FCC ID: 2AVEACE-P21-7005 Monitor

Public View Monitor Manual for models:

CE-M8XXXXXXXXXX CE-M21XXXXXXXXXX CE-M32XXXXXXXXXX CE-M10XXXXXXXXXX CE-P21XXXXXXXXXX CE-P32XXXXXXXXXX CE-P10XXXXXXXXXX CE-M24XXXXXXXXXX CE-M43XXXXXXXXXX CE-P13XXXXXXXXXX CE-27XXXXXXXXXX CE-P43XXXXXXXXXX CE-M16XXXXXXXXXX CE-M27XXXXXXXXXX Disclaimer: Clinton Electronics Corporation makes no representations or warranties, either expressed or implied, with respect to the contents of this document. Clinton Electronics Corporation reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes. Check clintonelectronics.com for the most current model specifications. For additional technical support visit support.clintonelectronics.com E N G IMPORTANT SAFEGUARDS Federal Communications Commission Statement (FCC) This Class A device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense. The user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution To assure continued compliance, any changes or modifications not expressly approved by Clinton Electronics for compliance could void the users authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Warning: Operation of this equipment in a residential environment could cause radio interference. CAUTION:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. A shielded-type power cord is required in order meet FCC emission limits and also to prevent interference to the nearby radio and television reception, It is essential that only the supplied power cord be used. 2. Use only shielded cables to connect I/O devices to this equipment. 3. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. II IMPORTANT SAFEGUARDS G N E CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT DISASSEMBLE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICE TO QUALIFIED PERSONNEL. The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Installation should be made by a qualified service person and should conform to all local codes. Safety Warnings Read all of these instructions. Save these instructions for later use. Follow all warnings and instructions marked on the monitor. If provided with a 3-pin attachment plug on the power cord, (either from a supplied power cord or from external power supply) plug the cord into a grounded (earthed) 3-pin outlet. If you are unable to insert the plug into the outlet, contact a qualified electrician to replace the outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter or by breaking the grounding pin off. The grounding pin is an important safety feature. This monitor should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to use, consult the products specifications online or check with qualified service person. Do not overload wall outlets, power strips and/or extension cords as this can result in fire or electric shock. Do not use attachments not recommended by the monitor manufacturer as they may cause hazards. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that has the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards. The monitor shall be connected to ITE product with Limited Power Source(LPS) Output approved by Underwriters Laboratories (UL OR TUV) Do not attempt to service this monitor yourself since opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Upon completion of any service or repairs to this monitor, ask the service technician to perform routine safety checks to determine that the monitor is in safe operating condition. Intended Use This product is intended for professional and commercial use only as part of a video surveillance and monitoring system. III E N G IMPORTANT SAFEGUARDS Operating Precautions Do not use this monitor near water. For example near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.. Use only with a cart or stand recommended by the manufacturer or sold with monitor. Wall or shelf mounting should follow the manufacturers instructions, and should use a mounting kit approved by the manufacturer. Do not place this monitor on an unstable cart, stand, or table. The monitor may fall, causing serious injury to a child or adult, and serious damage to the appliance. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of the monitor and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the monitor on a bed, sofa, rug, or other similar surface. This monitor should never be placed near or over a radiator or heat register. This monitor should not be placed in built-in installation such as a bookcase unless proper ventilation is provided. Do not allow anything to rest on the power cord. Do not locate this monitor where the cord will be abused by persons working on it. Do not bend, crimp or otherwise damage the power cord. Never push objects of any kind into this monitor through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on or into the monitor. This equipment is not suitable for use in locations where children are likely to be present. This equipment is not intended for the display of television broadcast signals. Disconnect power before cleaning. Maintenance For added protection for this monitor, when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the monitor due to power-

line surges. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any cleaning solution or glass cleaner. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:

When the power cord or plug is damaged or frayed. If liquid has been spilled into the monitor. If the monitor has been exposed to rain or water. If the monitor does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the monitor to normal operation. If the monitor has been dropped or the cabinet has been damaged. When the monitor exhibits a distinct change in performance- this indicated a need for service. Warning Excessive usage may harm your vision. Take a 10-minute break for every 30 minutes of screen time. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day. Avoid displaying fixed patterns on the monitor for long periods of time to avoid screen burn/

image persistence (after image effects). Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:

If the power supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the monitor. If the monitor has been exposed to rain or water. If the monitor has been dropped or the cabinet damaged. If you notice any structural damage such as cracks or unnatural wobbling. If the monitor does not operate normally by following operating instructions. Environmental Conditions Indoor use only - unless specified Do not install where the ventilation is restricted or blocked Do not expose the monitor to excessive temperatures, humidity, or moisture (refer to product specification for more information) IV IMPORTANT SAFEGUARDS Explanation of Graphical Symbols:

Exclamation-Triangle This symbol alerts the user that important information concerning the operation and maintenance of this unit has been included. Therefore, the information should be read carefully in order to avoid any problems. Following international standards compliance are variously acquired by different model, please check the certification tag behind this monitor to confirm what standards are actual acquired. UL 62368-1:2025 CSA C22.2 No. 62368-1:25 IEC 62368-1:2018 IEC 62368-1:2022 EN 55032 EN55035 47 CFR FCC Part 15, Subpart B, Class A G N E V E S P PRECAUCIONES IMPORTANTES Declaracin de la Comisin Federal de Comunicaciones (FCC) Este dispositivo de Clase A cumple con la Parte 15 de las normas de la FCC. Su funcionamiento est sujeto a las dos condiciones siguientes:

1. Este dispositivo no puede causar interferencias perjudiciales. 2. Este dispositivo debe aceptar cualquier interferencia recibida, incluidas aquellas que puedan causar un funcionamiento no deseado. Nota: Este equipo ha sido probado y se ha comprobado que cumple con los lmites para un dispositivo digital de Clase A, de conformidad con la Parte 15 de las normas de la FCC. Estos lmites estn diseados para proporcionar una proteccin razonable contra interferencias perjudiciales cuando el equipo se utiliza en un entorno comercial. Este equipo genera, utiliza y puede emitir energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con el manual de instrucciones, puede causar interferencias perjudiciales a las comunicaciones por radio. El uso de este equipo en un entorno residencial probablemente cause interferencias perjudiciales, en cuyo caso el usuario deber corregirlas a su propio costo. Se recomienda al usuario intentar corregir la interferencia mediante una o ms de las siguientes medidas:

Reorientar o reubicar la antena receptora. Aumentar la separacin entre el equipo y el receptor. Conectar el equipo a una toma de corriente en un circuito diferente al del receptor. Consultar al distribuidor o a un tcnico de radio/televisin con experiencia. Advertencia FCC Para asegurar el cumplimiento continuo, cualquier cambio o modificacin no aprobada expresamente por Clinton Electronics puede anular la autoridad del usuario para operar este equipo. (Ejemplo: utilizar nicamente cables de interfaz blindados al conectar a computadoras o dispositivos perifricos). Declaracin de exposicin a radiacin FCC Este equipo cumple con los lmites de exposicin a radiacin RF de la FCC establecidos para un entorno no controlado. Debe instalarse y operarse con una distancia mnima de 20 cm entre el radiador y el cuerpo del usuario. Este transmisor no debe colocarse ni operar junto con otra antena o transmisor. Las antenas utilizadas deben instalarse de forma que mantengan una separacin de al menos 20 cm respecto a todas las personas y no deben colocarse junto con otras antenas o transmisores. CE Advertencia: el funcionamiento de este equipo en un entorno residencial puede causar interferencias de radio. PRECAUCIN:

RIESGO DE EXPLOSIN SI LA BATERA SE REEMPLAZA POR UN TIPO INCORRECTO. DESECHE LAS BATERAS USADAS SEGN LAS INSTRUCCIONES. 1. Se requiere un cable de alimentacin blindado para cumplir con los lmites de emisiones de la FCC y para evitar interferencias con la recepcin de radio y televisin cercana. Es esencial utilizar nicamente el cable de alimentacin suministrado. 2. Utilice nicamente cables blindados para conectar dispositivos de entrada/salida a este equipo. 3. Se le advierte que los cambios o modificaciones no aprobados expresamente por la parte responsable del cumplimiento pueden anular su autorizacin para operar el equipo. VI PRECAUCIONES IMPORTANTES P S E PRECAUCIN RIESGO DE DESCARGA ELCTRICA. NO ABRIR. PARA REDUCIR EL RIESGO DE DESCARGA ELCTRICA, NO DESMONTE EL EQUIPO. NO HAY PIEZAS EN EL INTERIOR QUE PUEDAN SER REPARADAS POR EL USUARIO. CONFE EL SERVICIO A PERSONAL CALIFICADO. El smbolo del rayo con una punta de flecha dentro de un tringulo equiltero tiene como objetivo alertar al usuario sobre la presencia de voltaje peligroso no aislado dentro del gabinete del producto, de magnitud suficiente como para constituir un riesgo de descarga elctrica para las personas. El signo de exclamacin dentro de un tringulo equiltero tiene como objetivo alertar al usuario sobre la presencia de instrucciones importantes de operacin y mantenimiento (servicio) en la documentacin que acompaa al aparato. La instalacin debe ser realizada por personal de servicio calificado y debe cumplir con todos los cdigos y normativas locales. Advertencias de seguridad Lea todas estas instrucciones. Conserve estas instrucciones para uso futuro. Siga todas las advertencias e instrucciones marcadas en el monitor. Si el cable de alimentacin incluye un enchufe de 3 pines (ya sea del cable suministrado o de una fuente de alimentacin externa), conctelo a una toma de corriente de 3 pines con conexin a tierra. Si no puede insertar el enchufe en la toma, contacte a un electricista calificado para reemplazarla. No desactive la conexin a tierra del cable de alimentacin, por ejemplo, utilizando un adaptador de 2 pines o rompiendo la clavija de tierra. La clavija de tierra es una caracterstica de seguridad importante. Este monitor debe utilizarse nicamente con el tipo de fuente de alimentacin indicado en la etiqueta de especificaciones. Si no est seguro del tipo de alimentacin a utilizar, consulte las especificaciones del producto en lnea o contacte a un tcnico de servicio calificado. No sobrecargue las tomas de corriente, regletas o extensiones elctricas, ya que esto puede provocar incendios o descargas elctricas. No utilice accesorios no recomendados por el fabricante del monitor, ya que pueden causar riesgos. Cuando se requieran piezas de repuesto, asegrese de que el tcnico de servicio utilice piezas especificadas por el fabricante y con las mismas caractersticas que las originales. Las sustituciones no autorizadas pueden provocar incendios, descargas elctricas u otros peligros. El monitor debe conectarse a un equipo ITE con fuente de alimentacin limitada (LPS) aprobada por Underwriters Laboratories (UL) o TV. No intente reparar este monitor usted mismo, ya que abrir o retirar las cubiertas puede exponerle a voltajes peligrosos u otros riesgos. Todas las reparaciones deben ser realizadas por personal tcnico calificado. Una vez finalizada cualquier reparacin o servicio, solicite al tcnico que realice revisiones de seguridad rutinarias para confirmar que el monitor se encuentra en condiciones seguras de funcionamiento. Uso previsto Este producto est destinado nicamente a uso profesional y comercial como parte de un sistema de videovigilancia y monitoreo. VII E S P PRECAUCIONES IMPORTANTES Precauciones de uso No utilice este monitor cerca del agua. Por ejemplo, cerca de una baera, lavabo, fregadero de cocina o lavadero, en un stano hmedo o cerca de una piscina, etc. Utilcelo nicamente con un carro o soporte recomendado por el fabricante o vendido con el monitor. El montaje en pared o estante debe realizarse siguiendo las instrucciones del fabricante y utilizando un kit de montaje aprobado por el mismo. No coloque este monitor sobre un carro, soporte o mesa inestable. El monitor podra caerse y causar lesiones graves a un nio o adulto, adems de daos importantes al equipo. Las ranuras y aberturas del gabinete, en la parte posterior o inferior, se proporcionan para ventilacin y para asegurar un funcionamiento fiable del monitor y protegerlo contra el sobrecalentamiento. Estas aberturas no deben bloquearse ni cubrirse. Nunca deben obstruirse colocando el monitor sobre una cama, sof, alfombra u otra superficie similar. Este monitor nunca debe colocarse cerca o encima de un radiador o fuente de calor. Este monitor no debe instalarse en espacios empotrados, como estanteras, a menos que se proporcione una ventilacin adecuada. No coloque objetos sobre el cable de alimentacin. No ubique este monitor en lugares donde el cable pueda ser pisado o daado. No doble, aplaste ni dae el cable de alimentacin. Nunca introduzca objetos de ningn tipo en este monitor a travs de las ranuras del gabinete, ya que podran tocar puntos de voltaje peligroso o provocar cortocircuitos que podran causar incendios o descargas elctricas. Nunca derrame lquidos de ningn tipo sobre o dentro del monitor. Este equipo no es adecuado para su uso en lugares donde puedan estar presentes nios. Este equipo no est destinado a la visualizacin de seales de transmisin de televisin. Desconecte la alimentacin antes de la limpieza. Mantenimiento Para mayor proteccin de este monitor, cuando no se utilice durante perodos prolongados, desconctelo de la toma de corriente. Esto evitar daos por sobretensiones en la lnea elctrica. Desconecte el monitor de la toma de corriente antes de limpiarlo. No utilice limpiadores lquidos ni en aerosol. Utilice un pao hmedo para la limpieza. Limpie la superficie de la pantalla LCD con un pao sin pelusa y no abrasivo. Evite el uso de soluciones de limpieza o limpiavidrios. VIII Desconecte el monitor de la toma de corriente y solicite servicio tcnico a personal calificado en los siguientes casos:

Cuando el cable de alimentacin o el enchufe estn daados o desgastados. Si se ha derramado lquido dentro del monitor. Si el monitor ha estado expuesto a lluvia o agua. Si el monitor no funciona normalmente siguiendo las instrucciones de uso. Ajuste nicamente los controles indicados en las instrucciones, ya que un ajuste incorrecto puede causar daos y requerir una reparacin extensa por parte de un tcnico calificado. Si el monitor se ha cado o el gabinete ha sufrido daos. Cuando el monitor presente un cambio notable en su rendimiento, lo que indica la necesidad de servicio tcnico. Advertencia El uso excesivo puede daar la visin. Tome un descanso de 10 minutos por cada 30 minutos de uso de la pantalla. Los nios menores de 2 aos no deben utilizar pantallas. Para nios de 2 aos o ms, el tiempo de uso debe limitarse a menos de una hora al da. Evite mostrar patrones fijos en la pantalla durante largos perodos para prevenir quemado de pantalla o persistencia de imagen (efectos de imagen residual). Desconecte inmediatamente el monitor de la toma de corriente y solicite servicio tcnico en los siguientes casos:

Si el cable o enchufe de alimentacin est daado. Si se ha derramado lquido o han cado objetos dentro del monitor. Si el monitor ha estado expuesto a lluvia o agua. Si el monitor se ha cado o el gabinete est daado. Si observa daos estructurales, como grietas o inestabilidad anormal. Si el monitor no funciona normalmente siguiendo las instrucciones de uso. Condiciones ambientales Solo para uso en interiores, salvo que se especifique lo contrario No instalar en lugares donde la ventilacin est restringida u obstruida No exponer el monitor a temperaturas, humedad o condensacin excesivas (consulte las especificaciones del producto para ms informacin) PRECAUCIONES IMPORTANTES P S E Explicacin de los smbolos grficos:

Exclamation-Triangle Este smbolo advierte al usuario que se ha incluido informacin importante relacionada con el funcionamiento y el mantenimiento de esta unidad. Por lo tanto, dicha informacin debe leerse cuidadosamente para evitar cualquier problema. El cumplimiento de las distintas normas internacionales vara segn el modelo. Consulte la etiqueta de certificacin ubicada en la parte posterior de este monitor para confirmar qu normas han sido efectivamente obtenidas. UL 62368-1:2025 CSA C22.2 No. 62368-1:25 IEC 62368-1:2018 IEC 62368-1:2022 EN 55032 EN55035 47 CFR FCC Parte 15, Subparte B, Clase A IX F R A MESURES DE SCURIT IMPORTANTES Dclaration de la Federal Communications Commission (FCC) Cet appareil de classe A est conforme la partie 15 des rgles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas causer dinterfrences nuisibles. 2. Cet appareil doit accepter toute interfrence reue, y compris celles pouvant provoquer un fonctionnement indsirable. Remarque: Cet quipement a t test et dclar conforme aux limites applicables aux appareils numriques de classe A, conformment la partie 15 des rgles de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles lorsque lquipement est utilis dans un environnement commercial. Cet quipement gnre, utilise et peut mettre de lnergie radiofrquence et, sil nest pas install et utilis conformment au manuel dinstructions, peut causer des interfrences nuisibles aux communications radio. Lutilisation de cet quipement dans une zone rsidentielle est susceptible de provoquer des interfrences nuisibles, auquel cas lutilisateur devra corriger ces interfrences ses propres frais. Lutilisateur est encourag essayer de corriger les interfrences par une ou plusieurs des mesures suivantes:

Rorienter ou dplacer lantenne de rception. Augmenter la distance entre lquipement et le rcepteur. Brancher lquipement sur une prise appartenant un circuit diffrent de celui auquel le rcepteur est connect. Consulter le revendeur ou un technicien radio/TV expriment pour obtenir de laide. Mise en garde FCC Afin dassurer la conformit continue, tout changement ou modification non expressment approuv par Clinton Electronics concernant la conformit peut annuler le droit de lutilisateur utiliser cet quipement.

(Exemple : utiliser uniquement des cbles dinterface blinds lors de la connexion un ordinateur ou des priphriques.) Dclaration dexposition aux rayonnements FCC Cet quipement est conforme aux limites dexposition aux rayonnements RF de la FCC tablies pour un environnement non contrl. Il doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre plac au mme endroit ni fonctionner conjointement avec une autre antenne ou un autre metteur. Les antennes utilises doivent tre installes de manire maintenir une distance dau moins 20 cm avec toute personne et ne doivent pas tre co-localises avec dautres antennes ou metteurs. CE Avertissement : lutilisation de cet quipement dans un environnement rsidentiel peut provoquer des interfrences radio ATTENTION:

RISQUE DEXPLOSION SI LA BATTERIE EST REMPLACE PAR UN TYPE INCORRECT. LIMINER LES BATTERIES USAGES CONFORMMENT AUX INSTRUCTIONS. 1. Un cordon dalimentation de type blind est requis afin de respecter les limites dmissions FCC et dviter les interfrences avec la rception radio et tlvision proximit. Il est essentiel dutiliser uniquement le cordon dalimentation fourni. 2. Utilisez uniquement des cbles blinds pour connecter les priphriques dentre/sortie cet quipement. 3. Toute modification non expressment approuve par la partie responsable de la conformit peut annuler votre droit dutiliser cet quipement. X MESURES DE SCURIT IMPORTANTES A R F ATTENTION RISQUE DE CHOC LECTRIQUE. NE PAS OUVRIR. AFIN DE RDUIRE LE RISQUE DE CHOC LECTRIQUE, NE PAS DMONTER LAPPAREIL. AUCUNE PICE RPARABLE PAR LUTILISATEUR LINTRIEUR. CONFIER TOUTE RPARATION UN PERSONNEL QUALIFI. Le symbole de lclair termin par une flche, lintrieur dun triangle quilatral, est destin alerter lutilisateur de la prsence dune tension dangereuse non isole lintrieur du botier du produit, dune amplitude suffisante pour constituer un risque de choc lectrique pour les personnes. Le point dexclamation lintrieur dun triangle quilatral est destin avertir lutilisateur de la prsence dinstructions importantes concernant le fonctionnement et lentretien (maintenance) dans la documentation accompagnant lappareil. Linstallation doit tre effectue par un technicien qualifi et doit tre conforme lensemble des rglementations locales en vigueur. Avertissements de scurit Lisez attentivement toutes ces instructions. Conservez ces instructions pour consultation ultrieure. Respectez tous les avertissements et instructions indiqus sur le moniteur. Si un connecteur dalimentation 3 broches est fourni avec le cordon dalimentation (quil sagisse dun cordon fourni ou dune alimentation externe), branchez-le dans une prise mise la terre (relie la terre) 3 broches. Si vous ne parvenez pas insrer la fiche dans la prise, contactez un lectricien qualifi afin de remplacer la prise. Ne neutralisez pas la mise la terre du cordon dalimentation, par exemple en utilisant un adaptateur 2 broches ou en retirant la broche de terre. La broche de mise la terre est un lment de scurit essentiel. Ce moniteur doit tre utilis uniquement avec le type de source dalimentation indiqu sur ltiquette signaltique. En cas de doute sur le type dalimentation utiliser, consultez les spcifications du produit en ligne ou contactez un technicien qualifi. Ne surchargez pas les prises murales, les multiprises et/ou les rallonges lectriques, car cela pourrait provoquer un incendie ou un choc lectrique. Nutilisez pas daccessoires non recommands par le fabricant du moniteur, car ils peuvent prsenter des risques. Lorsque des pices de rechange sont ncessaires, assurez-vous que le technicien de service utilise des pices spcifies par le fabricant et prsentant les mmes caractristiques que les pices dorigine. Toute substitution non autorise peut entraner un risque dincendie, de choc lectrique ou dautres dangers. Le moniteur doit tre connect un quipement informatique (ITE) dot dune source dalimentation limite (LPS) approuve par Underwriters Laboratories (UL) ou TV. Nessayez pas de rparer ce moniteur vous-mme, car louverture ou le retrait des capots peut vous exposer des tensions dangereuses ou dautres risques. Confiez toutes les rparations un personnel qualifi. Aprs toute intervention ou rparation sur ce moniteur, demandez au technicien deffectuer des contrles de scurit afin de vrifier que lappareil est en bon tat de fonctionnement. Utilisation prvue Ce produit est destin uniquement un usage professionnel et commercial dans le cadre dun systme de vidosurveillance et de surveillance. XI F R A MESURES DE SCURIT IMPORTANTES Prcautions dutilisation Nutilisez pas ce moniteur prs de leau. Par exemple, prs dune baignoire, dun lavabo, dun vier de cuisine ou dune cuve de lessive, dans un sous-sol humide, ou proximit dune piscine, etc. Utilisez uniquement un chariot ou un support recommand par le fabricant ou vendu avec le moniteur. Le montage mural ou sur tagre doit suivre les instructions du fabricant et utiliser un kit de montage approuv par celui-ci. Ne placez pas ce moniteur sur un chariot, un support ou une table instable. Le moniteur pourrait tomber et causer des blessures graves un enfant ou un adulte, ainsi que des dommages importants lappareil. Les fentes et ouvertures du botier, larrire ou en dessous, sont prvues pour la ventilation afin dassurer un fonctionnement fiable du moniteur et de le protger contre la surchauffe. Ces ouvertures ne doivent pas tre obstrues ni couvertes. Elles ne doivent jamais tre bloques en plaant le moniteur sur un lit, un canap, un tapis ou toute autre surface similaire. Ce moniteur ne doit jamais tre plac proximit ou au-dessus dun radiateur ou dune bouche de chauffage. Ce moniteur ne doit pas tre install dans un espace encastr, comme une bibliothque, sauf si une ventilation adquate est assure. Ne placez aucun objet sur le cordon dalimentation. Ninstallez pas ce moniteur dans un endroit o le cordon pourrait tre pitin ou endommag. aux surtensions lectriques. Dbranchez ce moniteur de la prise murale avant de le nettoyer. Nutilisez pas de nettoyants liquides ni en arosol. Utilisez un chiffon humide pour le nettoyage. Nettoyez la surface de lcran LCD avec un chiffon non pelucheux et non abrasif. vitez dutiliser toute solution de nettoyage ou nettoyant pour vitres. Dbranchez ce moniteur de la prise murale et confiez toute rparation un personnel qualifi dans les conditions suivantes :

Lorsque le cordon dalimentation ou la fiche est endommag(e) ou effiloch(e). Si du liquide a t renvers dans le moniteur. Si le moniteur a t expos la pluie ou leau. Si le moniteur ne fonctionne pas normalement en suivant les instructions dutilisation. Rglez uniquement les commandes couvertes par les instructions dutilisation, car un rglage incorrect des autres commandes peut entraner des dommages et ncessitera souvent une intervention importante dun technicien qualifi pour rtablir le fonctionnement normal du moniteur. Si le moniteur est tomb ou si le botier a t endommag. Lorsque le moniteur prsente un changement notable de performance, indiquant un besoin de rparation. Avertissement Une utilisation excessive peut nuire votre Ne pliez pas, ncrasez pas et nendommagez vision. pas le cordon dalimentation. Ninsrez jamais dobjets de quelque nature que ce soit dans ce moniteur par les ouvertures du botier, car ils pourraient entrer en contact avec des points de tension dangereux ou provoquer des courts-circuits pouvant entraner un incendie ou un choc lectrique. Ne renversez jamais de liquide de quelque nature que ce soit sur ou dans le moniteur. Cet quipement ne convient pas une utilisation dans des lieux o des enfants sont susceptibles dtre prsents. Cet quipement nest pas destin laffichage de signaux de diffusion tlvisuelle. Dbranchez lalimentation avant le nettoyage. Entretien Pour une protection supplmentaire, lorsque ce moniteur est laiss sans surveillance et inutilis pendant de longues priodes, dbranchez-le de la prise murale. Cela vitera les dommages dus Faites une pause de 10 minutes toutes les 30 minutes dutilisation de lcran. Les enfants de moins de 2 ans ne devraient pas tre exposs aux crans. Pour les enfants de 2 ans et plus, le temps dcran devrait tre limit moins dune heure par jour. vitez dafficher des images fixes pendant de longues priodes afin de prvenir les brlures dcran ou la persistance dimage (effets de rmanence). Dbranchez immdiatement votre moniteur de la prise murale et confiez la rparation un personnel qualifi dans les conditions suivantes :

Si le cordon dalimentation ou la fiche est endommag(e). Si du liquide a t renvers ou si des objets sont tombs dans le moniteur. Si le moniteur a t expos la pluie ou leau. Si le moniteur est tomb ou si le botier est endommag. Si vous remarquez des dommages structurels, XII MESURES DE SCURIT IMPORTANTES A R F tels que des fissures ou un vacillement anormal. Si le moniteur ne fonctionne pas normalement en suivant les instructions dutilisation. Conditions environnementales Utilisation en intrieur uniquement sauf indication contraire Ne pas installer dans un endroit o la ventilation est restreinte ou obstrue Ne pas exposer le moniteur des tempratures, une humidit ou une condensation excessives (consulter les spcifications du produit pour plus dinformations) Explication des symboles graphiques:

Exclamation-Triangle Ce symbole avertit lutilisateur que des informations importantes concernant le fonctionnement et lentretien de cet appareil sont incluses. Il est donc recommand de lire attentivement ces informations afin dviter tout problme. Les diffrentes conformits aux normes internationales sont obtenues selon le modle. Veuillez vrifier ltiquette de certification situe larrire de ce moniteur afin de confirmer quelles normes sont effectivement respectes. UL 62368-1:2025 CSA C22.2 No. 62368-1:25 IEC 62368-1:2018 IEC 62368-1:2022 EN 55032 EN55035 47 CFR FCC Partie 15, Sous-partie B,Classe A XIII Hardware Overview: I/O Connections 1 2 3 4 5 6 7 ON OFF 8 9 10 11 12 13 14 Connections (varies by model) 1. DC 24V Input (barrel plug) 2. DC 24V Input (4-Pin DIN) 3. AC 100~240V Input 4. On/Off Power Switch 8. HDMI Input 9. VGA *Firmware Update Only - No Video In/Out 10. BNC Input/Output 11. HD-SDI Input/Output 5. RJ45 Network (or PoE in, PoE+ or PoE++) 12. USB 6. 2-Pin Alarm Input (+/-) 7. 4-Pin Alarm Input (+/-) 13. SD Card Slot 14. Micro SD Card Slot Input & Output connections will vary by model. Always check specification data at www.clintonelectronics. com for most up-to-date model information. If equipped, VGA connections are for firmware updates only. These connections will not work for video input/output. If model has dual power options, (DC24V or AC110V) never connect both power sources. Doing so can damage the unit and can be an electrical and/or fire hazard. USB Note: USB connections only support devices with low electrical load, total Amps of connected device must less than 0.5 Amps(ex: mouse, keyboard, pen drive...) 1 Hardware Overview: PVM FRONT 1. LCD Screen 2. RGB LEDs 3. LED 4. IR Remote Control Sensor 5. Camera 6. Micro SD Card Access Cover (location varies by model) BACK 1. Recessed VESA Mounting Holes (hole pattern varies by model) 2. I/O Connections 3. Power Status LED (RVM) 3. External VESA Mounting Holes (hole pattern varies by model) 4. LCD Controls (not available on 10 and smaller models) 1 4 5 2 3 4 5 6 2 1 2 3 Actual features may vary from the image shown. Always check specification data at www.clintonelectronics. com for most up-to-date model information. 2 Hardware Overview: Connect PVM FRONT 1. LCD Screen 2. RGB LEDs 3. Push Button 4. Camera 5. LED 6. IR Remote Control Sensor 1 3 4 BACK 1. I/O Connections 2. External VESA Mounting Holes (hole pattern varies by model) 2 6 1 2 Actual features may vary from the image shown. Always check specification data at www.clintonelectronics. com for most up-to-date model information. 3 Hardware Overview: Remote Control IR Remote Controls SOURCE: No function POWER: Turns LCD Screen ON/OFF (does not turn off camera) SWAP: No function PIP: No function MUTE: Turns Audio ON/OFF (if unit supports audio) MENU: Push once to display OSD Menu SELECTION ARROWS: Navigate through OSD menu AUTO: No function ENTER: Select a highlighted menu item to open submenu EXIT: When in a selection, press to exit out from that menu item VOL+ / VOL - : Increase/Decrease audio LCD Controls (located on back of PVM) POWER: Turns LCD Screen ON/OFF (does not turn off camera) DOWN: Navigate through menu options Down AUTO: Exit or go back to previous menu screen UP: Navigate through menu options Up MENU: Push once to display OSD Menu, press on a highlighted item to open submenu LCD Controls are not on 10 and smaller units. LCD control is only possible using the IR Remote. 4 Basic Installation 1 Install VESA bracket to PVM:

Remove the cover plate (if equipped) on the back-side of the PVM and set aside. Install the PVM onto appropriate VESA mounting bracket, following instructions supplied with the mounting bracket.

*Mounting Bracket Not Included, Sold Separately. Mounting fasteners are not included with the PVM! Use the mounting fasteners that are included with the mounting bracket. VESA Mounting Bracket

*Actual VESA bracket used, VESA hole patterns, and PVM will vary from the example shown. This PVM monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard sized screws used are M4 for VESA 75x75, 100x100, 100x200 & M6 for VESA 200x200 up to 400x400. The screw length will vary depending on the thickness of the mounting bracket. Screws (fastners) are included with the mounting bracket. Use four screws when installing. Exclamation-Triangle ATTENTION:

A mounting bracket is required for installation. The mounting bracket is sold separately and is not included with the product. Installation shall be performed in accordance with the instructions and documentation provided with the mounting bracket. The installer is solely responsible for ensuring that the selected mounting bracket is rated to support the full weight of the PVM/monitor. Clinton Electronics shall not be liable for the use of third-party mounting brackets that are inadequate or unsuitable for the intended application. The installer must verify that the mounting surface is structurally sound and capable of safely supporting the combined weight of the unit and all associated hardware. Installation on walls, ceilings, or other structures is performed at the customers own risk and responsibility. Not all mounting surfaces are suitable for installation. Prior to installation, the mounting location must be thoroughly inspected to confirm it can support the load and ensure safe, secure operation. Clinton Electronics shall not be responsible for any damage, injury, or loss resulting from improper installation, inadequate mounting surfaces, structural modifications, or acts of nature. The product warranty does not cover damage caused by improper installation, remodeling, or natural disasters. Failure to comply with these requirements may result in the voiding of the warranty. Un support de montage est requis pour linstallation. Ce support est vendu sparment et nest pas fourni avec le produit. Linstallation doit tre effectue conformment aux instructions et la documentation fournies avec le support. Il incombe linstallateur de sassurer que le support de montage choisi est conu pour supporter le poids total du moniteur/PVM. Clinton Electronics dcline toute responsabilit en cas dutilisation de supports de montage tiers inadquats ou non adapts lapplication prvue. Linstallateur doit vrifier que la surface de montage est structurellement saine et capable de supporter en toute scurit le poids combin de lappareil et de tous les accessoires associs. Linstallation sur les murs, les plafonds ou autres structures est effectue aux risques et prils du client. Toutes les surfaces de montage ne sont pas adaptes. Avant linstallation, lemplacement de montage doit tre soigneusement inspect afin de confirmer sa capacit supporter la charge et dassurer un fonctionnement sr. Clinton Electronics dcline toute responsabilit en cas de dommages, blessures ou pertes rsultant dune installation incorrecte, de surfaces de montage inadquates, de modifications structurelles ou de catastrophes naturelles. La garantie du produit ne couvre pas les dommages causs par une installation incorrecte, des travaux de rnovation ou des catastrophes naturelles. Le non-respect de ces exigences peut entraner lannulation de la garantie. 5 Basic Installation 2 Connect Power:

Before connecting the power cable, make sure that the power supply is not connected to main power source, and check that the power switch (if equipped) is set to the OFF position. Connect the DC power cord from the power supply into the DC24V jack on the PVM.

*Power Supply Not Included, Sold Separately. 1. Plug the DC connector properly and do not have loose connection between DC jack and the plug as this can result into poor connection and cause damage. 2. Do not bend the DC wire and the DC connector. It will cause damage of the wire as this can result into fire. 3. Do not coil the wire and avoid the wire being pressed under heavy objects. It will cause an overload and damage of the wire as this can result into fire. Main Power Outet From Power Supply For PVM models supporting PoE:

Some PVM models support PoE (Power Over Ethernet). If the PVM model supports PoE the label for the IP Camera will denote (PoE). If the network port does not say PoE that model does not support PoE power and must be powered separately from DC24V or AC power. If using PoE power connect quality Cat5e/CAT6 network cable to the network port marked PoE. Ensure the connected PoE switch or injector has enough power for the PVM. If underpowered the camera might function and be discoverable on the network, but the main PVM will not turn on (there will be no screen image). PoE NOT Supported PoE Supported Exclamation-Triangle ATTENTION:

Do not connect power to the PVM while the power supply is energized. Always unplug the power supply from the main power source first; hot-plugging can damage the monitor and void the warranty.. Only use DC or AC power! For PVM models that support being powered either from DC24V or AC100~240V power: DO NOT CONNECT DC24V & AC110V POWER SIMULTANEOUSLY. Connecting both will cause damage to the device. 6 Basic Installation 3 Connect Network/Video Cable(s):

Depending on the PVM model, connect network cable (if not used for PoE power) or coaxial cable for transferring the built-in camera image to a connected recorder (DVR/NVR/VMS). DC24V Power Supply Network Switch to NVR/VMS

*Actual connections shown will vary by model. 4 Turn Power ON:

After making the power and network/video connections, plug the power supply into a wall outlet and set the On/Off power switch (if equipped) to the ON position. Replace the cover removed from step 1 after all cable connections are complete and the unit has begun to power On. For models with RVM (Rated Voltage Monitoring) LED status light:

A LED indicator (on the rear of the PVM) will illuminate when the PVM is receiving power. The electrical components can fail if it is receiving too little, or too much power. An under-powered PVM might work initially, but will often fail if the power is not addressed. GREEN: Safe voltage, normal operation RED: Under voltage, check power. Use shorter power run, larger gauge wire, or larger power supply BLUE: Over voltage, check power. Adjust power supply output if supported. 5 Camera Boot-Up:

For IP camera PVM models: While the IP camera is booting up, colored bars or a Waiting for Camera message will be shown on the screen. This will be displayed on the screen for approximately 30-60 seconds. The live camera image will display on the screen after the camera has successfully booted up. For analog camera PVM models: The camera image will display shortly after power On. Boot-Up Camera Image 7 OSD / VIDEO SETTINGS Clinton PVMs come preset with settings that are optimized for most applications. Adjust the picture as needed. To access the OSD Menu, press the MENU button on the remote or using the controls on the backside of the PVM.

VIDEO SETTINGS Contrast Brightness Saturation

Tint Sharpness Color Temperature

50 50 70 50 50 Camera 1080p 30Hz Contrast:

Adjust to set the white level so that the images are at their brightest without losing definition in the white portions of the image. Setting the too high will result in an over-saturated image. Brightness:

Adjust to set the black level so that the images are at their brightest while the black portions are still black. Do not adjust too high where the black portions of the image become gray or the image will have a washed out appearance. Saturation:

Adjust the color saturation of the video image; decrease for a more monochrome (black & white) image, or increase for a more colorful/vibrant image. Tint:

To adjust the color balance towards more green or more magenta. Sharpness:

Adjust lower if the image appears too grainy or pixelated. Increase if the image appears too soft. Color Temperature:

Adjusts the color temperature of the screen image. A low color temperature will make the screen reddish. A high color temperature will make the screen bluish. The OSD Menu will automatically timeout/disappear after 30 seconds of no activity. (time can be adjusted) These settings do not adjust the actual camera image. Its recommended to verify that the image from the camera looks correct before adjusting these monitor settings. Camera settings are adjusted separately, through the camera. The method of adjusting camera settings varies depending on the camera type. 8 0 OSD / DISPLAY DISPLAY Aspect Ratio Image Mode Full Screen Camera Motion Dwell Time 5

Camera 1080p 30Hz Aspect Ratio:

Select the display aspect ratio (Full Screen, Cinema Scope, 4:3, Pillar Box Expand, 1:1). Select Full Screen to correctly display the camera image without stretching or distortion. Image Mode:

Choose what displays on the LCD. Image Mode options will vary by model. Camera: Only the camera image is displayed, motion detection features are disabled. Logo Motion: When there is no motion, the PVM will display a selected store logo. Once motion is detected the camera will be shown on the screen. After there is no motion the screen will switch back to the store logo.

(requires custom programming, contact Clinton Electronics technical support for more info) Motion LED: The camera image is the main and only display; when motion is detected the LED(s) on the front of the PVM will flash until motion is no longer detected. LOGO Logo Alarm: When there is no motion, the PVM will display a selected store logo. Once triggered by an alarm input, the camera will be shown on the screen. After there is no motion, the screen will switch back to the store logo. (requires custom programming, contact Clinton Electronics technical support for more info) Camera SD CARD LOGO LOGO Logo Motion Motion LED Logo Alarm Motion Dwell Time:

Set to adjust how long the screen will display video after motion is detected. Example: If set to 3 Seconds - the screen will switch from the Store Logo image to the camera image. The camera image will remain on the screen until NO motion is detected for a period of 3 seconds. SD CARD SD CARD 9 SD CARD Message ControlSpecial ControlKey LockRecallOnOffOff OSD / AUDIO AUDIO Volume Chime 0 Off

Camera 1080p 30Hz Volume:

Raise or Lower the volume for the Chime. Alternatively, you can use the volume buttons on the remote control to set volume level. Chime:

An audible ding-dong chime is played when motion is detected. Audio is not supported on all models. 10 Message ControlSpecial ControlKey LockRecallOSD TransparencyOnOffOff0 OSD / SYSTEM SETTINGS SYSTEM SETTINGS Language OSD Setting Key Lock Message Control Border LED Recall English

Off

Camera 1080p 30Hz Language:

Display the OSD menu in English or Spanish. Note: Changing the Language does not change the flashing on-

screen message. This must be changed in the Message Control > Message setting. OSD Setting:

Adjust the duration the OSD menu is shown, the position, transparency and rotation on the OSD Menu. Key Lock:

Turning this ON will lock to Menu Buttons located on the back of the PVM, the remote control will still function. The remote control is required to disable Key Lock. Message Control:

Adjust the settings for the overlay text or image banner displayed on the lower portion of the screen. Message On/Off: Turn the on-screen overlay message/banner ON or OFF. This will display on the lower portion of the screen. Message: Select from a variety of banners that display:

Recording in Progress, Monitoring in Progress, etc... Message Flash: Turning Flash ON enables the on-screen message to flash on and off. Adjust the flash rate in seconds (1, 2, 3, etc). Please Return to Cashier: Turning ON enables a large full-

screen message to flash on and off when triggered by an alarm input. Adjust the flash rate in seconds (1, 2, 3, etc). Motion Message Control: Set to ON for the banner to only display when motion is detected. Set to OFF for the banner to be constantly displayed. MESSAGE

(banner) Banner Examples: Shown are some of the available banner options. Some options are available in multiple languages. Images noted with an * (asterisk) have a transparent background.

Banner options and availability subject to change without notice 11 OSD / SYSTEM SETTINGS Border:

Add a colored border around the perimeter of the LCD. Adjustable flash rate, weight, and color options. Border: Turn ON or OFF a colored border around the edge of the screen. Border Flash: Turning Flash ON enables the border to flash on and off Border Color: Set a color option for the border: Red / Yellow

/ Orange / Green / Blue / Magenta / White / Black / Cycle /

Random. Border Width: Adjust the width of the border thicker or thinner. Border On Time: When Border Flash is set to On - adjust the duration the border is On (in seconds). Border Off Time: When Border Flash is set to On - adjust the duration the border is Off (in seconds). BORDER LED:

Adjust the settings for the built-in flashing LED(s). LED styles, numbers, and layouts vary by model. Motion LED Control: Set to ON for the LED/RGB LEDs to only illuminate when motion is detected. Set to OFF for the LED/

RGB LEDs to constantly be illuminated. LED Control: Set to ON to enable the single Yellow LED light. LED RGB Control: Adjust the color of the RGB LEDs; Red /

Green / Yellow / Blue / Magenta / Cyan / White / Color cycle

/ Off. Selecting Color cycle will cycle through all of the colors sequentially. LED Open Time: Adjust how long the LEDs are On when flashing. If set to OFF the LEDs will not illuminate. LED Close Time: Adjust how long the LEDs are Off when flashing. If set to OFF the LEDs will not illuminate. RGB LEDs LED

(LED Control) RGB LEDs Recall:

Resets PVM settings to defaults (does not affect any camera settings). Overlay options, such as MESSAGE (banner) and/or BORDER are not embedded onto actual camera footage. These are only viewable on the PVM screen, they will not be on recorded video if the camera is connected to a recorder. 12 OSD / CAMERA SETTINGS CAMERA SETTINGS Reboot Camera Factory Default Off Off

Camera 1080p 30Hz Reboot Camera:

To reboot the camera, highlight Reboot and press the RIGHT button on the remote. The reboot takes about 1 minute to complete. Factory Default:

To reset all of the settings on the camera to the defaults, highlight Factory Default and press the RIGHT button on the remote. After pressing the RIGHT button, the camera will begin to perform the Factory Default process, during this time the camera will be inaccessible for about 1 minute and perform a reboot. The cameras IP Address should remain unchanged, unless the DHCP server re-assigned a new address. After the camera reboots, the password will need to be reconfigured, as well as any additional camera settings. During the Reboot or Factory Default a color bar screen (white/red/green/blue) or a Waiting for Camera message will display until the camera has finished the reboot or factory default. Camera Reboot & Factory Default are only available on PVM models with a Clinton Electronics IP Camera. This option is not available on PVM models with an analog or HD-SDI/EX-SDI camera. 13 Connect PVM Setup Exclamation-Triangle ATTENTION:

Connect PVMs models (CE-P10E-B, CE-P13E-B, CE-P21E-B, CE-P32E-B, CE-P43E-B) require internet connectivity and a special Company QR Code to complete installation. If there is no internet access, installation can not be completed. If the QR code is missing, installation can not be completed. For full Connect PVM Setup, refer to the Connect PVM User Manual at: https://www.clintonconnect.com/

support ATTENTION: Verify that the following information is completed before proceeding with the installation. Is the Connect PVM installed vertically?

Verify the Connect PVM is installed correctly. It should have a vertical orientation (portrait mode) with the camera located at the bottom of the device. If the device is installed horizontally both the camera feed on connected DVR/NVR and the digital signage content will not display correctly. Do you have the Remote that was included with the PVM?

The included remote is required to complete the initial set up. Keep the remote in a safe place to make any adjustments at a later date. Do you have the Company QR Code?

The company specific QR Code is required to register the device to the correct company. If the QR Code was not provided contact your Clinton Connect admin. Will this be a wired or wireless internet (Wifi) connection?

The Connect PVM is a networked device that requires internet access to function correctly. If this device can not access the internet, it can not be completely setup and will not be able to receive advertising updates. This device will accept either a wired or Wifi internet connection. For best results a wired connection is recommended. Has the network been properly configured?

Depending on the level of network security, some URLs may need to be white-listed on the network. If the required URLs are not added, the initial set up will fail. For a list of the required URLs consult the Networking Requirements document which can be found on www.clintonconnect.com/support 14 Connect PVM Setup Step 1. Press the ENTER button on the included remote to get started. Step 2. Choose a Wifi Network from the list, enter the password, and select Join.

*Hardwired devices will automatically skip this step Step 3. After successful network connection, the device will test its Internet Connection and ping the Clinton Connect Server. Both tests must pass to proceed with the setup. Step 4. Hold the QR code in front of the Connect PVM camera to scan. If the code does not scan, you can also enter it manually. 15 Connect PVM Setup Step 5. Once the QR Code has scanned, verify the correct time and date by selecting YES. If the time is not correct, select NO, then select the correct time from the list. Step 6. Press the ENTER button on the remote to Snap a Photo. This photo is used to help verify the device is installed in the correct location. Choose to Accept or Redo the photo. Step 7. Begin typing the store number when prompted, then choose your store number from the list. Store numbers will only appear if they have been entered previously on Clinton Connect. Step 8. Select the appropriate device group from the list to automatically download assigned content. If there is no content, the device will display the full-

screen camera view until the next deployment to that device or device group. For full Connect PVM Setup, refer to the specific manual at: https://www.clintonconnect.com/support 16 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M8S-B 8 TFT LCD 800 x 600 4:3 (Landscape) 262K [RGB 6 bit]

400 nit 500:1 Viewing Angle (H x V) 140 x 120 Response Time 25ms Mounting Connections VESA 75 & 100 1 BNC Output Power Requirement DC24V MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M8S-B-DG 8 TFT LCD 800 x 600 4:3 (Landscape) 262K [RGB 6 bit]

400 nit 500:1 Viewing Angle (H x V) 140 x 120 Response Time 25ms Mounting Connections VESA 75 & 100 1 BNC Output Power Requirement DC24V Power Consumption 6 Watts / 0.25 Amps Power Consumption 6 Watts / 0.25 Amps Operating Temperature 32F ~ 104F / 0C ~ 40C Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 7.4 x 7.44 x 1.43 187.96mm x 188.98mm x 36.3mm Dimensions (W x H x D) 7.4 x 7.44 x 1.43 187.96mm x 188.98mm x 36.3mm Weight 2.8 lbs / 1.27 kg Weight 2.8 lbs / 1.27 kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M8SD-B 8 TFT LCD 800 x 600 4:3 (Landscape) 262K [RGB 6 bit]

400 nit 500:1 Viewing Angle (H x V) 140 x 120 Response Time 25ms Mounting Connections VESA 75 & 100 1 BNC Output Power Requirement DC24V Power Consumption 12 Watts / 0.5 Amps Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 7.4 x 7.44 x 1.43 187.96mm x 188.98mm x 36.3mm Weight 2.8 lbs / 1.27 kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M10E(B) 10 TFT LCD 1280 x 800 16:10 (Landscape) 16M 350 nit 800:1 Viewing Angle (H x V) 170 x 170 Response Time 25ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/ 100 Base-T (PoE+) Power Requirement DC24V or PoE+

Power Consumption DC24V: 14 Watts PoE+ (IEEE 802.3at): 13.5 Watts Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 9.375 x 7.6 x 1.875 238.125mm x 193mm x 47.625mm Weight 3.4 lbs / 1.54 kgs 17 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M10PE-B 10 TFT LCD 800 x 1280 10:16 (Portrait) 16M 350 nit 800:1 Viewing Angle (H x V) 170 x 170 Response Time 25ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/ 100 Base-T (PoE+) Power Requirement DC24V or PoE+

Power Consumption DC24V: 14 Watts PoE+ (IEEE 802.3at): 13.5 Watts Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 6.17 x 10.75 x 1.53 156.7mm x 273.05mm x 39mm Weight 3.5 lbs / 1.58 kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M16RE-B 15.7 Round LCD w/ WLED Backlight 960 x 960 1:1 16.7M (8 BIT) 700 nit 1000:1 Viewing Angle 89 x 89 x 89 x 89 Response Time 8ms Mounting Connections VESA 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 65W / 2.71A MODEL Display Resolution Aspect Ratio Color Depth Brightness CE-M10PEB+6 10 TFT LCD | 5.99 TFT LCD 800 x 1280 | 1440 x 720 10:16 (Portrait) | 2:1 (Landscape) 16M 400 nit | 400 nit Contrast Ratio 800:1 | 1500:1 Viewing Angle (H x V) 170 x 170 | 160 x 160 Response Time 29ms | 30ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/ 100 Base-T (PoE+) 1 - HDMI Input for Lower Monitor Power Requirement DC24V or PoE+

Power Consumption DC24V: 19.2 Watts PoE+ (IEEE 802.3at): 13 Watts Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 6.19 x 13.36 x 1.53 157.4mm x 339.4mm x 39mm Weight 4.5 lbs / 2.04 kgs MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M21E-B 21.5 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 250 nit 1000:1 Viewing Angle (H x V) 178 x 178 Response Time 10ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 18 Watts / 0.75A Operating Temperature 32F ~ 104F / 0C ~ 40C Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 20.625 x 20.625 x 2.67 523.875mm x 523.875mm x 67.8mm Dimensions (W x H x D) 19.8125 x 13.5625 x 1.765 503.25mm x 344.5mm x 44.885mm Weight 17.8 lbs / 8.07 kgs Weight 10.6 lbs / 4.8 kgs 18 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M21PE-B 21.5 LED Backlight LCD 1080 x 1920 9:16 (Portrait) 16.7M (8 BIT) 350 nit 1000:1 Viewing Angle (H x V) 178 x 178 Response Time 18ms Mounting VESA 75 & 100 Connections 1 - RJ45 Ethernet 10/100Mbps 1 Alarm Input 1 Alarm Output Power Requirement DC24V MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M24RE-B 23.6 Round LCD w/ WLED Backlight 848 x 848 1:1 16.7M (8 BIT) 700 nit 4000:1 Viewing Angle 89 x 89 x 89 x 89 Response Time 8ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 75W / 3.2A Power Consumption 20.7 Watts (0.86 Amps) Operating Temperature 32F ~ 104F / 0C ~ 40C Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 11.7 x 21.4 x 1.5 297.2mm x 543.5mm x 38.1mm Weight 13.1 lbs / 5.94kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M24E-SS 23.8 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 1,000 nit 1,000:1 Viewing Angle (H x V) 178 x 178 Response Time 14ms Mounting Connections VESA 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 45 Watts / 1.8A Dimensions (W x H x D) 26.5 x 28.015 x 2.675 673.05mm x 711.59mm x 67.94mm Weight 22.25 lbs / 10.09 kgs MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M27E(B) 27 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 300 nit 3000:1 Viewing Angle 178 x 178 Response Time 6.5ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 36 Watts / 1.5A Operating Temperature 32F ~ 104F / 0C ~ 40C Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 24.03 x 16.76 x 2.63 610.4mm x 425.8mm x 67mm Dimensions (W x H x D) 24.375 x 16 x 1.875 619.125mm x 406.4mm x 47.625mm Weight 27.6 lbs / 12.519 kgs Weight 13.96 lbs / 6.33 kgs 19 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M27E-B-VF 27 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 300 nit 3000:1 Viewing Angle (H x V) 178 x 178 Response Time 6.5ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 36 Watts / 1.5A Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 24.375 x 16 x 1.875 619.125mm x 406.4mm x 47.625mm Weight 13.96 lbs / 6.33 kgs MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-27EPVM-KR4 27 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 300 nit 3000:1 Viewing Angle (H x V) 178 x 178 Response Time 6.5ms Mounting Connections VESA 75, 100, & 100 x 200 1 BNC Input / 2 BNC Outputs Power Requirement DC24V Power Consumption 45 Watts MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M27-HD-B 27 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 300 nit 3000:1 Viewing Angle (H x V) 178 x 178 Response Time 12ms Mounting VESA 75 & 100 Connections 1 HDMI Input 1 EX-SDI / HD-SDI Output 1 BNC (Analog) Input 1 BNC (Analog) Output Power Requirement DC24V Power Consumption 26.88 Watts Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 25 x 17.25 x 3.1 635mm x 438.15mm x 78.74mm Weight 19.2 lbs / 8.708kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M32E(B) 32 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 350 nit 3000:1 Viewing Angle (H x V) 178 x 178 Response Time 6.5ms Mounting Connections VESA 75 & 100 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 48 Watts / 2A Operating Temperature 32F ~ 104F / 0C ~ 40C Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 25 x 17.25 x 3 635mm x 438.15mm x 76.2mm Dimensions (W x H x D) 28.375 x 18.4 x 2.2 720.73mm x 467.36mm x 55.88mm Weight 18 lbs / 8.16kg Weight 21.23 lbs / 9.63 kgs 20 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M32-HD-B 32 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 350 nit 3000:1 Viewing Angle (H x V) 178 x 178 Response Time 6.5ms Mounting VESA 100 & 100 x 200 Connections 1 HDMI Input 1 EX-SDI / HD-SDI Output 1 BNC (Analog) Input 1 BNC (Analog) Output Power Requirement DC24V or 110VAC Power Consumption 45.58 Watts (1.9A @ DC24V / 0.414A @ AC110V) Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 29.25 x 19.625 x 3.1 742.95mm x 498.475mm x 78.74mm Weight 29.05 lbs / 13.17kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M43HD 42.5 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 450 nit 3000:1 Viewing Angle (H x V) 178 / 178 Response Time 8ms Mounting VESA 100x200, 200 (M6), 200 x 400 (M6) Connections 1 HDMI Input 1 EX-SDI / HD-SDI Output 1 BNC (Analog) Input 1 BNC (Analog) Output Power Requirement DC24V or 110VAC Power Consumption 66 Watts Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 38.875 x 24.75 x 3.1 987.43mm x 628.65mm x 78.74mm Weight 49.2 lbs / 22.31 kgs MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M43E(B) 43 LED Backlight LCD 1920 x 1080 16:9 (Landscape) 16.7M (8 BIT) 500 nit 4000:1 Viewing Angle (H x V) 178 x 178 Response Time 8ms Mounting Connections VESA 100, 100x200 (M4), 200x200 (M6) 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V or AC110V Power Consumption 58 Watts / 2.42 Amps Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 38 x 24 x 3 965.2mm x 609.6mm x 76.2mm Weight 38.6 lbs / 17.5 kgs MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-M55E-B 55 WLED Backlight LCD (AMVA3) 3840 x 2160 16:9 (Landscape) 1.07B, 100% sRGB (10 BIT) 500 nit 4000:1 Viewing Angle 89 x 89 x 89 x 89 Response Time 8.5ms Mounting Connections VESA 200 x 200, 200 x 300 (M6) 1 - RJ45 Ethernet 10/100Mbps Power Requirement DC24V Power Consumption 124W max (10%) / 5.17A Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 48.75 x 29.98 x 2.41 1298.2mm x 761.6mm x 61.3mm Weight 47 lbs / 21.32 kgs 21 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-P10E-B 10 TFT LCD 800 x 1280 10:16 (Portrait) 16M 350 nit 800:1 Viewing Angle (H x V) 170 x 170 Response Time 25ms Mounting VESA 75 & 100 MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio Viewing Angle CE-P13E-B 13.3 LED Backlight LCD (AHVA) 1080 x 1920 9:16 (Portrait) 16.7M (8 BIT) 800 nit 800:1 89 x 89 x 89 x 89 Response Time 25ms Mounting VESA 75 & 100 Connections 1 RJ45 Ethernet Port - Camera Feed Only 1 RJ45 Ethernet Port - Media/Content Only 1 Terminal Block Alarm Input Connections 1 RJ45 Ethernet Port - Camera Feed Only 1 RJ45 Ethernet Port - Media/Content Only 1 Terminal Block Alarm Input Power Requirement DC24V Power Consumption 19.2 Watts Power Requirement DC24V Power Consumption 24 Watts / 1A Operating Temperature 32F ~ 104F / 0C ~ 40C Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 6.18 x 11.35 x 1.65 157mm x 288.17mm x 41.88mm Dimensions (W x H x D) 7.65 x 13.97 x 1.57 194.31mm x 363.47mm x 39.37mm Weight 3.6 lbs / 1.63 kg Weight 5.45 lbs / 2.245 kg MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-P21E-B 21.5 LED Backlight LCD 1080 x 1920 9:16 (Portrait) 16.7M (8 BIT) 350 nit 1000:1 MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-P32E-B 32 WLED Backlight LCD (AMVA3) 1080 x 1920 9:16 (Portrait) 16.7M (8 BIT) 400 nit 4,000:1 Viewing Angle (H x V) 178 x 178 Response Time 18ms Viewing Angle (H x V) 178 / 178 Response Time 8ms Mounting VESA 75 & 100 Mounting VESA 75, 100, & 100 x 200 Connections 1 RJ45 Ethernet Port - Camera Feed Only 1 RJ45 Ethernet Port - Media/Content Only 1 Terminal Block Alarm Input 1 Terminal Block Alarm Output Power Requirement DC24V Power Consumption 36 Watts / 1.5A Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 11.65 x 21.7 x 1.52 296mm x 551.36mm x 38.84mm Weight 10.05 lbs / 4.55 kg Connections 1 RJ45 Ethernet Port - Camera Feed Only 1 RJ45 Ethernet Port - Media/Content Only 1 Terminal Block Alarm Input Power Requirement DC24V Power Consumption 69 Watts / 2.9A Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 16.52 x 30.18 x 2.14 419.65mm x 766.6mm x 54.4mm Weight 21.6 lbs / 9.79 kg 22 SPECIFICATIONS MODEL Display Resolution Aspect Ratio Color Depth Brightness Contrast Ratio CE-P43E-B 43 WLED Backlight LCD (AMVA3) 1080 x 1920 9:16 (Portrait) 16.7M (8 BIT) 500 nit 4000:1 Viewing Angle (H x V) 178 x 178 Response Time 8ms Mounting VESA 200x200, 200x400 (M6) Connections 1 RJ45 Ethernet Port - Camera Feed Only 1 RJ45 Ethernet Port - Media/Content Only 1 Terminal Block Alarm Input Power Requirement DC24V or 110VAC Power Consumption 70 Watts / 2.75A Operating Temperature 32F ~ 104F / 0C ~ 40C Dimensions (W x H x D) 22.375 x 40 x 3 568.325mm x 1016mm x 76mm Weight 37.6 lbs / 17.05 kgs 23 24 Clinton Electronics 6701 Clinton Road Loves Park, IL 61111 Technical Support:

1-800-549-6393 Monday~Friday 8:00 am~4:45 pm (CST) www.clintonelectronics.com Actual product may vary slightly from the images shown in this manual. Clinton reserves the right, without notification, to make changes in product design & specification. ver: 05.05.26

Product:

TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name:

clintonelectronics Type Identification:

CE-P21E-B / CE-P21XXXXXXXXXX Label Location Page 1 of 2 Product:

TFT LCD COLOR MONITOR, PUBLIC VIEW MONITOR Brand Name:

clintonelectronics Type Identification:

CE-P21E-B / CE-P21XXXXXXXXXX Page 2 of 2

Covered list attestation FCC application letter Kiwa RF_755_03 Page 1 of 2 06-06-2024

[PLACE COMPANY LOGO HERE OR PUT ON COMPANY LETTERHEAD]

Certification Application Attestation Statements VITA ELECTRONICS CO LTD 0029052990 5th FI 103 Chou Tze St Neihu District 114 Taipei, Taiwan Subject: FCC ID: 2AVEACE-P21-7005 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) VITA ELECTRONICS CO LTD certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

VITA ELECTRONICS CO LTD certifies that, the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered list installed on the device, nor will it be installed by the applicant anytime after certification. Statement for 47 CFR section 2.911(d)(5)(ii)

[Insert Company Name Here] (the applicant) certifies that, as of the date of the filing of this application, the applicant

- is /

- is not (3) identified on the Covered List as an entity producing covered equipment. Date:

City:

Name(2) :

Function:

Telephone number:

Email address:

06/16/2026 5th FI 103 Chou Tze St Neihu District Jack Tseng Electrical Safety Engineer 02-26595977 [email protected] Signature:

1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist .

(2): For FCC it must be the Grantee Code owner or the authorized agent.

(3): double click on the appropriate box and select checked then OK Covered list attestation FCC application letter Kiwa RF_755_03 Page 2 of 2 06-06-2024

[PLACE COMPANY LOGO HERE OR PUT ON COMPANY LETTERHEAD]

Revision Record Sheet:

Revision Section Page Date Remark(s) number number 07-02-2023 1st version issued by RvM 1 1 15-02-2023 Changed Applicant to Company RvdM and added Subject: FCC ID:

06-06-2024 FRN added at certification application and included [Insert Company Name Here] for the statements RvdM 01 02 03 Issued/modified by Function Revision Date

: Richard van de Meer

: Certification assessor

: 03

: 06-06-2024 Verified by Function Date

: Willem Jan Jong

: Team Lead

: 06-06-2024 Released by Function Date of release:

: Axel Gase

: Manager Quality Assurance

: 06-06-2024

FCC, Request for non-disclosure RF_501, Issue 12 Date: 18-08-2025 Page 1 of 2 Company Name: VITA ELECTRONICS CO LTD Address:

City:

Country:

5th FI 103 Chou Tze St Neihu District Taipei Taiwan To: Kiwa Netherlands B.V., Dept. FCC TCB Wilmersdorf 50 7327 AC Apeldoorn The Netherlands Subject: Request for confidentiality FCC ID: 2AVEACE-P21-7005 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below):

Internal Photos Users Manual Test Set-up Photos External Photos Justification:

Date: 06/16/2026 Name and signature of applicant: Jack Tseng Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

The planned date should state in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Kiwa NL B.V. at least 7 days before date of actual marketing or before expiration of the STC period FCC, Request for non-disclosure RF_501, Issue 12 Date: 18-08-2025 Page 2 of 2 Revision Record Sheet:

Revision Section number Page number Date Remark(s) issued by History sheet added Corrected date and page# WJJ Kiwa logo change AG AG 10 11 12 1 1 & 2 all 02-01-2023 23-06-2023 18-08-2025 Issued/modified by Function Revision Date

: Axel Gase

: Manager Quality Assurance

: 12

: 18-08-2025 Verified by Function Date

: Willem Jan Jong

: Team Lead

: 18-08-2025 Released by Function Date of release:

: Axel Gase

: Manager Quality Assurance

: 18-08-2025

RF_160_06 Declaration of Authorisation Date of issue 13-08-2025

(On manufacturers company letter heading) Declaration of Authorization We Name:

Address:

City:

Country:

Declare that:

VITA ELECTRONICS CO LTD 5th FI 103 Chou Tze St Neihu District Taipei. Taiwan. Name Representative of agent:

Agent Company name:

Address:

City:

Country Jack Chang. (1) T V S D Asia Ltd., Taiwan Branch. No.31, Dinghu Rd.,.. Taoyuan City.. Taiwan (R.O.C.). is authorized to apply for Certification of the following product(s):

Product description: Monitor. Type designation: CE-P21E-B / CE-P21XXXXXXXXXX. Trademark:

Validity/ expiry date clintonelectronics . on our behalf. Date:

City:

Name:

06/16/2026.. Taipei.. Jack Tseng.. (2) Function:

Electrical Safety Engineer. Signature:

. Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent. Revision Record Sheet:

Revision Section number 05 06 Page number Date Remark(s) issued by 1 all 02-01-2023 13-08-2025 History sheet added Kiwa logo change AG AG Issued/modified by Function Revision Date

: Axel Gase

: Manager Quality Assurance

: 06

: 13-08-2025 Verified by Function Date

: Willem Jan Jong

: Team Lead

: 13-08-2025 Released by Function Date of release:

: Axel Gase

: Manager Quality Assurance

: 13-08-2025

Page 4 of 2 17-07-2025 Agent letter FCC attestation statement Kiwa RF_753, Issue 4

[PLACE ON APPLICANT/COMPANY LETTERHEAD]

U.S. Agent Designation for Service of Process

(Applicant and U.S. Agent are Separate Parties) TO:

Kiwa Nederland B.V. Wilmersdorf 50 7327 AC Apeldoorn Postbus 137 7300 AC Apeldoom Netherlands ATTENTION: FCC Certification Section 2.911(d)(7) Information Designated U.S. Agent Company name: | Clinton Electronics Corp. |

FRN: 10 digit | 0038369708 number:

The US Agent does not have a FRN because this person does not do business with the FCC Gary Clinton Contact person name:

Street address: 6701 Clinton Road, Loves Park, ILLINOIS 61111, USA ZIP/City/State 61111 Telephone number: (815) 633-1444 garyclinton@

Signature: Lo3 1 Date:

This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-

related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: VITA ELECTRONICS CO LTD FCC ID: DAVEACE-P21-7005 es 0029052990 Contact person name: Jack Tseng _ Street address: 5th Fl 103 Chou Tze St Neihu Disirict _ ZIP/City/State/Count 114, Taipei, Taiwan {

02-26595977 Email address: [email protected] Signature: a a Date: 03/13/2026 i

, Lead te A ait th