FCC ID: Q5530SCA Card Reader

ViVOtech, Inc. Report # R0311052.doc APPENDIX E - USERS MANUAL Page 28 of 29 pay TM 3000 USER GUIDE FCC Regulatory Compliance: Notices Class B Equipment: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. WARNING:

1.The ViVOpay hardware or software can not be replaced or modified by any third party other than VIVOtech. Changes or modifications not expressly approved by ViVOtech could void the user's authority to operate the equipment. 2. Minimum separation distance between 2 ViVOpay devices should be at least 2 feet. 3.The device should be mounted and seated on a non metal surface and be at least 6 inches far from any metal surface. Version 1.1 January 2004 Copyright 2004 ViVOtech, Inc. TM Quicker than cash, Safer than checks SM www.vivotech.com ViVOtech Corporate Headquarters 451 El Camino Real, Santa Clara, CA 95050. Phone: (408) 248 7001 Quicker than cash, Safer than checks SM TM ViVOpay 3000 USER GUIDE LEDs and Sound The merchant operation of the ViVOpay 3000 is very simple and almost entirely automated. Once installed, the clerk's role on the operation of the system is simply to guide new customers to hold their cell phones or plastic cards enabled with a contactless RF chip in front of the Reader Module. The information is automatically transferred to POS system and processed in the same way a standard magnetic card would be. How it Works Contactless devices as cell phones and plastic cards are enabled with RF tags that securely release the payment information to the ViVOpay terminals without the need of physical contact with the Point of Sale terminal using contactless technology.The ViVOpay is constantly emitting a magnetic field, when it detects an RF tag in the field it communicates with it and retrieves the payment information. The card information is then transmitted to the POS device via the Dynamic StripTM or direct serial connection. Typical Usage 1. The customer approaches the clerk with one or more items to purchase. The clerk enters the items into the cash register, and once done, asks the consumer for the form of payment and mentions the contactless payment option by pointing to the ViVOpay. 2. The consumer pulls it's contactless cell phone or plastic card and holds it in front of the ViVOpay. 3. The ViVOpay quickly reads the information from the card through RF technology - no physical contact is necessary. In a fraction of a second the reader validates the card, and secures the transaction.

(As the reader is facing the customer and probably the clerk won't be seeing the LEDs, a beep will let the clerk know that the read was successful). 4. ViVOpay 3000 automatically sends the information to the POS, which processes it as a conventional magnetic stripe card, though with increased security.

(Besides mentioning contactless payments and pointing to the ViVOpay unit no intervention from the clerk is necessary during the entire procedure). 5. The POS terminal prints the receipt, which the clerk gives to the consumer for signature as with any other purchase. Quicker than cash, Safer than checks www.vivotech.com TM SM Consumers just need to hold their Paypass devices in front of the ViVOpay The ViVOpay is equipped with 4 LEDs on it's translucent cover as well as sound interface to provide consumers feedback on the read process. Upon a successful transaction all 4 LEDs will turn on and a beep will sound to let the customer know that the transaction is completed. Idle: Just first LED is ON Read SUCCESS: all LEDs will be turned on while the module emits a sound acknowledging the success. Read ERROR: If there's an error while reading a card the LEDs will not turn On and no sound will be emitted ViVOtech Corporate Headquarters 451 El Camino Real, Santa Clara, CA 95050. Phone: (408) 248 7001

A ViVOpay 3000 Installation Guide for VeriFone Ruby May 2004 Version 1.0 ViVOtech, Inc. 451 El Camino Real Santa Clara, CA 95050 Ph: 408.248.7001, ext.105 Email: info@ViVOtech.com www.vivotech.com Part number: 600-1030-00 Copyright 2004, ViVOtech, Inc. All rights reserved. ViVOtech, Inc. 451 El Camino Real Santa Clara, CA 95050 Phone: (408) 248-7001 Written and designed at ViVOtech, Inc. This paper, as well as the software and hardware described in it, is furnished under license and may be used or copied online in accordance with the terms of such license. The content of this paper is furnished for information use only, is subject to change without notice, and should not be construed as a commitment by ViVOtech, Inc. ViVOtech, Inc assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Except as permitted by such license, no part of this publication may be reproduced or transmitted by electronic, mechanical, recording, or otherwise, or translated into any language form without the express written consent of ViVOtech, Inc. ViVOtech, ViVOwallet, ViVOcard, ViVOpay, ViVOplatform Dynamic Strip, ViVOsmartcable and ViVOgiftcard are trademarks or registered trademarks of ViVOtech, Inc. All other products or name brands are trademarks of their respective holders. May 2004 VeriFone Ruby Installation Guide 1 The ViVOpay 3000 patent-pending Dynamic Strip technology enables contactless payments without hardware or software changes to existing POS devices at minimum cost. This document assumes that installers are familiar with their host POS system. NOTE: It is highly recommended that you review the procedure at least once prior to exposing the adhesive mounting tapes. Obtain the necessary components by removing the following ViVOtech products from the shipping carton:

ViVOpay power adapter Dynamic Strip Alcohol Wipe Cable support clip ViVOpay 3000 Obtain the following products from your work area:

Your POS terminal, turned on Ruby, powered up Serial link cable Pencil The Plug-and-Play application is installed as follows:

1. Clean the terminal Use the alcohol wipe to clean the POS terminal case. Wipe the top and side areas around the magnetic strip where the cable clips will be attached. CAUTION: Do not push the pad into the strip!

3 VeriFone Ruby Installation Guide V 1.0 It is important that these areas be clean of any oily or greasy residue that will interfere with the adhesive mounting tapes. Allow the terminal to air dry. 2. Power up the ViVOpay unit in strip test mode Connect the Dynamic Strip cable to the back of the ViVOpay unit. Connect the AC adapter into an AC power outlet. Simultaneously press the button at the rear of the reader with the pencil and insert the power connector from the AC adapter into the socket on the back of the ViVOpay unit. Continue to hold the button for five seconds until a continuous beeping is audible. The ViVOtech unit is now in strip test mode. In the test mode, the ViVOpay unit's LED will flash approximately every two seconds to indicate the strip test mode. The ViVOpay unit will automatically transmit factory-installed test data to the POS terminal strip to allow the installer to correctly position the strip on the magnetic head. WARNING: Do not disassemble the AC adapters. Only qualified technicians may service the adapters. The AC adapters are intended for indoor use only; do not expose to rain or snow. Do not immerse the AC adapters or the terminal in fluid. 3. Initiate the magnetic strip test on your POS terminal It is necessary to set the POS terminal in the Card Reader Diagnostics (test) Mode in order to precisely position the Strip. a. Press the "Function" and "7" keys simultaneously to exit the credit card payment application. Enter the password 1 <alpha> <alpha> 66831. 4 VeriFone Ruby Installation Guide V 1.0 b. While in the card-reader test mode, the terminal will display the track data being transmitted from the magnetic card or Dynamic Strip being used on your terminal. NOTE: If the Ruby does not have an application loaded, press 4 twice. c. Plug the power cables into the power ports on the Ruby device and the printer. d. Connect the printer to the Ruby. The coiled cable plugs into the printer's COM4 port on the back of the Ruby. e. Plug power supply cable into an AC outlet. f. Wait until the Ruby boots up. It will take a few minutes. g. When the Ruby prompts for a cashier number, enter 1 and press enter. h. For the password, enter 123 and press enter. i. The Ruby will display 'Ready for sale'. You can now process transactions. j. Key in a dollar amount (e.g., 100 for $1.00). Press the FUEL key (located in the top row of keys near the right). If you enter a value of $20.00 or greater, the device will prompt for an Air Miles card later in the transaction. k. Press enter to select the BRONZE fuel type. l. Enter a pump number when prompted to (any number) and press enter. A non-fuel sale product has is also available. At the 'Ready for sale'

prompt, key in 10 and press enter. You can repeat to add more items. m. Press the TOTAL key. n. Press the CREDIT key. You will then be prompted to swipe a credit /debit card. 4. Position the Dynamic Strip and mark the correct position Carefully insert the strip into the card-reader slot from the top of the terminal. Move the strip towards the center of the card-

reader in small increments while observing changes on the display as the ViVOpay unit continuously sends test data. 5 VeriFone Ruby Installation Guide V 1.0 When the Strip is correctly positioned, the screen on your POS terminal will display data for Tracks 1 (top) and 2 (bottom). Mark each side of the Dynamic Strip with a pencil. You now have a range where the strip transmits data correctly. NOTE: There may be multiple ranges where data is displayed correctly on the screen. If this happens, select the middle range. If Track 1 data and Track 2 data display in different locations, select the location that displays Track 2 data. Track 2 is the bottom row on the display. CAUTION: Once the Strip is installed, it cannot be removed without damaging the Strip. A new Strip will be required. 5. Remove the protective covering from adhesive tab and affix Strip firmly in place Remove the protective covering from the plastic adhesive mounting tabs of the Strip. 6 VeriFone Ruby Installation Guide V 1.0 Carefully position the strip into the slot exactly in the middle range of the two pencil marks. When the strip is in position where the POS readings are successfully displayed, press the top of the strip against the terminal to ensure the adhesive holds tightly. 6. Verify the installation and terminate the test The Strip is correctly installed if your POS terminal continues to display successful readings after the Strip has been affixed. Re-start the ViVOpay by removing and reinserting the power plug. Swipe a standard credit or debit card backwards (so that no transaction occurs) through the card swipe slot to make sure there is no excessive friction. 7. Install the cable support clips To attach the support clip to the Strip cable, remove the protective covering from the adhesive on the bottom of the clip. 7 VeriFone Ruby Installation Guide V 1.0 Press the Strip cable into the clip. Position the clip on the right side of the POS terminal to guide the cable to the back of the POS terminal. Press the clip down to adhere it in place ensuring the cable is routed away from areas where it may be snagged. Installation is now complete. 8 VeriFone Ruby Installation Guide V 1.0