Whats in the box 1 Connect and charge the battery Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news. DM1212 DM1212-2 Audio Baby Monitor Quick start guide Document order number: 96-012974-010-100 All rights reserved. 01/20. DM1212-X_QSG_V1 2020 VTech Communications, Inc. Specifications are subject to change without notice. Output: 6V DC 400mA Parent unit power adapter:
Output: 6V DC 400mA Baby unit power adapter:
Parent unit: 2.4 V Ni-MH battery Nominal effective rangeMaximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirement 35 (x) x 21.2 (y) mm B&W LCD 5 LCD Channels Parent unit: 1921.536-1928.448 MHz Baby unit: 1921.536-1928.448 MHz Transmit frequency Crystal controlled PLL synthesizer Frequency control Technical specifications Important safety instructions When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. 4. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT166342/BT266342) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC seal. 6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: Output: 6V DC 400mA;
Parent unit power adapter: Output: 6V DC 400mA. 7. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 8. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 9. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 10. Unplug the power cords before replacing batteries. 11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. Do not overload wall outlets or use an extension cord. 15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 19. You should test the sound reception every time you turn on the units or move one of the components. 20. Periodically examine all components for damage. 21. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc. 22. Children should be supervised to ensure that they do not play with the product. 23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between 32oF and 104oF. 2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire. 4. WarningStrangulation HazardChildren have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9 m) away). Do not remove this tag. 5. Never place the baby unit inside the babys crib or playpen. Never cover the baby unit or parent unit with anything such as a towel or a blanket. 6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. Quick start guide a T B t t e r W H I D A B S y T 1 N O R E N M N 6 a I N 6 c a P O 3 k P S I D d A T G 4 B
2
e S i I N n U R V T C C E 2 l o c
E B U A B P
h i I N N n O T E R 6 p C 6 i l I 3 e a
F R S 4 s R E S P R E U a b O N M
2
2
. 4 r i U V C E q T N u P U T 7 C T V
R 0 5 E E e R n C c E E m B A R S L E H h N i
M H
) h R A i T n L T e E E I E S
. P S L I E S
. R A U T C R 1 9 3 7 1 set for DM1212 2 sets for DM1212-2 1 Connect and charge the battery Install the parent unit battery NOTES NOTE Use only the battery supplied with this product. If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage. 1 1 2 THIS SIDE UP 2 Made in China / Fabriqu en chine CR1937 NE PAS INCINRER OU PERCER LES PILES. DO NOT BURN OR PUNCTURE BATTERIES. WARNING / AVERTISSEMENT :
BT166342/BT266342 (2.4V 750mAh Ni-MH) Battery Pack / Bloc-piles :
THIS SIDE UP / CE CT VERS LE HAUT 3 4 3 4 2 Power on or off the baby monitor 3 Positioning the baby monitor Basic operation Baby unit overview Press Press and hold to power on the baby unit. The power light turns on. to power off the baby unit. The power light turns off.
> 3ft (1m) Adjust speaker volume Press volume.
to adjust your parent unit speaker Turn on vibration alert feature is on. is shown on LCD display once this Press and hold to power on or off the parent unit. Caution The default volume of your parent unit is level 3. If you experience high-pitched screeching noise from your baby monitor while positioning:
- Make sure your baby unit and parent unit are more than 6.5 feet (2 meters) apart, OR
- Turn down the volume of your parent unit. NOTENote NOTES To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers. Talk to your baby unit Turn on the nightlight Press to turn on the night light. Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when finish talking and hear your baby again.
> 6.5ft (2m)
< 6.5ft (2m) 3ft (1m)
< 3ft (1m) LINKED LINKED
> 6.5ft (2m) Caution For hearing protection, make sure the parent unit is more than 6.5 feet (2 meters) away from the baby unit. If you hear any high-pitched noise, move the parent unit further until the noise stops. You can also press mute the noise. on the parent unit to lower or Press and hold Connect the baby monitor NOTES NOTE Use only the power adapters supplied with this product. Make sure the baby monitor is not connected to a switch-controlled electric outlet. Connect the power adapters in a vertical or floor mount position only. The adapters prongs are not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the baby unit and the power adapter cords are out of reach of With audio reminder feature preset to ON, the parent unit plays an audio reminder when children. it is connected to a baby unit. 2 2 1 1 6 7 1 2 3 4 5 8 9 6 7 10 11 12 S m 1 2 3 4 5 Projector ball 1 2 Microphone 3 PAGE Press to start or stop paging parent unit. 4 8 5 6 7 Press to turn the night light on or off. Press to power on, and the power light 10
(On/off) turns on. 9 11 Press and hold to power off, and the power light turns off. Power light On when the baby unit is turned on. 12 Projection on/off Press to turn the projection on or off. 9 10 11 12 8 Night light On when night light is turned on Off when night light is turned off manually. manually. Speaker Press to increase the speaker volume. Press to decrease the speaker volume. Power jack Get help with the online topics For operations and guides to help you using your video monitor, and for latest information and supports, go and check the online help topics and online FAQs. Use your smartphone or mobile device to access our online help. Go to https://help.vtechphones.com/dm1212; OR Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the devices camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help.
If the QR code is not clearly displayed, adjust your cameras focus by moving your device closer or further away until it is clear. Parent unit overview Parent unit icons Sound sensitivity and sound activation The RBRC seal Adjust sound detection sensitivity High Highest Adjust the sound sensitivity of the baby unit You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The VOX sensitivity level is preset to HIGHEST. VOX Sensitivity level Description The parent unit speaker is constantly on, and you will hear all sounds
(including background noises) from your babys room. The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly. The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds. The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds. The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Medium Lowest Low 1. Press MENU when the parent unit is not in use. 2. Press SELECT to select VOX LEVEL. 3. Press 4. Press SELECT to confirm your selection. The screen displays SAVED and you hear a to choose the desired sensitivity level. or confirmation tone. Note To enter the VOX Level menu of the parent unit, the baby unit must be turned on. The RBRC seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The RBRC program provides a convenient alternative to placing used nickel-metal batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation in RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. RBRC and 1 (800) 8 BATTERY are registered trademarks of the Rechargeable Battery Recycling Corporation. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. Caution: This Transmitter must be installed to provide a separation distance of at least 20cm from all persons. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. For body worn operation, this parent unit has been tested and meets the FCC RF exposure guidelines when used with the accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging. 2. Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights:
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase. 5 6 10 11 12 7 8 9 1 2 3 4 5 6 13 14 1 Visual sound indicator 7 Battery LED The visual sound indicator shows the sound level detected by the baby unit. 10 11 One to three green lights indicate a moderate sound level detected by the baby unit. Additional red lights indicate a higher sound level detected by the baby unit (e.g. baby 14 crying loudly). 13 2 LCD display 3 Microphone 4 12 Press to decrease the speaker volume. Press repeatedly until the volume reaches the minimum to turn it off. While in a menu, press to scroll down. MENU Press to enter the menu. While in a menu, press to return to the previous menu. 5 6 Speaker Light on when the battery is being charged. Light flashes when the battery is low and needs charging. Light off when the parent unit is running on AC power without battery installed, or the parent unit is running on battery only. Press to increase the speaker volume. While in a menu, press to scroll up. SELECT While in a menu, press to choose an 8 9 item, or save a setting.
(On/off) 10 Press and hold to power on, the screen turns on. Press and hold again to power off, the screen turns off. While in a menu, press to return to idle screen. 11 TALK Press and hold to talk to the baby. Power jack Belt clip 12 13 14 Battery compartment cover For c-ETL compliance only Mesures de scurit importantes La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur lappareil. 2. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilit du parent Linstallation par un adulte est requise. ou de la personne qui soccupe de lenfant. Ce produit pourrait cesser de fonctionner et, par consquent, vous ne devriez pas prsumer quil continuera de fonctionner correctement pendant une priode de temps donne. De plus, il ne sagit pas dun instrument mdical et ne devrait pas tre utilis comme tel. Ce produit est destin vous aider superviser votre bb. 5. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque dexplosion si un autre type de batterie est utilis pour lunit Parents. Nincinrez pas les piles. Celles-ci risqueraient dexploser. Jetez les piles uses selon les renseignements suivant le sceau du RBRC. 6. 7. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait 8. inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. Adaptateur de lunit du bb : Sortie : 5V CC 600mA Adaptateur de lunit du parent : Sortie : 5V CC 1A Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. 9. Pour les PRODUITS BRANCHER UNE PRISE DE COURANT, la prise de courant doit tre installe prs du produit, afin dassurer une accessibilit scuritaire la prise de courant. 10. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 11. Dbranchez les cordons dalimentation avant de remplacer le bloc-piles. 12. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. 13. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 14. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 15. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. 16. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 17. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 18. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 19. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 20. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 21. Examinez les composantes afin de vrifier si celles-ci ne sont pas endommages. 22. Soyez avis de la perte de la confidentialit lorsque vous utilisez les ondes publiques. Les conversations peuvent tre entendues par dautres moniteurs de bb, des tlphones sans fil, des scanneurs, etc. 23. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. 24. Le produit nest pas conu pour tre utilis par des personnes (incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde 1. Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). 2. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu. 3. 4. Assurez-vous que le moniteur et le cordon de ladaptateur sont toujours hors de porte des enfants, au moins 1 mtre (3 pieds) de lenfant ou du berceau, pour viter tout risque de strangulation. 5. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. 6. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans Status icons Connection status the parent unit. and the parent unit. the parent unit. displays when strong signal strength is detected between the baby unit and displays when moderate signal strength is detected between the baby unit displays when the weak signal strength is detected between the baby unit and flashes when the link between the baby unit and the parent unit is lost. Night light On when the night light is turned on. Sound alert Displays when the sound alert of the parent unit is turned on. Flashes when there are loud sounds detected from the baby unit. Vibration alert Displays when the vibration alert of the parent unit is turned on. Flashes when there are loud sounds detected from the baby unit. Volume off Displays when the parent unit speaker volume is turned off. Battery status No battery icon displays when there is no battery installed. displays solid when the battery is fully charged. flashes when the battery is in low level and needs charging. animates when the battery is charging. Parent unit display screen messages LINKED The link between the parent unit and the baby unit is established. LOW BATTERY The parent unit uses only the rechargeable battery pack and it needs to be recharged. NOT LINKED The link between the parent unit and the baby unit is lost continuously for over 10 seconds. Both idle parent units are being paged by the baby unit. Your selection has been saved. SEARCHING The parent unit is out of range of the baby unit, or the baby unit is out of power. You are using the parent unit to talk to your baby. Someone is using the other parent unit to talk to the baby, and the voice is also broadcasting to your parent unit. No sound will transmit from the baby unit to any parent unit during broadcasting. For DM1212-2 only PAGING SAVED TALK TALKBACK fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil) :
Lorganisme Wireless Technology Research, LLC (WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:
Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. Limited warranty What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?
During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and representative of VTech; or antenna systems; or altered or rendered illegible; or