FCC ID: EW780-1383-09 Video Baby Monitor

For more support information S m Quick start guide VM350 VM350-2 11/20. VM350-X_QSG_V5. 2020 VTech Communications, Inc. All rights reserved. Specifications are subject to change without notice. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. Credits:

Parent unit battery: 3.8V 2100mAh Li-ion battery Parent unit power adapter: Output: 5V DC @ 1A Baby unit power adapter: Output: 6V DC @ 400mA Power requirements may vary according to environmental conditions at the time of use. Nominal effective rangeMaximum power allowed by FCC and IC. Actual operating range

(WQVGA 480x272 pixel) 5 Color LCD 32 LCD Channels Parent unit: 2405 - 2475 MHz Baby unit: 2405 - 2475 MHz Transmit frequency Crystal controlled PLL synthesizer Frequency control Technical specifications Basic operation - Parent unit Adjust speaker volume Zoom Press VOL+ / VOL- to adjust your parent unit speaker volume. Press to zoom in or out.

6 3 6 3 Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news. VM350 VM350-2 Full Color Video Monitor Important safety instructions Whats in the box The applied nameplate is located at the bottom of the baby units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. CAUTION: Use only the batteries provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The batteries cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of batteries into fire or a hot oven, or mechanically crushing or cutting or the batteries can result in an explosion. Leaving the batteries in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Batteries subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. 7. Use only adaptors and batteries listed below. Power adapter information:

VTech Telecommunications Ltd. Model : VT05EUS06040 (Baby unit); VT05EUS05100

(Parent unit). Rechargeable batteries information:

ZHONGSHAN TIANMAO BATTERY CO., LTD 3.8V 2100mAh Li-ion Battery (Model: I9300) 8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Unplug the power cords before replacing batteries. 12. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 15. Do not overload wall outlets or use an extension cord. 16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 20. You should test the sound reception every time you turn on the units or move one of the components. 21. Periodically examine all components for damage. 22. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 23. Children should be supervised to ensure that they do not play with the product. 24. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between 32oF and 104oF. 2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire. 4. WarningStrangulation HazardChildren have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9 m) away). Do not remove this tag. 5. Never place the baby unit inside the babys crib or playpen. Never cover the baby unit or parent unit with anything such as a towel or a blanket. 6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. e t i u e q e r e s c o c u o n p n a a c r N o l

. a l a o c c l n a i a t s a N e a l e e l

. o i r b m e t e c d b n e d e l a a a d r d a l e r e e m n o i o g u u l u n f b m f g e a s i s n l c o s b e e i d n a a t p o e t

. e a i r R t c s e E

. s t e n t r s s t t e x u e q e i a t s o n e e o a e g n n i t o i u a n e s n n s l o e o e m c e t n l o e d a l d M s a

. s p p z s i o e m r r t e i t t n e m e L

. s s t e n t r i u o e t m n a u o N t

. n e e e l u f a e g n n

, e e s r o c l l e t t t o

. e n n e e f r e d e t o o D n

. o l i r s h h e c f t t m D

. d o a o i t l l n o i t d h e c c l a n t t a r a a a o e i l a u z g a n H r e s d f b l i n

. g o h e o t a t c t x t u s e e s a r t S o d h i n h d e r e o n t a t m h e c o t s d r i o v i r f w h o y m e t c a e p e s r w u e h a e T K s r s a s g e q n d v e u t r

. n o n e e d t i a o r a t f s e R r e n a u t d r t o c t i e d c d s e p q i n z t o u e d s i l i e t s t t z n e n o d u e c d e g r i N i o o p l c 1 set for VM350 2 sets for VM350-2 e t i u e q e r e s c o c u o n p n a a c r N o l

. a l a o c c l n a i a t s a N e a l e e l

. o i r b m e t e c d b n e d e l a a a d r d a l e r e e m n o i o g u u l u n f b m f g e a s i s n l c o s b e e i d n a a t p o e t

. e a i r R t c s e E

. s t e n t r s s t t e x u e q e i a t s o n e e o a e g n n i t o i u a n e s n n s l o e o e m c e t n l o e d a l d M s a

. s p p z s i o e m r r t e i t t n e m e L

. s s t e n t r i u o e t m n a u o N t

. n e e e l u f a e g n n

, e e s r o c l l e t t t o

. e n n e e f r e d e t o o D n

. o l i r s h h e c f t m t D

. d o a o i t l l n o i t d h e c c l a n t t a r a a a o e i l a u z g a n H r e s d f b l i n

. g o h e o t a t c t x t u s e e s a r t S o d h i n h d e r e o n t a t m h e c o t s d r i o v i r f w h o y m e t c a e p e s r w u e h a e T K s r s a s g e q n d v e u t r

. n o n e e d t i a o r a t f s e R r e n a u t d r t o c t i e d c d s e p q i n z t o u e d s i l i e t s t t z n e n o d u e c d e g r i N i o o p l c Quick start guide 1 Connect the baby monitor Install the battery The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only. NOTENotes NOTES possible leakage Use only the battery supplied with this product. If the parent unit will not be used for a long time, disconnect and remove the battery to prevent 2 3 THIS SIDE UP Press down on the battery compartment cover to pull it out. Make sure the label THIS SIDE UP is facing up while inserting the battery. Replace the battery To replace the battery, press down on the battery compartment cover and pull it out, then follow the steps above to install the battery. Connect the baby monitor NOTENotes NOTES Use only the power adapters supplied with this product. Make sure the baby monitor is not connected to the switch controlled electric outlet. Connect the power adapters in a vertical or floor mount position only. The adapters prongs are not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-

the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children. Caution babys crib or playpen.

> 3ft (1m) 3 Positioning the baby monitor Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the

> 3ft (1m)

< 3ft (1m) Caution The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience high-pitched screeching noise from your baby monitor while positioning:

- Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR

- Lower the volume of your parent unit. 3ft (1m)

< 3ft (1m) NOTENote NOTES To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers. e s t a e t i q u e t a

. c o n u n a e x t e n s i n i l n a m b r i c a

. N o q u i t e d e l i n o e n t o d o m o m e n t o

. N o l o u s e l o m e n o s t r e s p e s f u e r a d e i l a a l c a n c e d e l i o s n o s

. l E s t e c a b e d e b e e s t a r p o r M a n t e n g a e s t e c a b e f u e r a d e l l a a l c a n c e e s t r a n g u l a c i n R i e s g o d e c e t t e t i q u e t t e

. i l o g n e z c e c o r d o n d e s e n f a n t s

. L e i p e d s d u n e n f a n t e t c e

, e n t o u t t e m p s

. c o r d o n d o i t s e t r o u v e r a u m o n s t r o i s i N u t i l i s e z p a s d e r a l l o n g e

. N e r e t i r e z p a s d t r a n g l e m e n t R i s q u e r e m o v e t h i s t a g

. u s e w i t h a n e x t e n s i o n c o r d

. D o n o t a w a y f r o m t h e c h i l d a t a l l t i m e s

. D o n o t T h e c o r d n e e d s t o b e a t l e a s t t h r e e f e e t K e e p t h i s c o r d o u t o f r e a c h o f c h i l d r e n

. H a z a r d S t r a n g u l a t i o n Strangulation Hazard Keep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag. Risque dtranglement loignez ce cordon des enfants. Le cordon doit se trouver au moins trois pieds dun enfant et ce, en tout temps. Nutilisez pas de rallonge. Ne retirez pas cette tiquette. Riesgo de estrangulacin Mantenga este cable fuera de la alcance de los nios. Este cable debe estar por lo menos tres pies fuera de la alcance del nio en todo momento. No lo use con una extensin inalmbrica. No quite esta etiqueta. NOTENotes NOTES the battery. Charge the parent unit battery When you have connected and turned on the parent unit, the battery will be charged automatically. Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid

. It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging. The standby time varies depending on the sensitivity level you set, your actual use and the age of 2 Power on or off the baby monitor Slide the ON/OFF switch to power on or off your baby unit. Press and hold POWER to power on or off your parent unit. 4 Status check Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on. The POWER LED light of baby unit turns on. Long press 6 3 Long press Power on Power off Use the menu to enter the menu, choose a menu item, or save a Press setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity. or While in the menu:

Press Press Press or to scroll among the menu options. to select an item, or to save a setting. to scroll among the sub-menus, or to adjust a setting. Press to return to the previous menu options without changing the current setting. Press

/EXIT to return to live video. Overview - Parent unit Pair hole Your baby units and parent unit provided are already paired. POWER LED light On when the baby unit is turned on and is paired to the parent unit. Flashes when the baby unit is not being viewed;

or when the link to the parent unit is lost. Slide to turn on or off the baby 6 7 8 9 Light sensor ON/OFF switch unit. Speaker Power jack 10 Wall mount holes Talk to your baby unit Turn off the screen Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when finish talking and hear your baby again. Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the baby unit. 6 3 Long press 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3 Microphone Camera Infrared LEDs Need help?

Long press Tip Press any keys on the parent unit to turn on the screen again. 1 2 3 4 5 6 LCD display Antenna LED lights Microphone POWER TALK 7 8 9 10 11 12 Arrow keys MENU/SELECT Power jack VOL - / VOL +

VIEW /LCD ON/OFF

/EXIT Speaker 13 14 Battery compartment cover 15 Stand For operations and guides to help you using your video monitor, and for latest information and supports, go and check the online help topics and online FAQs. S m Use your smartphone or mobile device to access our online help. Go to https://help.vtechphones.com/vm350 or https://help.vtechphones.com/vm350-2; OR Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the devices camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help.

If the QR code is not clearly displayed, adjust your cameras focus by moving your device closer or further away until it is clear. You can also call our Customer Support at 1 (800) 595-9511 [in US] or 1 (800) 267-7377 [in Canada] for help. VM350 VM350-2 Overview - Baby unit Parent unit icons 8 9 1 2 7 10 Adjust the parent units LCD brightness. Main menu Sub-menu Alert tones Main menu Sub-menu Sound activation - screen and audio

Turn on/off sound activation Main menu icons Sub-menu Main menu Brightness Camera settings Lullaby

Play/Stop lullaby Baby unit speaker volume Adjust the baby units speaker volume. Monitoring mode (For VM350-2 only) Single mode Split mode Patrol mode Select one of the soothing sounds, or white noise. Select one of the five melodies. Play all melodies. Set timer to stop playing the selected melody or soothing sound. Turn on/off the alert vibration. Temperature

VOX (Voice Activated Alert) Sensitivity Set the parent unit to beep when the battery is low. Set the parent unit to beep when the link between the parent unit and the baby unit is lost. Set the confirmation tone on or off when selecting an option in the menus. Set the parent unit to beep when the baby unit detects sounds while in Split mode (For VM350-2 only). Turn on/off temperature alert tone. Set the parent unit to beeps whenever the room temperature detected by the baby unit falls outside of the set temperature range. Set the minimum temperature. Set the maximum temperature. Set temperature display in Fahrenheit (oF) or Celsius (oC) Set sound activation on or off. When it is on, and the baby unit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection. NOTENote NOTES When the parent unit screen is off and it receives alerts, for example, link lost between parent unit and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds. You can set VOX sensitivity level to activate parent unit screen and sound when baby unit detects sounds that exceed certain levels. See Sound sensitivity and sound activation section. 1 3 4 5 6 1 2 4 5 Parent unit icons (Contd) Sound sensitivity and sound activation Night vision Adjust sound detection sensitivity You can turn on Sound activation and adjust the VOX sensitivity to detect sounds and turn on the parent unit while its screen is switched off or dimmed. When the baby unit detects sounds that exceed certain levels, the parent unit screen will turn on and the baby unit starts transmitting the sounds to the parent unit, and you can see and hear your baby. If you turn off Sound activation, you will hear sounds from the baby unit all the time, even when the parent unit screen is switched off. If you have turned on sound alert, the parent unit beeps when the baby unit detect sounds while in Split mode (*For VM350-2 only). VOX Sensitivity level Level 5

(Highest) Level 4

(High) Level 3

(Medium) Level 2

(Low) Level 1

(Lowest) Description (Default setting) The parent unit screen and speaker turn on for very small sounds, including background noises from your babys room. The parent unit screen and speaker turn on for soft babbling and louder sounds from your baby. The parent unit remains quiet when your baby sleeps soundly. The parent unit screen and speaker turns on for loud babbling and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds. The parent unit screen and speaker turn on for crying and louder sounds from your baby. The parent unit remains quiet when your baby makes soft sounds. The parent unit screen and speaker turn on for loud crying or screeching sounds from your baby. The parent unit remains quiet when your baby makes soft sounds. For VM350-2 only Status check - Two baby units If you are viewing baby unit

, the POWER LED light of baby unit turns on. As baby unit is not being viewed, its POWER LED light flashes. NOTENote NOTES the LINK LED light flashing. If you power on only one baby unit, you may see the parent unit displaying and then

, and Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on. Change different views - Single CAM The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen. It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment. When the infrared LEDs are on, the images are in black and white. This is normal. Notes Tip Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the video quality may vary. Adjust the baby units angle or place the baby unit at a higher level to prevent glare and blurry display. Dim mode Press VIEW The parent unit display will dim to conserve energy after 10 minutes of inactivity, in which there is neither key pressed nor alert received from the baby unit. Change different views - Patrol Change different views - Split In Single CAM or Patrol mode, press VIEW to switch between the image of baby units and

. Sound activated screen and audio When Sound activation is on, the parent unit screen stays off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen and speaker turn on automatically. The parent unit will then turn off again after 50 seconds of no sound detection. NOTENote NOTES If you have muted the parent unit speaker, only the parent unit screen will turn on when a sound is detected. 6 3 10 min inactivity Select Patrol as your monitoring mode to alternately view the image from baby units and every 10 seconds. Select Split as your monitoring mode to view the images from both baby units at once. Press any buttons 10s Status icons Status icons Connection status

- Strong signal strength.

- Moderate signal strength.

- Low signal strength.

- Weak signal strength. Split mode

(*For VM350-2 only) Patrol mode

(*For VM350-2 only) or Current view status The baby unit number that is being viewed when in:

Alert icons oF or oC

- Single CAM mode.

- Patrol mode

(*For VM350-2 only).

- Split mode

(*For VM350-2 only). Night vision - On Zoom - On Lullaby - On Real-time temperature Real-time temperature detected by the baby unit in Fahrenheit (oF) or Celsius (oC)

(e.g. 57 oF or 14 oC). Temperature alert tone - On 9-level sound indicator indicates low sound level detected by the baby unit. indicates moderate sound level detected by the baby unit. indicates high sound level detected by the baby unit. Mute alert Displays when the parent unit speaker volume is set to off. Displays when the parent unit is talking to the baby unit. Battery status animates when the battery is charging.

- battery is fully charged.

- battery is low and needs charging. Displays when parent units battery is low and needs charging. Displays when connection between parent unit and baby unit is lost. Displays when sound is detected at a baby unit when in Split view.

(For VM350-2 only) Baby unit detects temperature reaches or exceeds the set maximum. Baby unit detects temperature is at or is lower than the set minimum. Mount the baby unit on dry wall (optional) Items to purchase You will need to purchase the following items separately to mount your baby unit:

2 screws 2 anchors Note NOTES NOTE The types of screws and anchors you need depend on the composition of the wall. Drill two holes in the wall. If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall. Align the wall mount holes at the bottom of the baby unit with the screws on the wall. Slide the baby unit down until it locks into place. Note NOTES NOTE Check for reception strength and camera angle before drilling the holes. Use a pencil to mark two holes in parallel. Make sure they are the same distance apart as the wall mount holes on the baby unit. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. Adjust the camera angle. The RBRC seal For cETL compliance only The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Ni-MH batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC seal and 1-800-8-BATTERY are registered trademarks of Call2recycle, Inc. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging. Mesures de scurit importantes La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. Linstallation par un adulte est requise. 2. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilit du parent ou de la personne qui soccupe de lenfant. Ce produit pourrait cesser de fonctionner et, par consquent, vous ne devriez pas prsumer quil continuera de fonctionner correctement pendant une priode de temps donne. De plus, il ne sagit pas dun instrument mdical et ne devrait pas tre utilis comme tel. Ce produit est destin vous aider superviser votre bb. 5. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque dexplosion si un autre type de batterie est utilis pour lunit Parents. Nincinrez pas les piles. Celles-

ci risqueraient dexploser. Jetez les piles uses selon les renseignements suivant le sceau du RBRC. 7. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. 8. 9. Informations sur les adaptateurs lectriques :

Adaptateur de lunit du parent : Sortie : 5V CC 1A VTech Telecommunications Ltd. Modle : VT05EUS05100 Adaptateur de lunit du bb : Sortie : 6V CC 400mA VTech Telecommunications Ltd. Modle : VT05EUS06040 Informations sur les piles rechargeables :

ZHONGSHAN TIANMAO BATTERY CO., LTD 3.8V 2100mAh Li-ion Battery (Model: I9300) Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. Pour les PRODUITS BRANCHER UNE PRISE DE COURANT, la prise de courant doit tre installe prs du produit, afin dassurer une accessibilit scuritaire la prise de courant. 10. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 11. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. 12. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 13. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 14. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. 15. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 16. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 3. 4. 17. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-

circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 18. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 19. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 20. Examinez les composantes afin de vrifier si celles-ci ne 21. sont pas endommages. Il existe un trs faible risque de perte de confidentialit avec certains appareils lectroniques (autres coute-bbs, tlphones sans fils etc.). Pour lviter, sassurer que le produit na jamais t utilis avant lachat, rinitialiser lunit de faon priodique, teindre lcoute-bb quand il nest pas en cours dutilisation. 22. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. 23. Le produit nest pas conu pour tre utilis par des personnes (incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde 1. Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). 2. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu. Avertissement - Risque de strangulation

- Les enfants se sont TRANGLS dans des cordons. Gardez ce cordon hors de porte des enfants ( plus de 0,9 m). Nenlevez pas cette tiquette. 5. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. 6. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil) :

Lorganisme Wireless Technology Research, LLC (WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. Limited warranty What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and 2. Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase.

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ201020002-RF EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com FCC Confidential Authorization Date: 2020/11/17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: EW780-1383-09 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, VTech Telecommunications Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com FCC Authorization Date: 2020/11/17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, VTech Telecommunications Ltd, the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, This authorization is valid until further written notice from the applicant. 21 U.S.C. 862. Sincerely Yours, Signature Michael Tsui Approbation Supervisor QA-FR-170-B

VTech Telecommunications Ltd November 12, 2020 To whom it may concern, Multiple Models Confirmation Letter-BU I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows:

Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout

(Others, please specify) The only differences between these models are the follows for marketing purpose:

Color Cosmetic details Trade name Model Number

(Others, please specify) Model VM3256-ab BU/ VM819-ab BU is identical to model VM350-ab BU except for model designation and appearance. Suffix (a, b) represents Color code Packing configuration Others, please specify) . a=any alphanumeric character or blank is presenting number of baby unit. b = any alphanumeric character or blank is presenting color of enclosure. For the product subject to authorization under FCC Declaration of Conformity:

In addition, it is to confirm that all the below information 1) the U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual are the same but different in the following model numbers only:

Item No. New model Model Number Trade Name Remarks 1 2 3 4 5 6 7 8 9 YES YES YES YES YES YES YES YES YES VM350 BU VM350-2 BU VM350-ab BU VM3256 BU VM3256-2 BU VM3256-ab BU VM819 BU VM819-2 BU VM819-ab BU vtech vtech vtech vtech vtech vtech vtech vtech vtech 1 baby unit 2 baby unit a baby unit 1 baby unit 2 baby unit a baby unit 1 baby unit 2 baby unit a baby unit The sample being submitted to Bay Area Compliance Labs Corp.(Shenzhen) for conformity assessment is VM350 BU (test model) of the above list. All above model's FCC ID is EW780-1383-09, IC is 1135B-80138309. Regards, Michael Tsui Approbation Supervisor