FCC ID: 2AU3Z-VWP Vivi Wireless Presentation

Vivi Instructions Installing the Box Skip to end of metadataGo to start of metadata To install the Box, you will need:

1. An active network port on your local network. 2. A Display which can be connected using a HDMI cable. 3. A power outlet. These all need to be close to each other at least for the initial setup. Once the Box is plugged in, it will boot up. Make sure the other connections are in place first. Depending on the setup of your local network, additional network settings may be needed before the Box can be fully activated. Antenna On Wi-Fi models only, connect the antenna to the back of the Box. Ethernet Connect the ethernet cable from the Box to your network. Make sure both ends of the network cable are plugged in, and that the corresponding network port is patched at the switch. If you need to register the MAC address of the Box to gain access to the local network, it is written on the side of the Box. The text will look like "D063B401C7F9" and corresponds to a MAC address of d0:63:b4:01:c7:f9. On Wi-Fi models, the network settings of the Box can be updated to use Wi-Fi later, but an ethernet connection is needed the first time around so that the Box can be activated. HDMI Connect the HDMI cable from your Display device to the Vivi Box. The HDMI cable can be connected to a VGA Display via a HDMI to VGA convertor or a HDMI to DVI convertor. However, this will only transmit video, and no audio. Human Interface Device (HID) compliant touch screens can also be used and can be connected via the USB connection. When initially setting up the device, it is best if a HDMI-capable Display device is used to simplify any troubleshooting that is required. USB connections The Vivi Box has two USB connections. They can be used for the following:

1. Connecting a USB audio device. 2. Connecting a HID compliant touch screen. 3. Performing a factory reset of the Box via a USB drive. Factory resets require the assistance of the Vivi Support team. AC Power / Power over Ethernet Once the Box is plugged in, it will boot up. Make sure all of the other connections are in place first. There are two options for powering the Vivi Box. Power can be provided by the AC power adapter (12V 1.5A DC). Power can also be provided by the Power over Ethernet (PoE) splitter. One will have been provided with the Box, based on your order. If the Box will later be configured to use Wi-Fi access to connect to the local network, then the AC adapter must be used. To use the PoE splitter, disconnect the ethernet cable from the Box, and connect both the ethernet connection and the power connector from the PoE splitter into the Box. The ethernet cable connect to the other end of the PoE splitter. Please note: Not all networks can provide power via the network or are configured to do so as standard. If the power is working, the red light (next to the power connection on the Box) will turn on. Boot up and Box activation When you first plug in a new Box, it may take a few minutes to self-extract its operating system and get itself ready for use this only happens the first time. At this point you should see a red light on the Box. After a few start up steps, the Vivi logo and either the Box name or a room name will appear on the Display. The Display may flicker for a few seconds while the device installs and activates. When the device has installed and is ready to go you should see something like this:

If the Vivi Box has been unable to activate itself, the following message will be displayed:

If you see this message on start-up, additional network configuration updates will be required. Add the required firewall exceptions and open the required internal network ports. Once they are in place, disconnect and reconnect the power so that the Box can reboot and run through the activation process again. FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna. connected. Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AU3Z-VWP Label and Location Model: VWP-200-16 FCCID: 2AU3Z-VWP Vivi Size: L: 4.0cm*W: 4.0cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2019/12/18 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 22AU3Z-VWP For the product stated above, we request that the following information be held confidential;

Model name VWP-200-16 Exhibits Long-Term Short-Term Short-Term Confidentiality Confidentiality Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Ian Shrimpton Name:

Company: Vivi International Pty Ltd Address:

Phone:

Fax:

E-Mail:

9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia

+61 1300 920 555

+61 1300 920 555 ian@vivi.io

Vivi International Pty Ltd 9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia Tel: +61 1300 920 555 E-mail: ian@vivi.io Date: Dec. 18, 2019 FCC ID: 2AU3Z-VWP Model Number: VWP-200-16 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Vivi International Pty Ltd declare that this EUT (2AU3Z-VWP) doesnt have Ad Hoc mode function onnon-US/Canada frequencies. Inaddition.The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name:

Company:

Address:

Phone:

Fax:

E-Mail:

Ian Shrimpton Vivi International Pty Ltd 9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia

+61 1300 920 555

+61 1300 920 555 ian@vivi.io

Vivi International Pty Ltd 9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia Tel: +61 1300 920 555 E-mail: ian@vivi.io Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

12/18/2019 We, Vivi International Pty Ltd the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AU3Z-

VWP including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Ian Shrimpton Name:

Company: Vivi International Pty Ltd Address:

Phone:

Fax:

E-Mail:

9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia

+61 1300 920 555

+61 1300 920 555 ian@vivi.io

Vivi International Pty Ltd 9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia Tel: +61 1300 920 555 E-mail: ian@vivi.io UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID2AU3Z-VWP

(1) DFS Device:

Master N/A Client with Radar detection capability Client without radar detection capability,

(2) Active / Passive Scanning ,adhoc mode access point capability Frequency Band

(MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning

(where the device is can listen only with no Ad Hoc Mode Capability Access point Capability 5745-5825 5755-5795 5775-5775 5180-5240 5190-5230 5210-5210 5260-5320 5270-5310 5290-5290 5500-5700 5510-5670 5530-5610 Yes No Yes No Yes No Yes No Yes No Yes No N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A probes) Yes No Yes No Yes No Yes No Yes No Yes No N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Yes No Yes No Yes No Yes No Yes No Yes No N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Yes No Yes No Yes No Yes No Yes No Yes No N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

(3) Country code selection ability Yes If yes, pls explain how it was implemented:

No

(4) Meet 15.202 requirement Yes No pls check below :

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non- DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Does not apply Sincerely, Ian Shrimpton Name:

Company: Vivi International Pty Ltd Address:

Phone:

Fax:

E-Mail:

9 Oxford Street, South Yarra, Melbourne VIC 3141, Australia

+61 1300 920 555

+61 1300 920 555 ian@vivi.io