FCC ID: G2R-5601 SANDY SNACKS-A-LOT

Instruction Manual Sandy Snacks-a-LotTM FPO INTRODUCTION Thank you for purchasing Sandy Snacks-a-LotTM Pet, feed and interact with Sandy to hear fun reactions of 8 different play pieces and watch her react to different foods, flavors and sensations with fun phrases, songs, sound effects and color changing lights. Head Touch Sensor Play Piece Recognize Sensor Mouth Open Sensor Moody Light FPO OFF/Low/High Volume Switch Learning Button Play Pieces Storage Cover Song Button 8 Play Pieces 2 INCLUDED IN THIS PACKAGE One Sandy Snacks-a-LotTM 8 Food Play Pieces One Parents Guide WARNING All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your childs safety. NOTE: Please save this Instruction Manual as it contains important information. ATTENTION Pour la scurit de votre enfant, dbarrassez-vous de tous les produits demballage tels que rubans adhsifs, feuilles de plastique, attaches, tiquettes, cordons et vis demballage. Ils ne font pas partie du jouet. NOTE : Il est conseill de sauvegarder ce manuel dutilisation car il comporte des informations importantes. Unlock the Packaging Lock Rotate the packaging lock counterclockwise 90 degrees. Pull out the packaging lock and discard. 3 ACTIVATING NORMAL PLAY MODE The first time the Sandy Snacks-a-LotTM is used, you will need to exit Try-Me mode and activate Normal Play mode. 1. Slide the OFF/Low/High switch to turn the unit on. 2. Except for the green pepper, feed Sandy other food pieces. You will hear three du sounds as an indication that the normal mode is activated. You will hear three du sounds indicating that the unit is in Normal Play mode. GETTING STARTED Battery Removal and Installation 1. Make sure the unit is turned OFF. 2. Find the battery cover located at the bottom of Sandy and use a screwdriver to loosen the screw and open the battery cover 3. Remove old batteries by pulling up on one end of each battery. Install 4 new AA batteries following the diagram inside the battery box. 4. 5. Replace the battery cover and tighten the screw to secure. IMPORTANT: BATTERY INFORMATION Insert batteries with the correct polarity (+ and -). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable Only batteries of the same or equivalent type as recommended batteries. are to be used. 4 Do not short-circuit the supply terminals. Remove batteries during long periods of non-use. Remove exhausted batteries from the toy. Dispose of batteries safely. Do not dispose of batteries in fire. RECHARGEABLE BATTERIES Remove rechargeable batteries (if removable) from the toy Rechargeable batteries are only to be charged under adult before charging. supervision. Do not charge non-rechargeable batteries. WARNING:

Adult assembly required for battery installation. Keep batteries out of reach of children. ATTENTION :

Les piles ou accumulateurs doivent tre installs par un adulte. Tenir les piles ou accumulateurs hors de porte des enfants. PRODUCT FEATURES 1. OFF/Low/High Volume Switch Slide the OFF/Low/High Volume Switch to turn on the unit and choose low and high volume. 5 2. Head Touch Sensor Touch the head ( the location shown in the picture) to hear different fun sounds. 3. Learning Button Press the Learning Button to hear interactive phrases about colors and food. 4. Song Button Press the Song Button to hear fun songs. 5. 8 Play Pieces Put a play piece in front of Sandys mouth to make Sandys mouth open. Then you can place the play piece on its tongue or directly in its mouth to see how Sandy reacts. 6 Note: Please only feed Sandy the 8 play pieces provided by this toy, others are not recommended. 6. Mouth Open Sensor The sensor is located the lower part of Sandys mouth. Put anything in front of the sensor to make Sandy open its mouth. 7. Play Piece Recognize Sensor When a play piece is in Sandys mouth, she can recognize which food she is eating. Lets see how she reacts. Sandy will respond to the play piece and tell you how it tastes. 8. Play Pieces Storage Open the storage cover for the play pieces located at Sandys tail and place the play pieces into the compartment. 7 9. Moody Light Different lights color reflects Sandys feeling. It will also light up when Sandy sings. 10. How to open and close the storage To open the storage, hold Sandys tail with one hand and pull the locking buckle upwards at the same time, the storage will fall off itself. To close the storage, put and align the storage cover with the right place, then press the cover, you will hear a click sound. 9. Automatic Shut-Off To preserve battery life, the Sandy Snacks-a-LotTM will shut off automatically after several minutes without input. The unit can be turned on again by sliding the OFF/Low/High Switch. Sandys belly will flash in red three times and then automatically turn off when the batteries are very low. Note:

1. Opening and closing Sandys mouth with hands forcibly are not recommended. 2. Do not grab Sandys tongue when it sticks into the mouth. 3. Do not put the toy under water. 8 ACTIVITIES 1. Press the Learning Button to learn color facts or hear Sandy talk about food. 2. Press the Song Button to hear Sandys sings, with moody light. 3. Touch Sandys head to comfort her and show her affection. When Sandy is singing, touch her head will hear fun sounds jammed in the song. 4. Feed Sandy with one of the 8 Play Pieces to see how she reacts. Please be mindful! Sandy will feel full (and hiccup) for yummy food or get angry (and give you a fart) for disliked food if you feed it too much!

Note: Please only feed Sandy the 8 play pieces provided by the toy, others are not recommended. SONG LYRICS Song 1 My gills are really cool and people love my smiling face. They help me breathe in water, as I move from place to place. Song 2 Sour and spicy, cold and sweet. So many things to try, so many things to eat. 9 Song 3 I am a walking fish. Axolotl is my name. I swim or walk on land!

Would you like to play a game?

Song 4 I love food and I am hungry. Im ready for a snack. SFX - Bleah!

What is that you fed me?

You better take it back!

Song 5 Sleeping, playing, hiding, I come out at night. My home is in the rocks, hiding from the light. Song 6 I love all the colors in my yummy food. Red strawberries, yellow lemons. Pink ice cream is tasty too. Song 7 Humming to the tune of the song If youre happy and you know it Song 8 Humming to the tune of the song Bingo Song 9 Humming to the tune of the song Alouette Song 10 Humming to the tune of the song Entertainer 10 CARE & MAINTENANCE 1. Keep the unit clean by wiping it with a slightly damp cloth. 2. Keep the unit out of direct sunlight and away from any direct 3. Remove the batteries if the unit will not be used for an extended 4. Do not drop the unit on hard surfaces or expose the unit to heat sources. period of time. moisture or water. TROUBLESHOOTING If for some reason the unit stops working or malfunctions, please follow these steps:

1. Turn the unit Off. 2. 3. Let the unit stand for a few minutes, then replace the batteries. 4. Turn the unit On. The unit should now be ready to play again. If the unit still does not work, install a new set of new batteries. 5. Interrupt the power supply by removing the batteries. IMPORTANT NOTE:

If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S., 1-877-352-8697 in Canada, or by going to our website vtechkids.com and filling out our Contact Us form located under the Customer Support link. Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to contact us with any problems and/or suggestions you might have. A service representative will be happy to help you. 11 Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 12 Suppliers Declaration of Conformity 47 CFR 2.1077 Compliance Information Trade Name:

Model:

Product Name:

Responsible Party:

Address:

VTech 5601 Marble Rush Corkscrew Rush Set VTech Electronics North America, L.L.C. 1156 W. Shure Drive, Suite 200, Arlington Heights, IL 60004 vtechkids.com Website:

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-003(B)/NMB-003(B) 13 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 14 Visit our website for more information about our products, downloads, resources and more. vtechkids.com vtechkids.ca Read our complete warranty policy online at vtechkids.com/warranty vtechkids.ca/warranty 2024 VTech. All rights reserved. IM-560100-000 Version:0

4X1.5V AA LR6 / AM-3 1

. 5 V AA/LR6/ A M - 3 36.5 88.4 62.7 30-060461-X00 30-060458-X00 80.5

160.73 1

. 5 V AA/LR 6 / A M -3 53.7 24.8 30-060457-X00 96.6 51.9 30-060473-X00 54

VTech Electronics Limited DATE : 2024.3.18 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, | appoint EST Technology Co., Ltd. Address: Chilingxian:

China (Name of Agent company name and address) to act

@s Our agent in the preparation of this application for equipment certification. 1 certify that Houjie, Dongguan, Guangdon:

manufactured, imported or marketed, as ns regulations will have affixed to it a iS application. For instances where our certification is sought. | also certify that each u defined in the Federal Communications Com label identical to that submitted for approval authorized agent signs the application for certification on ourbeh 1 ackno: ge that all responsibility for complying with the terms and conditionsfor certification, still resides with_ MTech Electronics Limited Address: 23/F, Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road Tai Po, Hong Kong (Applicant Name and address)

<Signature>

Name: Antony Wong Ate a Title: Senior Manager Company: VTech Electronics Limited

DATE : 2024.3.18 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: G2R-5601 Product Name: SANDY SNACKS-A-LOT Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ...)

- Schematics

* Block diagram

* Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature>

Name: Antony Vong ( Ver Title: Senior Manager Company: VTech Electronics fimitea CY

With Applicant Company Letterhead Attestation Statements Not Covered Entity Applicant & Not Covered Equipment Te: Federal Communications Commission Date: 07-02-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)@ & (ii) & Section 2.911(d)(7) filing FCC ID: G2R-5601

'g of the application, the quipment.

[VTech Electronics Limited] (the applicant) certifies that, as of the date of the applicant is not identified on the Covered List as an entity producing covered The equipment for which authorization is sought is not covered telecommunications equipment and video ance equipment produced by entities identified on the Commission's Covered List that prohibited from ng an equipment authorization pursuant to section 2.903 of the FCC rules.

[VTech Electronics Limited] (the applicant") as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicant's agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. FCG US Agent Company Name: VTech Electronics North America, L.L.C. Contact Name: Paul Repak Address: 1156 W. Shure Drive., Suite 200, Arlington Heights, ILLINOIS 60004 Phone No-: 847-385-0811 Email Address: prepak@vtechkids.com FCC FRN: 0033426537 Sincerely yours, Applicant Signature Printed Name: Antony Wong Title: Senior Manager Email: antony_wong@vtech.com

VTech Electronics Limited I, the signer, They have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction. Item Name: SANDY SNACKS-A-LOT Model Number: 5601 Additional Model: 80-560100,80-560103,80-5601 04,80-560105,80-560122, 80-560123, 80-5601XX (XX=00~99) Note: XX is a variable, it can be 00-99, represents different languages or different colors. They have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction. FCC ID: G2R-S5601

<Signature>

Name: Antony Wong Chace Title: Senior Manager Company: VTech Electronics Limite

vtech VTech Electronics Lid. U.S. Agent Letter of Attestation To: Federal Communications Commission Date; Mar-1-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Attestation Statement Part 2.911(d}(7) filing FCC ID: G2R-5604 VTech Electronics Limited. (the applicant") certifies that, as of the date of the filing of the application, VTech Electronics, North America, L.L.C. ("the agent) is our designated U.S, agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process In the United States for no lass than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges It is our responsibility to inform the FCC whenever the agent Information changes, VTech Electronics, North America, L.L.C. (the agent") understand It Is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S, address and email address. APPLIGANT Company Name: VTech Electronics Limited. Contact Person: Antony Wong Address: 23F Tai Ping Industrial Center, Block 1, 57 Ting Kok Road,Tai Po,Hong Kong Tel: 26801233 Email: anton won vtech.com FCC FRN: 0032657439 U.S.A ent Company Name: VTech Electronics, North America, L.L.C, Contact Person: Paul Repak Address: 1156 W. Shure Drive., Suite 200, Arlington Heights, ILLINOIS 60004 Tel.: 847-385-0811 Email: prepak@vtechkids.com FCC FRN: 0033426537 Sincerely yours, ee The A licant The A ent Com an Name VTech Electronics Limited VTech Electronics, North America, L.L.C. Contact Person Anton Won Paul Re ak Signature Vow hep WA