Federal Communications Commission Statement This equipment has been followed with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures:
- Reorient or relocate the receiving antenna,
-
- Connect the equipment into and outlet on a circuit different from that to which the Increase the separation between the equipment and receiver, receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Limited Warranty Vision Guarantees that every wireless repeater is free from physical defects in material and workmanship under normal usage for one year from the date of purchase. If the product proves defective during this one-year warrany period, Vision will replace it free of charge. Vision does not issue any refunds. This warnnty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent usage; (2) units which have been repaired, taken apart, or modified by an unauthorized personnel; (3) units not used in accordance with instruction; (4) damanges exceeding the cost of the produt; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. For information on addional devices, plesae visit us at www.visionsecurity.com.tw ZR2102 V0 1021114 6B1Z-12001 Installation & Operation Manual ZR1202IN ZR1202EU ZR1202RU ZR1202US ZR1202IS ZR1202JP ZR1202BR Z-Wave Repeater Note: Suitable adapter specification:
-Micro USB Power Input
-Operating Voltage: 5V/DC
-Current Consumption: 500m Installation Notice: If you are installing the entire Z-Wave system for the first time, please refer to the installation guide of Z-Wave Interface Controller before installing ZR 1202 Repeater Module. 1. Fix the repeater under the vertical way as high as possible then insert the suitable Micro USB Power Adaptor to the ZR1202 then it will go to the Learning Mode automatically. (The LED will start flash which means the repeater has not been Include yet.) 2. For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode and following its instruction to add the ZR1202 to your controller. To get in the inclusion mode, the distance between module and controller is suggested to be in one meter. Press the program switch on the ZR1202 once. The LED should stop flashing, if not, please try again. For Exclusion from (removing from) a network: Put the Z-Wave Interface Controller into exclusion mode, and following its instruction to delete the ZR1202 from your controller. Press the program switch on the ZR1202 once to be excluded. Note: LED setting light will flash continuously in Exclusion condition. 3. Use Power Level Set command for setting the strength of RF during one Introduction Thanks for choosing the Visions repeater of the home automation device. This module is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave enabled network. Every main powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate RF dead-sports Z-Wave enabled devices displaying the Z-Wave logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturers Z-Wave enabled networks. This device take existing Z-WAVE signal, repeat and send it to a longer range where it is too far away for the controller (supporting FLiRS devices). Product Description and Specification
*** For indoor use only ***
Micro USB Power Input
(2)
(1) Release the bracket:
(1) Press
(2) Slide down to release the bracket Specification:
Protocol: Z-Wave (ZM4101) Frequency Range:
865.22MHz (ZR1202IN) 868.42MHz (ZR1202EU) 869.00MHz (ZR1202RU) 908.42MHz (ZR1202US) 916.00MHz (ZR1202IS) 920-928MHz(ZR1202JP) 921.42MHz (ZR1202BR) Operating Range: Up to 200 meters Operating Temp.: -15C~ 60C (5F ~140F) Operating Voltage: 5V/DC Current Consumption: 300mA (50mA) Z-Wave Command Class:
Program Switch period. 4. Use Power Level Test Node Set command to test the direct signal for fixed Package Content:
1pc 1pc 1pc 1pc ZR1202 Repeater module ZR1202 Repeater Bracket Adapter (Optional) Installation & Operation Manual node. 5. Support Repeaters for routing (FLiRS included) 6. Support Explorer Frame function 7. Press Program Switch for 5 seconds, the ZR1202 will reset back to factory default. The ZR1202 operating range will be up to 200 meters under the correct installation!!
COMMAND_CLASS_BASIC COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_VERSION
-1 - -2 -