FCC ID: 2ABBNLE5LIT WEARABLE VIDEO CAMERA

FCC rev2 FCC CLASS B NOTICE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. 2. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Important: Changes or modifications to this product not authorized by VIEVU could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority to operate the product. This product has demonstrated EMC compliance under conditions that include the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions, and other electronic devices. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment for body-worn configuration in direct contact to the phantom. This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching FCC ID: 2ABBNLE5LIT LIMITED WARRANTY Product Warranty. Company warrants to purchaser that the Products purchased here under shall be free from defects in materials and workmanship and shall conform in all material respect to the specifications for a period of ninety (90) days from the date of delivery thereof, provided the Product in question has been stored and used in accordance with ordinary industry practices and conditions. The use of non-Company branded or approved accessories or replacement parts may result in damage not covered by warranty. Company does not warrant that the operation of the products will be uninterrupted or error free. In the event that a Product does not comply with Remedies. the product warranty set out above and such non-conforming Product is returned to Company within the warranty period by Purchaser freight prepaid, Company will repair or replace such non-conforming Product at no additional charge to Purchaser; the repaired or replaced Product will be returned to Purchaser, freight prepaid. Disclaimer of Warranties. The foregoing express warranties are limited to company and are not transferable and are in lieu of any other warranty by Company with respect to Products furnished hereunder. Company grants no other warranty, either express or implied, including without limitation, warranties or merchantability or fitness for a particular purpose. Limitation of Liability. Company shall in no event be liable for any indirect, incidental, special or consequential damages arising out of or relating to the sale or use of its products, whether or not Company has advance notice of the possibility of such damages. If company breaches any provision of this agreement, purchasers sole and exclusive maximum liability, whether based in contract, tort or otherwise, shall not in any event exceed the contract price for the particular products. Video Recovery Disclaimer: Purchaser is responsible for maintaining all evidence and videos taken with Company products. Purchaser should download all videos from Company products before returning to Company for repair or replacement. Purchaser shall indemnify Company for any evidence or videos that cannot be recovered from products. Caution: Risk of explosion or fire if battery is disassembled, punctured, cut, crushed, short-circuited, incinerated, or exposed to water, fire, or high temperatures. Properly dispose of used batteries in accordance with local regulations.

LE5 LITE BODY WORN CAMERA FIRST TIME SOFTWARE SETUP The LE5 Lite is an easy to operate wearable video camera designed specically for law enforcement and security professionals. 1. SELECT YOUR SOFTWARE Go to www.vievu.com/LE5litesetup and complete the sign-up process. After sign-up is complete, you will receive a welcome email with additional information. 2. INSTALL SOFTWARE ON COMPUTER The welcome email will contain a link to the software to install. Contact VIEVU at 888-285-4548 if you need assistance. 3. ASSIGN CAMERA IN SOFTWARE All cameras must be assigned before use. NOTE: Failure to assign the camera will prevent downloading videos. Using the supplied cable, connect the 2 large USB connectors to the computer. Connect the small connector to the bottom of the camera. Click the Assign Camera button in the software. For complete steps, consult the User Guides found in the welcome email. Detailed Specications USING THE CAMERA 1080 (FHD), 720 (HD) or 848x480 (SD) Video Resolution 30 Frames Per Second Recording Speed MPEG-4, H.264 Codec, AVI container Recording Format MOUNTING OPTIONS 95 degrees (diagonal) Lens Field of View Up to 6 hours at SD Resolution*

Recording Life The camera includes one universal attachment clip and one cable. 32 GB (non-removable) Storage Capacity The clip can rotate 360 degrees. The clip locks every 90 degrees, adjust the 28 hours at SD Resolution*

Video Storage position by twisting the clip. If the clip becomes loose, you may need to Weight (no clip) 2.7 oz tighten the locking screw using a Philips screwdriver. 2.52 x 2.2 x .95 Dimensions (no clip) Input DC 5V

-4F - 122F Temperature

* Environmental conditions may increase or decrease specication LED LIGHTS WEARING THE CAMERA STATUS LIGHT The camera must be worn with the LED lights facing up. The ideal position Camera is turning On. Fast Blink Blue:

to attach the camera is level with the sternum but it will vary depending Camera is in smartphone mode. Camera will Solid Red:

on the user. communicate with a smartphone. HINT: Use the smartphone app to conrm placement on your body. Camera is recording video and audio. Slow Blink Green:

Camera is low on battery power or memory is Fast Blink Yellow:

almost full. Camera is recording video and audio. Solid Yellow:

Camera is not recording. Battery is out of power or memory is full. Camera is installing rmware. Do not turn the Slow Blink White:

camera O or disconnect it from power or the camera rmware update may fail and cause the camera to become unresponsive. Camera is connected and in queue to download. Solid Blue:

Slow Blink Blue:

Camera is downloading video. CHARGING LIGHT Solid Red:

Solid Green:

RECORDING VIDEO NEED HELP?

Phone: 888-285-4548 (24/7/365) Email: support@vievu.com START RECORDING 1. Slide the record switch down. 2. The camera will turn on. The Rev2 STOP RECORDING 1. Slide the record switch up. 2. The camera will turn o. Battery is charging. Battery is fully charged. status light will blink green while recording. VIEVU.. 645 Elliott Ave W Ste 370 Seattle WA 98119. CONNECT TO SMARTPHONE The LE5 Lite is designed to turn o between recordings. In order to interact with the camera using a smartphone, the camera needs to be switched into smartphone mode. ACTIVATE SMARTPHONE MODE Press and hold the smartphone button on the side of the camera for 3 seconds. The status light will blink blue while activating and change to solid red when complete. You may now connect to the camera using a smartphone. DEACTIVATE SMARTPHONE MODE Press and hold the smartphone button on the side of the camera for 3 seconds. Smartphone mode will turn o. The status light will turn o. NOTE: While in smartphone mode, you can switch to recording video by sliding the record switch down. NOTE: Deactivate smartphone mode as soon as possible for maximum battery life. DOWNLOADING VIDEO DOWNLOAD WITH CABLE 1. Using the supplied cable, connect the 2 large USB connectors to the computer. Connect the small connector to the bottom of the camera. LE5 LITE INSTRUCTIONS Guide found at www.vievu.com/support for complete steps. 2. Login to the VIEVU software and click Download. Consult the User MULTIDOCK DOWNLOAD Insert the camera into an available port on the MultiDock. The status light will turn blue when the camera is in queue to download. The light will change to blinking blue when video les are being downloaded. The light will turn o when the download process is complete. LE5 LITE BODY WORN CAMERA FIRST TIME SOFTWARE SETUP The LE5 Lite is an easy to operate wearable video camera designed specically for law enforcement and security professionals. 1. SELECT YOUR SOFTWARE Go to www.vievu.com/LE5litesetup and complete the sign-up process. After sign-up is complete, you will receive a welcome email with additional information. 2. INSTALL SOFTWARE ON COMPUTER The welcome email will contain a link to the software to install. Contact VIEVU at 888-285-4548 if you need assistance. 3. ASSIGN CAMERA IN SOFTWARE All cameras must be assigned before use. NOTE: Failure to assign the camera will prevent downloading videos. Using the supplied cable, connect the 2 large USB connectors to the computer. Connect the small connector to the bottom of the camera. Click the Assign Camera button in the software. For complete steps, consult the User Guides found in the welcome email. Detailed Specications USING THE CAMERA 1080 (FHD), 720 (HD) or 848x480 (SD) Video Resolution 30 Frames Per Second Recording Speed MPEG-4, H.264 Codec, AVI container Recording Format MOUNTING OPTIONS 95 degrees (diagonal) Lens Field of View Up to 6 hours at SD Resolution*

Recording Life The camera includes one universal attachment clip and one cable. 32 GB (non-removable) Storage Capacity The clip can rotate 360 degrees. The clip locks every 90 degrees, adjust the 28 hours at SD Resolution*

Video Storage position by twisting the clip. If the clip becomes loose, you may need to Weight (no clip) 2.7 oz Philips screwdriver. tighten the locking screw using a 2.52 x 2.2 x .95 Dimensions (no clip) To maintain compliance with FCC RF exposure guidelines for body worn Input DC 5V operation, do not use accessories contain metallic components.

-4F - 122F Temperature

* Environmental conditions may increase or decrease specication LED LIGHTS WEARING THE CAMERA STATUS LIGHT The camera must be worn with the LED lights facing up. The ideal position Camera is turning On. Fast Blink Blue:

to attach the camera is level with the sternum but it will vary depending Camera is in smartphone mode. Camera will Solid Red:

on the user. communicate with a smartphone. HINT: Use the smartphone app to conrm placement on your body. Camera is recording video and audio. Slow Blink Green:

Camera is low on battery power or memory is Fast Blink Yellow:

almost full. Camera is recording video and audio. Solid Yellow:

Camera is not recording. Battery is out of power or memory is full. Camera is installing rmware. Do not turn the Slow Blink White:

camera O or disconnect it from power or the camera rmware update may fail and cause the camera to become unresponsive. Camera is connected and in queue to download. Solid Blue:

Slow Blink Blue:

Camera is downloading video. CHARGING LIGHT Solid Red:

Solid Green:

RECORDING VIDEO NEED HELP?

Phone: 888-285-4548 (24/7/365) Email: support@vievu.com START RECORDING 1. Slide the record switch down. 2. The camera will turn on. The Rev2 STOP RECORDING 1. Slide the record switch up. 2. The camera will turn o. Battery is charging. Battery is fully charged. status light will blink green while recording. VIEVU.. 645 Elliott Ave W Ste 370 Seattle WA 98119. CONNECT TO SMARTPHONE The LE5 Lite is designed to turn o between recordings. In order to interact with the camera using a smartphone, the camera needs to be switched into smartphone mode. ACTIVATE SMARTPHONE MODE Press and hold the smartphone button on the side of the camera for 3 seconds. The status light will blink blue while activating and change to solid red when complete. You may now connect to the camera using a smartphone. DEACTIVATE SMARTPHONE MODE Press and hold the smartphone button on the side of the camera for 3 seconds. Smartphone mode will turn o. The status light will turn o. NOTE: While in smartphone mode, you can switch to recording video by sliding the record switch down. NOTE: Deactivate smartphone mode as soon as possible for maximum battery life. DOWNLOADING VIDEO DOWNLOAD WITH CABLE 1. Using the supplied cable, connect the 2 large USB connectors to the computer. Connect the small connector to the bottom of the camera. LE5 LITE INSTRUCTIONS Guide found at www.vievu.com/support for complete steps. 2. Login to the VIEVU software and click Download. Consult the User MULTIDOCK DOWNLOAD Insert the camera into an available port on the MultiDock. The status light will turn blue when the camera is in queue to download. The light will change to blinking blue when video les are being downloaded. The light will turn o when the download process is complete.