 2012-11-29 0.6.01 Copyright , 2012 by Engineering Department, Valence Semiconductor Design Limited. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means without the prior written permission of Valence Semiconductor Design Limited. 0.6.01 1 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application 1. Overview iBT-07 is a Class 2 Bluetooth module supporting Bluetooth v3.0 specification. It is implemented by using the CSR8610 ROM chip. iBT-07 is designed for receiving audio data transmitting from a mobile device. It can also be used to control the audio playing function of the remote device. 2. Features

A single chip radio and baseband IC for Bluetooth applications Fully Qualified Bluetooth v3.0 Class 2 power output (10Meter minimum) Support for 802.11 co-existence

High quality 95dB SNR DAC playback

Support for noise and echo cancellation 3. Applications

Wireless speakers

Hands-free car kit Stereo headset 4. Pin Drawing

Configurable 5-band EQ Supporting profiles : A2DP1.2, AVRCP1.0, HSP1.2 and HFP1.6 Build-in PCB antenna Supply voltage : 3.0V to 3.6V RoHS compliant

Dimension: 29.7mm (L) x 11.9mm (W) x 2.2mm (H)

VoIP handsets

Docking Stations E S N E S _ T A B V 3 3 T X E _ G H C 2 3 D N G A 6 3 G H C V 5 3 T A B V 4 3 P D 1 3 M D 0 3 1 2 O I P 9 2 0 2 O I P 8 2 B S C _ I P S

4 O I P 7 2 I S O M _ I P S

2 O I P 6 2 O S I M _ I P S

3 O I P 5 2 K L C _ I P S

5 O I P 4 2 B T E S E R 3 2 D N G 2 2 1 D N G 0.6.01 2 P A _ C M I 3 N A _ C M I 4 N L _ K P S 5 P L _ K P S 6 C N 7 C N 8 3 1 O I P 9 D D V 0 1 C N 1 1 C N 2 1 D N G 3 1 7 1 O I P 4 1 8 1 O I P 5 1 9 1 O I P Figure 1 iBT-07 Pin Diagram 2 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application 5. Pin Description Pin Name GND MIC_AP MIC_AN SPK_LN SPK_LP NC NC PIO13 VDD NC NC GND PIO17 PIO18 PIO19 GND BT_TX BT_RX Application Usage GND AMP_SDB VDD GND CONNECT PAIR VOL_UP GND Pin Type AI AI AO AO B B B B Pin Descriptions Ground Microphone A Positive Input Microphone A Negative Input Negative Output of Left Speaker Positive Output of Left Speaker No Connect No Connect Programmable I/O pin 3.3V Supply Voltage for I/O Pads No Connect No Connect Ground Programmable I/O pin Programmable I/O pin Programmable I/O pin Ground O4, PU Bluetooth UART Data Output IS, PD Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 SPI_PCMB SPI_PCMB LED0 LED1 GND LED0 LED1 GND B OD4 OD4 RESETB RESETB IS, PU 24 PIO5/SPI_CLK VOL_DN IS, PD 25 PIO3/SPI_MISO PLAY / PAUSE B, PD 26 PIO2/SPI_MOSI FWD IS, PD 27 PIO4/SPI_SYNC REV O4, PD 28 29 30 31 32 PIO20 PIO21 DM DP CHG_EXT B B B B A Bluetooth UART Data Input Selection for SPI or PCM Open Drain LED Driver Output Open Drain LED Driver Output Ground Active Low Module Reset. Must be low for > 5mS This pin has multiple functions SPI_PCMB = 0, this pin will be either a programmable I/O pin or be set as the digital audio data output clock SPI_PCMB = 1, this pin will function as the SPI clock This pin has multiple functions SPI_PCMB = 0, this pin will be either a programmable I/O pin or be set as the digital audio data output SPI_PCMB = 1, this pin will function as the SPI data output This pin has multiple functions SPI_PCMB = 0, this pin will be either a programmable I/O pin or be set as the digital audio data input SPI_PCMB = 1, this pin will function as the SPI data input This pin has multiple functions SPI_PCMB = 0, this pin will be either a programmable I/O pin or be set as the digital audio data synchronization output SPI_PCMB = 1, this pin will function as the SPI chip select Programmable I/O pin Programmable I/O pin USB DM Signal USB DP Signal External Battery Charger control. Connect to the base of an external battery charger transistor when using external charger booster. Otherwise leave unconnected. 0.6.01 3 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application Pin No. Pin Name Application Usage Pin Type Pin Descriptions 33 VBAT_SENSE VBAT VCHG AGND MIC_BIAS AIO0 VREG_EN 34 35 36 37 38 39 O4 4mA output pad OD Open drain output pad I IS Schmidt Trigger Input B Bidirectional Input GND A A A A A, B ON / STBY I, WPD Battery Charger Sense input Connect directly to the battery positive pin. Otherwise connect to 3V3 if battery charger is not used. Battery Positive Terminal Connect directly to the battery positive pin. Otherwise connect to 3V3 if battery charger is not used. Battery Charge input terminal Leave this pin unconnected if battery charger is not required. Ground Microphone Bias Analog Input / Programmable I/O Active High to enable the internal 1.8V regulator which will then wake up the iBT-07 module Strong Pull-up Strong Pull-down SPU SPD WPU Weak Pull-up WPD Weak Pull-down A Analog Table 1 iBT-07 Pin Description Table 0.6.01 4 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application 6. Electrical Specification 6.1. Absolute Maximum Rating Item Power Supply Voltage Peak Current Storage Temperature Symbol VDD Ipk TSTG Rating

-0.4 to 3.7 0 - 70

-20 to 85 Unit V mA

C 6.2. Recommended Operating Condition Item Power Supply Voltage RF Operating Temperature Operating Temperature Symbol VDD Miin 3.0 0 0 6.3. Digital Input / Output Port Characteristics Typ 3.3 25 25 Max 3.6 80 55 Unit V

C

C VDD=3.3V, operating temperature = 25 C unless specified otherwise Symbol Min. Parameter Condition Input Voltage Levels VIL VIH Vsch Input low voltage Input high voltage Schmitt voltage level Output Voltage Levels VOL VOH Output low voltage Output high voltage Input and Tri-state Current with Strong pull-up Strong pull-down Weak pull-up Weak pull-down I/O Pad leakage current Input Capacitance Current Consumption Operating Current Standby Current IOL = -4mA IOH = 4mA Depends on profiles

-0.3 0.625*VDD 0.25*VDD 0.75*VDD

-100 10

-5 0.2

-1 1 Typ. Max. Unit

-40 40

-1 1 0 35 0.25*VDD VDD+0.3 0.625*VDD 0.125 VDD

-10 100

-0.2 5 1 5 0.5 V V V V V uA uA uA uA uA pF mA mA 0.6.01 5 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application 6.4. RF Characteristics VDD=3.3V, operating temperature = 20 C unless specified otherwise Receiver Units Miin Typ Max Sensitivity at 0.1% BER Maximum Receiver Signal at 0.1% BER C/I Co-Channel Adjacent Channel Selectivity C/I +1MHz Adjacent Channel Selectivity C/I -1MHz 2nd Adjacent Channel Selectivity C/I +2Mhz 2nd Adjacent Channel Selectivity C/I -2Mhz 3rd Adjacent Channel Selectivity C/I +3Mhz 3rd Adjacent Channel Selectivity C/I -3Mhz dBm dBm dB dB dB dB dB dB dB

-83

-6 10

-4

-4

-35

-21

-45

-45

-82 0 11 0 0

-30

-20 Bluetooth Spec

-70

-20 11 0 0

-30

-20

-40

-40 VDD=3.3V, operating temperature = 20 C unless specified otherwise Transmitter Units Miin RF Output Power RF Power Control Range RF Power Range Control Resolution 20dB Bandwidth for modulated Carrier 2nd Adjacent Channel Power (+/- 2Mhz) 3rd Adjacent Channel Power (+/- 3Mhz) dBm dB dB kHz dBm dBm 0 16 Typ Max 2 35 1.8 879

-35

-45 4 1000

-20

-40 Bluetooth Spec

-6 to +4

> 16

< 1000

-20

-40 0.6.01 6 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application 7. Module Dimension and PCB Layout Guideline 7.1. Module Dimension m m 4 9

. 1 1 m m 3

. 7

5 x 6 4 1

. m m 1 4 2

. m m 1 8 3

. m m 4 5

. 2 7.2. PCB Layout Guideline 15mm 15mm ANTENNA CLEARANCE AREA m m 5 1 m m 5 1 m m 5

. 6 0.9mm 0.6mm 0.6.01 1.6mm 7 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help 8. FCC Statement NOTICE:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by ValenceTech Limited may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Radiofrequency radiation exposure information:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Please see the RF Exposure information. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device should be installed and operated with a minimum distance of 20cm between the antenna and all persons. Label requirements:

Contains Transmitter Module FCC ID: ORP-IBT-07 Host use instruction:

The module must install and work with a speaker, The speakers manufacturer is ValenceTech Limited. The Host mode name: IBT07 BLUETOOTH SPEAKER SYSTEM The Host Brand Name: ValenceTech The host is a fixed device and the antenna used with this host should be installed and operated with a minimum distance of 20cm from all persons. FCC RF Exposure Requirement 1. At least 20cm separation distance between the antenna and the users body must be maintained at all times. And must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi transmitter product procedures. 2. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed 0dBi in the 2.4G band. 3. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. Note: If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093. 0.6.01 8 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application Please be noticed following information and instructions should be placed in the end-

users operating manual The iBT-07 Module has been granted as limited modular approval for mobile applications. iBT-07 Module must be installed in the designated host as specified in this manual. 1. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. 2. The iBT-07 Module and its antenna must not be co-located or operating in conjunction with any other transmitter or antenna within a host device. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 3. A label must be affixed to the outside of the end product into which the iBT-07 Module is incorporated, with a statement similar to the following: For iBT-07:

This device contains FCC ID: ORP-IBT-07 4. The module shall be in non-detachable construction protection into the finished products, so that the end-user has to destroy the module while remove or install it. 5. This module is to be installed only in mobile or fixed applications. According to FCC part 2.1091(b) definition of mobile and fixed devices is:. Mobile device:

A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. In this context, the term fixed location means that the device is physically secured at one location and is not able to be easily moved to another location. Portable device:

For purposes of this section, a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. 6. Separate approval is required for all other operating configurations, including portable configurations with respect to FCC Part 2.1093 and different antenna configurations. 7. A certified modular has the option to use a permanently affixed label, or an electronic label. For a permanently affixed label, the module must be labelled with an FCC ID: ORP-IBT-07. The OEM manual must provide clear instructions explaining to the OEM the labelling requirements, options and OEM user manual instructions that are required For a host using a this FCC certified modular with a standard fixed label, if (1) the modules FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: Contains Transmitter Module FCC ID: ORP-IBT-07 or Contains FCC ID: ORP-IBT-07 must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. 8. Host product is required to comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion, compliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15B). To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. If a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, we suggest the host device to recertify part 15B to ensure complete compliance with FCC requirement: Part 2 Subpart J Equipment Authorization Procedures , KDB784748 D01 v07, and KDB 997198 about importation of radio frequency devices into the United States. 0.6.01 9 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application OEM RESPONSIBILITIES TO COMPLY WITH FCC REGULATIONS The iBT-07 Module has been certified for integration into products only by OEM integrators under the following conditions:

This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. OEM LABELING REQUIREMENTS FOR END-PRODUCT The iBT-07 module is labeled with its own FCC ID Certification Number. The FCC ID certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module. The final end product must be labeled in a visible area with the following:

Contains Transmitter Module FCC ID: ORP-IBT-07 or Contains FCC ID: ORP-IBT-07 The OEM of the iBT-07 Module must only use the approved antenna(s) listed above, which have been certified with this module. The device iBT-07 carries FCC authorization and is marked with the FCC ID Number. Whilst any device into which this authorized module is installed will not normally be required to obtain FCC authorization, this does not preclude the possibility that some other form of authorization or testing may be required for the finished device. OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093. The user manual for the end product must include the following information in a prominent location:

This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. The end product with an embedded FCC ID:ORP-IBT-07 Module may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15. The labeling instructions of finished products refer to following requirements:

A certified modular has the option to use a permanently affixed label, or an electronic label (see Electronic Labelling below). For a permanently affixed label, the module must be labelled with an FCC ID - Section 2.926 (see Certification (labelling requirements) above). The OEM manual must provide clear instructions explaining to the OEM the labelling requirements,options and OEM user manual instructions that are required (see next paragraph). 0.6.01 10 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application For a host using a certified modular with a standard fixed label, if (1) the module s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module:

Contains Transmitter Module FCC ID: ORP-IBT-07 or Contains FCC ID: ORP-IBT-07 must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. Other user manual statements may apply. 0.6.01 11 / 12 2012-11-29 iBT-07 Bluetooth Module for Audio Application Unit 1, 20/F., APEC Plaza, 49 Hoi Yuen Road, Kwun Tong, Hong Kong Valence Semiconductor Design Ltd. Tel: (852) 2797 3288 Fax: (852) 2776 7770 http://www.valencetech.com The information in this publication is believed to be accurate in all respects at the time of publication but is subject to change without notice. Valence Semiconductor Design Ltd. assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Valence Semiconductor Design Ltd. assumes no responsibility for the functioning of undocumented features or parameters. 0.6.01 12 / 12 2012-11-29