FCC ID: 2AONI-PRO-VTI01 PRO VT/PRO VTi safe

INSTRUCTION MANUAL Thank You For Your Recent Purchase At Vaultek we stand behind our product and you our customer. On behalf of the entire team thank you for your purchase. We believe personal defense should be handled seriously and we're excited for you to experience the ultimate performance in smart-security. VAULTEKSAFE.COM Table of Contents Product Overview. Introduction / Warnings Battery Operation / Battery Maintenance Battery Installation Charging the Battery-

Master Code Programming -

Remote Key Fob Operation / Warnings -

Remote Key Fob Pairing Toggle Key Fab Access Modes To Unpair Remote Key Fob Multiple Safe Management Hot Keys -

Tamper Detection -

Toggle Stealtn Mode Toggle Travel Made 01/02 03/04 05/07 05 2-06

. 08 09/12 09 10 10 at 13/14 13 15 B View Battery Sta B Toggle Interior Light - 1h Toggle Bluetooth - 1a Toggle Key Fob Modes - ua Toggle DMT Sensitivity Vaultek App / App Features -

Securing Your Safe __ 4 15/16

=. 17 Product Registration es ee 19 Troubleshooting --- 3 Customer Support / Warranty -_- 21 Box Contents Vaultek Pro VT Safe High Strength Steel Security Cable Remote Key Fob and Battery Hardware Mounting Kit AC Power Adapter Owner's Manual / Quick Start Guide Micro-USB Charging Cable Backup Keys (2) Tutorial Videos Listed below are some of the various tutorials available at vaulteksafe.cam How to Anchor Your Safe Hot Keys Available

+ More videos online. Installing Your Battery How to Register Your Safe Change Your Master Pin Code Overview of the Bluetooth App Product Overview Get to knaw your Vaultek safe, 01. Silicone Key Hole Cover 03. LED Status Bar 02. Micra-UUSB Charging Port 61 Vauitel 04, Pre-Drilled Mounting Holes 07. LED Light Button 05, Battery Compartment Door 08. LED Light 06. PROGRAM Button (Located Beneath Protective Cover) Vaultek App!

The Vaultek app is available for Android and iOS devices, The app allows you to remotely Unlock safe, check battery level, toggle sound ON/OFF, adjust the interior light, plus much more. See pages 15 to 16 far more information. Introduction The Vaultek Pro VT is a PIN access / Bluetooth access safe. Its solid structure and penetration resistant design makes it ideal for storing valuables such as firearms, jewelry, cash, and other personal items. Powered by a rechargeable lithium-ion battery, the safe combines high security with complete access control.

: How to open your Vaultek Safe. he numeric keypad responds quickly for rapid access and has a built-in proximity sensor that lights up when your hand brushes against the safe. See page 08 for more information. Key Fob: Remote for on demand access. See pages 09 anc 12 for more information. Vaultek App: Open the safe with the Bluetooth app. See pages 15 and 16 for more information. Key: Two keys are provided for manual access to the safe in the event the battery dies. Secure Defense: How your Vaultek Safe keeps people out. Anti-Impact Latches: Built to withstand forceful impacts and heavy slams. Unibody Construction: Our unibody design is extremely strong without welds or weak points. No External Access Points:

combination of interior mounted hinges and anti-pry reinforcement bars help prevent unwanted tools from attempting to break the safe open. Security Sleep Mode: Activates when six (6) consecutive incorrect keypad entries are entered and does not accept any entries for four minutes. A backup key or programmed fingerprint may be used to open the safe. DMT (Dynamic Motion Tracking): Motion activated alarm can be disabled or enabled with three levels of sensitivity (Low, Medium, and High) using the Vaultek app or hot key functions. See page 14 for information. 03 Vaultek Warnings To prevent damage to your Vaultek unit or injury to yourself or to others, read the following safety precautions before using this unit. DO NOT PLACE OR STORE THE BACKUP KEYS INSIDE THE SAFE AT ANY TIME. IF THE BATTERY FAILS, YOU WILL BE DO NOT expose to extreme heat or cold. Battery power may be affected. ALWAYS check to make sure coor has latched when closing; lid requires a firm press and locks automatically. DO NOT store loaded guns in this unit. SELLER NOR MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR THE INABILITY TO USE THE VAULTEK SAFE. ASSUMES ALL RISK AND LIABILITY WHATSOEVER IN CONNECTION THEREWITH. IMPORTANT Check page 12 for remote key fob warnings. 04 Vaultek Continue on newt page for more information about the battery. Battery Operation Your safe uses 2 3.7V 18650 rechargeable lithium-ion with a flat top. A minimum 2000 mAh capacity 15 required, hawever 2200, mAh or higher can be used to increase operation time. Battery Installation 1 To get started, insert one of your backup keys into the keyhole al the front of the sale (see Figure A). Push key in and rotate the key 90 degrees clockwise to open tne safe. 2 Remiove the interior padding. Locate the battery compariment door on the insice of the safe directly behind the '4' key on the keypad (see Figure B)) 3. Remove the battery cover by pressing dawn on the tab near the top of the cover. 4% insert the 18650 rechargeable lithium-ion pattery (included in accessory box) inte the battery compartment, Note thal your Vaultek safe automatically detects the polarity af the battery ang can be installed in either direction 5 When the battery is inserted you will hear a short welcome tone ang the keypad will light up. 6 Once you hear the tone and see the keypac light up, replace the battery cover. You are now ready to program your safe. IMPORTANT Your Vaulttck safe will automatically foclswhen you fully elose the itd

(05 Vauitek Charging the Battery Your Vaultek safe is powered by a rechargeable jthium-ion battery and comes with a charging kit which includes an AC power adapter (suitable far 120 volt power outlets) and a micro-USB cable. Safe and micro-USB cable can be used with all international power adapters. Under normal usage, a fully charged battery can ast at least 3 months, To recharge tne safe, plug the micro-USB cable into the micro-USB receiving jack located on the lower right side of the safe (Figure C) and connect to a standard USB port or wall outlet using the AC power adapter. Approximate recharge time is, 2.5 hours. During recharging, the white LEDs above the micro-USB jack (Figure C) indicate the oavtery capacity as below:

A lights glow: Fully recharged 3 lights glow, 2 light blinks: 80%-100%

2 lights glow, 2 light blinks: 60%-80%

2 light glows, 1 tight olinks: 40%-60%

4 light blinks, less than 20%

The charging kit can also function as an external power supply, which means you can open yoursate when the battery is depleted, IMPORTANT Atter installing the battery, use the charging kit provided to charge the unit 100%, Leaving your safe plugged in continually will not harmthe safe or battery. TUTORIALS ONLINE AT VAULTEKSAFE.COM 6 Vauitek Battery Maintenance Testing the Battery Power To check the battery level, press and hold the 6 and8' key together on the keypad for 5 seconds, The status bar from left 0 right will plow GREEN or RED to indicate the battery level Remaining Battery Capacity Level

\f 5 LEDs glow green; 80%-100%

4 LEDs glow green, 60%-80%

43 LEDs glow green. 40%-60%

if 2 LED glows green, 20%-40%

(f1 LED glows red: 2%-20%

{f1 LED blinks red: less than 2%

Low Battery if the first LED on the status bar blinks RED several times and you hear several rapid beeps when opening the safe, your battery level is critically (aw and your safe needis to be charged immediately TP

{nthe event the battery dies or a Soft reset js performed (battery remayal and installation) the safe will restore:

default settings for DMT, interior ight, sound, and the remote key fob, These settings will need to be readjusted, however the master cade will not be affected, JMPORTANT Replace the battery when one or more of the following occurs: 4) all four of the white LEDs above the micro-USB jack are blinking or 8) ittakes move than 4 tours to recnarge the battery. Use a 3 7V 18650 rechargeable lithium-ion battery with a flat fop, A minimum 2000 mAh capacity is required, however 2200 mish or higher can be Used to increase pperation time, The adapter used to charge the battery should output $W/2000mA or above when Using micro-USB. TUTORIALS ONLINE AT VAULTEKSAFE.COM 7 Vauttek Master Code Programming First time users should change the default code as soon as possible to prevent unauthorized access to your safe. You will also use this master code to pair the Vaultek app on your smartphone, so it snould be kept confidential. TIP: Code Requirements

+ Your cade can be a minimum of 4 and a maximum of 8 keypad entries.

+ Iwo keys cannot be pressed simultaneously

+ Programming a new cade will overwrite your previous code 1. Enter default code 1-2-3-4 on the keypac to open the safe. 2. With the safe open, press and hald the '' key then the

"PROGRAM" button together (3 seconds)(Figure D) until al status bar LEDs turn RED and let go 3 Enter your NEW master cade. 4 Press and hold the '1' key then the "PROGRAM" button together again (3 seconds) until all status bar LEDs turn RED anc let go. 5 Enter your NEW master cade a second time 6 Press and hold the '1 key then the "PROGRAM" button together a third time (3 seconds) untit the safe beeps and all status bar LEDs turn GREEN and let go. This tone confirms that the master code has been reset, F IF you make a mistake and the new code will not work, simply start over with step 2 08 Vaultek Remote Key Fob Operation Your Vaultek safe supports quick access with the included remote key fob. Take caution when using this feature and be responsible. Security can be compromised in the event the key fob is lost or stolen. Only pair the key fob after thoroughly understanding the inherent risks. IMPORTANT Before you can pair the key fob to your safe connect the pre-installed battery by remaving the pull tab from the side of the key fob (Figure E) Remote Key Fob Pairing Note: As a security measure to prevent accidental access, yau must press both sides of the fob simultaneously to activate referred to as a dual press. This dual press is required for the pairing process as well as anytime the key fob is used to open the safe. Following this procedure will pair the key fob to your safe. 1. Press and hold the 's' key then "PROGRAM" button together (3 secands) until all status bar LEDs blink GREEN. 2. Aim the fob toward the safe and press both sides of the fob together

(Figure F), if all the lights on the status bar glow GREEN, the fob is paired successfully; if all lights on the status Dar blink RED, the fob failed to pais in ths case, simply start over with step one. IMPORTANT The key fob functions in close proximity to safe and has a short range of approxmately feet (Figure F):

After pairing the xey fab will be immeciarely active to test functionality. and then turn off. Key fab will need to be setto either On Demand or Progressive mode see page 10 for mare information

(09 Vaultek on next page for mo Toggle Key Fob Access Modes After pairing you can toggle between access modes from the keypad ar Bluetooth app. To toggle from the keypad press and hold the 6! key then "PROGRAM" button together. The status bar will communicate as directed below. OFF - Status Bar LEDs Turn Solid RED. Progressive Entry Mode - Status Bar LEDs Blink GREEN Safe goes into sleep mode and will require you to Wake up the safe before using Key fob. You can wake up the safe by pressing any key or brushing your hand across the keypad of the sate (backlit Keys will turn RED). On Demand Entry Mode - Status Bar LEDs Solid GREEN This mode grants immediate access to your safe without having to wake It up WarningGn Demand Entry Mode can peri a safe in another room endfor out of sight, To reduce risieat an unattended open safe We recommend \sing Progressive Entry Made, On Demand Eniry Made requires significant power usage and cari greatly reduce operstion time. We suggest Setting tne key fab (a Progressive Fntty Mode to conserve battery, To Unpair Remote Key Fob NOTE: Disabling the remote key fob function from the app or keypad will NOT delete a paired fob from the safe's memory, In the event a key fab is lost or stolen, you can delete the lost fab from the safe's memory by using a couple different methods:

A Press and hold '5' Key then "PROGRAM" button together (3 seconds) until all status bar LEDs blink GREEN. This 's the same sequence used when initially pairing. After the status bar LEDs blink GREEN for 6 seconds the safe will delete a paired key foh from memary. B Anytime a new key fob is paired with the Safe, the previous fob will be erased from the safe's memory 10 Vauttek Remote Key Fob Operation Continued Multiple Safe Management A Multiple safes can pairwith the same key fab ut multiple key fobs can nat pair with one safe B Recommended setting when using the key fob 1s Progressive Entry Made. Additionally you can manage multiple safes through the Vaultel app. CAUTION when managing multiple safe within range. in On Demand Entry Made there is a chance you can open all safes Battery Replacement The pre-installed battery will last approximately two years before requiring replacement. When needed follow the steps below to complete replacement, 1 Carefully separate the remote body with a small coin or your hand starting near the top of the remote at the designated coin stot. 2 Remove old battery and install a new monel CR2032 battery (Figure G), 3 Assemble remote back together.

#2 Vauttelo Key Fob Warnings Take caution when using this feature and be responsible. Security can be compromised in the event the key fob is tost or stolen. Only pair the key fob after thoroughly understanding the inherent risks. WARNING anyone including children can access the safe via key fob. ALWAYS unpair the key fob in the event itis lost or stolen. WARNING On Demand Entry Mode can open a safein anather room and/or out of sight. To reduce risk of an Unattended open sate we recommend using Progressive Envy Mode IMPORTANT On Demand Entry Mode requires significant power usage and can greatly reduce operation time on a single charge We supgest Meeping the safe in Progressive Entry Mode. (f using On Demand Entry Mode try keeping the safe plugged in 2 Vauttek Tamper Detection Press and hoid '2' and '4"

sll? le) Toggle Stealth Mode Press and hold 't' ands!

s[el7ja Toggle Travel Mode Press and ho!

View Battery Status 43 Vaultek nd hold '6! and '8 cS - |

To check for tampering press and hold keys '2' and '4' together for 3 seconds, The status bar will glow RED to indicate tampering or GREEN to indicate no tampering. You can reset the tamper detection by opening the safe through one of the authorized entry points To toggle the sound ON/OFF press and hold keys '1! and '3' together for 3 seconds. If the stalus bar glows GREEN and beeps, the sound is ON; if the status bar glows RED, The sound is OFF. Save battery life by disabling the proximity sensor, fingerprint sensor, keypad, status bar, and Bluetoatn features. Jo toggle travel made ON/OFF press and hold keys 1!

and '8' together until the safe Deeps and tne status bar lights up. IFthe status bar glows RED and beeps, ine safe is disabled, if the status bar glows GREEN and peeps, the safe 1s operational To check the battery level press and hold keys '6" and '8! together for 3 seconds. The status nars will glow GREEN or RED to indicate the battery level. See pages 05 to 07 for more information Ii 5 LEDs glow green: 80%-100%

If @ LEDs glow green: 60%-B0%

If 3 LEDS glow green: 40%-60%

IF2 LEDs glow green: 20%-40%

If LED glows red: 2%-20%

IF LED blinks rea: less than 2%

Toggle Interior Light Press and hoid'5' and '7"

CET) i i) Toggle Bluetooth Press and hold '4' then

"PROGRAM" button:

nee Jogo!

Toggle Key Fob Modes Press and hold 6 then "PROGRAM" button EES EME |

Toggle DMT Sensitivity Press and hold.'7' then "PROGRAM"

button To toggle the interior tight ON/OFF press and hold keys 's' and.'7' together for 3 secands, With the light toggled to ON you can press the "LIGHT" button inside the safe to illuminate the light and can also adjust brightness in the app, (Fthe light is Soggled OFF zhe light will be disabled To toggle the Bluetooth ON/OFF press ancl nold the 4 key then "PROGRAM" button together for 3 seconds If the status bar Blows GREEN Bluetooth is ON, (F the status bar glows RED Bluetooth is OFF |F Bluetooth is toggled OFF all app functions will be disabled and your safe is undiscoverable;

The key fob has THREE modes: OFF, Progressive Entry Made, anc On Demanc Entry Mode. OFF disables remote access, Progressive Entry Mode requires that you press one key on the safe keypad first and then activate the key fob, On Demand Entry Mode grants immediate access when activating the key fab. Pressing and holding the 's' key then "PROGRAM" outton together for 3 secancs wilt allow you to toggle through each made from the keypad. You may also alternate modes in the Vauttek app. Your Vaultek safe nas a buill-in accelerometer and corresponding alarin that alerts of any attacking to your safe including bumps end impacts, DMT (Dynamic Motion Tracking). OMT js enabled by default and its sensitivity has three settings, low, Medium, and High. You can toggle through these settings by pressing and holding the '7' key then "PROGRAM" button together for 3 secands. If all FIVE lights on the status bar glow solid GREEN, the High setting is enabled; If FOUR lights on the status bar glow solid GREEN, the Medivim setting is enabled; if THREE lights on the status bar glow GREEN, the Low setting is enabled if all lights on the status bar glow RED, DMT is disabled (OFF) UA vauitek Vaultek App The Vaultek app lets you get the most out af your Vaultek safe. Using the app gives you access and control over features that are not possible using the keypad interface alone. Get the App Download and install the Vaultek app for free ftom the Google Play Store, or Apple Stare. IMPORTANT You jnust be within Sluerooth rangesnel connected ro your Vaulte\ sate before any of the features willTanction Pattern Lock The pattem lock is an added layer of protection to saleguard your safe and prevent unauthorized access In the event your phone is misplaced. To create a pattern lock, simply drag your finger along the screen to conniect at

(east 4 circles, This unique pattern will be required when opening the app Pair with Your Vaultek Safe Be sure to pair your safe to your smartphone as soon as possible to sync the systems, Once paired you will gain access to the safes settings to acjust, toggle, and track any changes made to the safe, Note, any changes made rior to the safe connecting to the app will reflect the time stamp fram the safes defautt clock, and may nat match your phones clock 1 From the device, make sure Bluetooth is ON and discoverable by ather devices. 2 Open the app, and fallow the steps to pair your safe App Features Remotely Unlock Safe While in Bluetooth range you can remotely open the safe Check Battery Level A battery meter shows the remaining battery power. Toggle Sound ON/OFF You can togele the system sounds ON/OFF Adjust Interior Light You can vary the brightness on the internal LED lignt from 0-100%. History Log Track the time and date changes were made to the safe. Those changes may inciude when someone uniocked the safe and how they unlocked the safe, any changes to the settings of the safe including brightness, sound, master coce changes, anc more. Toggle DMT Sensitivity Enabled by default DMT will alert you to any impacts to your safe: Adjust the sensitivity settings of the alarm between Low, Medium, and High or toggle DMT OFF. Toggle Key Fob Modes Alternate between key fob access modes OFF, Progressive Entry Mode, and On Demand Entry Mode, TUTORIALS ONLINE AT VAULTEKSAFE.COM Securing Your Safe Your Vaultek safe can be secured a few different ways. Included is a security cable to attach your safe to larger stationary objects. There are also mounting screws included to maunt the safe to a flat surface using the pre-drilled holes on the bottom Using the Security Cable 1 Loop the security cable around a secured object. 2. Run the end of the cable through the eye of the other end and pull tight around the abject. 3 Place the end of the security cable inside the fully enclosed quick release cable mount inside your Vaultek Safe as shown in (Figure H). 44 Make sure the safe closes with the cable secured inside the quick release cable mount. JOURE Using the Mounting Screws TIP: Make sure you nave enough clearance for the lid to open properly before mounting the safe. 1 Position the safe on a flat surface where yau want to isis IMPORTANT Use aipenicittecmark th Hotes tani Mounting the safe vertically so that the doot flips 3 Dallprottates upward Will resulcin incomplete opening of the sofe a lve ta weight The door will open if the safats 44 Position safe in place ane install screws through safe mounted so that the daor opens down ot to.the:side, inta pilot hales. Tighten screws. 7 Vault Product Registration Vaultek strangly encourages you to register your safe as soon as you receive it. Registration provides many benefits including technical support and ordering replacement keys should you misplace them. Your Vaultek safe has a unique product number on the inside of the battery dear and a 4-digit ID number engraved on the keys, You will need these numbers to register your safe. 2. Locate your product number. its printed on the first oage of this user manual and on tne back of the battery door (Figure 1/3). 2 Find your 4-digit ID number engraved on the keys (Figure K) 3 Please visit the Vaultek website at vauiceksafe,com and click Support tnen click Registration from the available options, 4 Enter the required infarmation in the form and click:

ubmit TUTORIALS ONLINE AT VAULTEKSAFE.COM 2B Vault Q:How do I secure the app?

A: The app has a built in security pattern Lock feature ta prevent sameone from opening your phone and accessing the safe, Refer ta page 15 for mote information Q: Can keep the safe plugged in at all times?

A: Leaving your safe plugged in continually will not harm the safe or battery. However, to preserve the battery life span for portability we suggest that you unplug accastonaily to allow tne battery ta cycle down, Q: What happens to the fingerprints that are stored in my Vaultek safe when the battery dies?

A: The safe retains all fingerprints in the event of battery feilure. Once the sower is restored by inserting the AC adapter cable, the unit will function as it dic before the power loss. Q: What type of battery does my Vaultek safe use?

A: Use a 3.7 18650 rechargeable lithium-ion nattery with a flat top, A minimum 2000 mAh capacity is required however 2200 mAh or higher can be used ta increase operation time. This type battery is commonly available and in the event yau do not seek Vaultek fara replacement we recammend a brand name like Panasonic. Q: What happens if | lose the keys?

A First, make sure you registered your safe in tne event you do lose your keys, Cantact us at suppart@vaulteksafe.com. Be prepared to ravide your order details and product number to Us so we can verify ownership, Q: Can | travel with my Vaultek" safe through US Customs or TSA Security at the airport?

A: Yes, there are no restrictions on carrying this type of item. if transporting firearms make sure to check the safe or incluce with your checked baggage. Please ne aware that you may be asked to open your safe. Rather than pass it through x-ray, anc we recommend that an enrolled user be present during the transport of this item in case such a request is mace by a government authonty STOP! Do riot return to retailer. IF you have any questions about your Vaultek safe ot need ne'p configuring the system, please cantact us at suppart@vaulteksafe.com 9 Vauitek Troubleshooting

\F you experience any issues with yaur safe, try the following salutions. The app history clock data does not match up with my phones clock. A: The safe's internal clack will sync with your phone automatically when paired, All previous history, before the sync, will appear from the sefe's default clock and may not match your phone's clock. The keypad is not responding. A. Remove the battery and reinstall. This sa Soft reset for the safe, See if yau are able to open the safe using the default code 1-2-3-4 or even reorogram the safe's master cove, IF you are still experiencing issues contact Us at support@vauiteksafe.com The lid is not engaging. A: The tid requires a firm press. You will f the latches engage if you press slowly, Feel/listen for the click. Lights not working.

{A:To toggte the interior light ON/OFF press and hold keys 'S' and '7' together for 3 secands. With the light toggled to ON you can press the "LIGHT" button insice the safe to illuminate the light. f the light does not perform da a soft reset. Remove the battery and reinstall. This is a soft reset for the safe. If you are still experiencing issues contact us at support@vaulteksafe.com Q: What happens if | lose the keys?

A Fitst, make sure you registered yaur safe in the event you do lose your Keys, Cantact us at suppart@vaulteksafe.com. Be prepared to provide yaur order details and product number to us 50 we can verify ownership. Unable to change master pin code. A: Refer to page 08 of the user manual or check our tutorials online at vaulteksafe.com Under Support/ Tutorials Soft Reset: Remaye the battery and reinstall. This is 4 sofs reset for she safe, See page 07 for mate deteils 20 Vaultek Customer Support / Warranty Customer Support If you have a problem with your Vaultek safe that is not answered in the FAQ section of this manual, we encourage you to email us: SUPPORT@VAULTEKSAFE.COM, Warranty VAULTEK IS COMMITTED TO PROVIDING PRODUCTS OF KIGH QUALITY AND VALUE AND MAKES EVERY EFFORT Vaultek guarantees your safe will be free of defects in materials or workmanship for a period of one year from the date of original purchase from an authorized dealer. This warranty does not cover abuse, misuse, use in any manner for which is not designed, neglected, modification, damage, inadvertently caused by the user, accidents, and/or tampering. lf your safe is determined to be defective, we wi'l at our discretion, have it repaired: at our expense, or will send you a new one at no cost to you. You will be required to return your existing unit as well as all included parts to Vaultek prior to replacement along with your proof of purchase, If it is determined your safe needs to be returned, a Vaultek agent will provide a Return Authorization Number. Please have the following information available when you contact us:

-Purchaser's name, mailing address, email address, and a phone number.

-Copy of receipt

-Authorized Dealer Name

-Detailed description of problem NEITHER SELLER NOR MANUFACTUI SHALL BE LIABL R ANY INJURY, LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR THE INABILITY TO USE TKE VAULTEK SAFE, 21 Vaultek The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction FCC statements:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. 37 North Orange Ave. Sujte 800B Orlando, FL 32801

INSTRUCTION MANUAL Thank You For Your Recent Purchase At Vaultek we stand behind our product and you our customer. On behalf of the entire team thank you for your purchase. We believe personal defense should be handled seriously and we're excited for you to experience the ultimate performance in smart-security. Table of Contents 01/02 03/04 05/07 Product Overview. Introduction / Warnings Battery Operation / Battery Maintenance Battery Installation 05 Charging the Battery 06 Master Code Programming 08 Smart Align Biometric Programming 09/12 Helpful Programming TIPS _.. Programming 1st and 2nd Fingerprints. Programming Additional Fingerprints -

09 10 Bey Deleting Fingerprints -.-------------- 12 Remote Key Fob Operation / Warnings 13/16 Remote Key Fob Pairing 3 Toggle Key Fob Access Modes _ a To Unpair Remote Key Fob m%

Multiple Safe Management 15 Hot Keys ---- 16/18 Tamper Detection - 16 16 17 v7 ay vy Toggle Stealth Mode Toggle Travel Made View Battery Status -

Delete Fingerprints -

Toggle Interior Light 18 18 Toggle Bluetooth _ Toggle Key Fod Modi Toggle DMT Sensitivity Toggle Dual Entry Mode Vaultek App / App Features _ Securing Your Safe ____ Product Registration FAQ __ Troubleshooting ______ Customer Support / Warranty Box Contents Vaultek Pro VTi Safe High Strength Steel Security Cable Remote Key Fob and Battery Hardware Mounting Kit AC Power Adapter Owner's Manual / Quick Start Guide Micro-USB Charging Cable Backup Keys (2) Tutorial Videos Listed below are some of the various tutorials available at vaulteksafe.com, Installing Your Battery Overview of the Bluetooth App How to Register Your Safe How to Anchor Your Safe Change Your Master Pin Code Hot Keys Available How to Program Your Fingerprint + More videos online, Product Overview Get to know your Vaultek safe 01. Smart Align Biometric Scanner 03. Micra-USB Charging Port 02. Silicone Key Hole Cover 04, LED Status Bar 91 Vaultel 05. Pre-Drilled Mounting Holes 08. LED Light Button 06. Battery Compartment Door 09. LED Light 07. PROGRAM Button (Located Beneath Protective Cover) Vaultek App!

The Vaultek app is available for Android and i0S devices. The app allows you to remotely unlock safe, check battery level, toggle sound ON/OFF, adjust the interior light, name fingerprint IDs, plus much more. See pages 19 ta.20 for more information. 2 Vaulteam Introduction The Vaultek Pro VTi is a biometric, PIN access / Bluetooth access safe. Its solid structure and penetration resistant design makes it ideal for storing valuables such as firearms, jewelry, cash, and other personal items. Powered by a rechargeable lithium-ion battery, the safe combines high security with complete access control. Secure Acces:

How to open your Vaultek Safe, Smart Align Biometric Scanner: Personalized access for up to 20 unique fingerprint. See pages 09 to 12 for more information. he numeric keypad responds quickly for rapid access and has a built-in proximity sensor that lights up when your hand brushes against the safe. See page 08 for more information. Key Fob: Remote for on demand access. See page 13 and 16 for more information. Vaultek App: Open the safe with the Bluetooth app. See pages 19 and 20 for more informati Key: Two keys are provided for manual access to the safe in the event the battery dies. How your Vaultek Safe keeps people out. Anti-Impact Latches: Built to withstand forceful impacts and heavy slams. Unibody Construction: Our unibody design is extremely strong without welds or weak points. No External Access Points: A combin:

tion of interior mounted hinges and anti-pry reinforcement bars help prevent unwanted tools from attempting to break the safe open. Security Sleep Mode: Activates when six (6) consecutive incorrect keypad entries are entered and does not accept any entries for four minutes. A backup key or programmed fingerprint may be used to open the safe. DMT (Dynamic Motion Tracking): Motion activated alarm can be disabled or enabled with three levels of sensitivity (Low, Medium, and High) using the Vaultek app or hot key functions. See page 18 for information. 03 Vaultek Warnings To prevent damage to your Vaultek unit or injury to yourself or to others, read the following safety precautions before using this unit. DO NOT PLACE OR STORE THE BACKUP KEYS INSIDE THE SAFE AT ANY TIME. IF THE BATTERY FAILS, YOU WILL BE DO NOT get the fingerprint sensor area wet. DO NOT expose to extreme heat or cold. Battery power may be affected. ALWAYS check to make sure door has latched when closing; lid requires a firm press and locks automatically. DO NOT store loaded guns in this unit. SELLER NOR MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT OR ASSUMES ALL RISK AND LIABILITY WHATSOEVER IN CONNECTION THEREWITH. IMPORTANT Check page 16 for remote key fob warnings. 04 Vaultek Battery Operation Your safe uses @ 3.7V 18650 rechargeable lithium-ion with a flat top. A minimurn 2000 mAh capacity is required, hawever 2200 mAh or higher cafy be used to increase operation time, Battery Installation 1 To get started, insert one of your backup Keys into the keyhole at the frontof the safe (see Figure A). Push key in and rotate the key 90 degrees clockwise to open the safe. 2. Remove the interior padding, Locete the battery compartment door on the inside of the safe directly behind the '4' key on the keypad (see Figure 8). 3 Remove the battery cover by pressing down on the tab near the top of the cover, 4 Insert the 18650 rechargeable lithium-ion battery (Included in accessory box) into the battery compartment, Note that your Vaultek safe automatically detects the polarity of the battery and can be installed in either direction, 5 When the battery is inserted you will hear a short welcome tane and the Keypad will light up 6 Onice you hear the tone and see the keypad light up, replace the battery cover, You are now ready to program your sate IMPORTANT Your Vaultek safe will automatically lock when you fully close the tid.

(05 Vaultek Continue on next page for more information about the battery. Charging the Battery Your Vaultek safe is powered by a rechargeable ithium-ion battery and comes with a charging kit Which includes an AC power adapter (suitable for 120 volt power outlets) and a micra-USB cable. Safe and micro-USB cable can be used with all international power adapters. Under normal usage, a fully charged battery can

{ast at least months, fo recharge the safe, plug the micro-USB cable into the micra-USB receiving jack located on the (ower right side of the safe (Figure C) anc connect to a standard USB port or wall outlet using the AC power adapter. Approximate recharge time is 2.5 hours. During recharging, the white LEDs above the micro-USB jack (Figure C) indicate the battery capacity as below: IMPORTANT Alter instaliing the battery, use the charging kit 4 lights glow: Fully recharged provided to charge the unit 100%. 3 lights glow, 2 light blinks: 80%-100%

2 lights glow, 2 light blinks: 60%-80%

1 light glows, 1 light blinks: 40%-60%

light blinks, less than 20%

Leaving your safe plugged in continually will not harm the sale or battery. The charging kit can also function as an external power supply, which means you can open your safe when the pattery is depleted TUTORI:

'S ONLINE AT VAULTEKSAFE.COM 6 Vauitek Battery Maintenance Testing the Battery Power To check the battery level, press and hold the 6 and8! key together on the keypad for 3 seconds, The status bar from left to right will glow GREEN or RED ta indicate the battery \evel Remaining Battery Capacity Levet Low Battery IF 5 LEDS glow green: 80%-100%

\f 4 LEDs glow green: 60%-80% If the first LED on the status bar blinks RED severa

(f 3 LEDs glow green: 40%-60% times and you hear several rapid oeeps when opening

{f 2 LED glows green 20%-40% the safe, your battery level is critically low and your

\F 1 LED plows red; 2%-20% safe needs to be charged immedia

\F 1 LED blinks red: ess than 2%

Tr

{nthe event the battery dies ora soft reset is cerformed (battery remaval and installation) the safe will restore defaulcsettings for DMT, interior light, sound, and the remote key fob, These settings will necd to be readjusted, however fingerprint JDs and master cade will not be affected IMPORTANT Replace the battery when one ar more of the following occurs: A) alt four of the white LEDs above che micro-USB. Jack are blinking or 8) it takes more than4 hoursto recharge the battery. Use a 5,7\/ 28650 rechargeable lithium-ion battery with a flat top. A minimum 2000 mAh capacity is required, however 2200 mAh or higher can be used ta increase operation time. The adapter used to charge the battery should output 5W/2000mA or above when using micro-USB, TUTORIALS ONLINE AT VAULTEKSAFE.COM 7 Vauttek Master Code Programming First time users should change the default code as soon as possible to prevent unauthorized access to your safe. You will alsa use this master code to pair the Vaultek app on your smartphone, so it should be kept confidential, TIP: Code Requirements

+ Your code can be a minimum of 4 and a maximum of 8 keypad entries.

+ Iwo keys cannot be pressed simultaneously

+ Programming a new cade will overwrite your previous cooe 1 Enter default cade 1-2-3-4 on the keypac to open the safe. 2 With the safe open, press and hald the '1' key then the

"PROGRAM" burton together (5 seconds)(Figure D) until all status bar LEDs turn RED and let go, 3 Enter your NEW master cade. 4 Press and hold the 1 Key then the "PROGRAM" button tagether again (3 seconds) until all status bar LEDs turn RED and let go. 5 Enter your NEW master cade a second time 6 Press and hold the t key then the "PROGRAM" button together a third time (3 seconds) until the safe beeps and all status bar LEDS turn GREEN and let go. This tone confirms that the master code has been reset E If you make a mistake and the new cade will nat work, simply start over with step 2 108 Vaultek Smart Align Biometric Programmin, Biometrics are methods of authenticating the identity of a person base on physical or behavioral characteristics. Biometric Fingerprint authentication refers to technology that measures and analyzes human physical characteristics for identification and authentication purposes. The smart align biometric system guides Yyour finger placement for consistent and accurate results. Everyone has their awn unique fingerprints, and what makes them unique isthe pattern of ridges, valleys, and minutiae paints that comprise an individual print. Vaultek and their leading engineering group has developed proprietary technology to read and match fingerprints with unmatched speed and accuracy. That means that only authorized Users have access to your valuables. The safe is capable of storing fingerprint data for up to 20 unique authorized users. A user consists of 5 scans of the same finger during registration. Once a user's fingerprint data

's stored in the safe and encrypted, it cannot be copied or stolen. Helpful Programming TIPS =

}* Place cuticle of finger aver center of scanner in line with | |

| side LEDs (this allows the scanner to read where mast of |

| the fingerprint detail is (ocated) see (Figure E + F). i Adjust your finger slightly between scans for increased accuracy. Excessive moisture, lotions, or dirt will affect your fingerprint and may cause inaccurate sensor reading, If you are experiencing difficulty try different fingers. Each finger is unique and some fingers, such as your thumb, contain more readable information than others i FIGURE G ATTENTION! (FIGURE G)

| + To increase success rate register the same finger i

| multiple times. | Position your finger flat against the scanner to i increase the amount of readable information 09 Vaulhes Continue on next page for more information about the fi Programming the 1st and 2nd Fingerprints The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize adcitional users Open the safe Program ist fingerprint by pressing and holding the '2' key then the "PROGRAM" button together

[3 seconds)(Figure H) until the first LED on the status bar located above the fingerprint sensor (Figure |) blinks RED. Using the helpful programming tips provided on page 09 place your finger on the fingerprint scanner for the first of 5 scans. When the safe beens and the first status bar LED lights up GREEN remove your Ainger, If the status bar LED turns RED then remove your finger and reposition the Finger on the fingerprint scanner. Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift You Will repeat this process untib all status bars (1-5) are solid GREEN Close lid and test to see if the safe will open using your Fingerprint. If you experience issues refer to the neipful programming tips listed on page 09 ar check our tutorials online at vaulteksafe,com under Support/Tutorials. Repeat steps 1 through 4 to add the 2nd administrative Fngerorint. to Vauinek Programming Additional Fingerprints The first two fingerprints programmed into the safe are the administrative fingerprints. Any additional users programmed require authorization from one of these fingerprints. Open the safe. Program additional fingerprints by pressing and holding the '2' then "PROGRAM" button together

(3 seconds)(Figure H on page 10). The entire status bar will blink RED prompting you to scan one of the administrative fingerprints. Place one of the first two programmed administrative fingerprints on the scanner and remove when the safe beeps and the entire status bar blinks GREEN. When the first LED on the status bar starts blinking RED you can program a NEW fingerprint. TIP: If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the safe again and not the NEW fingerprint. If this happens start over with step one. Using the helpful programming tips provided on page 09 place the NEW finger on the scanner. When the safe beeps and the first LED in the status lights up GREEN remove your finger. Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bar LEDs (1-5) are solid GREEN. TUTORIALS ONLINE AT VAULTEKSAFE.COM 11 Vaultek Deleting Fingerprints individual fingerprint can not be deleted from the keypad on the safe. Following this procedure will erase all of the fingerprints including both administrative fingerpri:

If you wish to delet individual fingerprints, you must use the Vaultek app. This procedure will not affect the keypad master code. Press and hold the '3' key then the "PROGRAM" button together until all le status bar LEDs light up RED and let go. ter your master code on the keypad. If the code is correct, all the status bar LEDs will blink GREEN and safe will beep indicating deletion of all of the fingerprints. 12 Vaultek Remote Key Fob Operation Your Vaultek safe supports quick access with the included remote key fob. Take caution when using this feature and be responsible. Security can be compromised in the event the key fob is lost or stolen. Only pair the key fob after thoroughly understanding the inherent risks. :

IMPORTANT Before you can pair the Key fob to your safe connect the pre-installed battery by removing the pull tab from the side of the key fob (Figure 7}

Remote Key Fob Pairing Note: As a security measure to prevent accidental access, you must press both sides of the fob simultaneously to activate referred to as a dual press. This dual press is required for the pairing process 2s well as anytime tne key fob is used to open the safe. Following this j procedure will pair the key fob to your safe. FIGURE 1 1. Press and hold the 's' key then "PROGRAM" button together (3 secands) Until all status bar LEDs blink GREEN, 2. Aim the fob toward the safe and press both sides of the fob together

(Figure \). If all the lights on the status bar glow GREEN, the fob is. paired successfully; if all lights on the status bar blink RED, the fab failed to pair in this case, simply start over with step one, IMPORTANT The key feb functions in close proximity to safe and has a short range of aparoximaiely 5 feet (Figure K}) Afterpainng the key fob will be immediately active zo test functionality and then turn off. Key fob will need to be sez to either On Demand or Progressive made see page 24 for more information. 3 Vaultek on next page for more inforn Toggle Key Fob Access Modes After pairing you can toggle be press and hold the 6 key ther OFF - Status Bar LEDs Turn Solid RED Progressive Entry Mode - Status Bar LEDs Blink GREEN Safe goes into sleep mode and will require you to wake up the safe before using key fob. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED). sween access modes fram the keypad or Bluetooth app. To toggle fram the keypad

"PROGRAM" button together. The status bar will communicate as directed below. On Demand Entry Mode - Status Bar LEDs Solid GREEN This mode grants immediate access to your safe withaut having to wake it up. Warning: On Demand Entry Made can open a safe in) another room and/or out of sight To reduce risk of an unattended open safe we recommend using Progressive Entry Mode:

On Demand Entry Mode requires significant power usage anc can greatly reduce operation time, We Suggest setting the key fob ta Progressive Entry Made ta conserve battery, To Unpair Remote Key Fab NOTE: Disabling the remote key fob function from the app or keypad will NOT delete a paired fob from the safe's memory. In the event a key fab is lost or stolen, you can delete the lost fob from the safe's memory by using a couple different methads:

A Press and hold '5! key then "PROGRAM" buttons together (3 seconds) until all status bar LEDs blink GREEN. This is the same sequence used wher initially oairing. After the status bar LEDs blink GREEN for 6 seconds the safe will delete a paired key fob from memory. B Anytime a new key fob is paired with the safe, the previous fob will be erased from the safe's memory. a Vauitek Remote Key Fob Operation Continued Multiple Safe Management A Multiple safes can pairwith the same key fob out multiple key fobs can not pair with one sate. B Recommended setting when using the key fob is Progressive Entry Mode. Additionally you can manage multiple safes through the Vaultek app. CAUTION wnen managing multiple safes in On Demand Entry Mode there is a chance you can open all safes within range. Battery Replacement The pre-installed battery will last approximately two years before requiring replacement. When needed follow the steps below to complete replacement. 1 Carefully separate the remote body with a small coin or your hand starting near the top of the remote at the designated coin stot 2 Remove old battery and install a new model CR2032 battery (Figure L) 3 Assemble remote back together IGURE |

5 Vaultek Key Fob Warnings Take caution when using this feature and be responsible. Security can be compromised in the event the key fob is lost or stolen. Only pair the key fob after thoroughly understanding the inherent risks. WARNING anyone including chileren can access the safe via key fob ALWAYS unpair the key fob in the event itis lost or stolen WARNING On Demand Entry Mode can open a safe in another room andior aut af sight, To reduce isk of an unattended open safe we recommend using Progressive Envy Mace. IMPORTANT On Demand Entry Made requires significant power Usage and can greatly recuce operation time ona single charge We suggest keeping the safe in Progressive Entry Mode. If using On Demand Entry Made try keeping the safe plugged in. Hot Keys continued on next page Tamper Detection To:check for tampering press anc hold keys '2' and 4 together for 3 seconds, The Press and hald '2' and 4 _ status bar will glow RED to indicate tampering or GREEN ta indicate no tampering

(RB Bh [fe [2fe) You san reset the tamper detection by opening the safe througn one of tne en AIA) authorizec entry points Toggle Stealth Mode _o toggle the sound ON/OFF press and hold keys '1' and 's! together for 3 seconds. If Press and hald'1 ands the status bar glows GREEN and beeps, the sound is ON; if tne status bar glows RED, We ss le[z]e) the souncis ore Le Vauivek Hot Keys Toggle Travel Mode Press and hold '1! anda"

| SESS EAIED = |

View Battery Status Delete Fingerprints Press and hold 3' then PROGRAM" button then enter master code CE EGGTDT Toggle Interior Light Press and hale '5' and '7"

o-B:

27 Vauleek Save battery life by disabling the proximity sensor, fingerprint sensor, keypad, status ar, and Biuetootn features, To togele travel mode ON/OFF press and hoid keys '1'

ana '8! together until the safe beeps and the status bar lights Up. Ifthe status bar glows RED and beeps, the safe is disabled if the status bar glows GREEN and beeps, the safe is operational To check the battery level press and hold keys '6! and '8! logether for 3 seconds. The status bars will glow GREEN or RED to indicate the battery level. See pages 05 to 07 for more information IF5 LEDs glow green: 80%-100%

If LEDs giow green: 60%-80%

If 3 LEDs giow green: 40%-60%

(72 LEDS plow green: 20%-40%

{71 LED glows red: 2%-20%

17-1 LED blinks red: less than 2%

To delete fingerprints press and hala the 's' key tnen "PROGRAM" button togetner until all status dar LEDs light up RED then enter your master cade. This will remove all the fingerprints. You can delete indivicual fingerprints in the Vaulteke app. To toggle the interior light ON/OFF press and hold keys '5' and '7' together for 3 seconds, With the lignt toggled to ON you can press the "LIGHT" buttan insie the safe to illuminate the tight anc can also adjust brightness in the app, Ifthe light is toggled OFF the light will be disablec. Toggle Bluetooth Press and hold '4' then

"PROGRAM" button Ie Toe Toggle Key Fob Modes Press and hold '6'

then "PROGRAM" button

(RES EV ESCO ~ EAC Toggle DMT Sensitivity Press and hola7! then "PROGRAM"

button Gl Toggle Dual Entry Made Press and hold '8! then,

"PROGRAM" button e}o[+

To toggle the Bluetooth ON/OFF press and hala the '4' key then "PROGRAM" button together for 3 seconds. ifthe status bar glows GREEN Bluetooth is ON. Ifthe status bar glows RED Bluetooth js OFF If Bluetooth is toggled OFF all app functions will be disabled and your safe is undiscoverable. The key fob has THREE modes: OFF, Progressive Entry Mode, and On Demand Entry Mode. OFF disables remote access Progressive Entry Mode requires that you press one key an the safe keypad first and then activate the key fob. On Demand Entry Mode grants immaciate access when activating the key fob. Pressing and holding the '6! key then "PROGRAM" buttan together for 3 seconds will allow you to toggle through each made from the keypad, You may also alternate modes in the Vaultek app, Your Vaultek safe has a built-in accelerometer and corresponding alarm that alerts of any attacking to your safe including bums and impacts, DMT (Dynamic Motion Tracking), DMT is enabled by default and its sensitivity has three settings Low, Medium, and High, You can toggle through these settings by pressing and holding the '7' key then "PROGRAM" button sogether for 3 seconds fall FIVE lights on the status bar glow solid GREEN, the High setting is enablea; If FOUR lights on the status bar glow solid GREEN, the Medium setting is enabled; if THREE lights on the status bar glow GREEN, the Low setting is enabled if all lignts on the status bar glow RED, DMT is disabled (OF?) To toggle the Dual Entry ON/OFF piess and hold the '8' Key then "PROGRAM"

button together for 3 seconds. if the status tar glows GREEN, this features is ON. If the status bar glows RED this features is OFF If the Dual Entry is (oggled ON, you will be required to enter your master code and fingerprint {and vice versa} to open tne sate. 18 Vauitek Vaultek App The Vaultek app lets you get the most out af your Vaultek safe. Using the app gives you access and cantral over features that are not possibie using the keypad interface alone Get the App Download and install the Vauitele app for free from the Google Play Store, or Apple Store IMPORTANT You must be within Bluetooth range ancl connected to your Vaultek saie before any of the features willfunction Pattern Lock The pattern lock is an added tayer of protection to safeguard your safe and preventt unauthorized access in the evert your phone is misplaced, To create a pattern lock. simply crag your finger along the screen to connect at east 4 circies, This unique pattern will be required when opening the apa, Pair with Your Vaultek Safe Be sure ta pair your safe to your smartphone as soon as possible to sync the systems. Once paired you will gain access to the safes settings to adjust, toggle, and track any changes mace to the safe. Nove, any changes mace prior to the safe connecting ta the app will reflect the time stamp from the safes default clock, and may not match your phones clock 1 From the device, make sure Bluetooth is ON and discoverable by other devices. 2 Open the app, and follow the steps to pair your safe:

9 Vauitek Remotely Untock Safe While in Bluetooth range you can remotely open the safe Check Battery Level A battery meter shows the remaining battery power Toggle Sound ON/OFF You can toggle the system sounds ON/OFF. Adjust Interior Light You can vary the brightness on the internal LED light fram 0-100%. Manage Fingerprint IDs Name each fingerprint that is programmed inta the safe, and also delete a single fingerprint or all of the fingerprints History Log Track the time and date changes were made to the safe. Those changes may include when someone unlockee the safe and now they unlocked the safe, any changes to the settings of the safe including brightness, sound, master code changes, any deleted users, and more Toggle DMT Sensitivity Enabled by default DMT will alert you to any impacts to your safe, Adjust the sensitivity settings of the alarm between Low, Medium, and High or toggle OMT OFF Toggle Key Fob Modes Alternate between key fob access mades OFF, Progressive Entry Mode, and On Demand Entry Mode. Dual Entry Mode An optional secunty feature that requires an autnorized user to enter eitner the master code firs, then scan a programmed fingerprint or fingerprint then master code to open the safe TUTORIALS ONLINE AT VAULTEKSAFE.COM Securing Your Safe Your Vaultek safe can be secured a few different ways. Included is a security cable to attach your safe to larger stationary objects. There are also mounting screws included ta maunt the safe to a flat surface using the pre-drilled holes on the bottom Using the Security Cable T

it 1. Loop the security cable around a secured object 2 Run the end of the cable through the eye of the other end and pul tight around the abject. 3 Place the end of the security cable inside the fully enclosed quick release cable mount inside your Vailltek safe as shown in (Figure M]. 4 Make sure the safe closes with the cable secured inside the quick release cable mount. Using the Mounting Screws TIP: Make sure you nave enough clearance forthe lid to open properly before mounting the safe 4 Position the safe on a flat surface where you want to cia: IMPORTANT Mounting the safe verticalty so that the door flips upward will resulcin incomplete opening of the safe due te weight. The door will open ifthe safe is maunited so that the door opens down or ta the side, 2 Use a pencil to mark the holes for drilling, 3 Drill pilot holes, 4 Position safe in place anc install screws through safe into pilot hales. Tighten screws 21 Vauttek Product Registration Vaultek strangly encourages you to register your safe as soon as you receive it. Registration provides many benefits including technical support and ordering replacement keys should you misplace them. Your Vaultek safe has a unique product number on the inside of the battery dear and a 4-digit ID number engraved on the keys, You will need these numbers to register your safe. 2 Locate your product number itis printed on the first page of this user manual and on the back of the battery door (Figure N/O). 2 Find your 4-digit ID number engraved on the keys (Figure P) 3 Please visit the Vaultek website at vaulteksafe,com ano click Suppor: then click Registration From the available options, 44 Enter the required information in the form and click submit

{ FGUREO P/N-XXXXXXXXXXKK FIGURE N TUTORIALS ONLINE AT VAULTEKSAFE.COM 22 Vaultek App

(Q: How do I secure the app?

A.The apo has a built in Security pattern lock feature to prevent someone from opening your phone and accessing the safe, Refer ta page 19 for more information. Battery Q: Can keep the safe plugged in at all times?

A: Leaving your safe plugged in continually will not harm the safe or battery. However, to preserve the battery life span for portability we suggest that you unplug occasionally to allow the battery to cycle clown, Q: What happens to the fingerprints that are stored in my Vaultek safe when the battery dies?

Ac The safe retains all fingerprints in the event of battery failure, Once the power is restored by inserting the AC adapter cable, the unit will function as it did before the power loss Q: What type of battery does my Vaultek safe use?

A: Use a 3.7V 18650 rechargeable lithium-ion battery with a flat top, A minimum 2000 mAh capacity is required however 2200 mAh or higher can be used ro increase operation time, This type battery is commonly available and inthe event you do not seek Vaultek fora replacement we recommend a brand name like Panasonic Q; Can | use a battery of more than 2000mAh?

Ac Yes, a minimum 2000 mAh cepacily is required, however 2200 mAh or higner can be used to increase aperation time. Fingerprint Scanner Q; How do | improve fingerprint success rate?

A Refer to page 09 for lips TUTORIALS ONLINE AT VAULTEKSAFE. 23 Vaultek Q:If I cut my finger, does the fingerprint heal the same as before and will it open my safe?

A: Usually yes, although if the cut is significant or requires stitches scar tissue may form as a result causing a cchange in your fingerprint. That is why we recommend enrolling additional user fingerprints and alsa fingerprints from your other hand. Q: Will my Vaultek safe scan my finger correctly when my finger/fingerprint is wrinkled after bathing or swimming?

AcThe Vaultek safe has been designed to be very sensitive when authenticating and matching fingerprints. The untilwill open when your fingerprint has increased moisture from an average shower or swim. However, extreme water retention due to extended time in the water will cause aspects of yaur fingerprint to change for a short period. If this happens, fingerprint access to your safe may be denied until your fingerprint returns to its normal condition. Tne keypad and app will nat be affected and will still function normally to open the safe. Key

: What happens if! lose the keys?

A: First, make sure you registered your Safe in the event you do lose your keys. Contact us at Support@vaulleksafe.com, Be prepared to provide your order details and produict number (0 us So We can verify ownership, Misc. Q: Can | travel with my Vaultek safe through US Customs or TSA Security at the airport?

A: Yes, there are no restrictions on carrying this type of item If transporting firearms make sure to check the safe or include with your checked baggage. Please be aware that you may be asked ta open your safe. Rather than pass it through x-ray, and we recommend that an enrolled user be present during the transport of this item in case Such a request is made by a government authority, Dan't See yur question answered Send us your question (6 support@vauilleksafe.com 24 Vaulteke Troubleshooting if you experience any issues with your safe, try the following solutions. App The app history clock data does not match up with my phones clock. A: The safe's internal clock will sync with your phone automatically when paired. All previous history, before the sync, will appear from the safe's default clock and may not match your phone's clock. Fingerprint Scanner Attempted to program but the light above the scanner does not turn on. A: Remove the battery and reinstall. This is a soft reset for the safe. Fingerprint scanner works sometimes and not others. A: We have a few suggestions to help improve the success rate on page 09, Keypad The keypad is not responding. A. Remove the battery and reinstall This is a soft reset for the safe. See if you are able to open the safe using the default code 1-2-3-4 or even reprogram the safe's master code. If you are still experiencing issues contact us at support@vaulteksafe.com The lid is not engaging. A: The lid requires a firm press. You will feel the latches engage if you press slowly. Feel/listen for the click. 25 Ve stek Lights Lights not working. rior lignt ON/OFF press and nold keys 'S' and '7' together for 3 seconds. With the light toggled to ON you can press the "LIGHT" button inside the safe to illuminate the light. If the light does not perform do a soft reset. Remove the battery and reinstall. This is a soft reset for the safe. If you are still experiencing issues contact us at support@vaulteksafe.com. Master Piri ode Unable to change master pin code. A: Refer to page 08 of the user manual or check our tutorials online at vaulteksafe.com under Support/Tutorials. Remove the battery and reinstall. This is a soft reset for the safe. See page 07 for more details. STO!

/o not return to retailer. If you have any questions about your Vaultek safe or need help configuring the system, please contact us at support@vaulteksafe.com. TUTORIALS ONLINE AT VAULTEKSAFE.COM 26 Vaultek Customer Support / Warranty Customer Support If you have a problem with your Vaultek safe that is not answered in the FAQ section of this manual, we encourage you to email us: SUPPORT@VAULTEKSAFE.COM, Warranty VAULTEK IS COMMITTED TO PROVIDING PRODUCTS OF KIGH QUALITY AND VALUE AND MAKES EVERY EFFORT Vaultek guarantees your safe will be free of defects in materials or workmanship for a period of one year from the date of original purchase from an authorized dealer. This warranty does not cover abuse, misuse, use in any manner for which is not designed, neglected, modification, damage, inadvertently caused by the user, accidents, and/or tampering. lf your safe is determined to be defective, we wi'l at our discretion, have it repaired: at our expense, or will send you a new one at no cost to you. You will be required to return your existing unit as well as all included parts to Vaultek prior to replacement along with your proof of purchase, If it is determined your safe needs to be returned, a Vaultek agent will provide a Return Authorization Number. Please have the following information available when you contact us:

-Purchaser's name, mailing address, email address, and a phone number.

-Copy of receipt

-Authorized Dealer Name

-Detailed description of problem NEITHER SELLER NOR MANUFACTUI SHALL BE LIABL R ANY INJURY, LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR THE INABILITY TO USE THE VAULTEK SAFE. 27 Vaultek The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction FCC statements:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. 37 North Orange Ave. Sujte 800B Orlando, FL 32801