FCC ID: 2AQK5-GIMBAL220 3-Axis Stabilized Handheld Gimbal for Camera

FCC regulatory conformance:

IC regulatory conformance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help This device complies with CAN ICES-3 (B)/NMB-3(B). This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la norme CAN ICES-3 (B)/NMB-3 (B). Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 10 mm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites dexposition aux rayonnements de la IC tablies pour unenvironnement non contr. Cet quipement doit tre install et fonctionner au moins 10mm de distance dun radiateur ou de votre corps. RF Exposure NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body, and with minimum distance of mm between the antenna and your handle. This transmitter must This transmitter must any other antenna or transmitter. not be co-located or operating in conjunction with 10

Label:

Product name: 3-Axis Stabilized Handheld Gimbal for Camera Vitec Imaging Solutions Spa ModelMVG220FF FCC ID: 2AQK5-GIMBAL220 IC: 24113-GIMBAL220 Input: 5V Location:

2.0A

Date: 20 July 2020 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

The Vitec Imaging Solutions Spa __, the undersigned, hereby authorizes Mr. Wu Xuewen from Shenzhen BALUN Technology Co., Ltd., to act on the behalf of the Vitec Imaging Solutions Spa solely in matters relating to the application for an FCC equipment authorization for FCC ID:

2AQK5-GIMBAL220 including the signing of documents in connection with this Application. Necessary acts carried out by Shenzhen BALUN Technology Co., Ltd. in connection with the Application shall have the same effect as acts of the Vitec Imaging Solutions Spa The Vitec Imaging Solutions Spa ___ also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. Section 862. Yours Sincerely, hoe Pha Roc Zhuang

VITEC IMAGING SOLUTIONS SPA Date: 20 July 2020 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: VITEC IMAGING SOLUTIONS SPA FCC ID: 2AQK5-GIMBAL220 FCC Certification Confidentiality Request Gentlemen:

This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. VITEC IMAGING SOLUTIONS SPA requests that the following documents regarding this submission for FCC ID: 2AQK5-GIMBAL220 be kept confidential:

Exhibit Type File Name Block Diagram Block Diagram.pdf Schematics Schematics.pdf Operational Description | Operational Description.pdf And below exhibit kept short-term confidential (180 days):

External photos External photos.pdf Test setup photos test photo.pdf Internal photos Internal photos. pdf User manual User manual.pdf Those documents contain detailed system and equipment description and related information about the product which VITEC IMAGING SOLUTIONS SPA considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, VITEC IMAGING SOLUTIONS SPA considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours Sincerely, k of. Dhe oc Zhuang