FCC ID: EW780-2176-00 DECT 6.0 cordless telephone

Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. CS5319 CS5319-15 CS5319-2 DECT 6.0 cordless telephone Scan the QR code for support information CS5319-X (US) Quick start guide CS5319-X (CA) Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions. 2. 3. CAUTION: Do not install the telephone base at a height Follow all warnings and instructions marked on the product. above 2 meters. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, nor in a wet basement or shower. 6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 7. Avoid placing the telephone system in places with extreme 8. 9. temperature, direct sunlight, or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home or office, consult your dealer or local power company. 10. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on. 11. Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 12. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 13. Do not overload wall outlets and extension cords. 14. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

When the power supply cord or plug is damaged or frayed. If liquid has been spilled onto the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation. If the product has been dropped and the telephone base and/or handset has been damaged. If the product exhibits a distinct change in performance. 15. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning. 16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment containing concentrations of flammable or flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a fire or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents;

gasoline vapors; etc.); a leak of natural gas; etc. 17. Only put the handset of your telephone next to your ear when it is in normal talk mode. 18. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet. 19. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 20. CAUTION: Use only the batteries indicated in this All rights reserved. 07/23. CS5319-X_QSG_V4.0_20230714 2023 VTech Communications, Inc. Specifications are subject to change without notice. Basic operation Phonebook manual. There may be a risk of explosion if a wrong type of battery is used for the handset. Use only the supplied rechargeable batteries or replacement batteries (BT162342/

BT262342) for the handset. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the instruction. Disconnect the telephone line from the equipment before open the battery door. Do not use the battery in following conditions:

High or low extreme temperature during use, storage or transportation. defeat a safeguard. Replacement of a battery with an incorrect type that can Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. A battery subjected to extremely low air pressure that can result in an explosion or the leakage of flammable liquid or gas. product. Battery 21. Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously damage the product. 22. The applied nameplate is located at the bottom or near of the SAVE THESE INSTRUCTIONS Use only the battery provided or equivalent. To order a replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to phones.vtechcanada.com or call 1 (800) 267-7377. Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions. Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed. Exercise care in handling batteries in order not to create a short circuit with conductive materials. Charge the battery provided with this product only in accordance with the instructions and limitations specified in this manual. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless telephones at least six inches from the pacemaker. Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON. Should use the wireless telephone at the ear opposite the pacemaker. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones. About cordless telephones Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones. Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged, switched off or if the electrical power is interrupted. Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR often reduces or eliminates the interference. Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with conducting material such as rings, bracelets and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger. Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury. Whats in the box Quick start guide Install the battery Connect and activate Connect the telephone base If you subscribe to digital subscriber line (DSL) high-speed Internet service through your telephone line, make sure you connect a DSL filter (not included) to the telephone wall jack. a b 5 3 5 1 R C

. S E

. S L I P E I R S

) H M i-

N h E E T T A B T U A H E L S R Display c The battery is low and needs charging. The battery is charging. The battery is fully charged. 1 Handset ringer is muted. NEW ECO New voicemail received from your telephone service provider. There are new caller ID log entries. The ECO mode activates automatically to reduce power consumption when the handset is within range of the telephone base. Setup After the telephone is installed or power returns following a power outage and battery depletion, the handset will prompt you to set the date and time. Date and time Follow the steps below to set the date and time. For example, if the date is 25 January, 2023, and the time is 11:07 AM:

When the handset prompts you to set the date and time Date:MM/DD/YY Date:01/2?/YY Change LCD language settings Follow the steps below to set the date and time. For example, if the date is 25 January, 2023, and the time is 11:07 AM:

HANDSET Settings ECO 11:07 1/25 AM ECO 1. Press MENU. 2. Press q/p to scroll to Settings, then press SELECT. ECO ECO LCD language English 1. Enter the date. ECO ECO THIS SIDE UP / CE CT VERS LE HAUT Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH) WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES. NE PAS INCINRER OU PERCER LES PILES. Made in China / Fabriqu en chine CR1939 1 set for CS5319 CS5319-15 2 sets for CS5319-2 1 set CS5319-2 Charge the battery Find handset 12 hrs To find misplaced handsets, press

/FIND HS at the back of the telephone base. All idle handsets ring and display ** Paging **. To end paging, press

/FIND HS again or press OFF on the handset. Date:01/25/23 Time:1?:MM --

Time:11:07 AM ECO ECO ECO 2. Press SELECT. 3. Enter the time. 4. Press SELECT. NOTE: If you have skipped the prompt, you can set up again by pressing MENU to enter Set date/time, and then follow the steps above. 3. Press SELECT to select LCD language. 4. Press q/p to choose your desired language and press SELECT. Quiet mode When the telephone is in the Quiet Mode, all tones

(except the FIND HS tone) are muted. 1. Press and hold 2. Enter the numer of hours (1-12) you would like the telephone

. to be in Quiet Mode for. 3. Press SELECT to save. Ringer Settings Adjust the ringer volume indicating it meets the latest energy efficiency guidelines. proud to mark this product with the ENERGY STAR label save energy and help protect our environment. We are recognizes and encourages the use of products that The ENERGY STAR program (www.energystar.gov) license. Telecommunications Industry Association. Used under TIA-1083 Compliant Logo is a trademark of the equipped hearing aids and cochlear implants. The noise and interference when used with most T-coil Telephones identified with this logo have reduced TIA-1083 T Hearing Aid T-Coil Compatible with Make a call 1 Press Answer a call

- OR -

2 Enter the phone number Call block: 20 entries up to 24 digits and 15 characters Caller ID log: 30 memory locations;

up to 30 digits and 15 characters Phonebook: 50 memory locations;

Charger: 6V DC @ 400mA Telephone base: 6V DC @ 400mA Handset: 2.4V 300mAh Ni-MH battery Memory requirement Power Press

- OR -

- OR - Press any dialing key to answer conditions at the time of use. operating range may vary according to environmental Maximum power allowed by FCC and IC. Actual effective range Nominal End a call Speakerphone Volume 5 Channels Telephone base: 1921.536-1928.448 MHz Handset: 1921.536-1928.448 MHz Crystal controlled PLL synthesizer frequency Transmit control Frequency Press Press Press Technical specifications The phonebook can store up to 50 entries, which are shared by all handsets. Each entry may consist of a telephone number up to 30 digits, and a name up to 15 characters. Add a phonebook entry Follow the steps below to set the date and time. For example, if the date is 25 January, 2022, and the time is 11:07 AM:

HANDSET 800-595-9511 Enter number 800-595-9511_ ECO ECO 11:07 1/25 AM 11:07 1/25 AM ECO 1. Enter the phone number. 2. Press MENU. 3. Press SELECT. Enter name Mike Smith_ ECO ECO 4. Enter the phonebook entry name. 5. Press SELECT. Review phonebook entries HANDSET Mike Smith 800-595-9511 ECO 11:07 1/25 AM ECO 1. Press

. 2. Press q/p to browse the entries. Delete a phonebook entry Caller ID If you subscribe to caller ID service, information about each caller appears after the first or second ring. The caller ID log stores up to 30 entries. Each entry has up to 24 digits for the phone number and 15 characters for the name. Review Caller ID log entries HANDSET Mike Smith 800-595-9511 ECO 11:07 1/25 AM ECO When your desired phonebook entry displays on the handset screen:

1. Press

. 2. Press q/p to browse the entries. Save a Caller ID log entry to the phonebook When your desired caller ID entry displays on the handset screen Mike Smith 800-595-9511 To phonebook ECO ECO 11:07 1/25 AM 1. Press MENU. 2. Press SELECT to select To phonebook. Enter number 800-595-9511_ Enter name Mike Smith_ ECO ECO ECO Mike Smith 800-595-9511 Delete entry?

ECO ECO 1. Press DELETE. 2. Press SELECT. Dial a caller ID log entry When your desired caller ID entry displays on the handset screen ECO Mike Smith 800-595-9511 11:07 1/25 AM

-OR-

3. Edit the phone number if needed. 4. Press SELECT. 5. Edit the name if needed, then press SELECT. Press Delete a Caller ID log entry When your desired Caller ID entry displays on the handset screen:

Press DELETE. Mike Smith 800-595-9511 ECO 11:07 1/25 AM Call Block If you subscribe to caller ID service, you can set the telephone to block unknown calls and certain undesired calls. The call block list can store up to 20 entries. Add a call block entry HANDSET Call block Block list ECO 11:07 1/25 1. Press MENU. ECO ECO 2. Press q/p to scroll to Call block, then press SELECT. 3. Press SELECT to select Block list. Review a call block list entry Block unknown calls HANDSET Call block Block list HANDSET Call block Calls w/o num HANDSET Ringers Ringer volume ECO ECO ECO ECO ECO ECO ECO ECO ECO 11:07 1/25 1. Press MENU. Review 2. Press q/p to scroll to Call block, then press SELECT. 11:07 1/25 11:07 1/25 3. Press SELECT 1. Press MENU. to select Block list. 2. Press q/p to scroll to Call block, then press SELECT. 3. Press q/p to scroll to Calls w/o num, then press SELECT. 1. Press MENU. 2. Press q/p 3. Press SELECT to scroll to Ringer, then press SELECT. to select Ringer volume. Add new entry Enter number 800-595-9511_ Enter name ECO ECO ECO ECO 4. Press SELECT to select Review. 4. Press q/p to scoll to Add new entry, then press SELECT. 5. Enter 6. Enter number, and then press SELECT. name, and then press SELECT. Delete a call block list entry When your desired call block list entry displays on the handset screen:

Press DELETE. Mike Smith 800-595-9511 ECO 11:07 1/25 AM Block ECO 4. Press q/p to scroll to Block, then press SELECT. Volume:Off ECO 4. Press q/p to scroll to adjust volume level, then press SELECT to save. Ringer Settings (contd) Voicemail Service Change the ringer tone HANDSET Ringers Ringer tone Your telephone supports voicemail service offered by your telephone service provider (subscription is required, and fees may apply. ECO ECO ECO 11:07 1/25 Voicemail service Support by Telephone service provider 1. Press MENU. 2. Press q/p 3. Press SELECT Subscription Yes to scroll to Ringer, then press SELECT. to select Ringer tone, then press SELECT. Fees May apply Answer incoming calls Usually after 2 rings. It can be changed by contacting your telephone service provider. Storage Server or System Display new messages Retrieve messages Handset Press and hold and enter an access number and/

or passcode from your telephone service provider. on the dialpad, Tone:8 ECO 4. Press q/p to select a tone

(1-10), then press SELECT to save. Set a speed dial voicemail number This feature lets you save your voicemail number for quick access when you press and hold the key. HANDSET Settings ECO ECO 11:07 1/25 1. Press MENU. Voicemail #

ECO 2. Press q/p to scroll to Settings, then press SELECT. Voicemail #

_ ECO 3. Press q/p to scroll to Voicemail #, then press SELECT. 4. Enter your voicemail access number, then press SELECT to save. FCC, ACTA and IC regulations FCC Part 15 NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone. To ensure safety of users, the FCC/ISEDC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC/ISEDC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the users body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B). FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your telephone service provider upon request. The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line. See the installation instructions in the users manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your telephone service provider. This equipment must not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone service provider or a qualified installer. If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited warranty. If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue your telephone service. The telephone service provider is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone service provider is required to inform you of your right to file a complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone service provider is required to notify you if such changes are planned. If this product is equipped with a corded or cordless handset, it is hearing aid compatible. If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:

Remain on the line and briefly explain the reason for the call before hanging up. Perform such activities in off-peak hours, such as early morning or late evening. ECO HANDSET Clear the voicemail indicator Use this feature to turn off the displayed icon on your handset LCD. It does not delete your voicemail messages. As long as you have new voicemail messages, your telephone service provider will continue to send the signal to turn on the indicator. 1. Press MENU. 11:07 1/25 Settings ECO 2. Press q/p to scroll to Settings, then press SELECT. Clr voicemail Clr voicemail ECO ECO 3. Press q/p to 4. A confirmation scroll to Clr voicemail, then press SELECT. tone plays to indicate that the icon has been cleared. Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Privacy of communications may not be ensured when using this telephone. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Need Help?

For operations and guides to help you using your telephone, and for the latest information and supports, go and check the online help and FAQs. Use your smartphone or mobile device to access. Go to https://help.vtechphones.com/CS5319 (US);

https://phones.vtechcanada.com/en/support/

technical-support/product/4532 (CAN); OR Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the devices camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help. You can also call our Customer Support at 1(800) 595-9511 [in the US] or 1(800) 267-7377

[in Canada] for help. Recycle this product when you are done with it Scan the QR code on the right or visit www.vtechphones.com/recycle.

(For the US only) 7. 8. CS5319-X US CS5319-X CA For C-UL compliance only Mesures de scurit importantes Afin de rduire les risques dincendie, de blessures corporelles ou dlectrocution, suivez toujours ces mesures prventives de base lorsque vous utilisez votre tlphone :

1. 2. Observez toutes les instructions et mises en garde inscrites sur Lisez et comprenez bien toutes les instructions. lappareil. California energy commission battery charging testing instructions This telephone is set up to comply with the energy-conserving standards right out of the box. These instructions are intended for California Energy Commission (CEC) compliance testing only. When the CEC battery charging testing mode is activated, all telephone functions, except battery charging, will be disabled. To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with charged batteries before proceeding. 2. While you press and hold FIND HS at the back of the telephone base, plug the telephone base power adapter back to the power outlet. 3. After about 10 seconds, release FIND HS and immediately press it again within two seconds. When the phone successfully enters the CEC battery charging testing mode, all handsets display To register HS... and ...see manual alternately. When the phone fails to enter this mode, repeat steps 1 to 3 above. To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it back in. Then the telephone base is powered up as normal. 2. Press and hold FIND HS at the back of the telephone base for about four seconds. 3. Press #/QUIET on the handset and it shows Registering.... The handset shows Registered and you hear a beep when the registration process completes. This process takes about 60 seconds. 3. Dbranchez ce tlphone de la prise murale avant de le nettoyer. Nutilisez pas de nettoyeurs liquides ni en arosol. Nutilisez quun chiffon doux et lgrement humect. 4. ATTENTION: Ne pas installer le socle tlphonique une hauteur suprieure 2 mtres. 5. Nutilisez pas ce produit prs de leau, tel que prs dun bain, dun lavabo, dun vier de cuisine, dun bac de lavage ou dune piscine, ou dans un sous-sol humide ou sous la douche. 6. Ne dposez pas ce tlphone sur un chariot, support ou table chancelants. Lappareil pourrait tomber et tre srieusement endommag. vitez dinstaller le systme tlphonique dans les endroits soumis une temprature extrme, la lumire directe du soleil ou proximit immdiate dautres appareils lectriques ou lectroniques. Protgez votre tlphone contre les sources dhumidit, la poussire, les vapeurs et les liquides corrosifs. Le botier de lappareil est dot de fentes et douvertures daration situes larrire ou en dessous. Afin dempcher la surchauffe, ces ouvertures ne doivent pas tre obstrues en plaant lappareil sur un lit, divan, tapis ou autre surface similaires. Ne placez pas cet appareil proximit dun lment de chauffage ni dune plinthe lectrique. De plus, ne linstallez pas dans une unit murale ou un cabinet ferm qui ne possde pas daration adquate. 9. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur les tiquettes de lappareil. Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur dlectricit. 10. Ne dposez rien sur le cordon dalimentation. Installez cet appareil dans un endroit scuritaire, l o personne ne pourra trbucher sur la ligne dalimentation ni le cordon tlphonique modulaire. 11. Ninsrez jamais dobjets travers les fentes et ouvertures de cet appareil, car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices, ce qui constituerait un risque dincendie ou dlectrocution. Nchappez pas de liquides dans lappareil. 12. Afin de rduire les risques dlectrocution, ne dmontez pas lappareil, mais apportez-le plutt un centre de service qualifi sil doit tre rpar. En enlevant le couvercle, vous vous exposez des tensions dangereuses ou autres dangers similaires. Un remontage inadquat peut tre lorigine dune lectrocution lors dune utilisation ultrieure de lappareil. Dbranchez Limited warranty What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package

(Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty;

whichever is longer. lappareil avant de procder au nettoyage. Utilisez un chiffon humide et doux. 13. Ne surchargez pas les prises de courant et les rallonges. 14. Dbranchez cet appareil de la prise de courant et communiquez avec le dpartement de service la clientle de VTech dans les cas suivants :

Lorsque le cordon dalimentation est endommag ou corch. Si du liquide a t chapp dans lappareil. Si lappareil a t expos une source dhumidit telle que la pluie ou leau. Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Rglez uniquement les commandes indiques dans le les instructions de fonctionnement. Les rglages incorrects des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de la part dun technicien autoris afin de rtablir le fonctionnement normal de lappareil. Si le produit a t chapp et que le socle et/ou le combin a t endommag. Si le produit affiche une nette diminution de sa performance. 15. vitez dutiliser un tlphone (autre quun sans fil) pendant un orage. Les clairs peuvent tre lorigine dune lectrocution. 16. Nutilisez pas le tlphone pour rapporter une fuite de gaz proximit de la fuite. En certaines circonstances, une flammche pourrait tre provoque lorsque ladaptateur est branch une prise de courant, ou lorsque le combin est dpos sur le socle. Ceci est un vnement commun associ la fermeture dun circuit lectrique. Lutilisateur ne devrait pas brancher le tlphone une prise de courant, et ne devrait pas dposer le combin charg sur le socle, si le tlphone se trouve proximit dun endroit comportant des concentrations de gaz inflammables, moins que la ventilation soit adquate. Une flammche dans un tel endroit pourrait provoquer un incendie ou une explosion. De tels environnements peuvent comprendre:

des endroits o lon utilise de loxygne mdical sans ventilation adquate; des gaz industriels (dissolvants de nettoyage, des vapeurs dessence, etc.); une fuite de gaz naturel, etc. 17. Ne placez que le combin de votre tlphone prs de votre oreille lorsquen mode de conversation. 18. Ces adaptateurs ont t conus pour tre orients en position verticale ou monts au sol. Les broches ne sont pas conues pour maintenir ladaptateur en place si celui-ci est barnch dans une What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion. Product that has been subjected to contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like; but then only to the extent the damage was not caused by incorrectly securing the waterproof handsets protective elements, for example, failing to properly close a seal), or such protective elements are damaged or missing (e.g. a cracked battery door), or subjecting a Product to conditions beyond its stated specifications or limits (e.g. 30 minutes in 1 meter of fresh water). Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech;

Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems;

Product to the extent that the problem is caused by use with non-VTech accessories;

Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible;

Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes);

Product returned without a valid proof of purchase (see item 2 below); or Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. 2. 3. 4. 5. 6. 7. 8. 9. prise au plafond ou sous une table/ armoire. 19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant doit etre installe a proximite du materiel et doit etre aisement accessible. 20. MISE EN GARDE: Il peut y avoir un risque dexplosion si vous utilisez le mauvais type de piles pour le tlphone. Nutilisez que les piles rechargeable inclus ou les piles de rechange (BT162342/BT262342). Nincinrez pas les piles. Celles-ci risqueraient dexploser. 21. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. 22. La plaque signaltique applique est situe au bas ou proximit du produit. CONSERVEZ CES INSTRUCTIONS Pile Nutilisez que la pile incluse ou lquivalent. Pour commander une pile de recharge, visitez notre site Web au www.vtechphones.com ou composez le 800-595-9511. Au Canada, visitez le phones.vtechcanada.com ou composez le 800-267-7377. Ne jetez pas la pile au feu. Vrifiez les instructions spcifiques de mise aux rebus auprs des autorits locales. Nouvrez pas et ne mutilez pas la pile. Llectrolyte qui sen chapperait est corrosif et pourrait causer des brlures ou des blessures aux yeux ou la peau. Llectrolyte est toxique si aval. Soyez prudents lorsque vous manipulez les piles afin dviter les courts-circuits provoqus par des matriaux conducteurs. Rechargez la pile incluse avec cet appareil, selon les instructions et limites spcifies dans ce guide dutilisation. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (sapplique uniquement aux tlphones numriques sans fil) :

Lorganisme Wireless Technology Research, LLC (WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les How do you get warranty service?

To obtain warranty service in the United States of America, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual

- a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty;

and Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and Provide your name, complete and correct mailing address, and telephone number. 2. 3. tlphone sans fil prs ou sur un tlviseur ou magntoscope. Sil y a prsence de parasites, il est conseill dloigner le tlphone sans fil du tlviseur ou du magntoscope afin de rduire possiblement les interfrences. Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter avec des bagues, bracelets ou cls. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la polarit adquate entre la pile et le chargeur. Les bloc-piles rechargeables lhydrure mtallique de nickel :

Jetez ces blocs-piles de manire cologique et scuritaire. Ne les incinrez pas et ne les percez pas. Tel que les autres piles de ce type, elles pourraient dgager une matire toxique qui peut causer des blessures corporelles si elles sont brles ou perces. The RBRC seal The RBRC seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used nickel-metal hydride batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY are registered trademarks of Call2recycle, Inc. Disclaimer and Limitation of Liability VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this users manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product. Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins :

Avis aux dtenteurs de stimulateurs cardiaques Ils doivent tenir le tlphone sans fil une distance dau moins six pouces du stimulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ils doivent utiliser le tlphone sans fil en lappuyant sur loreille qui se trouve dans la direction oppose au stimulateur cardiaque. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent un tlphone sans fil proximit de ceux-ci. propos des tlphones sans fil Confidentialit : Les mmes caractristiques qui constituent des avantages pour les tlphones sans fil affichent galement des restrictions. Les appels tlphoniques sont transmis entre le combin sans fil et le socle par le biais dondes radio ; il y a donc la possibilit que vos conversations tlphoniques sans fil soient interceptes par des quipements de rception radio se trouvant dans la porte du combin sans fil. Pour cette raison, vous ne devez pas percevoir les communications tlphoniques sans fil comme tant aussi confidentielles que celles des tlphones cordons. Alimentation lectrique : Le socle de ce tlphone sans fil doit tre branch une prise lectrique fonctionnelle. La prise lectrique ne doit pas tre contrle par un interrupteur mural. Les appels ne pourront pas tre effectus du combin sans fil si le socle est dbranch ou mis hors tension ou si le courant est coup. Possibilit dinterfrences aux tlviseurs : Certains tlphones sans fil fonctionnent sur des frquences pouvant causer des interfrences aux tlviseurs et aux magntoscopes. Pour rduire ou prvenir de telles interfrences, ne placez pas le socle du Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase

SN Label 28X10 mm Model: CS5319 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS5319-2 S/N: XXXXXXXXXXXXXXXXXXXX Model: CS5319 S/N: XXXXXXXXXXXXXXXXXXXX 4H20 I.T.E. VTech Customer Service 1-800-595-9511 www.vtechphones.com Text : Recessed 0.3mm High Gloss RINGER EQUIVALENCE: 0.1A USOC JACK: RJ11C/RJ11W DC 6V 400mA HAC FCC ID: EW780-2176-00 CORDLESS TELEPHONE VTECH TELECOMMUNICATIONS LTD. MANUFACTURED IN CHINA COMPLIES WITH 47 CFR PART 68 Reg. No.: US: EW7W401A80-217600 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. Text : Recessed 0.3mm High Gloss TEL. LINE 6V Use Only Supplied Adapter Text: engraved in raised 0.3mm

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax:(852)2680 5252 E-mail: Michael_Tsui@vtech.com ATTESTATION STATEMENT Date: 2023-12-26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(5)(i), (ii) Filing FCC ID: EW780-2176-00 VTech Telecommunications Ltd certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. VTech Telecommunications Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com FCC Authorization Date: 2023-12-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, VTech Telecommunications Ltd, the undersigned, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature Michael Tsui Approbation Supervisor QA-FR-170-B

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com FCC Confidential Authorization Date: 2023-12-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: EW780-2176-00 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, VTech Telecommunications Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Dec. 26, 2023 To whom it may concern, FCC-Multiple Models Confirmation Letterbase I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows:

Electrical designs, including software & firmware PCB layout Others, please specify Construction design/Physical design/Enclosure The only differences between these models are the follows for marketing purpose:

Color Trade name Others, please specify Package type, no. of Handset and Charger. Cosmetic details Model number Suffix ( X,Y, Z in CS531Z-XY and VG231-XY) represents Color code Others, please specify

,but models with suffix (

Packing configuration Z= any alphanumeric character is presenting different package type (material). X= any alphanumeric character or blank is presenting number of Handset and extra Charger. Y= any alphanumeric character or blank is presenting different color of enclosure. X,Y,Z

) are identical in:

Electrical designs, including software & firmware PCB layout Construction design/Physical design/Enclosure Others, please specify For the product subject to authorization under FCC Declaration of Conformity:

In addition, it is to confirm that all the below information 1) The U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual Are the same but different in the following model numbers only:

Item # New Model Model Number Trade Name Remarks 1 2 3 4 5 6 7 8 9 10 YES YES YES YES YES YES YES YES YES YES CS5319 CS5319-15 CS5319-2 CS531Z-XY VG231 VG231-2 VG231-3 VG231-4 VG231-5 VG231-XY vtech vtech vtech vtech vtech vtech vtech vtech vtech vtech 1HS+1BS 1HS+1BS 2HS+1BS+1charger XHS+1BS+(X-1)chargers 1HS+1BS 2HS+1BS+1charger 3HS+1BS+2chargers 4HS+1BS+3chargers 5HS+1BS+4chargers XHS+1BS+(X-1)chargers VTech Telecommunications Ltd The sample(s) being submitted to China Certification ICT Co., Ltd (Dongguan) for conformity assessment is CS5319-2 of the above list. All above models FCC ID is EW780-2176-00 Regards, Michael Tsui Approbation Supervisor

U.S. AGENT LETTER OF ATTESTATION Date: 2023-03-20 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(7) Filing VTech Telecommunications Ltd certifies that, as of the date of the filing of the application, VTech Communications, Inc. is our designated U.S. agent for service of process for the FCC ID. VTech Telecommunications Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-

related proceeding involving the equipment. VTech Communications, Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the FCC ID. Designated U.S. Agent Information:

Company Name: VTech Communications, Inc. Address: 9020 SW Washington Square Road, Tigard OR 97223 Agent FRN : 0033411265 Tel.: +1(503) 596-1212 Email: cconrad@vtechphones.com Signed by: Chris Conrad Signature:

Applicant Company Name: VTech Telecommunications Ltd Address: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Applicant FRN: 0015973951 Tel: (852)2680 5398 Email: Michael_Tsui@vtech.com Signed by: Michael Tsui Signature:

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com Date: 2023-12-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

The RF chip, model BK3296QN202, installed in our product DECT 6.0 cordless telephone (Base), Model: CS5319-2, CS5319, CS5319-15, CS531Z-XY, VG231, VG231-2, VG231-3, VG231-4, VG231-5, VG231-XY, FCC ID: EW780-2176-00, supports BDR (GFSK), EDR (/4-DQPSK, 8DPSK) and BLE functions. For use in America and this chip will not support/enable BLE. The BLE has been shielded by the manufacturer using the software, the end user has no capability to activate it. Sincerely Yours, Signature Michael Tsui Approbation Supervisor