| all | frequencies |
|
|
exhibits | applications |
|---|---|---|---|---|---|
| manuals | |||||
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual 1 | Users Manual | 898.87 KiB | January 03 2015 | |||
| 1 |
|
User Manual 2 | Users Manual | 1.38 MiB | January 03 2015 | |||
| 1 | Cover Letter(s) | January 03 2015 | ||||||
| 1 | External Photos | January 03 2015 | ||||||
| 1 | Internal Photos | January 03 2015 | ||||||
| 1 | ID Label/Location Info | January 03 2015 | ||||||
| 1 | Cover Letter(s) | January 03 2015 | ||||||
| 1 | RF Exposure Info | January 03 2015 | ||||||
| 1 | Test Setup Photos | January 03 2015 | ||||||
| 1 | Test Report | January 03 2015 |
| 1 | User Manual 1 | Users Manual | 898.87 KiB | January 03 2015 |
Charge the parent unit battery Once you have connected the parent unit and installed its battery, press to turn it on. The battery icon indicates the battery status (see the following table). NOTES The parent unit battery is fully charged after 12 hours of continuous charging. It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging. The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery. Battery status No battery is installed but operates using AC power, or the battery has been installed incorrectly. The battery has very little charge and may be used for only a short time. The battery is fully charged. Battery indicators The battery icon is off and displays. The screen displays
. The light flashes. The battery icon becomes solid . Action Install the parent unit battery. Charge without interruption
(at least 30 minutes). Charge without interruption
(about 30 minutes). To keep the battery charged, connect it to AC power when not in use. Using the baby monitor Power on or off the baby unit to power on the baby unit. The Press POWER light turns on. Press and hold baby unit. The POWER light turns off. again to power off the to power on the parent unit. The Power on or off the parent unit Press screen turns on. Press and hold parent unit. The screen turns off. again to power off the Turn on or off the parent unit screen You can turn on or off the parent unit screen without powering off the parent unit. You can still hear sound from the baby unit. on the parent unit at any time. Press Adjust the speaker volume for baby unit You can adjust the speaker volume.
/VOL on the baby unit at
/VOL or Press any time. Whats in the box Users manual VM312/VM312-2 Safe & SoundTM Full Color Video and Audio Monitor BC 2. Plug the battery connector securely into the socket. NOTES Make sure the supplied rechargeable battery with the label THIS SIDE UP facing up. Arrange the battery wire to avoid it obstructing the battery cover when closing. THIS SIDE UP 2 Connect and charge the battery NOTES Use only the battery supplied with this product. Use only the parent unit power adapter or the baby unit power adapter supplied with this product. Make sure the electrical outlets are not controlled by wall switches. The parent unit power adapter and baby unit power adapter are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Make sure the parent unit, the baby unit and the power adapter cord are out of reach of children. Connect the baby monitor 3. Align the battery compartment cover against the battery compartment. 4. Push the battery compartment cover down and click into place. 2 1 1 set for VM312;
2 sets for VM312-2 Install the battery You can power up the parent unit by connecting it to AC power or to the rechargeable battery provided. Even if the parent unit is connected to AC power, we recommend you also install the battery. This guarantees continual operation in case of a power outage. Install the battery as shown below. 1. Push the detent of the battery compartment cover and lift the cover to open. Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. Register online to get an additional 3-month warranty!
Visit www.vtechphones.com. Registration Register your product online for enhanced warranty support. Product news Learn about the latest VTech products. Parent unit overview 1 Visual sound indicator The visual sound indicator has two functions. One is to show the sound level detected by the baby unit. The other one is to show the volume level during speaker volume setting. Sound level detected by the baby unit One to three green lights indicate a moderate sound level detected by the baby unit. Additional red lights indicate a higher sound level detected by the baby unit (e.g. baby crying loudly). Speaker volume level One to three green lights indicate Level 1 to Level 3 of the speaker volume setting. Additional red lights indicate Level 4 to Level 5 of the speaker volume setting.
(On/off) Press to power on. Press and hold to power off. Press to turn on or off the screen. Battery level indicator Light on when the parent unit battery is being charged. Light flashes when the parent unit battery is low and needs charging. Light off when the parent unit battery is fully charged, or when no battery is installed. 2 3 4 Power jack Replace the battery To replace the battery, pull the battery out of the battery compartment and unplug the battery connector from the socket, then follow the steps above to install the battery. NOTES The operating time for using the rechargeable battery is short. If you want to monitor your baby for a long time, we recommend you connect the parent unit to AC power. If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage. 1 2 3 1 5 6 7 While viewing image, press to zoom in/out. POWER on/off indicator On when the parent unit is turned on. Flashes when in pairing process, or when connecting to baby unit while the baby unit is not available. Control key panel MENU/SELECT Press to enter the menu. While in a menu, press to choose an item, or save a setting. VOL Press to increase the speaker volume. While in the menu, press to scroll up. While viewing a zoomed image, press and hold to move the image upward. VOL Press to decrease the speaker volume. While in the menu, press to scroll down. While viewing a zoomed image, press and hold to move the image downward. While in a menu, press to choose the option on the left side. While viewing a zoomed image, press and hold to move the image leftward. While in a menu, press to choose the option on the right side. While viewing a zoomed image, press and hold to move the image rightward. 8 TALK While viewing image, press and hold to talk to the selected baby unit. 9 Microphone 10 Battery compartment cover 11 Slot for portable use 12 Speaker 13 Stand Parent unit display icons Parent unit main menu icons Connection status
-
displays when strong signal strength is detected between the baby unit and the parent unit.
-
-
-
, or displays when moderate signal strength is detected between the baby unit and the parent unit. displays when the link between the baby unit and the parent unit is lost. displays when the parent unit is searching for a baby unit. x
(x:1-4) Current view status
- Display the number of the baby unit that is being viewed. Zoom
- Display when the camera at the baby unit has zoomed in. Volume off
- Display when the volume is turned off. Sound activation
- Display when the sound activation is on. Battery status
-
animates when the battery is charging.
- displays solid when the battery is fully charged.
- displays when the battery is low and needs charging.
- displays when no battery is installed but operates using AC power, or the battery has been installed incorrectly. Camera selection You can select the screen to view images from a particular baby unit, or view all baby units in Patrol Mode. Brightness You can change the brightness of the screen. The LCD brightness is The LCD brightness is preset to
.
- brightest screen display.
- brighter screen display.
- average screen brightness.
- darker screen display.
- darkest screen display. Sensitivity With this feature, you can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sound sensitivity is preset to
..
- high sensitivity level.
- medium high sensitivity level.
- medium sensitivity level.
- medium low sensitivity level.
- low sensitivity level. Sound activation Automatically turns on the parent unit screen when a sound is detected in your babys room. When no sound is detected, the screen is off to save power.
- turn on sound activation.
- turn off sound activation. Pairing The baby units and parent unit provided are already paired. You can add or replace baby units (VM302 purchased separately) to your baby monitor system. Before use You may test the baby monitor before initial use, and at regular times thereafter. To test your video and audio monitor:
1. Place the parent unit and the baby units in the same room to test the product. Make sure the baby units are at least 3 feet away from the parent unit. Press POWER light turns on. to turn on the baby unit. The 2. Overview Baby unit overview Positioning the baby monitor NOTE This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such. CAUTION Keep the baby unit out of the reach of the baby. Never place or mount the baby unit inside the babys crib or playpen. 1. Place the baby unit at least 1 meter / 3 feet away from your baby. At least 1 meter
(3 feet) 1 2 3. Press screen turns on. to turn on the parent unit. The 1 NOTE If you experience audio feedback on either the parent unit or baby unit, move the parent unit further away until there is no more audio feedback; or press VOL on the parent unit to lower the audio feedback sound. 2. Place the parent unit at least 1 meter / 3 feet away from the baby unit. At least 1 meter (3 feet) 2 NOTE If both units are not connected, the parent unit displays unit is found after a while, it displays while searching for a baby unit. If no baby
. TIP You can increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby unit. Operating range The operating range of the baby monitor is up to 300 meters (1,000 feet) outdoors or 50 meters
(160 feet) indoors. The actual operating range may vary depending on the environmental conditions, and other interferences such as walls, doors, and other obstructions. Adjust the sound sensitivity of the baby unit You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sound sensitivity is preset to Sound sensitivity table for reference Icon display Sensitivity Description
. High sensitivity High sensitivity level The parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your babys room. Medium high sensitivity level The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly. Medium sensitivity level The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Medium low sensitivity level The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Low sensitivity level The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds. Turn on or off the sound activation The parent unit continuously monitors the sound level in your babys room. When the sound activation mode is on, the parent unit screen turns on when the baby unit detects a sound. As long as no sound is detected within 50 seconds, the parent unit screen is off to save power. When your baby starts to cry, the sound activation triggers the parent unit screen automatically turns on. 1. Press MENU/SELECT when the parent unit is not in use. Press VOL or VOL to scroll to Press turn off sound activation. Press MENU/SELECT to confirm your selection. to turn on, or to select or to
. NOTES If you mute the speaker while sound activation is on, then you hear a beep sound whenever the screen turns on. If you want to turn on the parent unit screen continuously while the sound activation is on, then set the sound sensitivity to
. 2. 3. 4. Select the camera You can select the screen to view images from a particular baby unit, or view all baby units in Patrol Mode. If you select Patrol Mode to view the images, the screen switches to view another baby unit automatically after some time. The switching is in chronological order:
. 1. Press MENU/SELECT when the parent unit is not in use. Press VOL or VOL to scroll to Press
(1, 2, 3 or 4) or Patrol Mode ( ). Press MENU/SELECT to confirm your selection. to select the desired baby unit 2. 3. 4. or to
. Zoom You can zoom in or out while viewing image from baby unit. Press Press and hold VOL , VOL , the zoomed image upward, downward, leftward or rightward correspondingly. Press again to zoom out. to zoom in. or to move 1. 2. 3. 4. Press MENU/SELECT when the parent unit is not in use. Press VOL or VOL to scroll to to adjust the sensitivity level. Press Press MENU/SELECT to confirm your selection. or
. TIP You can adjust the baby unit placement to improve the sound detection. Talk function You can use the TALK function of the parent unit to talk and comfort your baby. Press and hold TALK when the parent unit is viewing particular baby unit. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit. 1 2 3 4 5 6 7 8 9 Infrared LEDs Backup light for night vision. POWER on/off indicator On when the baby unit is powered on and currently linked to parent unit. Flashes when the baby unit is not linked to a parent unit; or the pairing process is in progress; or the parent unit is not viewing this baby unit. Power jack
(On/Off) Press to power on. Press and hold to power off. Night sensor Camera
/VOL Press to increase the listening volume. PAIR Press and hold to pair to the parent unit.
/VOL Press to decrease the listening volume. 10 Microphone 11 Speaker 12 Ball joint stand Pan or tilt to adjust the camera angle. 13 Base Night vision The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit detects low light levels, the infrared LEDs are switched on automatically. NOTE When the infrared LEDs are on, the image is in black and white. This is normal due to external light sources. TIP Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby units angle or place the baby unit at a higher level to prevent glare and blurry display. Add new baby unit (VM302) The baby units and parent unit provided are already paired. You can add or replace any baby units (VM302 purchased separately) to your video and audio monitor system. You can pair a maximum of four baby units to your parent unit. For more details, refer to the users manual that comes with your VM302 new baby unit. Portable use of parent unit
(optional) NOTE Sling is not included. You may need to buy a sling for portable usage. 1. 2. 3. Make sure battery is installed and charged. Unplug the power adaptor. Pinch the end of the sling and insert it into the slot on the top of the parent unit. Insert the one end of the sling into the other end of the sling, and fasten it. Adjust the speaker volume for parent unit You can adjust the speaker volume from to
, or turn it off. The preset speaker volume is
. Press VOL or VOL on the parent unit while viewing image from baby unit. When the speaker volume is set to off, the screen displays
. Adjust the LCD brightness of the parent unit You can adjust the brightness of the parent unit screen. The LCD brightness is preset to
. 1. 2. 3. 4. Press MENU/SELECT when the parent unit is not in use. Press VOL or VOL to scroll to Press Press MENU/SELECT to confirm your selection. to adjust the brightness. or
. Low sensitivity General product care Frequently asked questions To keep this product working well and looking good, follow these guidelines:
Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). DO NOT expose it to direct sunlight or moisture. Avoid dropping the product or treating it roughly. Clean with a soft cloth. DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap. DO NOT use cleaning spray or liquid cleaners. Make sure the baby unit and parent unit are dry before you connect them to the mains again. Storage When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place. California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-
conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging. For cETL compliance only Mesures de scurit importantes Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent:
1. Observez toutes les instructions et mises en garde inscrites sur lappareil. Linstallation par un adulte est requise. Ce produit a t conu pour tre un dispositif dappoint seulement. Il nest pas le remplacement dune supervision responsable et adquate par un adulte et ne devrait pas tre utilis comme telle. Ce produit nest pas conu pour tre utilis en tant que moniteur mdical. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. MISE EN GARDE: Il peut y avoir un risque dexplosion si vous utilisez le mauvais type de piles pour lunit du parent. Nutilisez que le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT188645/BT288645). Nincinrez pas les piles. Celles-ci risqueraient dexploser. Jetez les piles uses selon les renseignements suivant le sceau du RBRCMD. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. Adaptateur de lunit du bb: Entre 100-240V CA 150 mA 50/60 Hz; Sortie : 6 V CC 600 mA. Adaptateur de lunit du parent: Entre 100-240V CA 150 mA 50/60 Hz; Sortie : 6 V CC 600 mA. 2. 3. 4. 5. 6. 7. Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, contact customer service by visiting our website at www.vtechphones.com or calling 1 (800) 595-9511. Why does the baby monitor not respond normally?
Why dont the power-on light of the baby unit and parent unit go on when I switch on the units?
Why is my screen in black and white?
Why do I get glare or blurry display on my screen when viewing my baby at night?
Why does the baby monitor produce a high-
pitched noise?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit. 2. Remove the batteries in the parent unit. Then, install the batteries again. 3. Wait a few minutes before connecting power back to the baby units and the parent unit. 4. Turn on the baby units and the parent unit. 5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for this to take place. Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not connected to the mains. Insert the appliance plug into the parent unit and put the adapter in a to wall socket. Then, press switch on the parent unit and to establish connection with the baby unit. Perhaps the baby unit is not connected to the mains. Connect the baby unit to the mains. Then, set ON/OFF switch to ON to switch on the baby unit and to establish connection with the parent unit. The screen is in black and white during nighttime or in a dark room. This is normal due to external light sources. During nighttime or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect the image quality on your parent unit screen. Adjust the baby units angle or place the baby unit at a higher level to prevent glare and blurry display. The units may be too close to each other. Make sure the parent unit and the baby unit at least 1 metre/3 feet away from each other. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. Dbranchez les cordons dalimentation avant de remplacer le bloc-piles. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. The POWER light on the baby unit flashes and the parent unit displays
. The baby unit is unpaired from the parent unit. Pair the baby unit:
1. Press MENU/SELECT when the parent unit is not in use. Press VOL or VOL to choose Press VOL or VOL to choose a desired baby unit slot, then press MENU/SELECT. The screen displays Turn on the baby unit, and then immediately press and hold PAIR until the POWER light turns on. 2. 3. 4. When pairing is successful, the screen displays the image from the newly paired baby unit.
, and then If pairing fails, the screen displays . Try the pairing process again. Only one baby unit can be paired at a time. Why does the parent unit react too quickly to other sounds?
Why dont I hear a sound/
Why cant I hear my baby cry?
Why does the parent unit beep?
Why cant I establish a connection?
Why is the connection lost every now and then? Why are there sound interruptions?
The baby unit also detects other sounds than those of your baby. Adjust the sensitivity level to a lower level or adjust the speaker volume on the parent unit. The volume of the parent unit may have set too low. Press VOL to increase the volume level. You may have set a low sound sensitivity level. See Adjust the sound sensitivity of the baby unit to change the setting. The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). If the parent unit is powered by the provided battery, it may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 12 hours. The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible. 19. 20. 21. 22. 23. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. Examinez les composantes afin de vrifier si celles-ci ne sont pas endommages. Soyez avis de la perte de la confidentialit lorsque vous utilisez les ondes publiques. Les conversations peuvent tre entendues par dautres moniteurs de bb, des tlphones sans fil, des scanneurs, etc. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. Le produit nest pas conu pour tre utilis par des personnes (incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde 1. 2. 3. 4. 5. 6. Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu. Assurez-vous que le moniteur et le cordon de ladaptateur sont toujours hors de porte des enfants, au moins 1 mtre (3 pieds) de lenfant ou du berceau, pour viter tout risque de strangulation. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil):
Lorganisme Wireless Technology Research, LLC
(WTR), une firme de recherche indpendante, 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. of power supply in your home, consult your dealer or local power company. Do not overload wall outlets or use an extension cord. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. You should test the sound reception every time you turn on the units or move one of the components. Periodically examine all components for damage. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc. Children should be supervised to ensure that they do not play with the product. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Important safety instructions When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Follow all warnings and instructions marked on the product. Adult setup is required. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. This product is not intended for use as a medical monitor. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT188645/
BT288645) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC seal. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: Input 100-240V AC 150mA 50/60Hz; Output: 6V DC 600mA Parent unit power adapter: Input 100-240V AC 150mA 50/60Hz; Output: 6V DC 600mA. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Unplug the power cords before replacing batteries. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:
Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. Limited warranty What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?
During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or Product to the extent that the problem is caused by use with non-VTech accessories; or Product whose warranty/quality stickers, product 2. 3. 4. 5. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B) Industry Canada This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference, including interference that may cause undesired operation. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. The RBRC seal The RBRC seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The RBRC program provides a convenient alternative to placing used nickel-metal batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation in RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. RBRC and 1 (800) 8 BATTERY are registered trademarks of Rechargeable Battery Recycling Corporation. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/
provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase. Technical specications Frequency control Transmit frequency Crystal controlled PLL synthesizer Baby unit: 2407.5 - 2475 MHz Parent unit: 2407.5 - 2475 MHz Channels 21 LCD Nominal effective range Power requirement 2 Color LCD
(TFT 176x220 pixel) Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Parent unit: 3.6 V Ni-MH battery Baby unit power adapter:
Input: 100-240V AC 150mA 50/60Hz Output: 6V DC 600mA Parent unit power adapter:
Input: 100-240V AC 150mA 50/60Hz Output: 6V DC 600mA Cautions 1. 2. 3. 4. 5. 6. Use and store the product at a temperature between 32oF and 104oF. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. Batteries should not be exposed to excessive heat such as bright sunshine or fire. Make sure the baby unit(s) and the adapter cord(s) are always out of reach of the baby, at least 3 feet away from the baby or crib, to avoid a possible strangulation hazard. Never place the baby unit(s) inside the babys crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible:
wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. 6. 7. 8. serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or Product returned without a valid proof of purchase
(see item 2 on the next page); or Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and Provide your name, complete and correct mailing address, and telephone number. 2. 3. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you Specifications are subject to change without notice. 2015 VTech Communications, Inc. All rights reserved. 01/15. VM312-X_CIB_V3.0 Document order number: 91-007354-020-100
| 1 | User Manual 2 | Users Manual | 1.38 MiB | January 03 2015 |
Users manual VM302 Accessory baby unit for use with VTech model VM312/VM312-2 Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions. This manual has instructions on how to set up and pair your new baby unit. For complete instructions on using the baby unit, see the users manual that came with your video and audio monitor. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. Register online to get an additional 3-month warranty!
Visit www.vtechphones.com. Registration Register your product online for enhanced warranty support. Product news Learn about the latest VTech products. Important safety instructions When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the product. Adult setup is required. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. This product is not intended for use as a medical monitor. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: Input 100-240V AC 150mA 50/60Hz; Output: 6V DC 600mA. The power adapter are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapter to replace it with other plug, as this causes a hazardous situation. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. Do not overload wall outlets or use an extension cord. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. This product should not be placed in any area where proper ventilation is not 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. You should test the sound reception every time you turn on the units or move one of the components. Periodically examine all components for damage. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc. Children should be supervised to ensure that they do not play with the product. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Parts checklist Overview 5. baby unit(s) with anything such as a towel or a blanket. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible:
wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. Connect the baby unit Use only the baby unit power adapter supplied with this product. The baby unit power adapter is intended to be correctly oriented in a vertical or floor mount position. The prong are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Make sure the baby unit and the power adapter cord are out of reach of children. Power outlet not controlled by a wall switch Baby unit power adapter 2 1 1 2 3 4 5 6 7 8 Cautions 1. Use and store the product at a temperature between 32oF and 104oF. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. Make sure the baby unit(s) and the adapter cord(s) are always out of reach of the baby, at least 3 feet away from the baby or crib, to avoid a possible strangulation hazard. Never place the baby unit(s) inside the babys crib or playpen. Never cover the 2. 3. 4. Baby unit Infrared LEDs Backup light for night vision. POWER on/off indicator On when the baby unit is powered on and currently linked to parent unit. Flashes when the baby unit is not linked to a parent unit; or the pairing process is in progress; or the parent unit is not viewing this baby unit. Power jack
(On/Off) Press to turn on Press and hold to turn off. Camera
/VOL+
Press to increase the listening volume. PAIR Press and hold to pair to the parent unit.
/VOL-
Press to decrease the listening volume. Microphone 9 10 Speaker 11 Ball joint stand Pan or tilt to adjust the camera angle. 12 Base Before use Pair and replace extra new baby unit Each newly purchased baby units (VM302) must be paired to your video and audio monitor system (VM312/VM312-2). You can pair a maximum of four baby units to your parent unit. Each new baby unit must be paired to the parent unit before use. Make sure you power on the parent unit before pairing. To pair and replace a baby unit:
1. Press MENU/SELECT when the parent unit is not in use. to choose Press Press to choose a desired baby unit slot, then press MENU/SELECT. The screen displays or or
. 2. 3. If you choose an occupied baby unit slot, the new baby unit will replace the existing baby unit. 4. Press and hold on the new baby unit until the POWER light flashes. Then immediately press and hold PAIR until the POWER light turns on. When pairing is successful, the screen displays
, and then the image from the newly paired baby unit. If pairing fails, the screen displays . Try the pairing process again. Only one baby unit can be paired at a time. To unpair a baby unit:
. 1. 2. 3. 4. 5. to scroll to to select the desired baby unit Make sure you power on the baby unit and the parent unit before unpairing the baby unit. Press MENU/SELECT when the parent unit is not in use. or Press Press or
(1, 2, 3 or 4). Press and hold TALK until display. Press confirm the unpair process. Press MENU/SELECT to confirm your selection. to cancel, or to select and 6. When unpairing is successful, the POWER light on the selected baby unit flashes. The parent unit displays image from the baby unit previously viewing. for a while, and then the or to Positioning the baby monitor Place the parent unit within the operating range of the baby unit. We recommend the parent unit is at least 3 feet away from the baby unit to avoid audio feedback. If you still experience audio feedback, move the parent unit and the baby unit farther apart. For better image quality, do not place the baby unit too far away from your baby. For desktop usage and/or wall mounting the baby unit, you can refer to Installation guide. Operating range The operating range of the baby monitor is up to 1,000 feet outdoors or 150 feet indoors. The actual operating range may vary depending on the environmental conditions and other interferences such as walls, doors and other obstructions. General product care To keep this product working well and looking good, follow these guidelines:
Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). DO NOT expose it to direct sunlight or moisture. Avoid dropping the product or treating it roughly. Clean with a soft cloth. DO NOT immerse the baby unit in water and do not clean them under the tap. DO NOT use cleaning spray or liquid cleaners. Make sure the baby unit is dry before you connect them to the mains again. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B) Industry Canada This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference, including interference that may cause undesired operation. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. Limited warranty What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?
During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or Product that has been damaged due to repair, alteration or modification by anyone other than an 2. 3. 4. 5. 6. 7. 8. authorized service representative of VTech; or Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or Product to the extent that the problem is caused by use with non-VTech accessories; or Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or Product returned without a valid proof of purchase
(see item 2 on the next page); or Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?
NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and Provide your name, complete and correct mailing address, and telephone number. 2. 3. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability
(an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase. Technical specifications Frequency control Transmit frequency Crystal controlled PLL synthesizer 2407.5 - 2475 MHz Channels 21 Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirement Input: 100-240V AC 150mA 50/60Hz Output: 6V DC 600mA Specifications are subject to change without notice. 2014 VTECH TELECOMMUNICATIONS LTD. All rights reserved. 03/14. VM302_CIB_V1.0 Document order number: 91-007355-010-100
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2015-03-01 | 2407.5 ~ 2475 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2015-03-01
|
||||
| 1 | Applicant's complete, legal business name |
VTech Telecommunications Ltd
|
||||
| 1 | FCC Registration Number (FRN) |
0015973951
|
||||
| 1 | Physical Address |
23/F Tai Ping Ind Center Block 1
|
||||
| 1 |
Tai Po NT, N/A
|
|||||
| 1 |
Hong Kong
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
c******@intertek.com
|
||||
| 1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
EW7
|
||||
| 1 | Equipment Product Code |
80-9602-00
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
M******** T******
|
||||
| 1 | Title |
Approbation Supervisor
|
||||
| 1 | Telephone Number |
852-2********
|
||||
| 1 | Fax Number |
852-2********
|
||||
| 1 |
m******@vtech.com
|
|||||
| app s | Technical Contact | |||||
| 1 | Firm Name |
Intertek Testing Services Hong Kong Ltd.
|
||||
| 1 | Name |
M******** N******
|
||||
| 1 | Physical Address |
Flat D, 5/F., Garment Centre
|
||||
| 1 |
Kowloon
|
|||||
| 1 |
Hong Kong
|
|||||
| 1 | Telephone Number |
(852)******** Extension:
|
||||
| 1 | Fax Number |
(852)********
|
||||
| 1 |
m******@intertek.com
|
|||||
| app s | Non Technical Contact | |||||
| 1 | Firm Name |
Intertek Testing Services Hong Kong Ltd.
|
||||
| 1 | Name |
M**** N******
|
||||
| 1 | Physical Address |
Flat D, 5/F., Garment Centre
|
||||
| 1 |
Kowloon
|
|||||
| 1 |
Hong Kong
|
|||||
| 1 | Telephone Number |
(852)******** Extension:
|
||||
| 1 | Fax Number |
(852)********
|
||||
| 1 |
m******@intertek.com
|
|||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 2.4GHz Baby Monitor-Baby Unit | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
| 1 | Grant Comments | The power listed is conducted. This device must transmit with a source-based time averaging duty factor as described in this filing. This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be informed of the operating requirements for satisfying RF exposure compliance. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Intertek Testing Services Hong Kong Ltd.
|
||||
| 1 | Name |
J****** H******
|
||||
| 1 | Telephone Number |
85221********
|
||||
| 1 | Fax Number |
85278********
|
||||
| 1 |
j******@intertek.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15C | 2407.50000000 | 2475.00000000 | 0.0364000 | ||||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC