FCC ID: EW780-0144-01 1.9GHz DECT Baby Monitor - Parent Unit

Before use 1. Place the baby unit at least 1 meter / 3 feet away from your baby. Overview At least 1 meter

(3 feet) Baby unit overview Whats in the box Install the battery as shown below. Users manual DM223/DM223-2 Safe & Sound Digital Audio Monitor BC Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. Register online to get an additional 3-month warranty!

Visit www.vtechphones.com. Registration Register your product online for enhanced warranty support. Product news Learn about the latest VTech products. 1 set for DM223;

2 sets for DM223-2 Install the battery The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only. NOTES Use only the battery supplied with this product. If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage. Without AC power charging, the battery gradually discharges, even when the parent unit is switched off. 7 8 9 m n Battery level indicator Light on when the battery is being charged. Light flashes when the battery is low and needs charging. Light off when no battery is installed. Press to increase the speaker volume. While in a menu, press to scroll up. VOL. SELECT While in a menu, press to choose an item, or save a setting.

(On/off) Press and hold to power on or off. While in a menu, press to return to idle screen. 10 11 TALK Press and hold to talk to the baby unit;

release to stop talking. While in a menu, press to return to idle screen. 12 Power jack 13 Belt clip 14 Battery compartment cover Parent unit overview a b c d e f g h i j k l 1 Microphone VOL. Speaker Press to decrease the speaker volume. While in a menu, press to scroll down. 4 MENU/

Press to enter the menu while idle. While in a menu, press to return to the previous screen. Press to return to idle screen. Visual sound indicator 2 3 5 The visual sound indicator has two functions. One is to show the sound level detected by the baby unit. The other one is to show the volume level during speaker volume setting. Sound level detected by the baby unit One to three green lights indicate a moderate sound level detected by the baby unit. Additional red lights indicate a higher sound level detected by the baby unit (e.g. baby crying loudly). Speaker volume level One to three green lights indicate Level 1 to Level 3 of the speaker volume setting. Additional red lights indicate Level 4 to Level 5 of the speaker volume setting. 6 LCD panel THIS SIDE UP CR0920

/

in China Fabriqu en chine INCINRER OU PERCER LES PILES. Made NE PAS DO NOT BURN OR PUNCTURE BATTERIES. WARNING BT183342/BT283342 (2.4V 400mAh Ni-MH) Battery Pack AVERTISSEMENT :

Bloc-pi les :

/

/

THIS SIDE UP / CE CT VERS LE HAUT NOTE Make sure the supplied rechargeable battery with the label THIS SIDE UP facing up.

/

in China Made Fabriqu INCINRER OU P NE PAS DO NOT BURN OR PUNCT WARNING AVERTISSEME BT183342/BT283342 (2.4V Battery Pack les :

Bloc-pi

/

/

THIS SIDE UP / CE Replace the battery To replace the battery, unplug the battery connector from the socket, and then pull the battery out of the battery compartment. Follow the steps above to install the battery. Parent unit display icons Connection status displays when strong signal strength is detected between the baby unit and the parent unit. displays when moderate signal strength is detected between the baby unit and the parent unit. displays when the weak signal strength is detected between the baby unit and the parent unit. flashes when the link between the baby unit and the parent unit is lost. Night light auto-on On when the night light auto-on feature is turned on. Sound alert Displays when the sound alert of the parent unit is turned on. Flashes when there are loud sounds detected from the baby unit and the parent unit is in mute. Vibration alert Displays when the vibration alert of the parent unit is turned on. Flashes when there are loud sounds detected from the baby unit. Mute Displays when the volume is turned off. Battery status animates when the battery is charging. displays solid when the battery is fully charged. flashes when the battery is charged with AC adaptor, or charging failure. flashes when the battery is in low level and needs charging. No battery icon displays when there is no battery installed. Connect and charge the battery NOTES Use only the parent unit power adapter or the baby unit power adapter supplied with this product. Make sure the electrical outlets are not controlled by wall switches. The parent unit power adapter and baby unit power adapter are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Make sure the parent unit, the baby unit and the power adapter cord are out of reach of children. Connect the baby monitor Charge the parent unit battery Once you have connected the parent unit or installed its battery, it powers on automatically. The battery icon indicates the battery status

(see the following table). NOTES The parent unit battery is fully charged after 11 hours of continuous charging. It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging. The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery. Battery status No battery is installed. The parent unit can be used only when it is connected to AC power. The battery has very little charge and may be used for only a short time. The battery is fully charged. Battery indicators The battery icon is off. LOW BATTERY and ash on the screen. The light flashes. The battery icon becomes solid

. Action Install the parent unit battery. Charge without interruption

(at least 30 minutes). Charge without interruption

(about 30 minutes). To keep the battery charged, connect it to AC power when not in use. Parent unit display screen messages CHECK BATT LINKED LOW BATTERY NOT LINKED PAGING The battery charging performance is abnormal, the light is off and the on the screen. icon flashes The link between the parent unit and the baby unit is established. The parent unit uses only the rechargeable battery pack and it needs to be recharged. The link between the parent unit and the baby unit is lost continuously for over 10 seconds. All idle parent units are being paged by the baby unit. SAVED Your selection has been saved. SEARCHING The parent unit is out of range of the baby unit, or the baby unit is out of power. TALK The parent unit is talking to the baby unit. TALKBACK The other parent unit is talking to the baby unit. Using the baby monitor Power on or off the baby unit Press and hold POWER to power on the baby unit. The power light turns on. Press and hold POWER again to power off the baby unit. The power light turns off. Power on or off the parent unit Press and hold unit. The screen turns on. Press and hold parent unit. The screen turns off. again to power off the to power on the parent NOTE The parent unit powers on automatically once it is connected to AC power or battery installed. The baby unit also powers on automatically once connected to AC power. Adjust the speaker volume for baby unit on the baby unit at or VOL. Press VOL. any time. Adjust the speaker volume for parent unit You can adjust the speaker volume from VOLUME 1 to VOLUME 5, or turn it off. The speaker volume is preset to VOLUME 3. when the parent or VOL. Press VOL. unit is not in use. When the speaker volume is set to off, the screen displays

. NOTE This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such. You may test the baby monitor before initial use, and at regular times thereafter. Place the parent unit and the baby unit in he same room to test the product. Test your audio monitor Speak towards the microphone of the baby unit. You will hear the sound at the parent unit, and see the visual sound indicators light up. LINKED LINKED TIP Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby unit. NOTES Make sure the baby unit is at least 1 meter (3 feet) away from the parent unit. If no connection can be established, the parent unit displays NOT LINKED and flashes. Positioning the baby monitor CAUTION Keep the baby unit out of the reach of the baby. Never place or mount the baby unit inside the babys crib or playpen. Do not expose the baby unit to extreme heat or direct sunlight. Adjust the sound sensitivity of the baby unit You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sound sensitivity is preset to LEVEL 5. Sound sensitivity table for reference Display Sensitivity Description Level 5 Level 4 Level 3 Level 2 Level 1 High sensitivity Low sensitivity High sensitivity level The parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your babys room. Medium high sensitivity level The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly. Medium sensitivity level The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Medium low sensitivity level The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Low sensitivity level The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds. 1. 2. 3. 4. Press MENU when the parent unit is not in use. Press SELECT. Press VOL. sensitivity level. Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. to choose the or VOL. a b c 1 2 3 4 5 6 7 8 2. Place the parent unit at least 1 meter /

3 feet away from the baby unit. At least 1 meter (3 feet) NOTE If you experience audio feedback on either the parent unit or baby unit, move the parent unit further away until there is no more audio feedback;

or press VOL. audio feedback sound. on the parent unit to lower the Operating range The operating range of the baby monitor is up to 300 meters (1,000 feet) outdoors or 50 meters

(160 feet) indoors. The actual operating range may vary depending on the environmental conditions, and other interferences such as walls, doors, and other obstructions. NOTE To enter the sensitivity menu of the parent unit, the baby unit must be turned on. Sound alert Sound alert feature works only when the parent unit is in mute. If you turn on the sound alert, the parent unit beeps when the baby unit detects sounds which light up four sound level indicators on the parent unit. When the sound alert of the parent unit is turned displays. The sound alert is preset to OFF. on, 1. or VOL. to choose Press MENU when the parent unit is not in use. Press VOL. SOUND ALERT, then press SELECT. Press VOL. OFF. Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. to choose ON or or VOL. NOTE The sound alert setting on each parent unit is independent. Vibration alert You can turn on the vibration alert so that the parent unit vibrates when the baby unit detects sounds which light up four sound level indicators on the parent unit. When the vibration alert of the parent unit is turned on, OFF. 1. displays. The vibration alert is preset to or VOL. Press MENU when the parent unit is not in use. Press VOL. to choose VIBE ALERT, then press SELECT. Press VOL. OFF. Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. to choose ON or or VOL. NOTES Each time you set the vibration alert to ON, the parent unit vibrates briefly after you press SELECT. The vibration alert setting on each parent unit is independent. 2. 3. 4. 2. 3. 4. d e f g h i j VOL. Press to decrease the speaker volume. Microphone NIGHT LIGHT Night light POWER light VOL. POWER PAGE Press to turn the night light on or off. On when night light is turned on. On when the baby unit is turned on. Press to increase the speaker volume. Press and hold to power on or off. Press to start or stop paging parent unit. Power jack 9 10 Speaker Night light auto-on You can turn on or off the night light by pressing the NIGHT LIGHT button manually on the baby unit. You can also use the parent unit to set the night light on the baby unit to automatically turn on whenever sounds are detected from the baby unit. When the night light auto-on setting is set to YES, displays. The default setting is preset to NO. Press MENU when the parent unit is not in 1. use. Press VOL. to choose NIGHTLIGHT, then press SELECT. Press SELECT to choose AUTO ON. Press VOL. NO. Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. to choose YES or or VOL. or VOL. 3. 4. 2. 5. NOTES To enter the night light menu of the parent unit, the baby unit must be turned on. If the night light on the baby unit is already on, the night light will go off immediately when you change the night light auto-on setting from YES to NO. If the night light on the baby unit is already on and the night light auto-on setting is YES, the night light on the baby unit will go off immediately after you press NIGHT LIGHT and the night light auto-on feature will become inactive for 5 minutes. For night light triggered by babys sound or turned on manually at the baby unit, it will automatically turn off after 15 minutes of silence. Language You can select a language (English, French or Spanish) to be used in all screen displays. The language is preset to English. 1. Press MENU when the parent unit is not in use. Press VOL. to choose LANGUAGE, then press SELECT. Press VOL. to choose ENGLISH, FRANCAIS or ESPANOL. Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. or VOL. or VOL. NOTE The language setting on each parent unit is independent. 2. 3. 4. Frequently asked questions Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, visit our website at www.vtechphones.com or call 1 (800) 595-9511 for customer service. Why does the baby monitor not respond normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby unit and the parent units. 2. Remove the batteries in the parent units. Then, install the batteries again. Why dont I hear a sound/

Why cant I hear my baby cry?

Why does the parent unit beep?

Set default Use this feature to restore to the default settings. Restoring the default settings on one parent unit will also reset the shared settings for sensitivity and night light auto-on feature of the other parent unit. 1. or VOL. Press MENU when the parent unit is not in use. Press VOL. to choose SET DEFAULT, then press SELECT. Press VOL. NO. When you choose YES, press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. or VOL. to choose YES or 2. 3. 4.

-OR-

When you choose NO, press SELECT to confirm your selection. The screen displays the previous menu. Talk to the baby unit You can broadcast messages from a parent unit to the baby unit and the other parent unit. If you have two parent units, you can use both of them at the same time to talk to the baby unit. Press and hold TALK on the side of the parent unit. The screen displays TALK when the voice connection to the baby unit is made. Speak towards the MIC on the parent unit. Your voice is broadcast to the baby unit and the other parent unit. NOTE When a parent unit is talking to the baby unit, it is also broadcast to the other parent unit. However, sounds from the baby unit cannot be transmitted to the parent units at the moment. Find/page the parent unit Use this feature to find misplaced parent units. 1. Press PAGE on the baby unit. All idle parent units ring and display PAGING. To end paging, press any key on the parent unit, or press PAGE on the baby unit. NOTES Paging rings all parent units even if the speaker volume of parent unit is set to VOLUME OFF. The baby unit cannot page any parent unit that is turned off, out of range or talking to the baby unit. 2. number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-

conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging. For cETL compliance only Mesures de scurit importantes Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent:

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. Linstallation par un adulte est requise. Ce produit a t conu pour tre un dispositif dappoint seulement. Il nest pas le remplacement dune supervision responsable et adquate par un adulte et ne devrait pas tre utilis comme telle. Ce produit nest pas conu pour tre utilis en tant que moniteur mdical. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 2. 3. 4. 5. General product care To keep this product working well and looking good, follow these guidelines:

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). DO NOT expose it to direct sunlight or moisture. Avoid dropping the product or treating it roughly. Clean with a soft cloth. DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap. DO NOT use cleaning spray or liquid cleaners. Make sure the baby unit and parent unit are dry before you connect them to the mains again. Storage When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. MISE EN GARDE: Il peut y avoir un risque dexplosion si vous utilisez le mauvais type de piles pour lunit du parent. Nutilisez que le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT166342/BT266342). Nincinrez pas les piles. Celles-ci risqueraient dexploser. Jetez les piles uses selon les renseignements suivant le sceau du RBRCMD. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. Adaptateur de lunit du bb: Entre 100-120V CA 150 mA 60 Hz; Sortie : 6 V CC 400 mA. Adaptateur de lunit du parent: Entre 100-120V CA 150 mA 60 Hz; Sortie : 6 V CC 400 mA. Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. Pour les PRODUITS BRANCHER UNE PRISE DE COURANT, la prise de courant doit tre installe prs du produit, afin dassurer une accessibilit scuritaire la prise de courant. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. Dbranchez les cordons dalimentation avant de remplacer le bloc-piles. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et 3. Wait a few minutes before connecting power back to the baby units and the parent unit. 4. Turn on the baby unit and the parent units. 5. Wait for the parent units to synchronize with the baby unit. Allow up to one minute for this to take place. Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not connected to the power. Insert the appliance plug into the parent unit and put the adapter in a wall socket. Perhaps the baby unit is not connected to the power. Connect the baby unit to the power. The units may be too close to each other. Make sure the parent unit and the baby unit are at least 1 meter/3 feet away from each other. The baby unit also detects other sounds than those of your baby. Adjust the sensitivity level to a lower level or adjust the speaker volume on the parent unit. Why doesnt the screen of the parent unit go on when I switch on the unit?

Why doesnt the POWER light of the baby unit go on when I switch on the unit?

Why does the baby monitor produce a high-pitched noise?

Why does the parent unit react too quickly to other sounds?

18. 19. 20. 21. 22. 23. 24. nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. Examinez les composantes afin de vrifier si celles-ci ne sont pas endommages. Soyez avis de la perte de la confidentialit lorsque vous utilisez les ondes publiques. Les conversations peuvent tre entendues par dautres moniteurs de bb, des tlphones sans fil, des scanneurs, etc. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. Le produit nest pas conu pour tre utilis par des personnes (incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde 1. Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu. 2. 3. to increase the volume The volume of the parent unit may have set too low. Press VOL. level. You may have set a low sound sensitivity level. See Adjust the sound sensitivity of the baby unit to change the setting. If the parent unit is in mute and the sound alert feature is on, there is sound detected from the baby unit. The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). If the parent unit is powered by the provided battery, it may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 11 hours. The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible. Why cant I establish a connection?

Why is the connection lost every now and then? Why are there sound interruptions?

Important safety instructions When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. Adult setup is required. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. This product is not intended for use as a medical monitor. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 2. 3. 4. 5. 6. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion 4. 5. 6. Assurez-vous que le moniteur et le cordon de ladaptateur sont toujours hors de porte des enfants, au moins 1 mtre (3 pieds) de lenfant ou du berceau, pour viter tout risque de strangulation. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil):

Lorganisme Wireless Technology Research, LLC

(WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT166342/

BT266342) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC seal. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: Input 100-120V AC 150mA 60Hz; Output: 6V DC 400mA;

Parent unit power adapter: Input 100-120V AC 150mA 60Hz; Output: 6V DC 400mA. 8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11.Unplug the power cords before replacing batteries. 12.Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 13.Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 15.Do not overload wall outlets or use an extension cord. 16.Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 17.This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 18.Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. Limited warranty What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or Product to the extent that the problem is caused by use with non-VTech accessories; or Product whose warranty/quality stickers, product 2. 3. 4. 5. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. The RBRC seal The RBRC seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The RBRC program provides a convenient alternative to placing used nickel-metal batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation in RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. RBRC and 1 (800) 8 BATTERY are registered trademarks of Rechargeable Battery Recycling Corporation. should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference, including interference that may cause undesired operation. The term IC: before the certification/registration Technical specications Frequency control Transmit frequency Crystal controlled PLL synthesizer Baby unit: 1921.536-1928.448 MHz Parent unit: 1921.536-1928.448 MHz Channels 5 LCD 35 (x) x 21.2 (y) mm B&W LCD Nominal effective range Power requirement Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Parent unit: 2.4 V Ni-MH battery Baby unit power adapter:

Input: 100-120V AC 150mA 60Hz Output: 6V DC 400mA Parent unit power adapter:

Input: 100-120V AC 150mA 60Hz Output: 6V DC 400mA 19.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 20.You should test the sound reception every time you turn on the units or move one of the components. 21.Periodically examine all components for damage. 22.Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc. 23.Children should be supervised to ensure that they do not play with the product. 24.The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions 1. 2. 3. 4. 5. 6. Use and store the product at a temperature between 32oF and 104oF. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. Batteries should not be exposed to excessive heat such as bright sunshine or fire. Make sure the baby unit(s) and the adapter cord(s) are always out of reach of the baby, at least 3 feet away from the baby or crib, to avoid a possible strangulation hazard. Never place the baby unit(s) inside the babys crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible:

wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. 6. 7. 8. serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or Product returned without a valid proof of purchase

(see item 2 on the next page); or Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and Provide your name, complete and correct mailing address, and telephone number. 2. 3. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you Specifications are subject to change without notice. 2015 VTech Communications, Inc. All rights reserved. 10/15. DM223_CIB_V1.0 Document order number: 91-008851-010-100