FCC ID: EW780-2367-00 Pan & Tilt Monitor

Important Safety Instructions The applied nameplate is located at the bottom of the baby units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Power adapter information:

Baby unit output: Output: 5V DC 1.5A; VTech Telecommunications Ltd.; Model: VT07EUS05150 Parent unit output: Output: 5V DC 2A; VTech Telecommunications Ltd.; Model: VT07EUS05200 Rechargeable battery information:

Zhuhai Great Power Energy Co., Ltd.; Lithium battery, 3.7V 5000mA; Model: GSP806090 8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. 11. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. Do not overload wall outlets or use an extension cord. 15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 19. You should test the sound reception every time you turn on the units or move one of the components. 20. Periodically examine all components for damage. 21. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 22. Children should be supervised to ensure that they do not play with the product. 23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between 32oF and 104oF. 2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire. 4. WarningStrangulation HazardChildren have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. 5. Never place the baby unit(s) inside the babys crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket. 6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This LeapFrog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Whats Included Parent Guide x 2 x 2 2. Power on or off the Baby Monitor 1. Slide the power switch to ON to power on your baby unit. 2. After the parent unit is fully charged, press until the welcoming screen and hold appears. 4. Positioning the Baby Monitor 1.

> 3ft (1m) 4. Key Features Color and B&W Automatic Night Vision Thanks to the latest starlight sensor and noise suppression technology, you can check in on your baby 24/7 with the finest clarity. Night vision is no longer just black and white, you can choose to see your baby in color at night!

Night Light Need some additional lighting near your baby for those bedtime stories? The built-in night light on the baby monitor can help with that. You can control the night light directly on the baby unit, or remotely from the parent unit. 360 Pan, Tilt, and Zoom Watch as your curious little one moves around. The camera pans up to 360 degrees side-to-side and tilts as many as 52 degrees up and down. Need more detail? The camera zooms up to 8 times. Lullabies and Soothing Sounds Comforting and engaging your baby can be done easily and from a distance. Choose from 6 lullabies and 4 soothing sounds to help lull your baby back to sleep. Humidity and Temperature Sensor Rest assured of the environment your baby is in with the built-in real-time temperature and humidity sensor. It lets you know when the room is outside a comfortable temperature range. Motion and Sound Sensor With adjustable alerts on noise or motion detected from the baby monitor, give yourself a peace of mind with an extra set of eyes. Get Started 1. Connect the baby monitor Notes:

The rechargeable battery in the parent unit is built-in. Use only the power adapters supplied with this product. Make sure the parent unit and the baby unit are not connected to the switch controlled electric outlets. Connect the power adapters in a vertical or floor mount position only. The adapters prongs are not designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children. To maintain compliance with the FCCs RF exposure guidelines, place the baby unit at least 20cm from nearby persons. Charge the parent unit battery before use When you have connected and turned on the parent unit, the battery charges automatically. Notes:

Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid

. It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging. The standby time varies depending on the sensitivity levels you set, your actual usage time and the age of the battery. The battery icon on the screen indicates the battery status (see the following table). Battery Indicators Battery Status Action The screen displays The light flashes. The battery icon becomes solid

. The battery has very little power left and may only be used for a short time. The battery is fully charged. Charge without interruption

(about 30 minutes). To keep the battery charged, connect it to AC power when not in use. Technical Specifications Overview - Parent Unit Frequency control Crystal controlled PLL synthesizer Transmit frequency Baby unit: 2.406-2.475GHz Channels LCD 32 7 Color LCD

(IPS 1200x800 pixels) Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirements Parent unit: 3.7V 5000mA Lithium-ion battery Baby unit power adapter: Output: 5V DC @ 1.5A Parent unit power adapter: Output: 5V DC @ 2A Credits:

The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Arrow keys

/ Return Press and hold to talk to the baby unit. While in a submenu, press to exit. Volume Press to view volume adjustment bar 8 9 Zoom Power 10 Microphone 11 Antenna 12 Power jack 13 RESET 14 Stand Force reboot the parent unit. 10 11 10 11 8 9 10 POWER LED light On / Off switch Temperature sensor Position the sensor horizontally for optimal usage. 11 Power jack 12 Wall mount holes 13 PAIR / Reset key The parent unit and baby unit(s) provided are already paired. 4 5 6 7 6 7 8 9 1 2 3 LED light On when the parent unit is linked to the baby unit. Flashes when the link to the baby unit is lost. Battery LED light Night Mode quick set key Select black and white or color night vision viewing mode. Adjust night light brightness. Overview - Baby Unit 6 7 8 9 6 7 8 9 10 11 Light sensor Camera Infrared LEDs Microphone Night light 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 Night light control key Press to turn the night light on or off. Press and hold to adjust night light brightness. 7 Speaker 1 2 3 4 5 Basic Operation - Parent Unit to open the volume adjustment Adjust parent units speaker volume 1. Press bar. 2. Press and to decrease the speaker volume. to increase the speaker volume Turn on/off the parent unit screen You can turn on or off the parent unit screen without powering off the parent unit. You will still be able to hear sounds from the baby unit. Press on the parent unit to turn off the Press any key on the parent unit to turn on screen. the screen again. Parent Unit Icons Main Menu Icons Monitoring mode (For LF920-2HD only) Talk to your baby via the baby unit 1. Press and hold the key. 2. When the icon displays on screen, speak to your parent unit. Your voice is transmitted to the baby unit. 3. When finished talking, release the key and hear your baby again. 12 13 12 13 12 13 Press and hold Zoom Press sequence is 1x to zoom in or out. The zoom

, 4x

, and 8x

, 2x

. Press Night light

Use the menu Press to enter the menu, choose a menu item, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity. While in the menu:

Press to scroll among the

, or

, menu options. Press to select an item, or to save a setting. Press Press to return to the live video. to go to the Help & Info page. Lullaby 1 set for LF920HD 2 sets for LF920-2HD

> 3ft (1m)

< 3ft (1m) Note:

To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers. Caution:

The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience a high-pitched screeching noise from your baby monitor while positioning:

- Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR

- Lower the volume of your parent unit. Current view status The baby unit number that is being viewed when in:

- Single Baby Unit mode.

- Patrol mode (* For LF920-2HD only).

- Split mode (* For LF920-2HD only). Split mode

(* For LF920-2HD only) Patrol mode

(* For LF920-2HD only) Black and white night vision is activated. Color night vision is activated. Motion detection and alert is turned on. Sound detection and alert is turned on. Melodies or soothing sounds are playing. Night light is turned on and the automatic brightness setting is turned off. Night light is turned on and the automatic brightness setting is turned on. Parent unit speaker is muted. Temperature alert is turned on. 5050 Humidity 2626CC Temperature Battery level indicator 2. 3. Press and hold 3. Status Check Once your baby unit and parent unit are powered on, your parent unit displays image from the baby unit, and the LED light of the baby unit also turns on. LED light turns on. The green

> 3ft (1m)

< 3ft (1m)

(See Sound Detection and Auto Wake Up sections) Status Bar Icons Baby unit 1 in Single mode Baby unit 2 in Single mode 1 2 Patrol mode Split mode 1 2 Turn on/off night light. Select auto brightness mode

(or) Adjust the fixed level night light brightness. LCD settings Melodies and Soothing Sounds Camera settings Select play all melodies, or play one of the five melodies and four soothing sounds. Lullaby Timer You can also set the timer to stop playing melodies after 15, 30, or 60 minutes, or play non-stop. General settings or Motion Turn on/off Motion Alert. Select motion Sensitivity level.

(See Motion Detection section) Temperature Turn on/off Temperature Alert. Set the parent unit to beep whenever the room temperature detected by the baby unit falls outside the set temperature range. Select the Minimum temperature for alert range. range. Select Maximum temperature for alert Select temperature Format. Set temperature to display in Fahrenheit

(oF) or Celsius (oC ). Adjust parent unit screen Brightness. Turn on/off Dim Mode. Turn on/off Status LED indicator. Set the Link, Battery, and Sound Level Indication LED lights on the parent unit to turn on or flash to indicate unit conditions. Adjust baby units speaker Volume. Turn on/off Low Battery Alert Tone. Set the parent unit to beep when the battery is low. Turn on/off No Link Alert Tone. Set the parent unit to beep when the link between the parent unit and the baby unit is lost. Detection Sound Select sound Sensitivity level. Turn on/off Sound Detection Alert. Turn on/off Auto Wake Up function. Touch and learn!Touch and learn!Read our complete warranty policy online at leapfrog.com/warranty.Visit our website for more information about our products, downloads, resources and more.leapfrog.comleapfrog.comLeapFrog Enterprises, Inc.,a subsidiary of VTech Holdings Limited.TM and 2021 LeapFrog Enterprises, Inc.All right reserved.LF920HD7 High Definition7 High DefinitionPan & Tilt MonitorPan & Tilt MonitorNeed help?Visit leapfrog.com/support Parent GuideThis guide contains important information.Please keep it for future reference. Parent Unit Icons (continued) Alert Icons Displays when the parent units battery is low and needs charging. Displays when motion is detected by a baby unit. Displays when sound is detected by a baby unit. Displays when the temperature detected by the baby unit exceeds the set maximum. Displays when the temperature detected by the baby unit is lower than the set minimum. Night Vision (B&W and Color) Night Vision Mode Description B&W night vision

- Suitable for extremely dark or low light environments. Color night vision

- Suitable for low-light room conditions with night light as an assisting light source. Notes Change your night vision viewing mode 1. Press the Night mode quick set key view the Night mode menu. 2. Press or to choose for black and white night vision viewing or night vision viewing. for color The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. When the images from the baby unit are in black and white, and appears on the screen. When the images from the baby unit are in color, appears on the screen. It is normal to see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment. When the infrared LEDs are on, it is normal for the images to be in black and white. Tip The video quality may vary depending on the surrounding environment and interfering factors like lightings, objects, colors and backgrounds. Adjust the baby units angle or place the baby unit at a higher elevation to prevent glare and blurry displays. Try the following (in the order listed) for a common cure:

1. Disconnect the power to the baby unit(s) and the parent unit. 2. Wait a few seconds before connecting power back to the baby unit(s) and the parent unit. 3. Turn on the baby unit(s) and the parent unit. 4. Wait for the parent unit to synchronize with the baby unit(s). Allow up to one minute for this to take place. The parent unit may not be connected to power. Insert the appliance plug into the power jack of the parent unit and put the adapter in a wall socket. Then, press the on the parent unit to establish connection with the baby unit. Power button The baby unit may not be connected to power. Insert the appliance plug into the power jack of the baby unit and put the adapter in a wall socket. Then, slide the On/Off switch on the baby unit to establish connection with the parent unit. Make sure your power source is not controlled by a wall switch. Symptom Try this Why does the baby monitor not respond normally?

Why doesnt the baby units and parent units power LED turn on when I switch on the units?

Why doesnt my parent unit charge when connected to AC power?

Why are my images in black and white?

The images are in black white during night-time or in a dark room when night vision is automatically activated. You can also choose to view your baby at night in color, see Night Vision (B&W and Color) to learn how. Why is the baby unit producing a high-

pitched noise?

The parent unit and baby unit(s) may be too close to each other.

- Move the parent unit away from the baby unit(s) until the noise stops; OR

- Turn down the volume of your parent unit. Why does the parent unit beep?

The baby unit(s) may be out of range. Move the parent unit closer to the baby unit(s) (but not less than 3 feet). The parent unit may not have enough battery for the parent unit to perform normally. Charge the parent unit until the battery icon becomes solid

. The temperature of your babys room may be too high or too low. Why cant I hear any sounds from the parent unit? Why cant I hear my baby cry?

The parent unit speaker volume may be too low or muted. Press adjustment menu, then press unit menu to change the parent units sound sensitivity to the highest level (level 5), see Sound Detection and Auto Wake Up. to increase the speaker volume. Or you can use the parent to open the volume Why cant I establish a connection? Why does my connection cut off every now and then?

Why are there sound interruptions?

The baby unit(s) may be out of range. Move the parent unit closer to the baby unit(s) (but not less than 3 feet). Other electronic and wireless products may cause intereference with your baby monitor. Try installing your baby monitor as far away from these devices as possible. If you powered on only one baby unit but have two paired to the parent unit, your parent unit may display have turned on via the menu. and the LINK LED light flashes. Switch to the baby unit you Sound Detection and Auto Wake Up Motion Detection Dim Mode Adjust Sound Detection Sensitivity You can turn on Sound Detection Alert and adjust the Sound Sensitivity to only detect your desired level of sounds. When detected, the parent unit screen turns on if it has been switched off or dimmed. Adjust Motion Detection Sensitivity You can turn on Motion Alert and adjust the Motion Sensitivity to only detect your desired level of motion. When detected, the parent unit screen turns on if it has been switched off or dimmed. The parent unit display will dim to conserve energy after 5 minutes of inactivity, in which there were neither any key pressed nor alert received from the baby unit. Mount the baby unit on a dry wall (optional) Notes Check for reception strength and the baby units viewing angle before drilling the holes. The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your baby units. When the baby unit detects sounds that exceed the chosen level, the parent unit screen turns on and the baby unit transmits the detected sounds to the parent unit. You will be able to see and hear your baby. When the baby unit detects motions that exceed the chosen level, the parent unit screen turns on and displays lives images from the baby unit. You will be able to see and hear your baby. If you have turned on Sound Detection Alert, the parent unit beeps when the baby unit detect sounds. If you have turned on Motion Alert, the parent unit beeps when the baby unit detect movements. Level 3 (Highest) Level 2 (Medium) Level 1 (Lowest) Level 3 (Highest) Level 2 (Medium) Level 1 (Lowest) Sound Sensitivity Level Description The parent unit screen and speaker turn on for very small sounds, including background noises from your babys room. The parent unit screen and speaker turn on for babbling and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds. The parent unit screen and speaker turn on only for loud crying or screeching sounds from your baby. The parent unit remains quiet when your baby makes soft sounds. The parent unit screen and speaker turn on for small motions, such as yawning or stretching. The parent unit screen and speaker turn on for normal daily motions, such as people walking around the house. The parent unit screen and speaker only turn on for large motions, such as children running or jumping around. For LF920-2HD Only Monitoring mode Motion Sensitivity Level Description 5 minutes of inactivity Press any button Sound Activated Screen and Audio - Auto Wake-Up When Auto Wake-Up is turned on, the parent unit screen stays off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen and speaker turn on automatically. The parent unit will then turn off again after no sound has been detected for a while. S o u n d d e t e c t e d a t B a by U n i t 1 Night Light Want a softer hue from the baby units night light to relax your little one? You can control the brightness of its glow remotely from your parent unit, or directly on the baby unit. Adjust the night light on the parent unit Adjust the night light on the baby unit 1 2 Change different views - Single CAM Select baby unit 1 view the image from the selected baby unit. or baby unit 2 to Change different views - Patrol located Tap the Night light control key on the top of the baby unit to turn on/off the night light. Tap and hold the Night light control key to adjust the night lights brightness. Select Patrol mode as your monitoring mode to alternately view the image from baby units seconds. every 10 and 10s 1. Place the wall mount bracket on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit). 3. Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole. 4. Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit. 2. If you drill the holes into a stud, go to step 3. If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall. 3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. OR 4. Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place. 1 2 If night vision is not activated, newly saved settings will apply the next time night vision is activated. to Notes:

If you have muted the parent unit speaker, only the parent unit screen will turn on when a sound is detected. If you have turned on Auto Wake Up but turned off Sound Detection Alert, the parent unit will wake up when the baby unit detects sounds that are louder than the chosen sound sensitivity level. Troubleshooting The RBRC seal For cETL compliance only Disclaimer and Limitation of Liability to to brighten the night light (or turn on 1. Press the Night mode quick set key view the Night mode menu. 2. Press the night light when it is switched off). Press to dim the night light (or turn off the night light when it is at the lowest brightness level).

- OR -

1. Press to enter the main menu. 2. Press and to select

, press 3. Press 4. Press and and to select

, press to choose the desired to brightness level, then press confirm your selection. Note If auto night light brightness has been selected, but the brightness was adjusted (either on the baby unit or the parent unit), auto brightness mode will automatically turn off and switch to the fixed level of brightness. Mesures de scurit importantes La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. Linstallation par un adulte est requise. 2. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilit du parent ou de la personne qui soccupe de lenfant. Ce produit pourrait cesser de fonctionner et, par consquent, vous ne devriez pas prsumer quil continuera de fonctionner correctement pendant une priode de temps donne. De plus, il ne sagit pas dun instrument mdical et ne devrait pas tre utilis comme tel. Ce produit est destin vous aider superviser votre bb. 5. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque dexplosion pourrait survenir si un mauvais type de pile est utilis pour lunit du parent. La pile ne peut pas tre soumise des tempratures extrmes leves ou basses et une faible pression dair haute altitude pendant lutilisation, lentreposage ou le transport. Llimination de la pile dans le feu ou dans un four chaud, ou lcrasement ou le dcoupage mcanique de la pile peuvent entraner une explosion. Laisser la pile dans un environnement temprature extrmement leve peut entraner une explosion ou la fuite dun liquide ou dun gaz inflammable. Une pile soumise une pression dair extrmement basse peut provoquer une explosion ou une fuite de liquide ou de gaz inflammable. liminer la pile usage conformment aux informations du Sceau RBRC. 7. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. 8. 9. Informations sur les adaptateurs lectriques :

Adaptateur de lunit du parent : Sortie : 5V DC 2A VTech Telecommunications Ltd. Modle: VT07EUS05150 Adaptateur de lunit du bb : Sortie : 5V DC 1.5A VTech Telecommunications Ltd. Modle: VT07EUS05200 3. 4. Informations sur les piles rechargeables :

Zhuhai Great Power Energy Co., Ltd. Lithium battery, 3.7V 5000mA;

Modle: GSP806090 Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. Pour les PRODUITS BRANCHER UNE PRISE DE COURANT, la prise de courant doit tre installe prs du produit, afin dassurer une accessibilit scuritaire la prise de courant. 10. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 11. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. 12. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 13. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 14. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. 15. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 16. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 17. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 18. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 19. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 21. 20. Examinez les composantes afin de vrifier si celles-ci ne sont pas endommages. Il existe un trs faible risque de perte de confidentialit avec certains appareils lectroniques (autres coute-bbs, tlphones sans fils etc.). Pour lviter, sassurer que le produit na jamais t utilis avant lachat, rinitialiser lunit de faon priodique, teindre lcoute-bb quand il nest pas en cours dutilisation. 22. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. 23. Le produit nest pas conu pour tre utilis par des personnes

(incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde 1. Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). 2. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu. Avertissement - Risque de strangulation

- Les enfants se sont TRANGLS dans des cordons. Gardez ce cordon hors de porte des enfants ( plus de 0,9 m). Nenlevez pas cette tiquette. 5. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. 6. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil) :

Lorganisme Wireless Technology Research, LLC (WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de LeapFrog est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. The RBRC seal on the Li-ion battery indicates that LeapFrog Enterprises, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area. LeapFrogs participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized LeapFrog product service centers. Please call 1 (800) 8 BATTERY for information on Li-ion battery recycling and disposal bans/restrictions in your area. LeapFrogs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY are registered trademarks of Call2recycle, Inc. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging. Change different views - Split 1 2 Select Split mode as your monitoring mode to view the images from both baby units at once. Note While in Split mode, you can press or baby unit 2

, and hear the sounds transmitted from the highlighted baby unit. or to highlight the view of the baby unit 1 5. You can maximize your baby units viewing angles by tilting the wall mount bracket. Hold the baby unit, and then rotate the knob in an anti-clockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the joint and secure the angle. LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. LeapFrog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect against data loss. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-3 (B)/NMB-3(B) Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Warranty: Please visit our website at leapfrog.com/legal for full details of the warranty provided in your country. Customer Support Visit our Consumer Support website 24 hours a day at:

U.S.: leapfrog.com/support C.A.: leapfrog.ca/support Or call our Customer Service number: 1 (800) 701-5327 in the U.S. and Canada during Customer Service hours Monday to Friday, 7am - 2pm PST Instructions for Care FOR INDOOR, DRY-LOCATION USE ONLY. To keep this product in good condition, follow these guidelines:

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). Do not spill liquid of any kind on this product or immerse the product in water as it may render it inoperative. Clean with a slightly damp cloth in cold water (do not use soap, detergent, or other chemicals). Keep food and beverages away from this product. Make sure the product is dry before you connect it Never try to dismantle the unit. to the power source again. Avoid prolonged exposure to extreme temperatures and direct sunlight or moisture. Avoid dropping the product or treating it roughly.

BU MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 IC: 1135B-80236700 FCC ID: EW780-2367-00 HVIN: 35-400347BU Model: LF920HD BU A/V I.C.T.E. SN:XXXXXXXXXXX MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 IC: 1135B-80236700 FCC ID: EW780-2367-00 HVIN: 35-400347BU Model: LF920HD BU MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 IC: 1135B-80236700 FCC ID: EW780-2367-00 HVIN: 35-400347BU MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 IC: 1135B-80236700 FCC ID: EW780-2367-00 HVIN: 35-400347BU Model: LF920-2HD BU Model: LF920-0HD BU A/V I.C.T.E. SN:XXXXXXXXXXX A/V I.C.T.E. SN:XXXXXXXXXXX A/V I.C.T.E. SN:XXXXXXXXXXX BU LBL 22X35 mm 50# PET

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration 23/F Tai Ping Ind Center Block 1, 57 Ting Kok Rd, Tai Po NT, Hong Kong Applicant Legal Business Name VTech Telecommunications Ltd Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name EW7 EW780-2367-00 Mr. Michael Tsui michael_tsui@vtech.com 852-26805398 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: May. 03, 2021 Print Name:

Title:

Michael Tsui Approbation Supervisor

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

VTech Telecommunications Ltd Date: 2021-01-12 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: EW780-2367-00 To whom it may concern:

We, the undersigned, hereby authorize SGS Hong Kong Limited and YW Yung in SGS Hong Kong Limited to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with VTech Telecommunications Ltd This authorization is valid until further written notice from the applicant. Name (Printed):Michael Tsui Signature:

On behalf of Company: VTech Telecommunications Ltd. Telephone: 852 2680 5398 Title: Approbation Supervisor

23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT Hong Kong To:

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: VTech Telecommunications Ltd Regarding: Confidentiality Request regarding application for FCC ID: EW780-2367-00 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Michael Tsui Signature:

On behalf of Company: VTech Telecommunications Ltd Telephone: 852-26805398 E-mail: michael_tsui@vtech.com Title: Approbation Supervisor

VTech Telecommunications Ltd Jan. 12, 2021 To whom it may concern, Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows:

Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout

(Others, please specify) The only differences between these models are the follows for marketing purpose:

Color Cosmetic details Trade name Model Number

(Others, please specify) Suffix (a, b,) represents Color code Packing configuration Others, please specify) a= any alphanumeric character or blank is presenting number of baby unit. b = any alphanumeric character or blank is presenting color option For the product subject to authorization under FCC Declaration of Conformity:

In addition, it is to confirm that all the below information 1) the U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual are the same but different in the following model numbers only:

Item no. New model Model Number Trade Name Remarks 1 2 3 4 5 YES YES YES YES YES LF920HD BU LF920-2HDBU LF920-abHD BU LF920-0HD BU LF920-0bHD BU leapfrog 1 Baby unit 2 Baby unit a Baby units 1 Baby units 1 Baby unit The sample being submitted to Intertek Testing Services for conformity assessment is LF920HD BU, (test model) of the above list. Regards, Michael Tsui Approbation Supervisor