FCC ID: EZSR6867T R6867T

R6867T Replacement Digital Control Center Product Description Remote Pairing The R6867T control center is compatible with the following modules:

DS4 and DS4+. Mounting the Control Center Note Once this replacement control center has been installed, all remote controls must be paired with your system. See Remote Pairing for details and follow the instructions for your remote control type. The control centers position should be discussed with the vehicle owner prior to installation since the antenna, with built-in status LED and Valet/

Program, must be visible/accessible to the customer. The best position to locate the control center is centered high on the front windshield. It can be mounted vertically or horizontally relative to the windshield. Metallic window tint can also affect range negatively, so this should be a consideration when determining the mounting location. After you determine the best mounting location, follow these steps:

Clean the mounting area with a quality glass cleaner or alcohol to remove any dirt or residue. Plug the cable into the control center. Mount the control center with double-sided tape. Route the cable down the window pillar to the control module and plug the cable in the control module. CABLE CONTROL CENTER Prepare the vehicle system to be Paired with a new remote 1. 2. 3. Within 5 seconds press and release the Control button on the Control Open at least one vehicle door. Turn the key to the ON position. Center one time. 4. Within 5 seconds, press and hold the Control button on the Control Center. The status LED begins ashing in single ash sequence and the siren/horn sounds once to conrm the system is ready for remote pairing. Release the button. Locate your remote control model below and follow the instructions. 5. System Pairing will exit if:

The ignition is turned off The open door is closed 60 seconds lapses with no actions Note: Make sure the remote to be paired with the system is set for the de-

sired Car 1 or Car 2 operation. LCD Remote Control:

1. Press and hold the AUX button for 8 seconds, the remote beeps once, AUX Main Menu is displayed. Release the button. AUX AUX AUX 2. 3. Press the AUX or Press and hold the lease the Press the buttons until Pair is displayed. button until the remote beeps 3 times then re-

button. The remote is now ready to pair with the system. button. 4. 5. Wait several seconds for feedback as the remote generates a security encryption and sends it to the Control Center. If pairing is successful the siren/horn sounds and the remote emits several tones. The screen displays if the Pairing is successful or failed with corresponding text. If pairing fails repeat step 4. AUX To exit pairing mode on the remote:

Press and release the Wait 30 seconds without pressing a command button on the remote. button. Responder LED or Companion Remote Control:

1. A U X AUX button for 8 seconds. The transmit LED will come AUX button. until the transmit LED ashes 3 times then AUX 2. Press and hold the on solid. Release the Press and hold the comes on solid. Press the button. AUX 3. 4. Wait several seconds for feedback as the remote generates a security encryption and sends it to the Control Center. If pairing is successful the siren/horn sounds and the 2-way remote emits several tones (the companion remote does not generate tones). If pairing is not suc-

cessful press and release the 2 and 3. button once and then repeat steps AUX CONTROL MODULE 2022 VoxxElectronics, All rights reserved.

1 To exit pairing mode on the remote:

AUX button once, then press and hold until the Press and release the transmit LED shuts off. Wait 30 seconds without pressing a command button on the remote control. NR6867T--2022-07-11 GOVERNMENT REGULATIONS This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more from the persons body. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes

(1) cet appareil ne doit pas provoquer d'interfrences et

(2) cet appareil doit accepter toute interfrence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil. Health Canada RF Exposure Warning:

This device complies with Health Canadas Safety Code. The installer of this device should ensure that RF radiation is not emitted in excess of the Heath Canadas requirement. The device must maintain a separation distance of 20cm or more from the persons body. Information can be obtained at:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-eng.php Lignes Directrices de Sant Canada sur lexposition aux radiofrquences:

Cet appareil est conforme avec Sant Canada Code de scurit 6. Le programme dinstallation de cet appareil doit sassurer que les rayonnements RF nest pas mis au-del des limites tablies par Sant Canada. Lemplacement de l'appareil doit se situer une distance de 20cm ou plus par rapport au corps de la personne, lexception des mains et des poignets. Les informations peuvent tre obtenues ladresse Internet suivante:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-fra.php 2022 VoxxElectronics, All rights reserved. 2 NR6867T--2022-07-11 LIMITED ONE YEAR CONSUMER WARRANTY For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (DIRECTED) prom -ises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumers name, address, telephone number, the authorized licensed dealers name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALERS PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTEDS OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTEDs website at: www.directed.com 2022 VoxxElectronics, All rights reserved. 3 NR6867T--2022-07-11

Voxx Electronics Corporation DATE:2022-07-19 Communications Federal Authorization 7345 Oakland Columbia,

& Evaluation Mills Road Maryland 21046 Commission Division Authorjty to Act asAgent ppoint Jianyan Testing Group Shenzhen Co., On our behalf, I a Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community,Xinqiao Street, Bao'an Shenzhen, Guangdong,People's Republic of China., to act as our agent in the application for equip or system f sought. Communications Commission's regulations will have affixed to it a l identical to that submitted for approval with this application I also certify that each unit manufactured, imported or marketed, as defined in the or which equipment certification is ertify that submitted documents prop erly describe the device preparation of this ment certification. I c

, Buildin Ltd.; No.101 District, Federal abel g 8,

. where our authorized For instances that all responsibility Electronics for complying agent signs the application for certification with the terms and conditions on our behalf, for certification, as specified by Voxx I acknowledge Corporation, still reside s with 310 ALDER RD, DOVER D E 19904 USA Dated 2022-07-19 By:

fof.ure Title:

Joseph A. Santavicca Printed On behalf of: Voxx Electronics Corporation Telephone:

(1) 248 307-3830

Voxx Electronics Corporation DATE :2022-07-19 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID:EZSR6867T Product Name: R6867T Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Schematics Bill Of Material (BOM) Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2022-07-19 By: = Joseph A. Santavicca Signature Printed Title: SVP of Engineerin On behalf of : Voxx Electronics Corporation Telephone: (1) 248 307-3830