FCC ID: NT8-BRFMS Battery Radiofrequency Module

BRFMS Model Name:

Battery Radiofrequency Module Type of product:

Visteon Brand Name:

Manufacturer:

Visteon Corporation Manufacturer Address: One Village center drive, Van Buren Township 48111-5711 Michigan United States of America BRFM features:

The BRFM is an electronic module intended to aggregate data from up to 24 CMU units and module temperatures from the High Voltage battery bus in addition to pack voltage and current data collected form the Battery Disconnect Signal Board (BDSB) and from multiple Cell Monitoring Units (CMUs) to communicate them to the Vehicle Integration Control Module (VICM3). All cell voltages, module temperatures, pack voltage and current are reported directly to the VICM3 on a regular periodic basis. BRFM Single variant has a single wireless RFIC (Pinnacle) and one antenna. The BRFM implements a Pinnacle IC (ADRF8850), this is an IC that provides wireless communication between the Battery Cell Monitoring chip and the Battery Management System Controller. The BRFM includes a voltage supervisor/windowed watchdog (TPS3850) counter which generates a wake up signal to the VICM3 when any of the battery cells reports a critical condition when the VICM3 is sleeping. The BRFM has two redundant sets of sensors that monitor the battery pack for excessive temperature, pressure, or hydrogen concentration that indicate a battery cell thermal runaway or thermal propagation. System interaction:

Module-to-Vehicle Electrical Interface Analog Input Analog Output Digital (discrete state) Output Communication Bus RF Link(s) VICM3 provides power to BRFM module. Power nominal value is 5.4V Minimum voltage expected is 5.2V and maximum is 5.6V. BDSB Power Output is provided or enabled by BRFM module depending on variant. BDSB Power is provided by Single BRFM variant. BDSB Power nominal value is 5V. Minimum voltage expected is 4.2V and maximum is 5.5V BDSB Power Output is provided or enabled by BRFM module depending on variant. BDSB Power is enabled by sending commands through the Dual BRFM variant. BDSB Power nominal value is 5V. Minimum voltage expected is 4.2V and maximum is 5.5V isoSPI communication serves as interface between BRFM and VICM3, as well as BRFM and BDSB. isoSPI lines shall be monitored to ensure proper performance. Amplitude and timing measurements should be captured. 1Mbps nominal is expected. ISM Band (2.4GHz to 2.5GHz) used to communicate with CMU modules. Rx sensitivity shall be around 50% of PER, where each measurement shall vary by no more than +/- 2.0dB from the golden sample. Tx output power shall vary by no more than +/-2.5dB from the golden sample. Radio frequency reference shall be within 20PPM from desired frequency

(2.44GHz, channel 7). Module-to-Vehicle Non-Electrical Interface Pressure Sensors -> Values shall be between 50kPa and 150kPa 1% (0 150C) and 2% (-40C 0C) Hydrogen Sensors -> Values shall be between 0PPM and 65,000PPM 100PPM (5% of accuracy) Temperature Sensors -> Detection range shall be between -40C and 150C 1% of measured value Internal Interface Note: For these internal I/O, monitoring shall only occur via communication bus data or via indirect methods. Direct monitoring using attachments leads to external monitoring devices shall not be included. Switching Clock

SPI communication shall be 1Mbps nominal. Used to communicate between RF manager to Sensors ASIC and RF Manager to isoSPI Transceiver. Frequency Content Analog Output RF Manager IC XTAL frequency shall be 40MHz nominal. Pressure sensor frequency shall be 20kHz. Hydrogen sensor frequency shall be 24.5kHz. UART communication between RF Manager 1 and RF Manager 2 for Dual BRFM variant. These shall be 1Mbps nominal. Digital (discrete state) Output 3.3V voltage output from U7/U9 shall be within the following range: +3.25V < VOUT < +3.35V Main power supply (U30001) shall have an output voltage of 3.3V with 5mV peak-to-peak ripple voltage Communication Bus Note: This section assumes that production software is not mandatory; the use of specialized software is acceptable. Note: Software diagnostic timers should be reset to minimum detection values, to facilitate assertion of potential diagnostic flags during the RF exposure time (maximum 2 seconds). Note: States/faults/issues shall be reported directly over the communication bus (i.e., Class 2, Controller Area Network (CAN), etc.) or indirectly if the communication bus is not available via the cycling of output(s) (e.g., PWM duty cycle change, telltale flash rate change, etc.) Note: Unless otherwise specified in the EMC Test Plan, in order to ensure a refreshed value, all information related to data monitoring (such as analog input voltages, operating states, etc.) shall be via parameter requests (e.g., Parameter ID (PID)) and not via scheduled, or periodic, broadcast messages. This ensures bi-directional communications during immunity testing. Harness Pinout, Capacities, and Use Name Description Connecto r ID /

Cavity #

Wire Gauge

(AWG) Used in Vehicle Twist w/

Cavity

Shield ed w/

Cavity

Termination

(R-L-C) etc. Applicable Bands Required for Module Operation External Antenna Band WiFi X1-1 X1-2 X1-3 X1-4 X1-5 X1-6 X1-7 X1-8 X1-9 X1-10 X1-11 X1-12 X1-13 BUF5V I NC NC VICM_ WU_SI G BUF5V O NC RTN_5 VO RTN_5 VI BRFM_ SPLY_ V_2 NC ISOSPI _PV2 5V Input Power from VICM NC NC Vehicle Integration Control Module Wake Up Signal 5V Output Power to BDSB NC Ground to BDSB Ground to VICM Battery Radio Frequency Module Supply Voltage 2 NC isoSPI Positive 2 to VICM ISOSPI _NV2 ISOSPI _PV1 isoSPI Negative 2 to VICM isoSPI Positive 1 to VICM Connect to 5V BDSB or simulator 100 ohm cross positive and negative 100 ohm cross positive and negative 16 n/a n/a 16 16 n/a 16 16 16 n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a 20 n/a n/a Yes n/a n/a Yes Yes n/a Yes Yes Yes n/a Yes n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a External Antenna Band YYYY n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a 20 n/a n/a Yes n/a n/a X1-14 X1-15 X1-16 X1-17 X1-18 X1-19 X1-20 ISOSPI _NV1 ISOSPI _PB1 isoSPI Negative 1 to VICM isoSPI Positive 1 to BDSB 1 ISOSPI _NB1 ISOSPI _PB2 isoSPI Negative 1 to BDSB 1 isoSPI Positive 2 to BDSB 2 ISOSPI _NB2 NC BRFM_ RTN_2 IsoSPI Negative 2 to BDSB 2 NC Battery Radio Frequency Module Return 2 100 ohm cross positive and negative 100 ohm cross positive and negative BDSB or simulation 20 n/a n/a Yes n/a n/a 20 n/a n/a Yes n/a n/a n/a 16 n/a n/a n/a n/a n/a Yes n/a n/a n/a n/a The following information shall also be included in the case of radio equipment intentionally emitting radio waves:

a. Frequency band : 2.4 2.5 GHz b. Maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates. Max output power = 10dBM

(U.S.A. and Canada) FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) The device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. RF exposure safety This device complies with the FCC RF exposure limits and has been evaluated in compliance with portable exposure conditions. The equipment must be installed and operated and was evaluated with minimum distance of 11 cm of the human body. This distance or greater is maintained by vehicle design and ensures compliance by normal use of the vehicle. ISED CANADA This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) The device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et,

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF exposure safety This device complies with ISED RF exposure limits and has been evaluated in compliance with portable exposure conditions. The equipment must be installed and operated and was evaluated with minimum distance of 11 cm of the human body. This distance or greater is maintained by vehicle design and ensures compliance by normal use of the vehicle. CAN ICES-003 Les changements ou modifications non expressment approuvs par la partie responsable de la conformit peuvent annuler le droit de l'utilisateur utiliser l'quipement. Scurit d'exposition aux RF Cet appareil est conforme aux limites d'exposition RF d'ISDE et a t valu conformment aux conditions d'exposition portable. L'quipement doit tre install et utilis une distance minimale de 11 cm du corps humain. CAN NMB-003 Cet appareil numrique de classe B est conforme la norme canadienne NMB-003.

BRFMS Model Name:

Battery Radiofrequency Module Type of product:

Visteon Brand Name:

Manufacturer:

Visteon Corporation Manufacturer Address: One Village center drive, Van Buren Township 48111-5711 Michigan United States of America BRFMS features:

The BRFMS is an electronic module intended to aggregate data from up to 12 CMU units and module temperatures from the High Voltage battery bus in addition to pack voltage and current data collected form the Battery Disconnect Signal Board (BDSB) and from multiple Cell Monitoring Units (CMUs) to communicate them to the Vehicle Integration Control Module (VICM3). All cell voltages, module temperatures, pack voltage and current are reported directly to the VICM3 on a regular periodic basis. BRFMS Single variant has a single wireless RFIC (Pinnacle) and one antenna. The BRFMS implements a Pinnacle IC (ADRF8850), this is an IC that provides wireless communication between the Battery Cell Monitoring chip and the Battery Management System Controller. The BRFMS includes a voltage supervisor/windowed watchdog (TPS3850) counter which generates a wake up signal to the VICM3 when any of the battery cells reports a critical condition when the VICM3 is sleeping. The BRFMS has two redundant sets of sensors that monitor the battery pack for excessive temperature, pressure, or hydrogen concentration that indicate a battery cell thermal runaway or thermal propagation. System interaction:

Module-to-Vehicle Electrical Interface Analog Input Analog Output Digital (discrete state) Output Communication Bus RF Link(s) VICM3 provides power to BRFMS module. Power nominal value is 5.4V Minimum voltage expected is 5.2V and maximum is 5.6V. BDSB Power Output is provided or enabled by BRFMS module depending on variant. BDSB Power is provided by Single BRFMS variant. BDSB Power nominal value is 5V. Minimum voltage expected is 4.2V and maximum is 5.5V BDSB Power Output is provided or enabled by BRFMS module depending on variant. BDSB Power is enabled by sending commands through the Dual BRFMS variant. BDSB Power nominal value is 5V. Minimum voltage expected is 4.2V and maximum is 5.5V isoSPI communication serves as interface between BRFMS and VICM3, as well as BRFMS and BDSB. isoSPI lines shall be monitored to ensure proper performance. Amplitude and timing measurements should be captured. 1Mbps nominal is expected. ISM Band (2.405 GHz to 2.480 GHz) used to communicate with CMU modules. Rx sensitivity shall be around 50% of PER, where each measurement shall vary by no more than +/- 2.0dB from the golden sample. Tx output power shall vary by no more than +/-2.5dB from the golden sample. Radio frequency reference shall be within 20PPM from desired frequency (2.44GHz, channel 7). Module-to-Vehicle Non-Electrical Interface Pressure Sensors -> Values shall be between 50kPa and 150kPa 1% (0 150C) and 2% (-40C 0C) Hydrogen Sensors -> Values shall be between 0PPM and 65,000PPM 100PPM (5% of accuracy) Temperature Sensors -> Detection range shall be between -40C and 150C 1% of measured value Internal Interface Note: For these internal I/O, monitoring shall only occur via communication bus data or via indirect methods. Direct monitoring using attachments leads to external monitoring devices shall not be included. Switching Clock

SPI communication shall be 1Mbps nominal. Used to communicate between RF manager to Sensors ASIC and RF Manager to isoSPI Transceiver. Frequency Content Analog Output RF Manager IC XTAL frequency shall be 40MHz nominal. Pressure sensor frequency shall be 20kHz. Hydrogen sensor frequency shall be 24.5kHz. UART communication between RF Manager 1 and RF Manager 2 for Dual BRFMS variant. These shall be 1Mbps nominal. Digital (discrete state) Output 3.3V voltage output from U7/U9 shall be within the following range: +3.25V < VOUT < +3.35V Main power supply (U30001) shall have an output voltage of 3.3V with 5mV peak-to-peak ripple voltage Communication Bus Note: This section assumes that production software is not mandatory; the use of specialized software is acceptable. Note: Software diagnostic timers should be reset to minimum detection values, to facilitate assertion of potential diagnostic flags during the RF exposure time (maximum 2 seconds). Note: States/faults/issues shall be reported directly over the communication bus (i.e., Class 2, Controller Area Network (CAN), etc.) or indirectly if the communication bus is not available via the cycling of output(s) (e.g., PWM duty cycle change, telltale flash rate change, etc.) Note: Unless otherwise specified in the EMC Test Plan, in order to ensure a refreshed value, all information related to data monitoring (such as analog input voltages, operating states, etc.) shall be via parameter requests (e.g., Parameter ID (PID)) and not via scheduled, or periodic, broadcast messages. This ensures bi-directional communications during immunity testing. Note: The BRFMS is powered by a power supply that meets the requirements of ES1 and PS1 (P<15W) in accordance with the IEC 62368-1 standard. Harness Pinout, Capacities, and Use Name Description Connecto r ID /

Cavity #

Wire Gauge

(AWG) Used in Vehicle Twist w/

Cavity

Shield ed w/

Cavity

Termination

(R-L-C) etc. Applicable Bands Required for Module Operation External Antenna Band WiFi X1-1 X1-2 X1-3 X1-4 X1-5 X1-6 X1-7 X1-8 X1-9 X1-10 X1-11 X1-12 X1-13 BUF5V I NC NC VICM_ WU_SI G BUF5V O NC RTN_5 VO RTN_5 VI BRFM S_SPL Y_V_2 NC ISOSPI _PV2 5V Input Power from VICM NC NC Vehicle Integration Control Module Wake Up Signal 5V Output Power to BDSB NC Ground to BDSB Ground to VICM Battery Radio Frequency Module Supply Voltage 2 NC isoSPI Positive 2 to VICM ISOSPI _NV2 ISOSPI _PV1 isoSPI Negative 2 to VICM isoSPI Positive 1 to VICM Connect to 5V BDSB or simulator 100 ohm cross positive and negative 100 ohm cross 16 n/a n/a 16 16 n/a 16 16 16 n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a 20 n/a n/a Yes n/a n/a Yes Yes n/a Yes Yes Yes n/a Yes n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a 20 n/a n/a Yes n/a n/a External Antenna Band YYYY n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a X1-14 X1-15 X1-16 X1-17 X1-18 X1-19 X1-20 ISOSPI _NV1 ISOSPI _PB1 isoSPI Negative 1 to VICM isoSPI Positive 1 to BDSB 1 ISOSPI _NB1 ISOSPI _PB2 isoSPI Negative 1 to BDSB 1 isoSPI Positive 2 to BDSB 2 ISOSPI _NB2 NC BRFM S_RTN _2 IsoSPI Negative 2 to BDSB 2 NC Battery Radio Frequency Module Return 2 positive and negative 100 ohm cross positive and negative 100 ohm cross positive and negative BDSB or simulation 20 n/a n/a Yes n/a n/a 20 n/a n/a Yes n/a n/a n/a 16 n/a n/a n/a n/a n/a Yes n/a n/a n/a n/a The following information shall also be included in the case of radio equipment intentionally emitting radio waves:

a) Frequency band : 2.405 2.480 GHz b) Maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates. Max output power = 10dBM

(U.S.A. and Canada) FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) The device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF exposure safety This device complies with the FCC RF exposure limits and has been evaluated in compliance with portable exposure conditions. The equipment must be installed and operated and was evaluated with minimum distance of 11 cm of the human body. This distance or greater is maintained by vehicle design and ensures compliance by normal use of the vehicle. ISED CANADA This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) The device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et,

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF exposure safety This device complies with ISED RF exposure limits and has been evaluated in compliance with portable exposure conditions. The equipment must be installed and operated and was evaluated with minimum distance of 11 cm of the human body. This distance or greater is maintained by vehicle design and ensures compliance by normal use of the vehicle. CAN ICES-003 Les changements ou modifications non expressment approuvs par la partie responsable de la conformit peuvent annuler le droit de l'utilisateur utiliser l'quipement. Scurit d'exposition aux RF Cet appareil est conforme aux limites d'exposition RF d'ISDE et a t valu conformment aux conditions d'exposition portable. L'quipement doit tre install et utilis une distance minimale de 11 cm du corps humain. Cette distance ou plus est maintenue par la conception du vhicule et garantit la conformit par une utilisation normale du vhicule. CAN NMB-003 Cet appareil numrique de classe B est conforme la norme canadienne NMB-003. Customer Information Declaration of Conformity _____________________________________________________________________________________ CE MARK:

Simplified EU DoC:

Hereby, Visteon Corporation declares that the radio equipment type BRFMS is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.visteondocs.com/

[Bulgarian]

esky

[Czech]

Dansk

[Danish]

Deutsch

[German]

Eesti

[Estonian]

English Espaol

[Spanish]

[Greek]

Franais

[French]

Visteon Corporation , BRFMS 2014/53/EC. Visteon Corporation tmto prohlauje, e tento BRFMS je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 2014/53/EU. Undertegnede Visteon Corporation erklrer herved, at flgende udstyr BRFMS overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/EU. Hiermit erklrt Visteon Corporation, dass sich das Gert BRFMS in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 2014/53/EU befindet. Kesolevaga kinnitab Visteon Corporation seadme BRFMS vastavust direktiivi 2014/53/EL phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, Visteon Corporation, declares that this BRFMS is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Por medio de la presente Visteon Corporation declara que el BRFMS cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/UE. Visteon Corporation BRFMS 2014/53/. Par la prsente Visteon Corporation dclare que l'appareil BRFMS est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/UE. Italiano

[Italian]

Latviski

[Latvian]

Lietuvi

[Lithuanian]

Nederlands

[Dutch]

Malti

[Maltese]

Magyar

[Hungarian]

Polski

[Polish]

Portugus

[Portuguese]

Slovensko

[Slovenian]

Slovensky

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

slenska

[Icelandic]

Norsk

[Norwegian]

Crnogorski jezik,

[Montenegrin]

Con la presente Visteon Corporation dichiara che questo BRFMS conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/UE. Ar o Visteon Corporation deklar, ka BRFMS atbilst Direktvas 2014/53/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo Visteon Corporation deklaruoja, kad is BRFMS atitinka esminius reikalavimus ir kitas 2014/53/EB Direktyvos nuostatas. Hierbij verklaart Visteon Corporation dat het toestel BRFMS in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 2014/53/EG. Hawnhekk, Visteon Corporation, jiddikjara li dan BRFMS jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 2014/53/UE. Alulrott, Visteon Corporation nyilatkozom, hogy a BRFMS megfelel a vonatkoz alapvet kvetelmnyeknek s az 2014/53/EU irnyelv egyb elrsainak. Niniejszym Visteon Corporation owiadcza, e BRFMS jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 2014/53/UE. Visteon Corporation declara que este BRFMS est conforme com os requisitos essenciais e outras disposies da Directiva 2014/53/UE. Visteon Corporation izjavlja, da je ta BRFMS v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 2014/53/ES. Visteon Corporation tmto vyhlasuje, e BRFMS spa zkladn poiadavky a vetky prslun ustanovenia Smernice 2014/53/E. Visteon Corporation vakuuttaa tten ett BRFMS tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar Visteon Corporation att denna BRFMS str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/EU. Hr me lsir Visteon Corporation yfir v a BRFMS er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 2014/53/EU. Visteon Corporation erklrer herved at utstyret BRFMS er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EF. Ovim, Visteon Corporation, izjavljuje da ovaj BRFMS je usklaen sa bitnim zahtjevima i drugim relevantnim odredbama Direktive 2014/53/UE. Romn

[Romanian]

Trkiye

[Turkey]

Hrvatska

[Croatian]

Prin prezenta, Visteon Corporation, declar c acest BRFMS respect cerinele eseniale i alte dispoziii relevante din Directiva 2014/53 / UE. Visteon Corporation, ibu BRFMS 'n 2014/53 / EU Direktifinin esas artlar ve dier ilgili hkmlerine uygun olduunu beyan eder. Ovime Visteon Corporation izjavljuje da je ovaj BRFMS u skladu s osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 2014/53 / EU. United Arab Emirates Kingdom of Saudi Arabia Oman Mexico Homologation by IFTXXXXXXXXX-XXXX Certification By: NYCE

'La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada'. a) Lea el Manual antes de operar o usar el Equipo. b) Informacin de importador:

Nombre: General Motors de Mxico, S. de R. L. de C. V. Direccin/Address: Av. Ejrcito Nacional 843-B. Colonia Granada, Miguel Hidalgo. CP 11520 Ciudad de Mxico, Mxico. Contacto: Fernando Camacho Jimnez Correo: fernando.camacho@gm.com Telfono: (52-722) 235 8487 c) Marca: Visteon Corporation / Nombre del Modelo: BRFMS d) El BRFMS es instalado dentro del Battery Pack, por lo tanto, el usuario final no tiene interaccin directa con el mdulo BRFMS. e) Especificaciones Elctricas:

Tensin de alimentacin: 5,4V (Vcc) Corriente de alimentacin: 450 mA Frecuencia: 2.4 GHz Potencia: 2.5 W China This device contains SRRC type approval radio transmitter module with code as: CMIIT ID: XXXXYZNNNN'.

(): CMIIT ID:XXXXYYZZZZ,... Israel XX-XXXXX

"Wireless approval signed by the Ministry of Communication no. #ID Certificate"

Japan

. Kazakhstan Safety using requirements. (GM will need to provide or place this information on final User Manual in Russian and Kazakhstan language). Installing, storing, shipping, sailing and utilization requirements. (GM will need to provide or place this information on final User Manual in Kazakhstan language). South Korea

: TBD

: Visteon Corporation

/ : BRFMS

/: Visteon Corporation /USA United Kingdom a. Frequency band : 2.405 2.480 GHz b. Maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates. Max output power = 10dBM

Traceability Data Identifier L = Line/Machine (assigned by supplier)

[( S$ = Shift (assigned by supplier)

[)>*,06, 0000000000000X,?12345678, 1 2V987654321.TLSYYDDDTRACEDATA.0, vPPS Identifier | |

Compt .d VPPS with Location Code ~

GM Part Number Data Identifier GM Part Number B= 12345678 LSYYDDDTRACEDATA Supplier DUNS Data Identifier Supplier DUNS (Numeric) YY = Manufactured/Assembled Year DDD = Julian Day Manufactured/Assembled Supplier Assigned and Managed Serial Number

(9 alpha and/or numeric characters)

Traceability Data Identifier L = Line/Machine (assigned by supplier)

[( S$ = Shift (assigned by supplier)

[)>*,06, 0000000000000X,?12345678, 1 2V987654321.TLSYYDDDTRACEDATA.0, vPPS Identifier | |

Compt .d VPPS with Location Code ~

GM Part Number Data Identifier GM Part Number e= 12345678 LSYYDDDTRACEDATA Supplier DUNS Data Identifier Supplier DUNS (Numeric) YY = Manufactured/Assembled Year DDD = Julian Day Manufactured/Assembled Supplier Assigned and Managed Serial Number

(9 alpha and/or numeric characters)

Visteon Corporation One Village Center Drive Van Buren Township, MI, 48111 Date: February 10, 2022 DEKRA Testing and Certification, S.A.U. Parque Tecnolgico de Andaluca C/ Severo Ochoa 2 & 6 29590 Campanillas Mlaga, Espaa Ref: Confidentiality request for FCC ID: NT8-BRFMS To whom it may concern:

Pursuant to 0.457(d)(1)(ii) and 0.459 of the Commissions Rules (47 C.F.R.) and 552 (b)(4) of the Freedom of Information Act, Visteon Corporation hereby request requests that a part of the subject FCC application be held confidential to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose:

Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent Permanent Exhibit Block Diagrams External Photos Internal Photos Operation Description Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Permanent Confidentiality:

The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to us and provide unjustified benefits to our competitors. Short-Term Confidentiality:

We hereby request short-term confidentiality for the product stated above to avoid premature release of sensitive information prior to marketing or release of the product to the public. Release date of short term confidentiality is:

45 days from grant date marked 90 days from grant date marked 135 days from grant date marked 180 days from grant date marked Specific date:

Sincerely, __________________________ Terry SanSouci By:

Environmental Validation Engineer Title:

Visteon Corporation Company:

Telephone:

(734) 710-7137 e-mail: tsansouc@visteon.com FCB017_03 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless

Visteon Corporation One Village Center Drive Van Buren Township, MI, 48111 Date: August 11, 2022 DEKRA Testing and Certification, S.A.U. Parque Tecnolgico de Andaluca C/ Severo Ochoa 2 & 6 29590 Campanillas Mlaga, Espaa Ref: Confidentiality request for FCC ID: NT8-BRFMS To whom it may concern:

Pursuant to 0.457(d)(1)(ii) and 0.459 of the Commissions Rules (47 C.F.R.) and 552 (b)(4) of the Freedom of Information Act, Visteon Corporation hereby request requests that a part of the subject FCC application be held confidential to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose:

Type of Confidentiality Requested Exhibit Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent Permanent Permanent Block Diagrams External Photos Internal Photos Operation Description Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual SDR software and security information Permanent Confidentiality:

The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to us and provide unjustified benefits to our competitors. Short-Term Confidentiality:

We hereby request short-term confidentiality for the product stated above to avoid premature release of sensitive information prior to marketing or release of the product to the public. Release date of short term confidentiality is:

45 days from grant date marked 90 days from grant date marked 135 days from grant date marked 180 days from grant date marked Specific date:

We are also aware that we are responsible to notify DEKRA in the event information regarding the product or the product is made available to the public. DEKRA will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, Terry SanSouci Environmental Validation Engineer __________________________ By:

Title:

Company: Visteon Corporation Telephone: (734) 710-7137 e-mail: tsansouc@visteon.com FCB012_04 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless

Visteon Corporation One Village Center Drive Van Buren Township, MI, 48111 Class II Permissive Change Request Letter Date: August 30, 2022 SUBJECT: FCC Application for (FCC ID: NT8-BRFMS) To Whom It May Concern:

We, Name:

Address:

City:

Country:

Visteon Corporation One village center drive Van Buren Township, MI, 48111 USA Are submitting an application for a class II permissive change to the FCC Granted ID NT8-BRFMS. Description: Battery Radiofrequency Module Single (BRFMS). The transmitter module itself has not changed. Here are the changes:

- At a vehicle level,12 SLAs configuration working with a BRFMS inside a sealed battery pack. BRFMS operates in the frequency range 2.405 GHz - 2.480 GHz (ISM band) by using Wireless battery management technology. Housing geometry changes, resistor change to increase threshold response, test point moved. RF circuits remains as the initial certification. Test reports will be available for EMC and RF for device according to "FCC CFR 47,Part 15, Subpart B, FCC Part 15.247 and FCC Part 15.209. Sincerely,

Terry SanSouci By:

Title:

Environmental Validation Engineer Company: Visteon Corporation Telephone: (734) 710-7137 e-mail:

tsansouc@visteon.com

Visteon Corporation One Village Center Drive Van Buren Township, MI, 48111 Declaration of Authorization Date: February 10, 2022 DEKRA Testing and Certification, S.A.U. Parque Tecnolgico de Andaluca C/ Severo Ochoa 2 & 6 29590 Campanillas Mlaga, Espaa Ref: Agent letter for FCC ID: NT8-BRFMS We, Visteon Corporation One Village Center Drive Van Buren Township, MI, 48111 USA Name:

Address:

City:

Country:

hereby authorize DEKRA Certification, Inc. 405 Glenn Drive, Suite 11&12 Sterling, VA. USA, 20164 Mr. Domingo Galvez, EMC&RF Lab Manager e-mail: domingo.galvez@dekra.com Phone: +1 (732) 207-8336 to act as our agent in the preparation of this application for equipment certification, including the signing of all documents relating to these matters. The present authorization considers the development of documents on behalf of the client, written under his own letterhead and related to the necessary information to be provided on his behalf to complete the certification process. We also hereby certify that neither we nor any party to this application are subject to a denial of U.S. Federal benefits, which include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862 because of conviction for possession or distribution of controlled substance. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by DEKRA Testing and Certification, S.A.U., still resides with us. This agreement expires one year from the current date. Sincerely,

By: Terry SanSouci Title: Environmental Validation Engineer Company: Visteon Corporation Telephone: (734) 710-7137 e-mail: tsansouc@visteon.com FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless